Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: This study aims to investigate the mixing behaviors of
deionized (DI) water and carboxymethyl cellulose (CMC) solutions in
C-shaped serpentine micromixers over a wide range of flow
conditions. The flow of CMC solutions exhibits shear-thinning
behaviors. Numerical simulations are performed to investigate the
effects of the mean flow speed, fluid properties and geometry
parameters on flow and mixing in the micromixers with the serpentine
channel of the same overall channel length. From the results, we can
find the following trends. When convection dominates fluid mixing,
the curvature-induced vortices enhance fluid mixing effectively. The
mixing efficiency of a micromixer consisting of semicircular C-shaped
repeating units with a smaller centerline radius is better than that of a
micromixer consisting of major segment repeating units with a larger
centerline radius. The viscosity of DI water is less than the overall
average apparent viscosity of CMC solutions, and so the effect of
curvature-induced vortices on fluid mixing in DI water is larger than
that in CMC solutions for the cases with the same mean flow speed.
Abstract: Because current wireless communication requires high
reliability in a limited bandwidth environment, this paper proposes
the variable modulation scheme based on the codebook. The variable
modulation scheme adjusts transmission power using the codebook in
accordance with channel state. Also, if the codebook is composed of
many bits, the reliability is more improved by the proposed scheme.
The simulation results show that the performance of proposed scheme
has better reliability than the the performance of conventional scheme.
Abstract: This study analyzes the critical gaps in the
architecture of European stability and the expected role of the
banking union as the new important step towards completing the
Economic and Monetary Union that should enable the creation of
safe and sound financial sector for the euro area market. The single
rulebook together with the Single Supervisory Mechanism and the
Single Resolution Mechanism - as two main pillars of the banking
union, should provide a consistent application of common rules and
administrative standards for supervision, recovery and resolution of
banks – with the final aim of replacing the former bail-out practice
with the bail-in system through which possible future bank failures
would be resolved by their own funds, i.e. with minimal costs for
taxpayers and real economy. In this way, the vicious circle between
banks and sovereigns would be broken. It would also reduce the
financial fragmentation recorded in the years of crisis as the result of
divergent behaviors in risk premium, lending activities and interest
rates between the core and the periphery. In addition, it should
strengthen the effectiveness of monetary transmission channels, in
particular the credit channels and overflows of liquidity on the money
market which, due to the fragmentation of the common financial
market, has been significantly disabled in period of crisis. However,
contrary to all the positive expectations related to the future
functioning of the banking union, major findings of this study
indicate that characteristics of the economic system in which the
banking union will operate should not be ignored. The euro area is an
integration of strong and weak entities with large differences in
economic development, wealth, assets of banking systems, growth
rates and accountability of fiscal policy. The analysis indicates that
low and unbalanced economic growth remains a challenge for the
maintenance of financial stability and this problem cannot be
resolved just by a single supervision. In many countries bank assets
exceed their GDP by several times and large banks are still a matter
of concern, because of their systemic importance for individual
countries and the euro zone as a whole. The creation of the Single
Supervisory Mechanism and the Single Resolution Mechanism is a
response to the European crisis, which has particularly affected
peripheral countries and caused the associated loop between the
banking crisis and the sovereign debt crisis, but has also influenced
banks’ balance sheets in the core countries, as the result of crossborder
capital flows. The creation of the SSM and the SRM should
prevent the similar episodes to happen again and should also provide
a new opportunity for strengthening of economic and financial
systems of the peripheral countries. On the other hand, there is a
potential threat that future focus of the ECB, resolution mechanism
and other relevant institutions will be extremely oriented towards
large and significant banks (whereby one half of them operate in the
core and most important euro area countries), and therefore it remains
questionable to what extent will the common resolution funds will be used for rescue of less important institutions. Recent geopolitical
developments will be the optimal indicator to show whether the
previously established mechanisms are sufficient enough to maintain
the adequate financial stability in the euro area market.
Abstract: Particle size distribution, the most important
characteristics of aerosols, is obtained through electrical
characterization techniques. The dynamics of charged nanoparticles
under the influence of electric field in Electrical Mobility
Spectrometer (EMS) reveals the size distribution of these particles.
