Abstract: Analytical investigation of the free vibration behavior
of circular functionally graded (FG) plates integrated with two
uniformly distributed actuator layers made of piezoelectric (PZT4)
material on the top and bottom surfaces of the circular FG plate
based on the classical plate theory (CPT) is presented in this paper.
The material properties of the functionally graded substrate plate are
assumed to be graded in the thickness direction according to the
power-law distribution in terms of the volume fractions of the
constituents and the distribution of electric potential field along the
thickness direction of piezoelectric layers is simulated by a quadratic
function. The differential equations of motion are solved analytically
for clamped edge boundary condition of the plate. The detailed
mathematical derivations are presented and Numerical investigations
are performed for FG plates with two surface-bonded piezoelectric
layers. Emphasis is placed on investigating the effect of varying the
gradient index of FG plate on the free vibration characteristics of the
structure. The results are verified by those obtained from threedimensional
finite element analyses.
Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: The normalized difference vegetation index (NDVI)
and normalized difference moisture index (NDMI) derived from the
moderate resolution imaging spectroradiometer (MODIS) have been
widely used to identify spatial information of drought condition. The
relationship between NDVI and NDMI has been analyzed using
Pearson correlation analysis and showed strong positive relationship.
The drought indices have detected drought conditions and identified
spatial extents of drought. A comparison between normal year and
drought year demonstrates that the amplitude analysis considered both
vegetation and moisture condition is an effective method to identify
drought condition. We proposed the amplitude analysis is useful for
quick spatial assessment of drought information at a regional scale.
Abstract: In this paper, we have focused on study of swelling kinetics and salt-sensitivity behavior of a superabsorbing hydrogel based on carboxymethylcellulose (CMC) and acrylic acid and 2- Buthyl methacrylate. The swelling kinetics of the hydrogels with various particle sizes was preliminary investigated as well. The swelling of the hydrogel showed a second order kinetics of swelling in water. In addition, swelling measurements of the synthesized hydrogels in various chloride salt solutions was measured. Results indicated that a swelling-loss with an increase in the ionic strength of the salt solutions.
Abstract: Explosive forming is one of the unconventional
techniques in which, most commonly, the water is used as the
pressure transmission medium. One of the newest methods in
explosive forming is gas detonation forming which uses a normal
shock wave derived of gas detonation, to form sheet metals. For this
purpose a detonation is developed from the reaction of H2+O2
mixture in a long cylindrical detonation tube. The detonation wave
goes through the detonation tube and acts as a blast load on the steel
blank and forms it. Experimental results are compared with a finite
element model; and the comparison of the experimental and
numerical results obtained from strain, thickness variation and
deformed geometry is carried out. Numerical and experimental
results showed approximately 75 – 90 % similarity in formability of
desired shape. Also optimum percent of gas mixture obtained when
we mix 68% H2 with 32% O2.
Abstract: This paper presents the design and implementation of
the WebGD, a CORBA-based document classification and retrieval
system on Internet. The WebGD makes use of such techniques as Web,
CORBA, Java, NLP, fuzzy technique, knowledge-based processing
and database technology. Unified classification and retrieval model,
classifying and retrieving with one reasoning engine and flexible
working mode configuration are some of its main features. The
architecture of WebGD, the unified classification and retrieval model,
the components of the WebGD server and the fuzzy inference engine
are discussed in this paper in detail.
Abstract: In order to develop forest management strategies in
tropical forest in Malaysia, surveying the forest resources and
monitoring the forest area affected by logging activities is essential.
There are tremendous effort has been done in classification of land
cover related to forest resource management in this country as it is a
priority in all aspects of forest mapping using remote sensing and
related technology such as GIS. In fact classification process is a
compulsory step in any remote sensing research. Therefore, the main
objective of this paper is to assess classification accuracy of
classified forest map on Landsat TM data from difference number of
reference data (200 and 388 reference data). This comparison was
made through observation (200 reference data), and interpretation
and observation approaches (388 reference data). Five land cover
classes namely primary forest, logged over forest, water bodies, bare
land and agricultural crop/mixed horticultural can be identified by
the differences in spectral wavelength. Result showed that an overall
accuracy from 200 reference data was 83.5 % (kappa value
0.7502459; kappa variance 0.002871), which was considered
acceptable or good for optical data. However, when 200 reference
data was increased to 388 in the confusion matrix, the accuracy
slightly improved from 83.5% to 89.17%, with Kappa statistic
increased from 0.7502459 to 0.8026135, respectively. The accuracy
in this classification suggested that this strategy for the selection of
training area, interpretation approaches and number of reference data
used were importance to perform better classification result.
