Abstract: The effect of upstream surface roughness over a
smooth forward facing step in an open channel was investigated
using a particle image velocimetry technique. Three different
upstream surface topographies consisting of hydraulically smooth
wall, sandpaper 36 grit and sand grains were examined. Besides the
wall roughness conditions, all other upstream flow characteristics
were kept constant. It was also observed that upstream roughness
decreased the approach velocity by 2% and 10% but increased the
turbulence intensity by 14% and 35% at the wall-normal distance
corresponding to the top plane of the step compared to smooth
upstream. The results showed that roughness decreased the
reattachment lengths by 14% and 30% compared to smooth upstream.
Although the magnitudes of maximum positive and negative
Reynolds shear stress in separated and reattached region were 0.02Ue
for all the cases, the physical size of both the maximum and
minimum contour levels were decreased by increasing upstream
roughness.
Abstract: By using an adequate thermal barrier coating in
buildings the energy saving will be happened. In this study, a range
of wall paints with different absorption coefficient in different
climates has been investigated. In order to study these effects, heating
and cooling loads of a common building with different ordinary
paints and paint with mineral coating have been calculated. The
effect of building paint in different climatic condition was studied
and comparison was done between ordinary paints and paint with
mineral insulators in temperate climate to obtain optimized energy
consumption. The results have been shown that coatings with
inorganic micro particles as insulation reduce the energy
consumption of buildings around 14%.
Abstract: In this paper, an attempt has been made to analyze the effect of wall window orientation on Daylight Illuminance Ratio (DIR) and energy saving in a building known as “SODHA BERS COMPLEX (SBC)” at Varanasi, UP, India. The building has been designed incorporating all passive concepts for thermal comfort as well daylighting concepts to maximize the use of natural daylighting for the occupants in the day to day activities. The annual average DIR and the energy saving has been estimated by using the DIR model for wall window with different orientations under clear sky condition. It has been found that for south oriented window the energy saving per square meter is more compared to the other orientations due to the higher level of solar insolation for the south window in northern hemisphere whereas energy saving potential is minimum for north oriented wall window. The energy saving potential was 26%, 81% and 51% higher for east, south and west oriented window in comparison to north oriented window. The average annual DIR has same trends of variation as the annual energy saving and it is maximum for south oriented window and minimum for north oriented window.
Abstract: The effectiveness of microchannels in enhancing heat
transfer has been demonstrated in the semiconductor industry. In
order to tap the microscale heat transfer effects into macro
geometries, overcoming the cost and technological constraints,
microscale passages were created in macro geometries machined
using conventional fabrication methods. A cylindrical insert was
placed within a pipe, and geometrical profiles were created on the
outer surface of the insert to enhance heat transfer under steady-state
single-phase liquid flow conditions. However, while heat transfer
coefficient values of above 10 kW/m2·K were achieved, the heat
transfer enhancement was accompanied by undesirable pressure drop
increment. Therefore, this study aims to address the high pressure
drop issue using Constructal theory, a universal design law for both
animate and inanimate systems. Two designs based on Constructal theory were developed to study
the effectiveness of Constructal features in reducing the pressure drop
increment as compared to parallel channels, which are commonly
found in microchannel fabrication. The hydrodynamic and heat
transfer performance for the Tree insert and Constructal fin (Cfin)
insert were studied using experimental methods, and the underlying
mechanisms were substantiated by numerical results. In technical
terms, the objective is to achieve at least comparable increment in
both heat transfer coefficient and pressure drop, if not higher
increment in the former parameter. Results show that the Tree insert improved the heat transfer
performance by more than 16 percent at low flow rates, as compared
to the Tree-parallel insert. However, the heat transfer enhancement
reduced to less than 5 percent at high Reynolds numbers. On the
other hand, the pressure drop increment stayed almost constant at 20
percent. This suggests that the Tree insert has better heat transfer
performance in the low Reynolds number region. More importantly,
the Cfin insert displayed improved heat transfer performance along
with favourable hydrodynamic performance, as compared to Cfinparallel
insert, at all flow rates in this study. At 2 L/min, the
enhancement of heat transfer was more than 30 percent, with 20
percent pressure drop increment, as compared to Cfin-parallel insert.
