Abstract: Ovshinsky initiated scientific research in the field of
amorphous and disordered materials that continues to this day. The
Ovshinsky Effect where the resistance of thin GST films is
significantly reduced upon the application of low voltage is of
fundamental importance in phase-change - random access memory
(PC-RAM) devices.GST stands for GdSbTe chalcogenide type
glasses.However, the Ovshinsky Effect is not without controversy.
Ovshinsky thought the resistance of GST films is reduced by the
redistribution of charge carriers; whereas, others at that time including
many PC-RAM researchers today argue that the GST resistance
changes because the GST amorphous state is transformed to the
crystalline state by melting, the heat supplied by external heaters. In
this controversy, quantum mechanics (QM) asserts the heat capacity of
GST films vanishes, and therefore melting cannot occur as the heat
supplied cannot be conserved by an increase in GST film
temperature.By precluding melting, QM re-opens the controversy
between the melting and charge carrier mechanisms. Supporting
analysis is presented to show that instead of increasing GST film
temperature, conservation proceeds by the QED induced creation of
photons within the GST film, the QED photons confined by TIR. QED
stands for quantum electrodynamics and TIR for total internal
reflection. The TIR confinement of QED photons is enhanced by the
fact the absorbedheat energy absorbed in the GST film is concentrated
in the TIR mode because of their high surface to volume ratio. The
QED photons having Planck energy beyond the ultraviolet produce
excitons by the photoelectric effect, the electrons and holes of which
reduce the GST film resistance.
Abstract: A transient heat transfer mathematical model for the
prediction of temperature distribution in the car body during primer
baking has been developed by considering the thermal radiation and
convection in the furnace chamber and transient heat conduction
governing equations in the car framework. The car cockpit is
considered like a structure with six flat plates, four vertical plates
representing the car doors and the rear and front panels. The other
two flat plates are the car roof and floor. The transient heat
conduction in each flat plate is modeled by the lumped capacitance
method. Comparison with the experimental data shows that the heat
transfer model works well for the prediction of thermal behavior of
the car body in the curing furnace, with deviations below 5%.
Abstract: A study of electromagnetic flow meter is presented in the paper. Comparison has been made between the analytical and the numerical results by the use of FEM numerical analysis (Quick Field 5.6) for determining polarization voltage through the circle cross section of the polarization transducer. Exciting and geometrical parameters increasing its effectiveness has been examined. The aim is to obtain maximal output signal. The investigations include different variants of the magnetic flux density distribution around the tube: homogeneous field of magnitude Bm, linear distribution with maximal value Bm and trapezium distribution conserving the same exciting magnetic energy as the homogeneous field.
Abstract: The extract of milk thistle contains a mix of flavonolignans termed silymarine.. In order to analysis influence of growth regulators, genotype, explant and subculture on the accumulation of flavonolignans, a study was carried out by using two genotype (Budakalszi and Noor abad moghan cultivars), cotyledon and hypocotyle explants, solid media of MS supplemented by different combinations of two growth regulators; Kinetin (0.1, 1 mg/l) and 2,4-D (1, 2 mg/l). Seeds of the plant were germinated in MS media whitout growth regulators in growth chamber at 26°C and darkness condition. In order to callus induction, the culture media was supplemented whit different concentrations of 2,4-D and kinetin. Calli obtained from explants were sub-cultured four times into the fresh media of the first experiment. flavonoides was extracted from calli in four subcultures. The flavonoid components were determined by high- performance liquid choromatography (HPLC) and separated into Taxifolin, Silydianin+Silychristin, Silybin A+B and Isosilybin A+B. Results showed that with increasing callus age, increased accumulation of silybin A+B, but reduced Isosilybin A+B content. Highest accumulation of Taxifolin was observed at first calli. Calli produced from cotyledon explant of Budakalszi cultivar were superior for Silybin A+B, where calli from hypocotyl explant produced higher amount of Taxifolin and Silydianin+Silychristin. The best cultivar for Silymarin production in this study was Budakalszi cultivar. High amount of SBN A+B and TXF were obtained from hypocotil explant.
