Abstract: The out-of-band impedance environment is considered
to be of paramount importance in engineering the in-band impedance
environment. Presenting the frequency independent and constant outof-
band impedances across the wide modulation bandwidth is
extremely important for reliable device characterization for future
wireless systems. This paper presents an out-of-band impedance
optimization scheme based on simultaneous engineering of
significant baseband components IF1 (twice the modulation
frequency) and IF2 (four times the modulation frequency) and higher
baseband components such as IF3 (six times the modulation
frequency) and IF4 (eight times the modulation frequency) to
engineer the in-band impedance environment. The investigations
were carried out on a 10W GaN HEMT device driven to deliver a
peak envelope power of approximately 40.5dBm under modulated
excitation. The presentation of frequency independent baseband
impedances to all the significant baseband components whilst
maintaining the optimum termination for fundamental tones as well
as reactive termination for 2nd harmonic under class-J mode of
operation has outlined separate optimum impedances for best
intermodulation (IM) linearity.
Abstract: The study of the aerodynamics related to the
improvement in the acting of airplanes and automobiles with the
objective of being reduced the effect of the attrition of the air on
structures, providing larger speeds and smaller consumption of fuel.
The application of the knowledge of the aerodynamics not more
limits to the aeronautical and automobile industries. Therefore, this
research aims to design and construction of a wind tunnel to perform
aerodynamic analysis in bodies of cars, seeking greater efficiency.
Therefore, this research aims to design and construction of a wind
tunnel to perform aerodynamic analysis in bodies of cars, seeking
greater efficiency. For this, a methodology for wind tunnel type
selection is designed to be built, taking into account the various
existing configurations in which chose to build an open circuit tunnel,
due to the lower complexity of construction and installation;
operational simplicity and low cost. The guidelines for the project
were teaching: the layer that limits study and analyze specimens with
different geometries. For the variation of pressure in the test, section
of a switched gauge used a pitot tube. Thus, it was possible to obtain
quantitative and qualitative results, which proved to be satisfactory.
Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.
Abstract: This paper presents the experimental results of 11 kV
and 33 kV silicon composite insulators under artificial salt and urea
polluted conditions. The tests were carried out under different
seasons like summer, winter, and monsoon. The artificial pollution is
prepared by properly dissolving the salt and urea in the water. The
prepared salt and urea pollutions are sprayed on the insulators and
dried up for sufficiently large time. The process is continued until a
uniform layer is formed on the surface of insulator. For each insulator
rating, four samples were tested. The maximum leakage current and
breakdown voltage were measured. From experimental data,
performance of test specimen is evaluated by comparing breakdown
voltage and leakage current during different seasons when exposed to
salt and urea polluted conditions. From these results the performance
of the insulators can be predicted when they are installed in
industrial, agricultural, and coastal areas. The experimental tests were
carried out in the High Voltage laboratory using two stage cascade
transformer having the rating of 1000 kVA, 500 kV.
Abstract: The study assessed the effectiveness of Pawpaw
(Carica papaya) wood in reducing the concentrations of heavy
metals in wastewater acting as a bio-sorbent. The following heavy
metals were considered; Zinc, Cadmium, Lead, Copper, Iron,
Selenium, Nickel and Manganese. The physiochemical properties of
Carica papaya stem were studied. The experimental sample was
sourced from the trunk of a felled matured pawpaw tree. Wastewater
for experimental use was prepared by dissolving soil samples
collected from a dump site at Owerri, Imo state of Nigeria in water.
The concentration of each metal remaining in solution as residual
metal after bio-sorption was determined using Atomic absorption
Spectrometer. The effects of pH and initial heavy metal concentration
were studied in a batch reactor. The results of Spectrometer test
showed that there were different functional groups detected in the
Carica papaya stem biomass. There was increase in metal removal as
the pH increased for all the metals considered except for Nickel and
Manganese. Optimum bio-sorption occurred at pH 5.9 with 5g/100ml
solution of bio-sorbent. The results of the study showed that the
treated wastewater is fit for irrigation purpose based on Canada
wastewater quality guideline for the protection of Agricultural
standard. This approach thus provides a cost effective and
environmentally friendly option for treating wastewater.
Abstract: The research aims to investigate the occurrence of
multidrug-resistant Acinetobacter, in carrot and estimate the role of
carrot in its transmission in a rapidly growing urban population.