Furthermore, comparable increment in both heat transfer coefficient
and pressure drop was observed at 8 L/min. In other words, the Cfin
insert successfully achieved the objective of this study. Analysis of the results suggests that bifurcation of flows is
effective in reducing the increment in pressure drop relative to heat
transfer enhancement. Optimising the geometries of the Constructal
fins is therefore the potential future study in achieving a bigger stride
in energy efficiency at much lower costs.
Abstract: This research provides a technical account of
estimating Transition Probability using Time-homogeneous Markov
Jump Process applying by South African HIV/AIDS data from the
Statistics South Africa. It employs Maximum Likelihood Estimator
(MLE) model to explore the possible influence of Transition
Probability of mortality cases in which case the data was based on
actual Statistics South Africa. This was conducted via an integrated
demographic and epidemiological model of South African HIV/AIDS
epidemic. The model was fitted to age-specific HIV prevalence data
and recorded death data using MLE model. Though the previous
model results suggest HIV in South Africa has declined and AIDS
mortality rates have declined since 2002 – 2013, in contrast, our
results differ evidently with the generally accepted HIV models
(Spectrum/EPP and ASSA2008) in South Africa. However, there is
the need for supplementary research to be conducted to enhance the
demographic parameters in the model and as well apply it to each of
the nine (9) provinces of South Africa.
Abstract: Elastic scattering of α-particles from 9Be and 11B
nuclei at different alpha energies have been analyzed. Optical model
parameters (OMPs) of α-particles elastic scattering by these nuclei at
different energies have been obtained. In the present calculations, the
real part of the optical potential are derived by folding of nucleonnucleon
(NN) interaction into nuclear matter density distribution of
the projectile and target nuclei using computer code FRESCO. A
density-dependent version of the M3Y interaction (CDM3Y6), which
is based on the G-matrix elements of the Paris NN potential, has been
used. Volumetric integrals of the real and imaginary potential depth
(JR, JW) have been calculated and found to be energy dependent.
Good agreement between the experimental data and the theoretical
predictions in the whole angular range. In double folding (DF)
calculations, the obtained normalization coefficient Nr is in the range
0.70–1.32.
Abstract: Microstructure and fabric of soils play an important
role on structural properties e.g. stiffness and strength of compacted
earthwork. Traditional quality control monitoring based on moisturedensity
tests neither reflects the variability of soil microstructure nor
provides a direct assessment of structural property, which is the
ultimate objective of the earthwork quality control. Since stiffness
and strength are sensitive to soil microstructure and fabric, any
independent test methods that provide simple, rapid, and direct
measurement of stiffness and strength are anticipated to provide an
effective assessment of compacted earthen materials’ uniformity. In
this study, the soil stiffness gauge (SSG) and the dynamic cone
penetrometer (DCP) were respectively utilized to measure and
monitor the stiffness and strength in companion with traditional
moisture-density measurements of various earthen materials used in
Thailand road construction projects. The practical earthwork quality
control criteria are presented herein in order to assure proper
earthwork quality control and uniform structural property of
compacted earthworks.
Abstract: Community living adjacent to forests and Protected
Areas, especially in South Asian countries, have a common practice
in extracting resources for their living and livelihoods. This
extraction of resources, because the way it is done, destroys the biophysical
features of the area. Deforestation, wildlife poaching, illegal
logging, unauthorized hill cutting etc. are some of the serious issues
of concern for the sustainability of the natural resources that has a
direct impact on environment and climate as a whole. To ensure
community involvement in conservation initiatives of the state,
community based forest management, commonly known as Comanagement,
has been in practice in 6 South Asian countries. These
are -India, Nepal, Sri Lanka, Pakistan, Bhutan and Bangladesh.
Involving community in forestry management was initiated first in
Bangladesh in 1979 and reached as an effective co-management
approach through a several paradigm shifts. This idea of Comanagement
has been institutionalized through a Government Order
(GO) by the Ministry of Environment and Forests, Government of
Bangladesh on November 23, 2009. This GO clearly defines the
structure and functions of Co-management and its different bodies.