Abstract: Effect of high temperature exposure on properties of cement mortar containing municipal solid waste incineration (MSWI) bottom ash as partial natural aggregate replacement is analyzed in the paper. The measurements of mechanical properties, bulk density, matrix density, total open porosity, sorption and desorption isotherms are done on samples exposed to the temperatures of 20°C to 1000°C. TGA analysis is performed as well. Finally, the studied samples are analyzed by IR spectroscopy in order to evaluate TGA data.
Abstract: Utilizing echoic intension and distribution from different organs and local details of human body, ultrasonic image can catch important medical pathological changes, which unfortunately may be affected by ultrasonic speckle noise. A feature preserving ultrasonic image denoising and edge enhancement scheme is put forth, which includes two terms: anisotropic diffusion and edge enhancement, controlled by the optimum smoothing time. In this scheme, the anisotropic diffusion is governed by the local coordinate transformation and the first and the second order normal derivatives of the image, while the edge enhancement is done by the hyperbolic tangent function. Experiments on real ultrasonic images indicate effective preservation of edges, local details and ultrasonic echoic bright strips on denoising by our scheme.
Abstract: Global competitiveness has recently become the
biggest concern of both manufacturing and service companies.
Electronic commerce, as a key technology enables the firms to reach
all the potential consumers from all over the world. In this study, we
have presented commonly used electronic payment systems, and then
we have shown the evaluation of these systems in respect to different
criteria. The payment systems which are included in this research are
the credit card, the virtual credit card, the electronic money, the
mobile payment, the credit transfer and the debit instruments. We
have realized a systematic comparison of these systems in respect to
three main criteria: Technical, economical and social. We have
conducted a fuzzy multi-criteria decision making procedure to deal
with the multi-attribute nature of the problem. The subjectiveness
and imprecision of the evaluation process are modeled using
triangular fuzzy numbers.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: The problem of manipulator control is a highly
complex problem of controlling a system which is multi-input, multioutput,
non-linear and time variant. In this paper some adaptive
fuzzy, and a new hybrid fuzzy control algorithm have been
comparatively evaluated through simulations, for manipulator
control. The adaptive fuzzy controllers consist of self-organizing,
self-tuning, and coarse/fine adaptive fuzzy schemes. These
controllers are tested for different trajectories and for varying
manipulator parameters through simulations. Various performance
indices like the RMS error, steady state error and maximum error are
used for comparison. It is observed that the self-organizing fuzzy
controller gives the best performance. The proposed hybrid fuzzy
plus integral error controller also performs remarkably well, given its
simple structure.
Abstract: In this paper, we construct and implement a new
Steganography algorithm based on learning system to hide a large
amount of information into color BMP image. We have used adaptive
image filtering and adaptive non-uniform image segmentation with
bits replacement on the appropriate pixels. These pixels are selected
randomly rather than sequentially by using new concept defined by
main cases with sub cases for each byte in one pixel. According to
the steps of design, we have been concluded 16 main cases with their
sub cases that covere all aspects of the input information into color
bitmap image. High security layers have been proposed through four
layers of security to make it difficult to break the encryption of the
input information and confuse steganalysis too. Learning system has
been introduces at the fourth layer of security through neural
network. This layer is used to increase the difficulties of the statistical
attacks. Our results against statistical and visual attacks are discussed
before and after using the learning system and we make comparison
with the previous Steganography algorithm. We show that our
algorithm can embed efficiently a large amount of information that
has been reached to 75% of the image size (replace 18 bits for each
pixel as a maximum) with high quality of the output.
Abstract: Pentachlorophenol (PCP) is a polychlorinated
aromatic compound that is widespread in industrial effluents and is
considered to be a serious pollutant. Among the variety of industrial
effluents encountered, effluents from tanning industry are very
important and have a serious pollution potential. PCP is also formed
unintentionally in effluents of paper and pulp industries. It is highly
persistent in soils and is lethal to a wide variety of beneficial
microorganisms and insects, human beings and animals. The natural
processes that breakdown toxic chemicals in the environment have
become the focus of much attention to develop safe and environmentfriendly
deactivation technologies. Microbes and plants are among
the most important biological agents that remove and degrade waste
materials to enable their recycling in the environment. The present
investigation was carried out with the aim of developing a microbial
system for bioremediation of PCP polluted soils. A number of plant
species were evaluated for their ability to tolerate different
concentrations of pentachlorophenol (PCP) in the soil. The
experiment was conducted for 30 days under pot culture conditions.