The accuracy of this measurement is influenced by flow conditions,
geometry, electric field and particle charging process, therefore by
the transfer function (transfer matrix) of the instrument. In this work,
a wire-cylinder corona charger was designed and the combined fielddiffusion
charging process of injected poly-disperse aerosol particles
was numerically simulated as a prerequisite for the study of a
multichannel EMS. The result, a cloud of particles with no uniform
charge distribution, was introduced to the EMS. The flow pattern and
electric field in the EMS were simulated using Computational Fluid
Dynamics (CFD) to obtain particle trajectories in the device and
therefore to calculate the reported signal by each electrometer.
According to the output signals (resulted from bombardment of
particles and transferring their charges as currents), we proposed a
modification to the size of detecting rings (which are connected to
electrometers) in order to evaluate particle size distributions more
accurately. Based on the capability of the system to transfer
information contents about size distribution of the injected particles,
we proposed a benchmark for the assessment of optimality of the
design. This method applies the concept of Von Neumann entropy
and borrows the definition of entropy from information theory
(Shannon entropy) to measure optimality. Entropy, according to the
Shannon entropy, is the ''average amount of information contained in
an event, sample or character extracted from a data stream''.
Evaluating the responses (signals) which were obtained via various
configurations of detecting rings, the best configuration which gave
the best predictions about the size distributions of injected particles,
was the modified configuration. It was also the one that had the
maximum amount of entropy. A reasonable consistency was also
observed between the accuracy of the predictions and the entropy
content of each configuration. In this method, entropy is extracted
from the transfer matrix of the instrument for each configuration.
Ultimately, various clouds of particles were introduced to the
simulations and predicted size distributions were compared to the
exact size distributions.
Abstract: A robust sequential nonparametric method is proposed
for adaptation to background noise parameters for real-time. The
distribution of background noise was modelled like to Huber
contamination mixture. The method is designed to operate as an
adaptation-unit, which is included inside a detection subsystem of an
integrated multichannel monitoring system. The proposed method
guarantees the given size of a nonasymptotic confidence set for noise
parameters. Properties of the suggested method are rigorously
proved. The proposed algorithm has been successfully tested in real
conditions of a functioning C-OTDR monitoring system, which was
designed to monitor railways.
Abstract: In this paper, we consider a cognitive relay network
(CRN) in which the primary receiver (PR) is protected by peak
transmit power ¯PST and/or peak interference power Q constraints.
In addition, the interference effect from the primary transmitter (PT)
is considered to show its impact on the performance of the CRN. We
investigate the outage probability (OP) and outage capacity (OC) of
the CRN by deriving closed-form expressions over Rayleigh fading
channel. Results show that both the OP and OC improve by increasing
the cooperative relay nodes as well as when the PT is far away from
the SR.
Abstract: In the cooperative transmission scheme, both the
cellular system and broadcasting system are composed. Two cellular
base stations (CBSs) communicating with a user in the cell edge use
cooperative transmission scheme in the conventional scheme. In the
case that the distance between two CBSs and the user is distant, the
conventional scheme does not guarantee the quality of the
communication because the channel condition is bad. Therefore, if the
distance between CBSs and a user is distant, the performance of the
conventional scheme is decreased. Also, the bad channel condition has
bad effects on the performance. The proposed scheme uses two relays
to communicate well with CBSs when the channel condition between
CBSs and the user is poor. Using the relay in the high attenuation
environment can obtain both advantages of the high bit error rate
(BER) and throughput performance.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: Neural activity in the human brain starts from the
early stages of prenatal development. This activity or signals
generated by the brain are electrical in nature and represent not only
the brain function but also the status of the whole body. At the
present moment, three methods can record functional and
physiological changes within the brain with high temporal resolution
of neuronal interactions at the network level: the
electroencephalogram (EEG), the magnet oencephalogram (MEG),
and functional magnetic resonance imaging (fMRI); each of these has
advantages and shortcomings. EEG recording with a large number of
electrodes is now feasible in clinical practice. Multichannel EEG
recorded from the scalp surface provides very valuable but indirect
information about the source distribution. However, deep electrode
measurements yield more reliable information about the source
locations intracranial recordings and scalp EEG are used with the
source imaging techniques to determine the locations and strengths of
the epileptic activity. As a source localization method, Low
Resolution Electro-Magnetic Tomography (LORETA) is solved for
the realistic geometry based on both forward methods, the Boundary
Element Method (BEM) and the Finite Difference Method (FDM). In
this paper, we review the findings EEG- LORETA about epilepsy.