Thus, 50 carrot samples were collected from Jakara wastewater
irrigation farms and are analyzed on MacConkey agar and screened
by Microbact 24E (Oxoid) and susceptibility of isolates is tested
against 10 commonly used antibiotics. Acinetobacter baumannii and
A. lwoffii were isolated in 22.00% and 16% of samples respectively.
Resistance to ceporex and penicillin of 36.36% and 27.27% in A.
baumannii, and sensitivity to ofloxacin, pefloxacin, gentimycin and
co-trimoxazole were observed. However, for A. lwoffii apart from
37.50% resistance to ceporex, it was also resistant to all other drugs
tested. There were similarities in the resistances shown by A.
baumannii and A. lwoffii to fluoroquinolones and β- lactame drug
families in addition to between sulfonamide and animoglycoside
demonstrated by A. lwoffii. Significant correlation in similarities were
observed at P < 0.05 to CPX to NA (46.2%), and SXT to AU (52.6%)
A. baumannii and A. lwoffii respectively and high multi drug
resistance (MDR) of 27.27% and 62.50% by A. baumannii and A.
lwoffii respectively. The occurrence of multidrug-resistance pathogen
in carrot is a serious challenge to public health care, especially in a
rapidly growing urban population where subsistence agriculture
contributes greatly to urban livelihood and source of vegetables.
Abstract: Energy consumption of a hotel can be a hot topic in
smart city; it is difficult to evaluate the contribution of impact factors
to energy consumption of a hotel. Therefore, grasping the key impact
factors has great effect on the energy saving management of a hotel.
Based on the SPIRTPAT model, we establish the identity with the
impact factors of occupancy rate, unit area of revenue, temperature
factor, unit revenue of energy consumption. In this paper, we use the
LMDI (Logarithmic Mean Divisia Index) to decompose the impact
factors of energy consumption of hotel from Jan. to Dec. in 2001. The
results indicate that the occupancy rate and unit area of revenue are the
main factors that can increase unit area of energy consumption, and the
unit revenue of energy consumption is the main factor to restrain the
growth of unit area of energy consumption. When the energy
consumption of hotel can appear abnormal, the hotel manager can
carry out energy saving management and control according to the
contribution value of impact factors.
Abstract: Objective: Acute coronary syndrome is a clinical
condition encompassing ST segments elevation myocardial
infraction, Non ST segment is elevation myocardial infraction and un
stable angina is characterized by ruptured coronary plaque, stress and
myocardial injury. Angina pectoris is a pressure like pain in the chest
that is induced by exertion or stress and relived with in the minute
after cessation of effort or using sublingual nitroglycerin. The present
research was undertaken to study the drug utilization pattern of
antiplatelet drugs for the ischemic heart disease in a tertiary care
hospital. Method: The present study is retrospective drug utilization
study and study period is 6months. The data is collected from the
discharge case sheet of general medicine department from medical
department Rajiv Gandhi institute of medical sciences, Kadapa. The
tentative sample size fixed was 250 patients. Out of 250 cases 19
cases was excluded because of unrelated data. Results: A total of 250
prescriptions were collected for the study according to the inclusion
criteria 233 prescriptions were diagnosed with ischemic heart disease
17 prescriptions were excluded due to unrelated information. out of
233 prescriptions 128 are male (54.9%) and 105 patients are were
female (45%). According to the gender distribution, the prevalence of
ischemic heart disease in males are 90 (70.31%) and females are 39
(37.1%). In the same way the prevalence of ischemic heart disease
along with cerebrovascular disease in males are 39 (29.6%) and
females are 66 (62.6%). Conclusion: We found that 94.8% of drug
utilization of antiplatelet drugs was achieved in the Rajiv Gandhi
institute of medical sciences, Kadapa from 2011-2012.
Abstract: The paper deals with possibilities of increase train
capacity by using a new type of railway wagon. In the first part is
created a mathematical model to calculate the capacity of the train.
The model is based on the main limiting parameters of the train -
maximum number of axles per train, maximum gross weight of train,
maximum length of train and number of TEUs per one wagon. In the
second part is the model applied to four different model trains with
different composition of the train set and three different average
weights of TEU and a train consisting of a new type of wagons. The
result is to identify where the carrying capacity of the original trains
is higher, respectively less than a capacity of train consisting of a new
type of wagons.
Abstract: Low density polyethylene (LDPE) nanocomposites
with 3, 5 and 7 wt. % cobalt ferrite (CoFe2O4) nanopowder fabricated
with extrusion mixing and followed up by hot press to reach compact
samples. The transmission/reflection measurements were carried out
with a network analyzer in the frequency range of 8-12 GHz. By
increasing the percent of CoFe2O4 nanopowder, reflection loss (S11)
increases, while transferring loss (S21) decreases. Reflectivity (R)
calculations made using S11 and S21. Increase in percent of CoFe2O4
nanopowder up to 7 wt. % in composite leaded to higher reflectivity
amount, and revealed that increasing the percent of CoFe2O4
nanopowder up to 7 wt. % leads to further microwave absorption in
8-12 GHz range.
