Abstract: Bidirectional energy transfer capability with high efficiency and reduced cost is fast gaining prominence in the central part of a lot of power conversion systems in Direct Current (DC) microgrid. Preferably, under the economics constraints, these systems utilise a single high efficiency power electronics conversion system and a dual active bridge converter. In this paper, modeling and performance of Dual Active Bridge (DAB) converter with Extended Phase Shift (EPS) is evaluated with two batteries on both sides of DC bus and bidirectional energy transfer is facilitated and this is further compared with the Single Phase Shift (SPS) mode of operation. Optimum operating zone is identified through exhaustive simulations using MATLAB/Simulink and SimPowerSystem software. Reduced rules based fuzzy logic controller is implemented for closed loop control of DAB converter. The control logic enables the bidirectional energy transfer within the batteries even at lower duty ratios. Charging and discharging of batteries is supervised by the fuzzy logic controller. State of charge, current and voltage for both the batteries are plotted in the battery characteristics. Power characteristics of batteries are also obtained using MATLAB simulations.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim
Abstract: A linear feedback shift register (LFSR) is proposed which targets to reduce the power consumption from within. It reduces the power consumption during testing of a Circuit Under Test (CUT) at two stages. At first stage,
Control Logic (CL) makes the clocks of the switching units
of the register inactive for a time period when output from
them is going to be same as previous one and thus reducing
unnecessary switching of the flip-flops. And at second stage,
the LFSR reorders the test vectors by interchanging the bit
with its next and closest neighbor bit. It keeps fault coverage
capacity of the vectors unchanged but reduces the Total Hamming Distance (THD) so that there is reduction in power
while shifting operation.
Abstract: This paper describes the design of a real-time audiorange
digital oscilloscope and its implementation in 90nm CMOS
FPGA platform. The design consists of sample and hold circuits,
A/D conversion, audio and video processing, on-chip RAM, clock
generation and control logic. The design of internal blocks and
modules in 90nm devices in an FPGA is elaborated. Also the key
features and their implementation algorithms are presented.
Finally, the timing waveforms and simulation results are put
forward.
Abstract: Component handling system is one of the important sub systems of Prototype Fast Breeder Reactor (PFBR) used for fuel handling. Core handling system is again a sub system of component handling system. Core handling system consists of in-vessel and ex-vessel subassembly handling. In-vessel core handling involves transfer arm, large rotatable plug and small rotatable plug operations. Modeling and simulation of in-vessel core handling is a part of development of Prototype Fast Breeder Reactor Operator Training Simulator. This paper deals with simulation and modeling of operations of transfer arm, large rotatable plug and small rotatable plug needed for in-vessel core handling. Process modeling was developed in house using platform independent Cµ code with OpenGL (Open Graphics Library). The control logic models and virtual panel were modeled using simulation tool.
Abstract: The Programmable Logic Controller (PLC) plays a
vital role in automation and process control. Grafcet is used for
representing the control logic, and traditional programming
languages are used for describing the pure algorithms. Grafcet is used
for dividing the process to be automated in elementary sequences that
can be easily implemented. Each sequence represent a step that has
associated actions programmed using textual or graphical languages
after case. The programming task is simplified by using a set of
subroutines that are used in several steps. The paper presents an
example of implementation for a punching machine for sheets and
plates. The use the graphical languages the programming of a
complex sequential process is a necessary solution. The state of
Grafcet can be used for debugging and malfunction determination.
The use of the method combined with a set of knowledge acquisition
for process application reduces the downtime of the machine and
improve the productivity.
Abstract: In this study, we experiment on precise control outlet
temperature of water from the water cooler with hot-gas bypass
method based on PI control logic for machine tool. Recently, technical
trend for machine tools is focused on enhancement of speed and
accuracy. High speedy processing causes thermal and structural
deformation of objects from the machine tools. Water cooler has to be
applied to machine tools to reduce the thermal negative influence with
accurate temperature controlling system. The goal of this study is to
minimize temperature error in steady state. In addition, control period
of an electronic expansion valve were considered to increment of
lifetime of the machine tools and quality of product with a water
cooler.
Abstract: As business environments are rapidly changing,
the manufacturing system must be reconfigured to adapt to
various customer needs. In order to cope with this challenge, it
is quintessential to test industrial control logic rapidly and
easily in the design time, and monitor operational behavior in
the run time of automated manufacturing system. Proposed
integrated model for virtual prototyping and operational
monitoring of industrial control logic is to improve limitations
of current ladder programming practices and general discrete
event simulation method. Each plant layout model using HMI
package and object-oriented control logic model is designed
independently and is executed simultaneously in integrated
manner to reflect design practices of automation system in the
design time. Control logic is designed and executed using UML
activity diagram without considering complicated control
behavior to deal with current trend of reconfigurable
manufacturing. After the physical installation, layout model of
virtual prototype constructed in the design time is reused for
operational monitoring of system behavior during run time.