Abstract: In this paper, improved performance scheme for
joint transmission (JT) is proposed in downlink (DL) coordinated
multi-point (CoMP) in case of the constraint transmission power.
This scheme is that a serving transmission point (TP) requests the
JT to an inter-TP and it selects a precoding technique according
to the channel state information (CSI) from user equipment (UE).
The simulation results show that the bit error rate (BER) and the
throughput performances of the proposed scheme provide the high
spectral efficiency and the reliable data at the cell edge.
Abstract: Effect of sprue/metal head height on mould filling,
microstructure and mechanical properties of TWDI casting is studied.
Results show that metal/sprue height of 50 mm is not sufficient to
push the melt through the gating channel, but as it is increased from
100-350 mm, proper mould filling is achieved. However at higher
heights between 200 mm and 350 mm, defects associated with
incomplete solidification, carbide precipitation and turbulent flow are
evident. This research shows that superior UTS, hardness, nodularity
and nodule count are obtained at 100 mm sprue height.
Abstract: This work consists of a numerical simulation of
convective heat transfer in a vertical plane channel filled with a heat
generating porous medium, in the absence of local thermal
equilibrium. The walls are maintained to a constant temperature and
the inlet velocity is uniform. The dynamic range is described by the
Darcy-Brinkman model and the thermal field by two energy
equations model. A dimensionless formulation is developed for
performing a parametric study based on certain dimensionless groups
such as, the Biot interstitial number, the thermal conductivity ratio
and the volumetric heat generation, q '''. The governing equations are
solved using the finite volume method, gave rise to a multitude of
results concerning in particular the thermal field in the porous
channel and the existence or not of the local thermal equilibrium.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: This paper presents Carrier Sense Multiple Access
(CSMA) communication models based on SoC design methodology.
Such a model can be used to support the modeling of the complex
wireless communication systems. Therefore, the use of such
communication model is an important technique in the construction
of high-performance communication. SystemC has been chosen
because it provides a homogeneous design flow for complex designs
(i.e. SoC and IP-based design). We use a swarm system to validate
CSMA designed model and to show how advantages of incorporating
communication early in the design process. The wireless
communication created through the modeling of CSMA protocol that
can be used to achieve communication between all the agents and to
coordinate access to the shared medium (channel).
Abstract: This paper presents a computational study of steady
state three dimensional very high turbulent flow and heat transfer
characteristics in a constant temperature-surfaced circular duct fitted
with 900 hemispherical inline baffles. The computations are based on
realizable k-ɛ model with standard wall function considering the
finite volume method, and the SIMPLE algorithm has been
implemented. Computational Study are carried out for Reynolds
number, Re ranging from 80000 to 120000, Prandtl Number, Pr of
0.73, Pitch Ratios, PR of 1,2,3,4,5 based on the hydraulic diameter of
the channel, hydrodynamic entry length, thermal entry length and the
test section. Ansys Fluent 15.0 software has been used to solve the
flow field. Study reveals that circular pipe having baffles has a higher
Nusselt number and friction factor compared to the smooth circular
pipe without baffles. Maximum Nusselt number and friction factor
are obtained for the PR=5 and PR=1 respectively. Nusselt number
increases while pitch ratio increases in the range of study; however,
friction factor also decreases up to PR 3 and after which it becomes
almost constant up to PR 5. Thermal enhancement factor increases
with increasing pitch ratio but with slightly decreasing Reynolds
number in the range of study and becomes almost constant at higher
Reynolds number. The computational results reveal that optimum
thermal enhancement factor of 900 inline hemispherical baffle is
about 1.23 for pitch ratio 5 at Reynolds number 120000.It also shows
that the optimum pitch ratio for which the baffles can be installed in
such very high turbulent flows should be 5. Results show that pitch
ratio and Reynolds number play an important role on both fluid flow
and heat transfer characteristics.
Abstract: In this work, the Ictalurus punctatus species estimated
available physical habitat is compared with the estimated physical
habitat for the same but modified river reach, with the aim of creating
a linear park, along a length of 5 500 m.
To determine the effect of ecological park construction, on
physical habitat of the Lerma river stretch of study, first, the available
habitat for the Ictalurus punctatus species was estimated through the
simulation of the physical habitat, by using surveying, hydraulics,
and habitat information gotten at the river reach in its actual situation.
