Abstract: In order to study the influence of different methods of controlling weeds such as mechanical weeding and mechanical weeder efficiency analysis in mechanical cultivation conditions, in farming year of 2011 an experiment was done in a farm in coupling and development of technology center in Haraz,Iran. The treatments consisted of (I) control treatment: where no weeding was done, (II) use of mechanical weeding without engine and (III) power mechanical weeding. Results showed that experimental treatments had significantly different effects (p=0.05) on yield traits and number of filled grains per panicle, while treatments had the significant effects on grain weight and dry weight of weeds in the first, second and third weeding methods at 1% of confidence level. Treatment (II) had its most significant effect on number of filled grains per panicle and yield performance standpoint, which was 3705.97 kg ha-1 in its highest peak. Treatment (III) was ranked as second influential with 3559.8 kg ha-1. In addition, under (I) treatments, 2364.73 kg ha-1 of yield produced. The minimum dry weights of weeds in all weeding methods were related to the treatment (II), (III) and (I), respectively. The correlation coefficient analysis showed that total yield had a significant positive correlation with the panicle grain yield per plant (r= 0.55*) and the number of grains per panicle-1 (r= 0.57*) and the number of filled grains (r= 0.63*). Total rice yield also had negative correlation of r= -0. 64* with weed dry weight at second weed sampling time (17 DAT). The weed dry weight at third and fourth sampling times (24 and 40 DAT) had negative correlations of -0.65** and r=-0.61* with rice yield, respectively.
Abstract: Based on the field investigation and long term remote
sensing data, the dynamics of the alpine wetland in the river basin and
their response to climate change were studied. Results showed the
alpine wetlands accounted for 3.73% of total basin in 2010. Lake and
river appeared an increasing trend in the past 30 years, with an
increase of 34.36 % and 24.57%. However, swamp exhibited a
tendency of decreasing with 233.74 km2. Annual average temperature,
maximum temperature, minimum temperature and precipitation in the
river basin all exhibited an increasing trend, whereas relative humidity
exhibited a decreasing trend. Ice and snow melting are main reasons of
lake and river area enhancement and swamp area descend. There
existed 91.78%-97.86% of reduced swamp converted into lakes on the
basis of remote sensing image interpretation. China-s government
policy of implementing development in the river basin is the major
driving force of artificial wetland growth.
Abstract: Pleurotus ostreatus is a common edible mushroom with a number of properties that can help to solve the nutritional and economical problems of people in Chiapas, Mexico. The objective of this project was to produce the mushroom under a sustainable management in which only regional products were allowed as a way to promote the cultivation and consumption of Pleurotus ostreatus; 5 different substrates were tested as well as 2 sanitation methods. The obtained results showed that the highest yields were obtained using corn husk and a thermal sanitation method. Pests and diseases were not a problem during the project but they appeared more in the substrates sanitized with calcium hydroxide.
Abstract: Paddy being cultivated since about 10,000 years B.C in Ganga Valley in India, its production reached up to 99 million tons in the year 2012. BGA are of much ecological importance for maintaining the soil fertility and reclaiming the alkalinity. In present investigation attempts were made to identify the local cyanobacterial genera from the paddy fields, BGA application for green farming enabling the paddy to utilize more amount of nitrogen released and to examine its impact along with Urea upon growth and yield responses of the Paddy crop. It was observed that combined treatment of BGA with Urea proved better response in almost all growth parameters and yield attributes except number of tillers/ Plant and grains/ panicle as compared to application of either Urea or BGA alone. The Paddy growers should be encouraged to adopt BGA along with Urea as source of Nitrogen for Paddy cultivation.
Abstract: In a field experiment, growth parameters of soybean
cultivars in different weeding regimes was investigated. The trial was
split plot in a randomized complete block design. The four cultivars
and two lines of soybean (Glycine max L.) including: Sahar, Hill,
Sari, Telar, 032 and 033 in main plot and weeding regime consist of
no weeding (control), one weeding (35 days after planting) and two
weeding (35+20 days after planting) were randomized in sub plot.
The results showed that during the growth season 033 had the highest
dry matter in two weeding. In two weeding regime the dry matter
decreased. ). In all weeding regimes 033 had the highest CGR (Figs.
3a, 3b and 3c), which cleared this cultivar ability compare to the
others. This cultivar by increasing its leaf area could do more
photosynthesis, so, have a higher CGR.
