Abstract: Microstructure and mechanical properties of AZ91D
Mg alloys for nonflammable use, containing Ca and Y, were
investigated in this study. Solid solution treatment of AZ91D Mg alloy
with Ca and Y was successfully conducted at 420oC and
supersaturated microstructure with almost all beta phases resolved into
matrix was obtained. After solid solution treatment, the alloy was
annealed at temperatures of 180 and 200oC for time intervals from 1
min to 48 hrs and hardness of each condition was measured by
micro-Vickers method. Peak aging conditions were deduced from the
results as at the temperature of 200oC for 10 hrs. Hot rolling was also
carried out at 400oC by the reduction ratio of 0.6 through 5 passes
followed by recrystallization treatment. Tensile and compressive
properties were measured at room temperature on the specimens of
each process, i.e. as-cast, solution treatment, hot rolling, and
recrystallization.
Abstract: The aim of irrigation is to recharge the available water
in the soil. Quality of irrigation water is essential for the yield and
quality of crops produced, maintenance of soil productivity and
protection of the environment. The analysis of irrigation water arises
as a need to know the impact of irrigation water on the yield of crops,
the effect, and the necessary control measures to rectify the effect of
this for optimum production and yield of crops. This study was conducted to assess the quality of irrigation water
with its performance on crop planted, in Josepdam irrigation scheme
Bacita, Nigeria. Field visits were undertaken to identify and locate
water supply sources and collect water samples from these sources;
X1 Drain, Oshin, River Niger loop and Ndafa. Laboratory
experiments were then undertaken to determine the quality of raw
water from these sources. The analysis was carried for various parameters namely; physical
and chemical analyses after water samples have been taken from four
sources. The samples were tested in laboratory. Results showed that
the raw water sources shows no salinity tendencies with SAR values
less than 1me/l and Ecvaules at Zero while the pH were within the
recommended range by FAO, there are increase in potassium and
sulphate content contamination in three of the location. From this, it
is recommended that there should be proper monitoring of the
scheme by conducting analysis of water and soil in the environment,
preferable test should be carried out at least one year to cover the
impact of seasonal variations and to determine the physical and
chemical analysis of the water used for irrigation at the scheme.
Abstract: In this study, total fatty acid composition of muscle
lipids of Cyprinus carpio L. living in Suğla Dam Lake, Altinapa Dam
Lake, Eğirdir Lake and Burdur Lake were determined using GC.
During this study, for the summer season of July was taken from each
region of the land and they were stored in deep-freeze set to -20
degrees until the analysis date. At the end of the analyses, 30
different fatty acids were found in the composition of Cyprinus
carpio L. which lives in different lakes. Cyprinus carpio Suğla Dam
Lake of polyunsaturated fatty acids (PUFAs), were higher than other
lakes. Cyprinus carpio L. was the highest in the major SFA palmitic
acid. Polyunsaturated fatty acids (PUFA) of carp, the most abundant
fish species in all lakes, were found to be higher than those of
saturated fatty acids (SFA) in all lakes. Palmitic acid was the major
SFA in all lakes. Oleic acid was identified as the major MUFA.
Docosahexaenoic acid (DHA) was the most abundant in all lakes. ω3
fatty acid composition was higher than the percentage of the
percentage ω6 fatty acids in all lake. ω3/ω6 rates of Cyprinus carpio
L. Suğla Dam Lake, Altinapa Dam Lake, Eğirdir Lake and Burdur
Lake, 2.12, 1.19, 2.15, 2.87, and 2.82, respectively. Docosahexaenoic
acid (DHA) was the major PUFA in Eğirdir and Burdur lakes,
whereas linoleic acid (LA) was the major PUFA in Altinapa and
Suğla Dam Lakes. It was shown that the fatty acid composition in the
muscle of carp was significantly influenced by different lakes.
Abstract: Aerobic dance has becoming a popular mode of
exercise especially among women due to its fun nature. With a catchy
music background and joyful dance steps, aerobic dancers would be
able to have fun while sweating out. Depending on its level of
aggressiveness, aerobic may also improve and maintain
cardiorespiratory fitness other than being a great tool for weight loss.
