Abstract: In present global scenario, aluminum alloys are
coining the attention of many innovators as competing structural
materials for automotive and space applications. Comparing to other
challenging alloys, especially, 7xxx series aluminum alloys have
been studied seriously because of benefits such as moderate strength;
better deforming characteristics and affordable cost. It is expected
that substitution of aluminum alloys for steels will result in great
improvements in energy economy, durability and recyclability.
However, it is necessary to improve the strength and the formability
levels at low temperatures in aluminum alloys for still better
applications. Aluminum–Zinc–Magnesium with or without other
wetting agent denoted as 7XXX series alloys are medium strength
heat treatable alloys. In addition to Zn, Mg as major alloying
additions, Cu, Mn and Si are the other solute elements which
contribute for the improvement in mechanical properties by suitable
heat treatment process. Subjecting to suitable treatments like age
hardening or cold deformation assisted heat treatments; known as low
temperature thermomechanical treatments (LTMT) the challenging
properties might be incorporated. T6 is the age hardening or
precipitation hardening process with artificial aging cycle whereas T8
comprises of LTMT treatment aged artificially with X% cold
deformation. When the cold deformation is provided after solution
treatment, there is increase in hardness related properties such as
wear resistance, yield and ultimate strength, toughness with the
expense of ductility. During precipitation hardening both hardness
and strength of the samples are increasing. The hardness value may
further improve when room temperature deformation is positively
supported with age hardening known as thermomechanical treatment.
It is intended to perform heat treatment and evaluate hardness, tensile
strength, wear resistance and distribution pattern of reinforcement in
the matrix. 2 to 2.5 and 3 to 3.5 times increase in hardness is reported
in age hardening and LTMT treatments respectively as compared to
as-cast composite. There was better distribution of reinforcements in
the matrix, nearly two fold increase in strength levels and up to 5
times increase in wear resistance are also observed in the present
study.
Abstract: In this paper, an autonomous hovering control method
of multicopter using only Web camera is proposed. Recently, various
control method of an autonomous flight for multicopter are proposed.
But, in the previous proposed methods, a motion capture system
(i. e., OptiTrack) and laser range finder are often used to measure
the position and posture of multicopter. To achieve an autonomous
flight control of multicopter with simple equipments, we propose
an autonomous flight control method using AR marker and Web
camera. AR marker can measure the position of multicopter with
Cartesian coordinate in three dimensional, then its position connects
with aileron, elevator, and accelerator throttle operation. A simple
PID control method is applied to the each operation and adjust
the controller gains. Experimental results are given to show the
effectiveness of our proposed method. Moreover, another simple
operation method for autonomous flight control multicopter is also
proposed.
Abstract: This paper investigates the connotation, and some of
the realistic implications, of the economic reform of health sector in
under developed countries. The paper investigates the issues that
economic reforms have to address, and the policy targets they are
considered to accomplish. The work argues that the development of
economic reform is not connected only with understanding the
priorities and refining them, furthermore with reformation and
restructuring the organizations through which health policies are
employed. Considering various organizational values, that are likely
to be regular to all economic reform programs, a regulatory approach
to institutional reform is unsuitable. The paper further investigates the
selection of economic reform that may as well influence via technical
suggestions and analysis, but the verdict to continue, and the
consequent success of execution, eventually depends on the
progressive political sustainability. The paper concludes by giving
examples of institutional reforms from various underdeveloped
countries and includes recommendation of the responsibility and
control of donor organizations.
Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: Present work deals with the possible use of fertigation
in agriculture and its impact on the availability of mineral nitrogen
(Nmin) in topsoil and subsoil horizons. The aim of the present study is
to demonstrate the effect of the organic matter presence in fertigation
on microbial transformation and availability of mineral nitrogen
forms. The main investigation reason is the potential use of pretreated
waste water, as a source of organic carbon (Corg) and residual
nutrients (Nmin) for fertigation. Laboratory experiment has been
conducted to demonstrate the effect of the arable land fertilization
method on the Nmin availability in different depths of the soil with
the usage of model experimental containers filled with soil from
topsoil and podsoil horizons that were taken from the precise area.
Tufted hairgrass (Deschampsia caespitosa) has been chosen as a
model plant. The water source protection zone Brezova nad Svitavou
has been a research area where significant underground reservoirs of
drinking water of the highest quality are located. From the second
half of the last century local sources of drinking water show
nitrogenous compounds increase that get here almost only from
arable lands. Therefore, an attention of the following text focuses on
the fate of mineral nitrogen in the complex plant-soil. Research
results show that the fertigation application with Corg in a
combination with mineral fertilizer can reduce the amount of Nmin
leached from topsoil horizon of agricultural soils. In addition, some
plants biomass production reduces may occur.
Abstract: In recent decades, particulate matter (PM10) have
received much attention due to its potential adverse health impact and
the subsequent need to better control or regulate these pollutants.