Bangladesh Forest Department has been working in association with
community to conserve and manage the Forests and Protected areas
of Bangladesh following this legal document. Demographically
young people constitute the largest segment of population in
Bangladesh. This group, if properly sensitized, can produce valuable
impacts on the conservation initiatives, both by community and
government. This study traced the major factors that motivate
community youths to work effectively with different tiers of comanagement
organizations in conservation of forests and Protected
Areas of Bangladesh. For the purpose of this study, 3 FGDs were
conducted with 30 youths from the community living around the
Protected Areas of Cox’s bazar, South East corner of Bangladesh,
who are actively involved in Co-management organizations. KII were
conducted with 5 key officials of Forest Department stationed at
Cox’s Bazar. 2 FGDs were conducted with the representatives of 7
Co-management organizations working in Cox’s Bazar region and
approaches of different community outreach activities conducted for
forest conservation by 3 private organizations and Projects have been
reviewed. Also secondary literatures were reviewed for the history
and evolution of Co-management in Bangladesh and six South Asian
countries. This study found that innovative community outreach
activities that are financed by public and private sectors involving
youths and community as a whole have played a pivotal role in
conservation of forests and Protected Areas of the region. This
approach can be replicated in other regions of Bangladesh as well as
other countries of South Asia where Co-Management exists in
practice.
Abstract: Solar water heating is a thermodynamic process of
heating water using sunlight with the help of solar water heater. Thus,
solar water heater is a device used to harness solar energy. In this
paper, a modified solar water heating system (MSWHS) has been
proposed over flat plate collector (FPC) and Evacuated tube collector
(ETC). The modifications include selection of materials other than
glass, and glass wool which are conventionally used for fabricating
FPC and ETC. Some modifications in design have also been
proposed. Its collector is made of double layer of semi-cylindrical
acrylic tubes and fibre reinforced plastic (FRP) insulation base. Water
tank is made of double layer of acrylic sheet except base and north
wall. FRP is used in base and north wall of the water tank. A concept
of equivalent thickness has been utilised for calculating the
dimensions of collector plate, acrylic tube and tank. A thermal model for the proposed design of MSWHS is developed
and simulation is carried out on MATLAB for the capacity of 200L
MSWHS having collector area of 1.6 m2, length of acrylic tubes of
2m at an inclination angle 25° which is taken nearly equal to the
latitude of the given location. Latitude of Allahabad is 24.45° N. The
results show that the maximum temperature of water in tank and tube
has been found to be 71.2°C and 73.3°C at 17:00hr and 16:00hr
respectively in March for the climatic data of Allahabad. Theoretical performance analysis has been carried out by varying
number of tubes of collector, the tank capacity and climatic data for
given months of winter and summer.
Abstract: The exploitation of flow pulsation in micro- and
mini-channels is a potentially useful technique for enhancing cooling
of high-end photonics and electronics systems. It is thought that
pulsation alters the thickness of the hydrodynamic and thermal
boundary layers, and hence affects the overall thermal resistance
of the heat sink. Although the fluid mechanics and heat transfer
are inextricably linked, it can be useful to decouple the parameters
to better understand the mechanisms underlying any heat transfer
enhancement. Using two-dimensional, two-component particle image
velocimetry, the current work intends to characterize the heat transfer
mechanisms in pulsating flow with a mean Reynolds number of
48 by experimentally quantifying the hydrodynamics of a generic
liquid-cooled channel geometry. Flows circulated through the test
section by a gear pump are modulated using a controller to achieve
sinusoidal flow pulsations with Womersley numbers of 7.45 and
2.36 and an amplitude ratio of 0.75. It is found that the transient
characteristics of the measured velocity profiles are dependent on the
speed of oscillation, in accordance with the analytical solution for
flow in a rectangular channel. A large velocity overshoot is observed
close to the wall at high frequencies, resulting from the interaction
of near-wall viscous stresses and inertial effects of the main fluid
body. The steep velocity gradients at the wall are indicative of
augmented heat transfer, although the local flow reversal may reduce
the upstream temperature difference in heat transfer applications.
While unsteady effects remain evident at the lower frequency, the
annular effect subsides and retreats from the wall. The shear rate at
the wall is increased during the accelerating half-cycle and decreased
during deceleration compared to steady flow, suggesting that the flow
may experience both enhanced and diminished heat transfer during
a single period. Hence, the thickness of the hydrodynamic boundary
layer is reduced for positively moving flow during one half of the
pulsation cycle at the investigated frequencies. It is expected that the
size of the thermal boundary layer is similarly reduced during the
cycle, leading to intervals of heat transfer enhancement.