This study intends to prove that aerobic dance activity can bring the
same, if not better impacts on health than other types of
cardiovascular exercise such as jogging and cycling. The objective of
this study was to evaluate and identify the effect of six weeks aerobic
dance on cardiovascular fitness and weight loss among women. This
study, which was held in Seremban Fit Challenge, used a quasiexperimental
design. The subjects selected include a total of 14
women (n = 14) with age (32.4 years old ± 9.1), weight (65.93 kg ±
11.24) and height (165.36 ± 3.46) who joined the Seremban Fit
Challenge Season 13. The subjects were asked to join an aerobic
dance class with a duration of one hour for six weeks in a row. As for
the outcome, cardiovascular fitness was measured with a 1-mile run
test while any changes on weight were measured using the weighing
scale. The result showed that there was a significant difference
between pre and post-test for cardiovascular fitness when p = 0.02
Abstract: In the deep south of Thailand, checkpoints for people
verification are necessary for the security management of risk zones,
such as official buildings in the conflict area. In this paper, we
propose an automatic checkpoint system that verifies persons using
information from ID cards and facial features. The methods for a
person’s information abstraction and verification are introduced
based on useful information such as ID number and name, extracted
from official cards, and facial images from videos. The proposed
system shows promising results and has a real impact on the local
society.
Abstract: Introduction: To update ourselves and understand the
concept of latest electronic formats available for Health care
providers and how it could be used and developed as per standards.
The idea is to correlate between the patients Manual Medical Records
keeping and maintaining patients Electronic Information in a Health
care setup in this world. Furthermore, this stands with adapting to the
right technology depending upon the organization and improve our
quality and quantity of Healthcare providing skills. Objective: The
concept and theory is to explain the terms of Electronic Medical
Record (EMR), Electronic Health Record (EHR) and Personal Health
Record (PHR) and selecting the best technical among the available
Electronic sources and software before implementing. It is to guide
and make sure the technology used by the end users without any
doubts and difficulties. The idea is to evaluate is to admire the uses
and barriers of EMR-EHR-PHR. Aim and Scope: The target is to
achieve the health care providers like Physicians, Nurses, Therapists,
Medical Bill reimbursements, Insurances and Government to assess
the patient’s information on easy and systematic manner without
diluting the confidentiality of patient’s information. Method: Health
Information Technology can be implemented with the help of
Organisations providing with legal guidelines and help to stand by
the health care provider. The main objective is to select the correct
embedded and affordable database management software and
generating large-scale data. The parallel need is to know how the
latest software available in the market. Conclusion: The question lies
here is implementing the Electronic information system with
healthcare providers and organization. The clinicians are the main
users of the technology and manage us to “go paperless”. The fact is
that day today changing technologically is very sound and up to date.
Basically, the idea is to tell how to store the data electronically safe
and secure. All three exemplifies the fact that an electronic format
has its own benefit as well as barriers.
Abstract: This paper aims to link together the concepts of job
satisfaction, work engagement, trust, job meaningfulness and loyalty
to the organisation focusing on specific type of employment –
academic jobs. The research investigates the relationships between
job satisfaction, work engagement and loyalty as well as the impact
of trust and job meaningfulness on the work engagement and loyalty.
The survey was conducted in one of the largest Latvian higher
education institutions and the sample was drawn from academic staff
(n=326). Structured questionnaire with 44 reflective type questions
was developed to measure the constructs. Data was analysed using
SPSS and Smart-PLS software. Variance based structural equation
modelling (PLS-SEM) technique was used to test the model and to
predict the most important factors relevant to employee engagement
and loyalty. The first order model included two endogenous
constructs (loyalty and intention to stay and recommend to work in
this organisation, and employee engagement), as well as six
exogenous constructs (feeling of fair treatment and trust in
management; career growth opportunities; compensation, pay and
benefits; management; colleagues and teamwork; and finally job
meaningfulness). Job satisfaction was developed as second order
construct and both: first and second order models were designed for
data analysis. It was found that academics are more engaged than
satisfied with their work and main reason for that was found to be job
meaningfulness, which is significant predictor for work engagement,
but not for job satisfaction. Compensation is not significantly related
to work engagement, but only to job satisfaction. Trust was not
significantly related neither to engagement, nor to satisfaction,
however, it appeared to be significant predictor of loyalty and
intentions to stay with the University. Paper revealed academic jobs
as specific kind of employment where employees can be more
engaged than satisfied and highlighted the specific role of job
meaningfulness in the University settings.
Abstract: Motion response of floating structures is of great
concern in marine engineering. Nonlinearity is an inherent property
of any floating bodies subjected to irregular waves. These floating
structures are continuously subjected to environmental loadings from
wave, current, wind etc. This can result in undesirable motions of the
vessel which may challenge the operability. For a floating body to
remain in its position, it should be able to induce a restoring force
when displaced. Mooring is provided to enable this restoring force.