The aim of this paper is focused on study risk assessment of PM10
in four different districts (Shebikah, Masfalah, Aziziyah, Awali) in
Makkah, Saudi Arabia during the period from 1 Ramadan 1434 AH -
27 Safar 1435 AH. Samples were collected by using Low Volume
Sampler (LVS Low Volume Sampler) device and filtration method
for estimating the total concentration of PM10.
The study indicated that the mean PM10 concentrations were 254.6
(186.1 - 343.2) μg/m3 in Shebikah, 184.9 (145.6 - 271.4) μg/m3 in
Masfalah, 162.4 (92.4-253.8) μg/m3 in Aziziyah, and 56.0 (44.5 -
119.8) μg/m3 in Awali. These values did not exceed the permissible
limits in PME (340 μg/m3 as daily average). Furthermore, health
assessment is carried out using AirQ2.2.3 model to estimate the
number of hospital admissions due to respiratory diseases. The
cumulative number of cases per 100,000 were 1534 (18-3050 case),
which lower than that recorded in the United States, Malaysia. The
concentration response coefficient was 0.49 (95% CI 0.05 - 0.70) per
10 μg/m3 increase of PM10.
Abstract: This paper aims to project the construction of a
prototype azimuthal thruster, mounted with materials of low cost and
easy access, testing in a controlled environment to measure their
performance, characteristics and feasibility of future projects. The
construction of the simulation of dynamic positioning software,
responsible for simulating a vessel and reposition it when necessary.
Validation tests were performed in the form of partial or complete
system. These tests validate the system manually or automatically.
The system provides an interface to the user and simulates the
conditions unfavorable positioning of a vessel, accurately calculates
the azimuth angle, the direction of rotation of the helix and the time
that this should be turned on so that the vessel back to position
original. A serial communication connects the Simulation Dynamic
Positioning System with Embedded System causing the usergenerated
data to simulate the DP system arrives in the form of
control signals to the motors of the propellant. This article addresses
issues in the marine industry employees.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: In light of the technological development and its
introduction into the field of education, an online course was
designed in parallel to the 'conventional' course for teaching the
''Qualitative Research Methods''. This course aimed to characterize
learning-teaching processes in a 'Qualitative Research Methods'
course studied in two different frameworks. Moreover, its objective
was to explore the difference between the culture of a physical
learning environment and that of online learning. The research
monitored four learner groups, a total of 72 students, for two years,
two groups from the two course frameworks each year. The courses
were obligatory for M.Ed. students at an academic college of
education and were given by one female-lecturer. The research was
conducted in the qualitative method as a case study in order to attain
insights about occurrences in the actual contexts and sites in which
they transpire. The research tools were open-ended questionnaire and
reflections in the form of vignettes (meaningful short pictures) to all
students as well as an interview with the lecturer. The tools facilitated
not only triangulation but also collecting data consisting of voices
and pictures of teaching and learning. The most prominent findings
are: differences between the two courses in the change features of the
learning environment culture for the acquisition of contents and
qualitative research tools. They were manifested by teaching
methods, illustration aids, lecturer's profile and students' profile.
Abstract: The growth of organic farming practices in the last
few decades is continuing to stimulate the international debate about
this alternative food market. As a part of a PhD project research
about embeddedness in Alternative Food Networks (AFNs), this
paper focuses on the promotional aspects of organic farms websites
from the Madrid region. As a theoretical tool, some knowledge
categories drawn on the geographic studies literature are used to
classify the many ideas expressed in the web pages. By analysing
texts and pictures of 30 websites, the study aims to question how and
to what extent actors from organic world communicate to the
potential customers their personal beliefs about farming practices,
products qualities, and ecological and social benefits. Moreover, the
paper raises the question of whether organic farming laws and
regulations lack of completeness about the social and cultural aspects
of food.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: The main objective of this study was to assess the
seasonal variation of atmospheric polycyclic aromatic hydrocarbon
(PAH) concentrations associated with PM10 in an urban site of Győr,
Hungary. A total of 112 PM10 aerosol samples were collected in the
years of 2012 and 2013 and analyzed for PAHs by gas
chromatography method. The total PAH concentrations (sum of the
concentrations of 19 individual PAH compounds) ranged from 0.19
to 70.16 ng/m3 with the mean value of 12.29 ng/m3. Higher
concentrations of both total PAHs and benzo[a]pyrene (BaP) were
detected in samples collected in the heating seasons. Using BaPequivalent
potency index on the carcinogenic PAH concentration
data, the local population appears to be exposed to significantly
higher cancer risk in the heating seasons. However, the comparison
of the BaP and total PAH concentrations observed for Győr with
other cities it was found that the PAH levels in Győr generally
corresponded to the EU average.