Abstract: Decision support systems are usually based on
multidimensional structures which use the concept of hypercube.
Dimensions are the axes on which facts are analyzed and form a
space where a fact is located by a set of coordinates at the
intersections of members of dimensions. Conventional
multidimensional structures deal with discrete facts linked to discrete
dimensions. However, when dealing with natural continuous
phenomena the discrete representation is not adequate. There is a
need to integrate spatiotemporal continuity within multidimensional
structures to enable analysis and exploration of continuous field data.
Research issues that lead to the integration of spatiotemporal
continuity in multidimensional structures are numerous. In this paper,
we discuss research issues related to the integration of continuity in
multidimensional structures, present briefly a multidimensional
model for continuous field data. We also define new aggregation
operations. The model and the associated operations and measures
are validated by a prototype.
Abstract: This paper proposed a new CAD tools for microwave amplifier design. The proposed tool is based on survey about the broadband amplifier design methods, such as the Feedback amplifiers, balanced amplifiers and Compensated Matching Network The proposed tool is developed for broadband amplifier using a compensated matching network "unconditional stability amplifier". The developed program is based on analytical procedures with ability of smith chart explanation. The C# software is used for the proposed tools implementation. The program is applied on broadband amplifier as an example for testing. The designed amplifier is considered as a broadband amplifier at the range 300-700 MHz. The results are highly agreement with the expected results. Finally, these methods can be extended for wide band amplifier design.
Abstract: Nitrogen loss from irrigated cropland, particularly
sandy soils, significantly contributes to nitrate (NO3
-) levels in
surface and groundwaters. Thus, it is of great interest to use
inexpensive natural products that can increase the fertilizer efficiency
and decrease nitrate leaching. In this study, the ability of natural
Iranian zeolite clinoptilolite (Cp) and surfactant modified zeolite
clinoptilolite (SMZ) to remove NH4
+ and NO3
-, respectively, from
aqueous solutions was determined. The feasibility of using Cp and
SMZ as soil amendment to reduce nitrate leaching from soil using
lysimeters was also investigated. Zeolite showed 10.23% to 88.42%
NH4
+ removal efficiency over a wide range of initial NH4
+
concentrations. Nitrate removal efficiency by SMZ was 32.26% to
82.26%. Field study results showed that Cp and SMZ significantly (p
< 0.05) reduced leachate NO3-N concentration compared to control.
There was no significant difference between maximum and mean
leachate NO3-N concentration of SMZ lysimeters and those of Cp
lysimeters.
Abstract: In the present research, the titanium-catalyzed
ethylene dimerization and more specifically, the concomitant byproducts
and polymer formation have been studied in the presence of 2,5-dimethoxytetrahydrofuran as an electron donor compound in the
combination with triethylaluminium (TEA) as activator. Then, we
added ethylene chlorobromide as a new efficient promoter to the
relevant catalyst system. Finally, the behavior of novel homogeneous
[Titanium tetrabutoxide (Ti(OC4H9)4)/2,5-dimethoxytetrahydrofuran/
TEA/ethylene chlorobromide] was investigated in the various
operating conditions for the optimum production of 1-butene. In the
optimum conditions, a very high ethylene conversion (almost 90.77
%), a relative high selectivity to 1-butene (79.00 %), yield of reaction equal to 71.70 % and a significant productivity (turnover frequency
equal to 1370 h-1) were achieved.
Abstract: Carriers scattering in the inversion channel of n-
MOSFET dominates the drain current. This paper presents an effective
electron mobility model for the pocket implanted nano scale
n-MOSFET. The model is developed by using two linear pocket
profiles at the source and drain edges. The channel is divided into
three regions at source, drain and central part of the channel region.
The total number of inversion layer charges is found for these three
regions by numerical integration from source to drain ends and the
number of depletion layer charges is found by using the effective
doping concentration including pocket doping effects. These two
charges are then used to find the effective normal electric field,
which is used to find the effective mobility model incorporating the
three scattering mechanisms, such as, Coulomb, phonon and surface
roughness scatterings as well as the ballistic phenomena for the
pocket implanted nano-scale n-MOSFET. The simulation results show
that the derived mobility model produces the same results as found
in the literatures.