This paper discusses the hydrodynamic performance and motion
characteristics of an 8 point spread mooring system applied to a pipe
laying barge operating in the West African sea. The modelling of the
barge is done using a computer aided-design (CAD) software
RHINOCEROS. Irregular waves are generated using a suitable wave
spectrum. Both frequency domain and time domain analysis is done.
Numerical simulations based on potential theory are carried out to
find the responses and hydrodynamic performance of the barge in
both free floating as well as moored conditions. Initially, potential
flow frequency domain analysis is done to obtain the Response
Amplitude Operator (RAO) which gives an idea about the structural
motion in free floating state. RAOs for different wave headings are
analyzed. In the following step, a time domain analysis is carried out
to obtain the responses of the structure in the moored condition. In
this study, wave induced motions are only taken into consideration.
Wind and current loads are ruled out and shall be included in further
studies. For the current study, 2000 seconds simulation is taken. The
results represent wave induced motion responses, mooring line
tensions and identify critical mooring lines.
Abstract: We have aimed to produce a self-cleaning transparent
polymer coating with polyurethane (PU) matrix as the latter is highly
solvent, chemical and weather resistant having good mechanical
properties. Nano-silica modified by 1H, 1H, 2H, 2Hperflurooctyltriethoxysilane
was incorporated into the PU matrix for
attaining self-cleaning ability through hydrophobicity. The
modification was confirmed by particle size analysis and scanning
electron microscopy (SEM). Thermo-gravimetric (TGA) studies were
carried to ascertain the grafting of silane onto the silica. Several
coating formulations were prepared by varying the silica loading
content and compared to a commercial equivalent. The effect of
dispersion and the morphology of the coated films were assessed by
SEM analysis. All coating standardized tests like solvent resistance,
adhesion, flexibility, acid, alkali, gloss etc. have been performed as
per ASTM standards. Water contact angle studies were conducted to
analyze the hydrophobic character of the coating. In addition, the
coatings were also subjected to salt spray and accelerated weather
testing to analyze the durability of the coating.
Abstract: At the Savonia University of Applied Sciences (UAS),
curriculum and studies have been improved by applying an Open
Innovation Space approach (OIS). It is based on multidisciplinary
action learning. The key elements of OIS-ideology are work-life
orientation, and student-centric communal learning. In this approach,
every participant can learn from each other and innovations will be
created. In this social innovation educational approach, all practices
are carried out in close collaboration with enterprises in real-life
settings, not in classrooms. As an example, in this paper, Savonia
UAS’s Future Food RDI hub (FF) shows how OIS practices are
implemented by providing food product development and consumer
research services for enterprises in close collaboration with
academicians, students and consumers. In particular one example of
OIS experimentation in the field is provided by a consumer research
carried out utilizing verbal analysis protocol combined with audiovisual
observation (VAP-WAVO). In this case, all co-learners were
acting together in supermarket settings to collect the relevant data for
a product development and the marketing department of a company.
The company benefitted from the results obtained, students were
more satisfied with their studies, educators and academicians were
able to obtain good evidence for further collaboration as well as
renewing curriculum contents based on the requirements of working
life. In addition, society will benefit over time as young university
adults find careers more easily through their OIS related food science
studies. Also this knowledge interaction model re-news education
practices and brings working-life closer to educational research
institutes.
Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.
Abstract: The beginning of 21st century has witnessed new
advancements in the design and use of new materials for biosensing
applications, from nano to macro, protein to tissue. Traditional
analytical methods lack a complete toolset to describe the
complexities introduced by living systems, pathological relations,
discrete hierarchical materials, cross-phase interactions, and
structure-property dependencies. Materiomics – via systematic
molecular dynamics (MD) simulation – can provide structureprocess-
property relations by using a materials science approach
linking mechanisms across scales and enables oriented biosensor
design. With this approach, DNA biosensors can be utilized to detect
disease biomarkers present in individuals’ breath such as acetone for
diabetes. Our wireless sensor array based on single-stranded DNA
(ssDNA)-decorated single-walled carbon nanotubes (SWNT) has
successfully detected trace amount of various chemicals in vapor
differentiated by pattern recognition. Here, we present how MD
simulation can revolutionize the way of design and screening of DNA
aptamers for targeting biomarkers related to oral diseases and oral
health monitoring. It demonstrates great potential to be utilized to
build a library of DNDA sequences for reliable detection of several
biomarkers of one specific disease, and as well provides a new
methodology of creating, designing, and applying of biosensors.