Abstract: Residential buildings consume significant amounts of
energy and produce large amount of emissions and waste. However,
there is a substantial potential for energy savings in this sector which
needs to be evaluated over the life cycle of residential buildings. Life
Cycle Assessment (LCA) methodology has been employed to study
the primary energy uses and associated environmental impacts of
different phases (i.e., product, construction, use, end of life, and
beyond building life) for residential buildings. Four different
alternatives of residential buildings in Vancouver (BC, Canada) with
a 50-year lifespan have been evaluated, including High Rise
Apartment (HRA), Low Rise Apartment (LRA), Single family
Attached House (SAH), and Single family Detached House (SDH).
Life cycle performance of the buildings is evaluated for embodied
energy, embodied environmental impacts, operational energy,
operational environmental impacts, total life-cycle energy, and total
life cycle environmental impacts. Estimation of operational energy
and LCA are performed using DesignBuilder software and Athena
Impact estimator software respectively.
The study results revealed that over the life span of the buildings,
the relationship between the energy use and the environmental
impacts are identical. LRA is found to be the best alternative in terms
of embodied energy use and embodied environmental impacts; while,
HRA showed the best life-cycle performance in terms of minimum
energy use and environmental impacts. Sensitivity analysis has also
been carried out to study the influence of building service lifespan
over 50, 75, and 100 years on the relative significance of embodied
energy and total life cycle energy. The life-cycle energy requirements
for SDH are found to be a significant component among the four
types of residential buildings. The overall disclose that the primary
operations of these buildings accounts for 90% of the total life cycle
energy which far outweighs minor differences in embodied effects
between the buildings.
Abstract: The paper provides a comprehensive analysis of the
sustainable development in the Belgrade Metropolitan Region - BMA
(level NUTS 2) preliminary evaluating the three chosen components:
1) economic growth and developmental changes; 2) competitiveness;
and 3) territorial concentration and industrial specialization. First, we
identified the main results of development changes and economic
growth by applying Shift-share analysis on the metropolitan level.
Second, the empirical evaluation of competitiveness in the BMA is
based on the analysis of absolute and relative values of eight
indicators by Spider method. Paper shows that the consideration of
the national share, industrial mix and metropolitan/regional share in
total Shift share of the BMA, as well as economic/functional
specialization of the BMA indicate very strong process of
deindustrialization. Allocative component of the BMA economic
growth has positive value, reflecting the above-average sector
productivity compared to the national average. Third, the important
positive role of metropolitan/regional component in decomposition of
the BMA economic growth is highlighted as one of the key results.
Finally, comparative analysis of the industrial territorial
concentration in the BMA in relation to Serbia is based on location
quotient (LQ) or Balassa index as a valid measure. The results
indicate absolute and relative differences in decrease of industry
territorial concentration as well as inefficiency of utilizing territorial
capital in the BMA. Results are important for the increase of regional
competitiveness and territorial distribution in this area as well as for
improvement of sustainable metropolitan and sector policies,
planning and governance on this level.
Abstract: Based on Business and Consumer Survey (BCS) data,
the European Commission (EC) regularly publishes the monthly
Economic Sentiment Indicator (ESI) for each EU member state. ESI
is conceptualized as a leading indicator, aimed ad tracking the overall
economic activity. In calculating ESI, the EC employs arbitrarily
chosen weights on 15 BCS response balances. This paper raises the
predictive quality of ESI by applying nonlinear programming to find
such weights that maximize the correlation coefficient of ESI and
year-on-year GDP growth. The obtained results show that the highest
weights are assigned to the response balances of industrial sector
questions, followed by questions from the retail trade sector. This
comes as no surprise since the existing literature shows that the
industrial production is a plausible proxy for the overall Croatian
economic activity and since Croatian GDP is largely influenced by
the aggregate personal consumption.
Abstract: Elastomeric polymer foam has been used widely in
the automotive industry, especially for isolating unwanted vibrations.
Such material is able to absorb unwanted vibration due to its
combination of elastic and viscous properties. However, the ‘creep
effect’, poor stress distribution and susceptibility to high
temperatures are the main disadvantages of such a system.
In this study, improvements in the performance of elastomeric
foam as a vibration isolator were investigated using the concept of
Foam Filled Fluid (FFFluid). In FFFluid devices, the foam takes the
form of capsule shapes, and is mixed with viscous fluid, while the
mixture is contained in a closed vessel. When the FFFluid isolator is
affected by vibrations, energy is absorbed, due to the elastic strain of
the foam. As the foam is compressed, there is also movement of the
fluid, which contributes to further energy absorption as the fluid
shears. Also, and dependent on the design adopted, the packaging
could also attenuate vibration through energy absorption via friction
and/or elastic strain.
The present study focuses on the advantages of the FFFluid
concept over the dry polymeric foam in the role of vibration isolation.