The toxic effect of PCP on plants was studied by monitoring seed
germination, plant growth and biomass. As the concentration of PCP
was increased to 50 ppm, the inhibition of seed germination, plant
growth and biomass was also increased. Although PCP had a
negative effect on all plant species tested, maize and groundnut
showed the maximum tolerance to PCP. Other tolerating crops
included wheat, safflower, sunflower, and soybean. From the
rhizosphere soil of the tolerant seedlings, as many as twenty seven
PCP tolerant bacteria were isolated. From soybean, 8; sunflower, 3;
safflower 8; maize 2; groundnut and wheat, 3 each isolates were
made. They were screened for their PCP degradation potentials.
HPLC analyses of PCP degradation revealed that the isolate MAZ-2
degraded PCP completely. The isolate MAZ-1 was the next best
isolate with 90 per cent PCP degradation. These strains hold promise
to be used in the bioremediation of PCP polluted soils.
Abstract: For gamma radiation detection, assemblies having
scintillation crystals and a photomultiplier tube, also there is a
preamplifier connected to the detector because the signals from
photomultiplier tube are of small amplitude. After pre-amplification
the signals are sent to the amplifier and then to the multichannel
analyser. The multichannel analyser sorts all incoming electrical
signals according to their amplitudes and sorts the detected photons
in channels covering small energy intervals. The energy range of
each channel depends on the gain settings of the multichannel
analyser and the high voltage across the photomultiplier tube. The
exit spectrum data of the two main isotopes studied ,putting data in
biomass program ,process it by Matlab program to get the solid
holdup image (solid spherical nuclear fuel)
Abstract: Chicken feathers were used as biosorbent for Pb
removal from aqueous solution. In this paper, the kinetics and
equilibrium studies at several pH, temperature, and metal
concentration values are reported. For tested conditions, the Pb
sorption capacity of this poultry waste ranged from 0.8 to 8.3 mg/g.
Optimal conditions for Pb removal by chicken feathers have been
identified. Pseudo-first order and pseudo-second order equations
were used to analyze the experimental data. In addition, the sorption
isotherms were fitted to classical Langmuir and Freundlich models.
Finally, thermodynamic parameters for the sorption process have
been determined. In summary, the results showed that chicken
feathers are an alternative and promising sorbent for the treatment of
effluents polluted by Pb ions.
Abstract: The aim of the study was to investigate whether there
is the promotion of product ecodesign measures as a result of
adopting ISO 14001 certification in manufacturing companies in the
Republic of Slovenia. Companies gave the most of their product
development attention to waste and energy reduction during
manufacturing process and reduction of material consumption per
unit of product. Regarding the importance of different ecodesign
criteria reduction of material consumption per unit of product was
reported as the most important criterion. Less attention is paid to endof-
life issues considering recycling or packaging. Most
manufacturing enterprises considered ISO 14001 standard as a very
useful tool or at least a useful tool helping them to accelerate and
establish product ecodesign activities. Two most frequently
considered ecodesign drivers are increased competitive advantage
and legal requirements and two most important barriers are high
development costs and insufficient market demand.
Abstract: Moulded parts contribute to more than 70% of
components in products. However, common defects particularly in
plastic injection moulding exist such as: warpage, shrinkage, sink
marks, and weld lines. In this paper Taguchi experimental design
methods are applied to reduce the warpage defect of thin plate
Acrylonitrile Butadiene Styrene (ABS) and are demonstrated in two
levels; namely, orthogonal arrays of Taguchi and the Analysis of
Variance (ANOVA). Eight trials have been run in which the optimal
parameters that can minimize the warpage defect in factorial
experiment are obtained. The results obtained from ANOVA
approach analysis with respect to those derived from MINITAB
illustrate the most significant factors which may cause warpage in
injection moulding process. Moreover, ANOVA approach in
comparison with other approaches like S/N ratio is more accurate and
with the interaction of factors it is possible to achieve higher and the
better outcomes.