Abstract: Concrete is an essential building material which is
widely used in construction industry all over the world due to its
compressible strength. Curing of concrete plays a vital role in
durability and other performance necessities. Improper curing can
affect the concrete performance and durability easily. When areas
like scarcity of water, structures is not accessible by humans external
curing cannot be performed, so we opt for internal curing. Internal
curing (or) self curing plays a major role in developing the concrete
pore structure and microstructure. The concept of internal curing is to
enhance the hydration process to maintain the temperature uniformly.
The evaporation of water in the concrete is reduced by self curing
agent (Super Absorbing Polymer – SAP) there by increasing the
water retention capacity of the concrete. The research work was
carried out to reduce water, which is prime material used for concrete
in the construction industry. Concrete curing plays a major role in
developing hydration process. Concept of self curing will reduce the
evaporation of water from concrete. Self curing will increase water
retention capacity as compared to the conventional concrete. Proper
self curing (or) internal curing increases the strength, durability and
performance of concrete. Super absorbing Polymer (SAP) used as
internal curing agent. In this study 0.2% to 0.4% of SAP was varied
in different grade of high strength concrete. In the experiment
replacement of cement by silica fumes with 5%, 10% and 15% are
studied. It is found that replacement of silica fumes by 10 % gives
more strength and durability when compared to others.
Abstract: The construction of most coastal infrastructure developments around the world are usually made considering wave height, current velocities and river discharges; however, little effort has been paid to surveying sediment transport during dredging or the modification to currents outside the ports or marinas during and after the construction. This study shows a complete survey during the construction of one of the largest ports of the Gulf of Mexico. An anchored Acoustic Doppler Current Velocity profiler (ADCP), a towed ADCP and a combination of model outputs were used at the Veracruz port construction in order to describe the hourly sediment transport and current modifications in and out of the new port. Owing to the stability of the system the new port was construction inside Vergara Bay, a low wave energy system with a tidal range of up to 0.40 m. The results show a two-current system pattern within the bay. The north side of the bay has an anticyclonic gyre, while the southern part of the bay shows a cyclonic gyre. Sediment transport trajectories were made every hour using the anchored ADCP, a numerical model and the weekly data obtained from the towed ADCP within the entire bay. The sediment transport trajectories were carefully tracked since the bay is surrounded by coral reef structures which are sensitive to sedimentation rate and water turbidity. The survey shows that during dredging and rock input used to build the wave breaker sediments were locally added (< 2500 m2) and local currents disperse it in less than 4 h. While the river input located in the middle of the bay and the sewer system plant may add more than 10 times this amount during a rainy day or during the tourist season. Finally, the coastal line obtained seasonally with a drone suggests that the southern part of the bay has not been modified by the construction of the new port located in the northern part of the bay, owing to the two subsystem division of the bay.
Abstract: The simulation in wind tunnel is used thoroughly to model real situations of drainages of air. Besides the automotive industry, a great number of applications can be numbered: dispersion of pollutant, studies of pedestrians’ comfort, and dispersion of particles. This work had the objective of visualizing the characteristics aerodynamics of two automobiles in different ways. To accomplish that drainage of air a fan that generated a speed exists (measured with anemometer of hot thread) of 4,1m/s and 4,95m/s. To visualize the path of the air through the cars, in the wind tunnel, smoke was used, obtained with it burns of vegetable oil. For “to do smoke” vegetable oil was used, that was burned for a tension of 20V generated by a thread of 2,5mm. The cars were placed inside of the wind tunnel with the drainage of “air-smoke” and photographed, registering like this the path lines around them, in the 3 different speeds.
Abstract: A combined heat and power (CHP) system is an efficient and clean way to generate power (electricity). Heat produced by the CHP system can be used for water and space heating. The CHP system which uses hydrogen as fuel produces zero carbon emission. Its’ efficiency can reach more than 80% whereas that of a traditional power station can only reach up to 50% because much of the thermal energy is wasted. The other advantages of CHP systems include that they can decentralize energy generation, improve energy security and sustainability, and significantly reduce the energy cost to the users. This paper presents the economic benefits of using a CHP system in the domestic environment. For this analysis, natural gas is considered as potential fuel as the hydrogen fuel cell based CHP systems are rarely used. UK government incentives for CHP systems are also considered as the added benefit. Results show that CHP requires a significant initial investment in returns it can reduce the annual energy bill significantly. Results show that an investment may be paid back in 7 years. After the back period, CHP can run for about 3 years as most of the CHP manufacturers provide 10 year warranty.