This comparative study between the performance of dry foam and the
FFFluid was made according to experimental procedures. The paper
concludes by evaluating the performance of the FFFluid isolator in
the suspension system of a light vehicle. One outcome of this
research is that the FFFluid may preferable over elastomer isolators
in certain applications, as it enables a reduction in the effects of high
temperatures and of ‘creep effects’, thereby increasing the reliability
and load distribution. The stiffness coefficient of the system has
increased about 60% by using an FFFluid sample. The technology
represented by the FFFluid is therefore considered by this research
suitable for application in the suspension system of a light vehicle.
Abstract: Ant Colony Optimization (ACO) is a promising
modern approach to the unused combinatorial optimization. Here
ACO is applied to finding the shortest during communication link
failure. In this paper, the performances of the prim’s and ACO
algorithm are made. By comparing the time complexity and program
execution time as set of parameters, we demonstrate the pleasant
performance of ACO in finding excellent solution to finding shortest
path during communication link failure.
Abstract: Aging infrastructures became a serious social problem.
This brought out the increased need for the legislation of a new strict
guideline for infrastructure management. Although existing guidelines
provided basics of how to evaluate and manage the condition of
infrastructures, they needed improvements for their evaluation
procedures. Most guidelines mainly focused on the structural
condition of infrastructures and did not properly reflect service aspects
of infrastructures such as performance, public demand, capacity, etc.,
which were significantly valuable to public. Regardless of the
importance, these factors were often neglected in infrastructure
evaluations, because they were quite subjective and difficult to
quantify in rational manner. Thus, this study proposed a framework to
properly identify and evaluate the service indicators. This study
showed that service indicators could be grouped into two categories
and properly evaluated using AHP and Fuzzy. Overall, proposed
framework is expected to assist governmental agency in establishing
effective investment strategies for infrastructure improvements.
Abstract: Food poisoning and infection by bacteria are of public
health significance to both developing and developed countries.
Samples of ogi (akamu) prepared from white and yellow variety of
maize sold in Uturu and Okigwe were analyzed together with the
laboratory prepared ogi for bacterial quality using the standard
microbiological methods. The analyses showed that both white and
yellow variety had total bacterial counts (cfu/g) of 4.0 ×107 and 3.9 x
107 for the laboratory prepared ogi while the commercial ogi had 5.2
x 107 and 4.9 x107, 4.9 x107 and 4.5 x107, 5.4 x107 and 5.0 x107 for
Eke-Okigwe, Up-gate and Nkwo-Achara market respectively. The
Staphylococcal counts ranged from 2.0 x 102 to 5.0 x102 and 1.0 x
102 to 4.0 x102 for the white and yellow variety from the different
markets while Staphylococcal growth was not recorded on the
laboratory prepared ogi. The laboratory prepared ogi had no Coliform
growth while the commercially prepared ogi had counts of 0.5 x103
to 1.6 x 103 for white variety and 0.3 x 103 to 1.1 x103 for yellow
variety respectively. The Lactic acid bacterial count of 3.5x106 and
3.0x106 was recorded for the laboratory ogi while the commercially
prepared ogi ranged from 3.2x106 to 4.2x106 (white variety) and 3.0
x106 to 3.9 x106 (yellow). The presence of bacteria isolates from the
commercial and laboratory fermented ogi showed that Lactobacillus
sp, Leuconostoc sp and Citrobacter sp were present in all the
samples, Micrococcus sp and Klebsiella sp were isolated from Eke-
Okigwe and ABSU-up-gate markets varieties respectively, E. coli
and Staphylococcus sp were present in Eke-Okigwe and Nkwo-
Achara markets while Salmonella sp were isolated from the three
markets. Hence, there are chances of contracting food borne diseases
from commercially prepared ogi. Therefore, there is the need for
sanitary measures in the production of fermented cereals so as to
minimize the rate of food borne pathogens during processing and
storage.
Abstract: Due to the resultant leachate from waste
decomposition in landfills has polluter potential hundred times
greater than domestic sewage, this is considered a problem related to
the depreciation of environment requiring pre-disposal treatment.In
seeking to improve this situation, this project proposes the treatment
of landfill leachate using natural fibers intercropped with advanced
oxidation processes. The selected natural fibers were palm, coconut
and banana fiber.These materials give sustainability to the project
because, besides having adsorbent capacity, are often part of waste
discarded. The study was conducted in laboratory scale.In trials, the
effluents were characterized as Chemical Oxygen Demand (COD),
Turbidity and Color. The results indicate that is technically
promising since that there were extremely oxidative conditions, the
use of certain natural fibers in the reduction of pollutants in leachate
have been obtained results of COD removals between 67.9% and
90.9%, Turbidity between 88.0% and 99.7% and Color between
67.4% and 90.4%.The expectation generated is to continue evaluating
the association of efficiency of other natural fibers with other landfill
leachate treatment processes.