Abstract: In this paper, we propose a fully-utilized, block-based 2D DWT (discrete wavelet transform) architecture, which consists of four 1D DWT filters with two-channel QMF lattice structure. The proposed architecture requires about 2MN-3N registers to save the intermediate results for higher level decomposition, where M and N stand for the filter length and the row width of the image respectively. Furthermore, the proposed 2D DWT processes in horizontal and vertical directions simultaneously without an idle period, so that it computes the DWT for an N×N image in a period of N2(1-2-2J)/3. Compared to the existing approaches, the proposed architecture shows 100% of hardware utilization and high throughput rates. To mitigate the long critical path delay due to the cascaded lattices, we can apply the pipeline technique with four stages, while retaining 100% of hardware utilization. The proposed architecture can be applied in real-time video signal processing.
Abstract: The sensitivity of orifice plate metering to disturbed
flow (either asymmetric or swirling) is a subject of great concern to
flow meter users and manufacturers. The distortions caused by pipe
fittings and pipe installations upstream of the orifice plate are major
sources of this type of non-standard flows. These distortions can alter
the accuracy of metering to an unacceptable degree. In this work, a
multi-scale object known as metal foam has been used to generate a
predetermined turbulent flow upstream of the orifice plate. The
experimental results showed that the combination of an orifice plate
and metal foam flow conditioner is broadly insensitive to upstream
disturbances. This metal foam demonstrated a good performance in
terms of removing swirl and producing a repeatable flow profile
within a short distance downstream of the device. The results of using
a combination of a metal foam flow conditioner and orifice plate for
non-standard flow conditions including swirling flow and asymmetric
flow show this package can preserve the accuracy of metering up to
the level required in the standards.
Abstract: An envelope echo signal measurement is proposed in
this paper using echo signal observation from the 200 kHz echo
sounder receiver. The envelope signal without any object is compared
with the envelope signal of the sphere. Two diameter size steel ball
(3.1 cm & 2.2 cm) and two diameter size air filled stainless steel ball
(4.8 cm & 7.4 cm) used in this experiment. The target was positioned
about 0.5 m and 1.0 meter from the transducer face using nylon rope.
From the echo observation in time domain, it is obviously shown that
echo signal structure is different between the size, distance and type
of metal sphere. The amplitude envelope voltage for the bigger
sphere is higher compare to the small sphere and it confirm that the
bigger sphere have higher target strength compare to the small
sphere. Although the structure signal without any object are different
compare to the signal from the sphere, the reflected signal from the
tank floor increase linearly with the sphere size. We considered this
event happened because of the object position approximately to the
tank floor.
Abstract: Metallic micro parts are playing an important role in micro-fabrication industry. Recently, we have demonstrated a new deformation mechanism for micro-formability of polycrystalline materials. Different depressed micro-features smaller than the grain size have been successfully fabricated on 6061 aluminum alloy (AA6061) substrates with good fidelity. To further verify this proposed deformation mechanism that grain size is not a limiting factor, we demonstrate here that in addition of depressed features, protruded micro-features on a polycrystalline substrate can similarly be fabricated.
Abstract: This paper analysed the food security situation among
Nigerian rural farmers. Data collected on 202 rural farmers from
Benue State were analysed using descriptive and inferential statistics.
The study revealed that majority of the respondents (60.83%) had
medium dietary diversity. Furthermore, household daily calorie
requirement for the food secure households was 10,723 and the
household daily calorie consumption was 12,598, with a surplus
index of 0.04. The food security index was 1.16. The Household
daily per capita calorie consumption was 3,221.2. For the food
insecure households, the household daily calorie requirement was
20,213 and the household daily calorie consumption was 17,393. The
shortfall index was 0.14. The food security index was 0.88. The
Household daily per capita calorie consumption was 2,432.8. The
most commonly used coping strategies during food stress included
intercropping (99.2%), reliance on less preferred food (98.1%),
limiting portion size at meal times (85.8%) and crop diversification
(70.8%).
Abstract: Testable software has two inherent properties – observability and controllability. Observability facilitates observation of internal behavior of software to required degree of detail. Controllability allows creation of difficult-to-achieve states prior to execution of various tests. In this paper, we describe COTT, a Controllability and Observability Testing Tool, to create testable object-oriented software. COTT provides a framework that helps the user to instrument object-oriented software to build the required controllability and observability. During testing, the tool facilitates creation of difficult-to-achieve states required for testing of difficultto- test conditions and observation of internal details of execution at unit, integration and system levels. The execution observations are logged in a test log file, which are used for post analysis and to generate test coverage reports.