Abstract: The paper presents the influence of the conventional
ploughing tillage technology in comparison with the minimum
tillage, upon the soil properties, weed control and yield in the case of
maize (Zea mays L.), soya-bean (Glycine hispida L.) and winter
wheat (Triticum aestivum L.) in a three years crop rotation. A
research has been conducted at the University of Agricultural
Sciences and Veterinary Medicine Cluj-Napoca, Romania. The use of
minimum soil tillage systems within a three years rotation: maize,
soya-bean, wheat favorites the rise of the aggregates hydro stability
with 5.6-7.5% on a 0-20 cm depth and 5-11% on 20-30 cm depth.
The minimum soil tillage systems – paraplow, chisel or rotary grape
– are polyvalent alternatives for basic preparation, germination bed
preparation and sowing, for fields and crops with moderate loose
requirements being optimized technologies for: soil natural fertility
activation and rationalization, reduction of erosion, increasing the
accumulation capacity for water and realization of sowing in the
optimal period. The soil tillage system influences the productivity
elements of cultivated species and finally the productions thus
obtained. Thus, related to conventional working system, the
productions registered in minimum tillage working represented 89-
97% in maize, 103-112% in soya-bean, 93-99% in winter-wheat. The
results of investigations showed that the yield is a conclusion soil
tillage systems influence on soil properties, plant density assurance
and on weed control. Under minimum tillage systems in the case of
winter weat as an option for replacing classic ploughing, the best
results in terms of quality indices were obtained from version worked
with paraplow, followed by rotary harrow and chisel. At variants
worked with paraplow were obtained quality indices close to those of
the variant worked with plow, and protein and gluten content was
even higher. At Ariesan variety, highest protein content, 12.50% and
gluten, 28.6% was obtained for the variant paraplow.
Abstract: Let T,U and V be rings with identity and M be a unitary (T,U)-bimodule, N be a unitary (U, V )- bimodule, D be a unitary (T, V )-bimodule . We characterize homomorphisms and isomorphisms of the generalized matrix ring Γ = T M D 0 U N 0 0 V .
Abstract: In the present work we investigate both the elastic and
electric properties of a chiral material. We consider a composite
structure made from a polymer matrix and anisotropic inclusions of
GaAs taking into account piezoelectric and dielectric properties of
the composite material. The principal task of the work is the
estimation of the functional properties of the composite material.
Abstract: This paper presents a critical study about the
application of Neural Networks to ion-exchange process. Ionexchange
is a complex non-linear process involving many factors
influencing the ions uptake mechanisms from the pregnant solution.
The following step includes the elution. Published data presents
empirical isotherm equations with definite shortcomings resulting in
unreliable predictions. Although Neural Network simulation
technique encounters a number of disadvantages including its “black
box", and a limited ability to explicitly identify possible causal
relationships, it has the advantage to implicitly handle complex
nonlinear relationships between dependent and independent
variables. In the present paper, the Neural Network model based on
the back-propagation algorithm Levenberg-Marquardt was developed
using a three layer approach with a tangent sigmoid transfer function
(tansig) at hidden layer with 11 neurons and linear transfer function
(purelin) at out layer. The above mentioned approach has been used
to test the effectiveness in simulating ion exchange processes. The
modeling results showed that there is an excellent agreement between
the experimental data and the predicted values of copper ions
removed from aqueous solutions.
Abstract: With deep development of software reuse, componentrelated
technologies have been widely applied in the development of
large-scale complex applications. Component identification (CI) is
one of the primary research problems in software reuse, by analyzing
domain business models to get a set of business components with high
reuse value and good reuse performance to support effective reuse.
Based on the concept and classification of CI, its technical stack is
briefly discussed from four views, i.e., form of input business models,
identification goals, identification strategies, and identification
process. Then various CI methods presented in literatures are
classified into four types, i.e., domain analysis based methods,
cohesion-coupling based clustering methods, CRUD matrix based
methods, and other methods, with the comparisons between these
methods for their advantages and disadvantages. Additionally, some
insufficiencies of study on CI are discussed, and the causes are
explained subsequently. Finally, it is concluded with some
significantly promising tendency about research on this problem.