Abstract: A pilot plant for continuous flow microwave-assisted
chemical reaction combined with microreactors was developed and
water heating tests were conducted for evaluation of the developed
plant. We developed a microwave apparatus having a single
microwave generator that can heat reaction solutions in four reaction
fields simultaneously in order to increase throughput. We also
designed a four-branch waveguide using electromagnetic simulation,
and found that the transmission efficiency at 99%. Finally, we
developed the pilot plant using the developed microwave apparatus
and conducted water heating tests. The temperatures in the respective
reaction fields were controlled within ±1.1 K at 353.2 K. Moreover,
the energy absorption rates by the water were about 90% in the
respective reaction fields, whereas the energy absorption rate was
about 40% when 100 cm3 of water was heated by a commercially
available multimode microwave chemical reactor.
Abstract: An experimental study is presented on the effect of
Conservation Agriculture (CA) compared to Conventional
Agriculture (ConvA) upon Maize Yield based on split-plot model.
Two factors have been considered: A Factor-Fertilization with two
variants: A1- N40P40 kg/ha and A2- N90P70 kg/ha; B Factor- Crop
protection with 4 variants : B1- 4 treatments, B2-3 treatments, B3- 2
treatments and B4- 1 treatment. In comparison with conventional
agriculture, CA determined lower maize yields. Fertilization is the
key factor determining a yield gain of 973.58 kg/ha in ConvA and
1,123.33 kg/ha in CA. A reduced number of treatments determined a
yield decline. The A-B interaction had a positive effect on maize
yield when a larger amount of fertilizer and 4 or 3 treatments were
applied in ConvA and a benefic in CA for highest fertilization level
and 2 treatments. The B2A2 ConvA variant was the most efficient
leading to 302.67 kg/ha gain while B3A2 CA variant brought 181.33
kg production gain.
Abstract: The flow field within the combustor of scramjet
engine is very complex and poses a considerable challenge in the
design and development of a supersonic combustor with an optimized
geometry. In this paper comprehensive numerical studies on flow
field characteristics of different cavity based scramjet combustors
with transverse injection of hydrogen have been carried out for both
non-reacting and reacting flows. The numerical studies have been
carried out using a validated 2D unsteady, density based 1st-order
implicit k-omega turbulence model with multi-component finite rate
reacting species. The results show a wide variety of flow features
resulting from the interactions between the injector flows, shock
waves, boundary layers, and cavity flows. We conjectured that an
optimized cavity is a good choice to stabilize the flame in the
hypersonic flow, and it generates a recirculation zone in the scramjet
combustor. We comprehended that the cavity based scramjet
combustors having a bearing on the source of disturbance for the
transverse jet oscillation, fuel/air mixing enhancement, and flameholding
improvement. We concluded that cavity shape with
backward facing step and 45o forward ramp is a good choice to get
higher temperatures at the exit compared to other four models of
scramjet combustors considered in this study.
Abstract: This paper deals with the project selection problem. Project selection problem is one of the problems arose firstly in the field of operations research following some production concepts from primary product mix problem. Afterward, introduction of managerial considerations into the project selection problem have emerged qualitative factors and criteria to be regarded as well as quantitative ones. To overcome both kinds of criteria, an analytic network process is developed in this paper enhanced with fuzzy sets theory to tackle the vagueness of experts- comments to evaluate the alternatives. Additionally, a modified version of Least-Square method through a non-linear programming model is augmented to the developed group decision making structure in order to elicit the final weights from comparison matrices. Finally, a case study is considered by which developed structure in this paper is validated. Moreover, a sensitivity analysis is performed to validate the response of the model with respect to the condition alteration.
Abstract: Many studies have applied the Theory of Planned
Behavior (TPB) in predicting health behaviors among unique
populations. However, a new paradigm is emerging where focus is
now directed to modification and expansion of the TPB model rather
than utilization of the traditional theory. This review proposes new
models modified from the Theory of Planned Behavior and suggest
an appropriate study design that can be used to test the models within
physical activity and dietary practice domains among Type 2
diabetics in Kenya. The review was conducted by means of literature
search in the field of nutrition behavior, health psychology and
mixed methods using predetermined key words. The results identify
pre-intention and post intention gaps within the TPB model that need
to be filled. Additional psychosocial factors are proposed to be
included in the TPB model to generate new models and the efficacy
of these models tested using mixed methods design.