Abstract: PARIS (Personal Archiving and Retrieving Image
System) is an experiment personal photograph library, which includes
more than 80,000 of consumer photographs accumulated within a
duration of approximately five years, metadata based on our proposed
MPEG-7 annotation architecture, Dozen Dimensional Digital Content
(DDDC), and a relational database structure. The DDDC architecture
is specially designed for facilitating the managing, browsing and
retrieving of personal digital photograph collections. In annotating
process, we also utilize a proposed Spatial and Temporal Ontology
(STO) designed based on the general characteristic of personal
photograph collections. This paper explains PRAIS system.
Abstract: The mechanical and tribological properties in WC-Co
coatings are strongly affected by hardness and elasticity
specifications. The results revealed the effect of spraying distance on
microhardness and elasticity modulus of coatings. The metallurgical
studies have been made on coated samples using optical microscopy,
scanning electron microscopy (SEM).
Abstract: Several trillion cigarettes produced worldwide annually lead to many thousands of kilograms of toxic waste. Cigarette butts (CBs) accumulate in the environment due to the poor biodegradability of the cellulose acetate filters. This paper presents some of the results from a continuing study on recycling CBs into fired clay bricks. Physico-mechanical properties of fired clay bricks manufactured with different percentages of CBs are reported and discussed. The results show that the density of fired bricks was reduced by up to 30 %, depending on the percentage of CBs incorporated into the raw materials. Similarly, the compressive strength of bricks tested decreased according to the percentage of CBs included in the mix. The thermal conductivity performance of bricks was improved by 51 and 58 % for 5 and 10 % CBs content respectively. Leaching tests were carried out to investigate the levels of possible leachates of heavy metals from the manufactured clay-CB bricks. The results revealed trace amounts of heavy metals.
Abstract: Sandwich panels are widely used in the construction
industry for their ease of assembly, light weight and efficient thermal
performance. They are composed of two RC thin outer layers
separated by an insulating inner layer. In this research the inner
insulating layer is made of lightweight Autoclaved Aerated Concrete
(AAC) blocks which has good thermal insulation properties and yet
possess reasonable mechanical strength. The shear strength of the
AAC infill is relied upon to replace the traditionally used insulating
foam and to provide the shear capacity of the panel. A
comprehensive experimental program was conducted on full scale
sandwich panels subjected to bending. In this paper, detailed
numerical modeling of the tested sandwich panels is reported. Nonlinear
3-D finite element modeling of the composite action of the
sandwich panel is developed using ANSYS. Solid elements with
different crashing and cracking capabilities and different constitutive
laws were selected for the concrete and the AAC. Contact interface
elements are used in this research to adequately model the shear
transfer at the interface between the different layers. The numerical
results showed good correlation with the experimental ones
indicating the adequacy of the model in estimating the loading
capacity of panels.
Abstract: The present study based on removal of natural dyes of
Roselle petals, then used Roselle petals powder (RPP) as an
adsorbent for the removal of methylene blue dye (as a typical cationic
or basic dye) from aqueous solutions. The present study shows that
used Roselle petals powder exhibit adsorption trend for the dye. The
adsorption processes were carried out at various conditions of
temperatures ranging from 278 to 338 K ± 2 K , concentrations,
processing time and a wide range of pH between 2.5-11. Adsorption
isotherm equations such as Freundlich, and Langmuir were applied to
calculate the values of respective constants. Adsorption study was
found that the currently introduced adsorbent can be used to remove
cationic dyes such as methylene blue from aqueous solutions.
Abstract: In today-s new technology era, cluster has become a
necessity for the modern computing and data applications since many
applications take more time (even days or months) for computation.
Although after parallelization, computation speeds up, still time
required for much application can be more. Thus, reliability of the
cluster becomes very important issue and implementation of fault
tolerant mechanism becomes essential. The difficulty in designing a
fault tolerant cluster system increases with the difficulties of various
failures. The most imperative obsession is that the algorithm, which
avoids a simple failure in a system, must tolerate the more severe
failures. In this paper, we implemented the theory of watchdog timer
in a parallel environment, to take care of failures. Implementation of
simple algorithm in our project helps us to take care of different
types of failures; consequently, we found that the reliability of this
cluster improves.
Abstract: With the fast evolution of digital data exchange, security information becomes much important in data storage and transmission. Due to the increasing use of images in industrial process, it is essential to protect the confidential image data from unauthorized access. In this paper, we analyze the Advanced Encryption Standard (AES), and we add a key stream generator (A5/1, W7) to AES to ensure improving the encryption performance; mainly for images characterised by reduced entropy. The implementation of both techniques has been realized for experimental purposes. Detailed results in terms of security analysis and implementation are given. Comparative study with traditional encryption algorithms is shown the superiority of the modified algorithm.