Abstract: Surface characteristics of Bacillus megaterium strain
were investigated; zeta potential, FTIR and contact angle were
measured. Surface energy components including Lifshitz-van der
Waals, Hamaker constant, and acid/base components (Lewis
acid/Lewis base) were calculated from the contact angle data. The
results showed that the microbial cells were negatively charged over
all pH regions with high values at alkaline region. A hydrophilic
nature for the strain was confirmed by contact angle and free energy
of adhesion between microbial cells. Adsorption affinity of the strain
toward dolomite was studied at different pH values. The results
showed that the cells had a high affinity to dolomite at acid pH
comparing to neutral and alkaline pH. Extended DLVO theory was
applied to calculate interaction energy between B. megaterium cells
and dolomite particles. The adsorption results were in agreement with
the results of Extended DLVO approach. Surface changes occurred
on dolomite surface after the bio-treatment were monitored; contact
angle decreased from 69° to 38° and the mineral’s floatability
decreased from 95% to 25% after the treatment.
Abstract: The cumulative costs for O&M may represent as
much as 65%-90% of the turbine's investment cost. Nowadays the
cost effectiveness concept becomes a decision-making and
technology evaluation metric. The cost of energy metric accounts for
the effect replacement cost and unscheduled maintenance cost
parameters. One key of the proposed approach is the idea of
maintaining the WTs which can be captured via use of a finite state
Markov chain. Such a model can be embedded within a probabilistic
operation and maintenance simulation reflecting the action to be
done. In this paper, an approach of estimating the cost of O&M is
presented. The finite state Markov model is used for decision
problems with number of determined periods (life cycle) to predict
the cost according to various options of maintenance.
Abstract: The railway transport is considered as a one of the
most environmentally friendly mode of transport. With future
prediction of increasing of freight transport there are lines facing
problems with demanded capacity. Increase of the track capacity
could be achieved by infrastructure constructive adjustments. The
contribution shows how the travel time can be minimized and the
track capacity increased by changing some of the basic infrastructure
and operation parameters, for example, the minimal curve radius of
the track, the number of tracks, or the usable track length at stations.
Calculation of the necessary parameter changes is based on the
fundamental physical laws applied to the train movement, and
calculation of the occupation time is dependent on the changes of
controlling the traffic between the stations.
Abstract: Strategic investment decisions are characterized by
high innovation potential and long-term effects on the
competitiveness of enterprises. Due to the uncertainty and risks
involved in this complex decision making process, the need arises for
well-structured support activities. A method that considers cost and
the long-term added value is the cost-benefit effectiveness estimation.
One of those methods is the “profitability estimation focused on
benefits – PEFB”-method developed at the Institute of Management
Cybernetics at RWTH Aachen University. The method copes with
the challenges associated with strategic investment decisions by
integrating long-term non-monetary aspects whilst also mapping the
chronological sequence of an investment within the organization’s
target system. Thus, this method is characterized as a holistic
approach for the evaluation of costs and benefits of an investment.
This participation-oriented method was applied to business
environments in many workshops. The results of the workshops are a
library of more than 96 cost aspects, as well as 122 benefit aspects.
These aspects are preprocessed and comparatively analyzed with
regards to their alignment to a series of risk levels. For the first time,
an accumulation and a distribution of cost and benefit aspects
regarding their impact and probability of occurrence are given. The
results give evidence that the PEFB-method combines precise
measures of financial accounting with the incorporation of benefits.
Finally, the results constitute the basics for using information
technology and data science for decision support when applying
within the PEFB-method.
Abstract: Recent progress in the next generation of automobile
technology is geared towards incorporating information technology
into cars. Collectively called smart cars are bringing intelligence to
cars that provides comfort, convenience and safety. A branch of smart
cars is connected-car system. The key concept in connected-cars is the
sharing of driving information among cars through decentralized
manner enabling collective intelligence. This paper proposes a
foundation of the information model that is necessary to define the
driving information for smart-cars. Road conditions are modeled
through a unique data structure that unambiguously represent the time
variant traffics in the streets. Additionally, the modeled data structure
is exemplified in a navigational scenario and usage using UML.
Optimal driving route searching is also discussed using the proposed
data structure in a dynamically changing road conditions.
Abstract: Cloud computing is a business model which provides
an easier management of computing resources. Cloud users can
request virtual machine and install additional softwares and configure
them if needed. However, user can also request virtual appliance
which provides a better solution to deploy application in much faster
time, as it is ready-built image of operating system with necessary
softwares installed and configured. Large numbers of virtual
appliances are available in different image format. User can
download available appliances from public marketplace and start
using it. However, information published about the virtual appliance
differs from each providers leading to the difficulty in choosing
required virtual appliance as it is composed of specific OS with
standard software version. However, even if user choses the
appliance from respective providers, user doesn’t have any flexibility
to choose their own set of softwares with required OS and
application. In this paper, we propose a referenced architecture for
dynamically customizing virtual appliance and provision them in an
easier manner. We also add our experience in integrating our
proposed architecture with public marketplace and Mi-Cloud, a cloud
management software.