Abstract: There was a scenario present day that drying of fresh
fruits and vegetables by indirect solar drying by using mechanical
device; hence, an effort was made to develop a small scale solar
tunnel dryer (STD). Drying of spinach is carried out to analyze the
performance of the dryer and to study its drying characteristics. To
evaluate the performance of dryer the independent variables were
selected as air flow rate, loading density and shade net while collector
efficiency, drying efficiency, overall efficiency and specific energy
consumption were selected as responses during performing the
experiments. The spinach was dried from initial moisture content
88.21-94.04% (w.b.) to final moisture content 3.50-5.13% (w.b.). The
drying time considerably reduced as compared to open sun drying of
spinach as sun drying took 15 h for drying. The average collector
efficiency, drying efficiency and overall efficiency were in the range
28.73-61.15%, 11.63% to 22.13%, and 7.61-14.66%, respectively.
Abstract: With the advancement of knowledge about the utility
and impact of sustainability, its feasibility has been explored into
different walks of life. Scientists, however; have established their
knowledge in four areas viz environmental, economic, social and
cultural, popularly termed as four pillars of sustainability. Aspects of
environmental and economic sustainability have been rigorously
researched and practiced and huge volume of strong evidence of
effectiveness has been founded for these two sub-areas. For the social
and cultural aspects of sustainability, dependable evidence of
effectiveness is still to be instituted as the researchers and
practitioners are developing and experimenting methods across the
globe. Therefore, the present research aimed to identify globally used
practices of social and cultural sustainability and through evidence
synthesis assess their outcomes to determine the effectiveness of
those practices. A PICO format steered the methodology which
included all populations, popular sustainability practices including
walkability/cycle tracks, social/recreational spaces, privacy, health &
human services and barrier free built environment, comparators
included ‘Before’ and ‘After’, ‘With’ and ‘Without’, ‘More’ and
‘Less’ and outcomes included Social well-being, cultural coexistence,
quality of life, ethics and morality, social capital, sense of
place, education, health, recreation and leisure, and holistic
development. Search of literature included major electronic
databases, search websites, organizational resources, directory of
open access journals and subscribed journals. Grey literature,
however, was not included. Inclusion criteria filtered studies on the
basis of research designs such as total randomization, quasirandomization,
cluster randomization, observational or single studies
and certain types of analysis. Studies with combined outcomes were
considered but studies focusing only on environmental and/or
economic outcomes were rejected. Data extraction, critical appraisal
and evidence synthesis was carried out using customized tabulation,
reference manager and CASP tool. Partial meta-analysis was carried
out and calculation of pooled effects and forest plotting were done.
As many as 13 studies finally included for final synthesis explained
the impact of targeted practices on health, behavioural and social
dimensions. Objectivity in the measurement of health outcomes
facilitated quantitative synthesis of studies which highlighted the
impact of sustainability methods on physical activity, Body Mass
Index, perinatal outcomes and child health. Studies synthesized
qualitatively (and also quantitatively) showed outcomes such as
routines, family relations, citizenship, trust in relationships, social
inclusion, neighbourhood social capital, wellbeing, habitability and
family’s social processes. The synthesized evidence indicates slight
effectiveness and efficacy of social and cultural sustainability on the
targeted outcomes. Further synthesis revealed that such results of this
study are due weak research designs and disintegrated implementations. If architects and other practitioners deliver their
interventions in collaboration with research bodies and policy
makers, a stronger evidence-base in this area could be generated.
Abstract: Segmentation of left ventricle (LV) from cardiac
ultrasound images provides a quantitative functional analysis of the
heart to diagnose disease. Active Shape Model (ASM) is widely used
for LV segmentation, but it suffers from the drawback that
initialization of the shape model is not sufficiently close to the target,
especially when dealing with abnormal shapes in disease. In this work,
a two-step framework is improved to achieve a fast and efficient LV
segmentation. First, a robust and efficient detection based on Hough
forest localizes cardiac feature points. Such feature points are used to
predict the initial fitting of the LV shape model. Second, ASM is
applied to further fit the LV shape model to the cardiac ultrasound
image. With the robust initialization, ASM is able to achieve more
accurate segmentation. The performance of the proposed method is
evaluated on a dataset of 810 cardiac ultrasound images that are mostly
abnormal shapes. This proposed method is compared with several
combinations of ASM and existing initialization methods. Our
experiment results demonstrate that accuracy of the proposed method
for feature point detection for initialization was 40% higher than the
existing methods. Moreover, the proposed method significantly
reduces the number of necessary ASM fitting loops and thus speeds up
the whole segmentation process. Therefore, the proposed method is
able to achieve more accurate and efficient segmentation results and is
applicable to unusual shapes of heart with cardiac diseases, such as left
atrial enlargement.