Abstract: Composite laminates are relatively weak in out of
plane loading, inter-laminar stress, stress concentration near the edge
and stress singularities. This paper develops a new analytical
formulation for laminated composite rotating disc fabricated from
symmetric sequential quasi isotropic layers to predict three
dimensional stress and deformation. This analysis is necessary to
evaluate mechanical integrity of fiber reinforced multi-layer
laminates used for high speed rotating applications such as high
speed impellers. Three dimensional governing equations are written
for rotating composite disc. Explicit solution is obtained with
"Frobenius" expansion series. Based on analytical results, there are
two separate zones of three dimensional stress fields in centre and
edge of rotating disc. For thin discs, out of plane deformations and
stresses are small in comparison with plane ones. For relatively thick
discs deformation and stress fields are three dimensional.
Abstract: The prediction of transmembrane helical segments
(TMHs) in membrane proteins is an important field in the
bioinformatics research. In this paper, a method based on discrete
wavelet transform (DWT) has been developed to predict the number
and location of TMHs in membrane proteins. PDB coded as 1F88 was
chosen as an example to describe the prediction of the number and
location of TMHs in membrane proteins by using this method. One
group of test data sets that contain total 19 protein sequences was
utilized to access the effect of this method. Compared with the
prediction results of DAS, PRED-TMR2, SOSUI, HMMTOP2.0 and
TMHMM2.0, the obtained results indicate that the presented method
has higher prediction accuracy.
Abstract: Gaharu that produced by Aquilaria spp. is classified as
one of the most valuable forest products traded internationally as it is
very resinous, fragrant and highly valuable heartwood. Gaharu has
been widely used in aromatheraphy, medicine, perfume and religious
practices. This work aimed to determine the factors affecting solid
liquid extraction of gaharu oil using hexane as solvent under
experimental condition. The kinetics of extraction was assumed and
verified based on a second-order mechanism. The effect of three
main factors, which were temperature, reaction time and solvent to
solid ratio were investigated to achieve maximum oil yield. The
optimum condition were found at temperature 65°C, 9 hours reaction
time and solvent to solid ratio of 12:1 with 14.5% oil yield. The
kinetics experimental data agrees and well fitted with the second
order extraction model. The initial extraction rate (h) was 0.0115
gmL-1min-1; the extraction capacity (Cs) was 1.282gmL-1; the second
order extraction constant (k) was 0.007 mLg-1min-1 and coefficient of
determination, R2 was 0.945.
Abstract: During 2011 and 2012 seasons, Zaghloul date palms received four sprays of silicon (Si) at 0.05 to 0.1% and selenium (Se) at 0.01 to 0.02%. Growth, nutritional status, yield as well as physical and chemical characteristics of the fruits in response to application of silicon and selenium were investigated. Single and combined applications of silicon at 0.05 to 0.1% and selenium at 0.01 to 0.02% was very effective in enhancing the leaf area, total chlorophylls, percentages of N, P and K in the leaves, yield, bunch weight as well as physical and chemical characteristics of the fruits in relative to the check treatment. Silicon was superior to selenium in this respect. Combined application was favorable than using each alone in this connection. Treating Zaghloul date palms four times with a mixture of silicon at 0.05% + selenium at 0.01% resulted in an economical yield and producing better fruit quality.
Abstract: In this work, we treat the problems related to chemical and petrochemical plants of a certain complex process taking the centrifugal compressor as an example, a system being very complex by its physical structure as well as its behaviour (surge phenomenon). We propose to study the application possibilities of the recent control approaches to the compressor behaviour, and consequently evaluate their contribution in the practical and theoretical fields. Facing the studied industrial process complexity, we choose to make recourse to fuzzy logic for analysis and treatment of its control problem owing to the fact that these techniques constitute the only framework in which the types of imperfect knowledge can jointly be treated (uncertainties, inaccuracies, etc..) offering suitable tools to characterise them. In the particular case of the centrifugal compressor, these imperfections are interpreted by modelling errors, the neglected dynamics, no modelisable dynamics and the parametric variations. The purpose of this paper is to produce a total robust nonlinear controller design method to stabilize the compression process at its optimum steady state by manipulating the gas rate flow. In order to cope with both the parameter uncertainty and the structured non linearity of the plant, the proposed method consists of a linear steady state regulation that ensures robust optimal control and of a nonlinear compensation that achieves the exact input/output linearization.