Abstract: The aim of this research is to understand how the
emerging power bloc BRICS employs infrastructure development
narratives to construct a new world order. BRICS is an international
body consisting of five emerging countries that collaborate on
economic and political issues: Brazil, Russia, India, China, and South
Africa. This study explores the projection of infrastructure
development narratives through an analysis of BRICS’ attention to
infrastructure investment and financing, its support of the New
Partnership on African Development and the establishment of the
New Development Bank in Shanghai. The theory of Strategic
Narratives is used to explore BRICS’ commitment to infrastructure
development and to distinguish three layers: system narratives
(BRICS as a global actor to propose development reform), identity
narratives (BRICS as a collective identity joining efforts to act upon
development aspirations) and issue narratives (BRICS committed to a
range of issues of which infrastructure development is prominent).
The methodology that is employed is a narrative analysis of BRICS’
official documents, media statements, and website imagery. A
comparison of these narratives illuminates tensions at the three layers
and among the five member states. Identifying tensions among
development infrastructure narratives provides an indication of how
policymaking for infrastructure development could be improved.
Subsequently, it advances BRICS’ ability to act as a global actor to
construct a new world order.
Abstract: The irradiation of polymeric materials has received
much attention because it can produce diverse changes in chemical
structure and physical properties. Thus, studying the chemical and
structural changes of polymers is important in practice to achieve
optimal conditions for the modification of polymers. The effect of
gamma irradiation on the crystalline structure of poly(vinylidene
fluoride) (PVDF) has been investigated using differential scanning
calorimetry (DSC) and X-ray diffraction techniques (XRD). Gamma
irradiation was carried out in atmosphere air with doses between 100
kGy at 3,000 kGy with a Co-60 source. In the melting thermogram of
the samples irradiated can be seen a bimodal melting endotherm is
detected with two melting temperature. The lower melting
temperature is attributed to melting of crystals originally present and
the higher melting peak due to melting of crystals reorganized upon
heat treatment. These results are consistent with those obtained by
XRD technique showing increasing crystallinity with increasing
irradiation dose, although the melting latent heat is decreasing.
Abstract: The adjoint method has been used as a successful tool to
obtain sensitivity gradients in aerodynamic design and optimisation
for many years. This work presents an alternative approach to the
continuous adjoint formulation that enables one to compute gradients
of a given measure of merit with respect to control parameters other
than those pertaining to geometry. The procedure is then applied to
the steady 2–D compressible Euler and incompressible Navier–Stokes
flow equations. Finally, the results are compared with sensitivities
obtained by finite differences and theoretical values for validation.
Abstract: Nowadays, food safety is a great public concern;
therefore, robust and effective techniques are required for detecting
the safety situation of goods. Hyperspectral Imaging (HSI) is an
attractive material for researchers to inspect food quality and safety
estimation such as meat quality assessment, automated poultry
carcass inspection, quality evaluation of fish, bruise detection of
apples, quality analysis and grading of citrus fruits, bruise detection
of strawberry, visualization of sugar distribution of melons,
measuring ripening of tomatoes, defect detection of pickling
cucumber, and classification of wheat kernels. HSI can be used to
concurrently collect large amounts of spatial and spectral data on the
objects being observed. This technique yields with exceptional
detection skills, which otherwise cannot be achieved with either
imaging or spectroscopy alone. This paper presents a nonlinear
technique based on kernel Fukunaga-Koontz transform (KFKT) for
detection of fat content in ground meat using HSI. The KFKT which
is the nonlinear version of FKT is one of the most effective
techniques for solving problems involving two-pattern nature. The
conventional FKT method has been improved with kernel machines
for increasing the nonlinear discrimination ability and capturing
higher order of statistics of data. The proposed approach in this paper
aims to segment the fat content of the ground meat by regarding the
fat as target class which is tried to be separated from the remaining
classes (as clutter). We have applied the KFKT on visible and nearinfrared
(VNIR) hyperspectral images of ground meat to determine
fat percentage. The experimental studies indicate that the proposed
technique produces high detection performance for fat ratio in ground
meat.