Second, it was estimated the available habitat for the above species,
upon the simulation of the physical habitat through the proposed
modification for the ecological park creation. Third, it is presented a
comparison between both scenarios in terms of available habitat
estimated for Ictalurus punctatus species, concluding that in cases of
adult and spawning life stages, changes in the channel to create an
ecological park would produce a considerable loss of potentially
usable habitat (PUH), while in the case of the juvenile life stage PUH
remains virtually unchanged, and in the case of life stage fry the PUH
would increase due to the presence of velocities and depths of lesser
magnitude, due to the presence of minor flow rates and lower volume
of the wet channel.
It is expected that habitat modification for linear park construction
may produce the lack of Ictalurus punktatus species conservation at
the river reach of the study.
Abstract: Any signal transmitted over a channel is corrupted by noise and interference. A host of channel coding techniques has been proposed to alleviate the effect of such noise and interference. Among these Turbo codes are recommended, because of increased capacity at higher transmission rates and superior performance over convolutional codes. The multimedia elements which are associated with ample amount of data are best protected by Turbo codes. Turbo decoder employs Maximum A-posteriori Probability (MAP) and Soft Output Viterbi Decoding (SOVA) algorithms. Conventional Turbo coded systems employ Equal Error Protection (EEP) in which the protection of all the data in an information message is uniform. Some applications involve Unequal Error Protection (UEP) in which the level of protection is higher for important information bits than that of other bits. In this work, enhancement to the traditional Log MAP decoding algorithm is being done by using optimized scaling factors for both the decoders. The error correcting performance in presence of UEP in Additive White Gaussian Noise channel (AWGN) and Rayleigh fading are analyzed for the transmission of image with Discrete Cosine Transform (DCT) as source coding technique. This paper compares the performance of log MAP, Modified log MAP (MlogMAP) and Enhanced log MAP (ElogMAP) algorithms used for image transmission. The MlogMAP algorithm is found to be best for lower Eb/N0 values but for higher Eb/N0 ElogMAP performs better with optimized scaling factors. The performance comparison of AWGN with fading channel indicates the robustness of the proposed algorithm. According to the performance of three different message classes, class3 would be more protected than other two classes. From the performance analysis, it is observed that ElogMAP algorithm with UEP is best for transmission of an image compared to Log MAP and MlogMAP decoding algorithms.
Abstract: The main function of Medium Access Control (MAC) is to share the channel efficiently between all nodes. In the real-time scenario, there will be certain amount of wastage in bandwidth due to back-off periods. More bandwidth will be wasted in idle state if the back-off period is very high and collision may occur if the back-off period is small. So, an optimization is needed for this problem. The main objective of the work is to reduce delay due to back-off period thereby reducing collision and increasing throughput. Here a method, called the virtual back-off algorithm (VBA) is used to optimize the back-off period and thereby it increases throughput and reduces collisions. The main idea is to optimize the number of transmission for every node. A counter is introduced at each node to implement this idea. Here counter value represents the sequence number. VBA is classified into two types VBA with counter sharing (VBA-CS) and VBA with no counter sharing (VBA-NCS). These two classifications of VBA are compared for various parameters. Simulation is done in NS-2 environment. The results obtained are found to be promising.
Abstract: There is not much effective guideline on development of design parameters selection on spring back for advanced high strength steel sheet metal in U-channel process during cold forming process. This paper presents the development of predictive model for spring back in U-channel process on advanced high strength steel sheet employing Response Surface Methodology (RSM). The experimental was performed on dual phase steel sheet, DP590 in Uchannel forming process while design of experiment (DoE) approach was used to investigates the effects of four factors namely blank holder force (BHF), clearance (C) and punch travel (Tp) and rolling direction (R) were used as input parameters using two level values by applying Full Factorial design (24 ). From a statistical analysis of variant (ANOVA), result showed that blank holder force (BHF), clearance (C) and punch travel (Tp) displayed significant effect on spring back of flange angle (β2 ) and wall opening angle (β1 ), while rolling direction (R) factor is insignificant. The significant parameters are optimized in order to reduce the spring back behavior using Central Composite Design (CCD) in RSM and the optimum parameters were determined. A regression model for spring back was developed. The effect of individual parameters and their response was also evaluated. The results obtained from optimum model are in agreement with the experimental values.