Abstract: Game-based learning can enhance the learning
motivation of students and provide a means for them to learn through
playing games. This study used augmented reality technology to
develop an interactive card game as a game-based teaching aid for
delivering elementary school science course content with the aim of
enhancing student learning processes and outcomes. Through playing
the proposed card game, students can familiarize themselves with
appearance, features, and foraging behaviors of insects. The system
records the actions of students, enabling teachers to determine their
students’ learning progress. In this study, 37 students participated in an
assessment experiment and provided feedback through questionnaires.
Their responses indicated that they were significantly more motivated
to learn after playing the game, and their feedback was mostly
positive.
Abstract: Test automation allows performing difficult and time
consuming manual software testing tasks efficiently, quickly and
repeatedly. However, development and maintenance of automated
tests is expensive, so it needs a proper prioritization what to automate
first. This paper describes a simple yet efficient approach for such
prioritization of test cases based on the effort needed for both manual
execution and software test automation. The suggested approach is
very flexible because it allows working with a variety of assessment
methods, and adding or removing new candidates at any time. The
theoretical ideas presented in this article have been successfully
applied in real world situations in several software companies by the
authors and their colleagues including testing of real estate websites,
cryptographic and authentication solutions, OSGi-based middleware
framework that has been applied in various systems for smart homes,
connected cars, production plants, sensors, home appliances, car head
units and engine control units (ECU), vending machines, medical
devices, industry equipment and other devices that either contain or
are connected to an embedded service gateway.
Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: The paper presents a method in which the expert
knowledge is applied to fuzzy inference model. Even a less
experienced person could benefit from the use of such a system, e.g.
urban planners, officials. The analysis result is obtained in a very
short time, so a large number of the proposed locations can also be
verified in a short time. The proposed method is intended for testing
of locations of car parks in a city. The paper shows selected examples
of locations of the P&R facilities in cities planning to introduce the
P&R. The analyses of existing objects are also shown in the paper
and they are confronted with the opinions of the system users, with
particular emphasis on unpopular locations. The results of the
analyses are compared to expert analysis of the P&R facilities
location that was outsourced by the city and the opinions about
existing facilities users that were expressed on social networking
sites. The obtained results are consistent with actual users’ feedback.
The proposed method proves to be good, but does not require the
involvement of a large experts team and large financial contributions
for complicated research. The method also provides an opportunity to
show the alternative location of P&R facilities. Although the results
of the method are approximate, they are not worse than results of
analysis of employed experts. The advantage of this method is ease of
use, which simplifies the professional expert analysis. The ability of
analyzing a large number of alternative locations gives a broader
view on the problem. It is valuable that the arduous analysis of the
team of people can be replaced by the model's calculation. According
to the authors, the proposed method is also suitable for
implementation on a GIS platform.
Abstract: Maintenance and design engineers have great concern
for the functioning of rotating machineries due to the vibration
phenomenon. Improper functioning in rotating machinery originates
from the damage to rolling element bearings. The status of rolling
element bearings require advanced technologies to monitor their
health status efficiently and effectively. Avoiding vibration during
machine running conditions is a complicated process. Vibration
simulation should be carried out using suitable sensors/ transducers to
recognize the level of damage on bearing during machine operating
conditions. Various issues arising in rotating systems are interlinked
with bearing faults. This paper presents an approach for fault
diagnosis of bearings using neural networks and time/frequencydomain
vibration analysis.
Abstract: The main objective of this research is to describe the
relationship between organizational climate and organizational
citizenship behavior. In order to examine this relationship, a research
is intended to be carried out in relevant institutions and organizations
operating in the health sector in Turkey. It will be researched that
whether there is a statistically significant relationship between
organizational climate and organizational citizenship behavior
through elated scientific research methods and statistical analysis. In
addition, relationships between the dimensions of organizational
climate and organizational citizenship behavior subscales will be
questioned statistically.
Abstract: The statistical study has become indispensable for various fields of knowledge. Not any different, in Geotechnics the study of probabilistic and statistical methods has gained power considering its use in characterizing the uncertainties inherent in soil properties. One of the situations where engineers are constantly faced is the definition of a probability distribution that represents significantly the sampled data. To be able to discard bad distributions, goodness-of-fit tests are necessary. In this paper, three non-parametric goodness-of-fit tests are applied to a data set computationally generated to test the goodness-of-fit of them to a series of known distributions. It is shown that the use of normal distribution does not always provide satisfactory results regarding physical and behavioral representation of the modeled parameters.