Abstract: The paper presents an additive manufacturing process for the production of metal and composite parts. It is termed as composite metal foil manufacturing and is a combination of laminated object manufacturing and brazing techniques. The process has been described in detail and is being used to produce dissimilar aluminum to copper foil single lap joints. A three dimensional finite element model has been developed to study the thermo-mechanical characteristics of the dissimilar Al/Cu single lap joint. The effects of thermal stress and strain have been analyzed by carrying out transient thermal analysis on the heated plates used to join the two 0.1mm thin metal foils. Tensile test has been carried out on the foils before joining and after the single Al/Cu lap joints are made, they are subjected to tensile lap-shear test to analyze the effect of heat on the foils. The analyses are designed to assess the mechanical integrity of the foils after the brazing process and understand whether or not the heat treatment has an effect on the fracture modes of the produced specimens.
Abstract: E-government has been adopted and used by many governments/countries around the world including Ghana to provide citizens and businesses with more accurate, real-time, and high quality services and information. The objective of this paper is to present an overview of the Government of Ghana’s (GoG) adoption and implement of e-government and its usage by the Ministries, Departments and its agencies (MDAs) as well as other public sector institutions to deliver efficient public service to the general public i.e. citizens, business etc. Government implementation of e-government focused on facilitating effective delivery of government service to the public and ultimately to provide efficient government-wide electronic means of sharing information and knowledge through a network infrastructure developed to connect all major towns and cities, Ministries, Departments and Agencies and other public sector organizations in Ghana. One aim for the Government of Ghana use of ICT in public administration is to improve productivity in government administration and service by facilitating exchange of information to enable better interaction and coordination of work among MDAs, citizens and private businesses. The study was prepared using secondary sources of data from government policy documents, national and international published reports, journal articles, and web sources. This study indicates that through the e-government initiative, currently citizens and businesses can access and pay for services such as renewal of driving license, business registration, payment of taxes, acquisition of marriage and birth certificates as well as application for passport through the GoG electronic service (eservice) and electronic payment (epay) portal. Further, this study shows that there is enormous commitment from GoG to adopt and implement e-government as a tool not only to transform the business of government but also to bring efficiency in public services delivered by the MDAs. To ascertain this, a further study need to be carried out to determine if the use of e-government has brought about the anticipated improvements and efficiency in service delivery of MDAs and other state institutions in Ghana.
Abstract: In order to study the Mutual effect of genotype ×
environment for the percent of oil index in sunflower items, an
experiment was accomplished form complete random block designs
in four iteration and was four diverse researching station comprising
Esfahan, Birjand, Sari, and Karaj. Complex variance analysis showed
that there is an important diversity between the items under
investigation. The results relevant the coefficient variation of items
Azargol and Vidoc has respectively allocated the minimum
coefficient of variations. According to the results extrapolated from
Shokla stability variance, the Items Brocar, Allison and Fabiola, are
among the stable genotypes for oil percent respectively. In the biplot
GGE, the location under investigations divided in two superenvironments,
first one comprised of locations naming Esfahan,
Karaj, and Birjand, and second one were such a location as Sari. By
this point of view, in the first super-environment, the Item Fabiola
and in the second Almanzor item was among the best items and
crops.
Abstract: Nanofibers are defined as fibers with diameters less
than 100 nanometers. In this study, behaviours of activated carbon
nanofiber (ACNF), carbon nanofiber (CNF), polyacrylonitrile/ carbon
nanotube (PAN/CNT), polyvinyl alcohol/nanosilver (PVA/Ag) in
proton exchange membrane (PEM) fuel cells are investigated
experimentally. This material was used as gas diffusion layer (GDL)
in PEM fuel cells. In this study, the electrical conductivities of
nanofiber and nanofiber/nanoparticles have been studied to
understand their effects on PEM fuel cell performance. According to
the experimental results, the maximum electrical conductivity
performance of the fuel cell with nanofiber was found to be at
PVA/Ag (at UConn condition). The electrical conductivities of CNF,
ACNF, PAN/CNT are lower for PEM. The resistance of cell with
PVA/Ag is lower than the resistance of cell with PAN/CNT, ACNF,
CNF.