Abstract: Ceramic Waste Aggregates (CWAs) were made from
electric porcelain insulator wastes supplied from an electric power
company, which were crushed and ground to fine aggregate sizes. In
this study, to develop the CWA mortar as an eco–efficient, ground
granulated blast–furnace slag (GGBS) as a Supplementary
Cementitious Material (SCM) was incorporated. The water–to–binder
ratio (W/B) of the CWA mortars was varied at 0.4, 0.5, and 0.6. The
cement of the CWA mortar was replaced by GGBS at 20 and 40% by
volume (at about 18 and 37% by weight). Mechanical properties of
compressive and splitting tensile strengths, and elastic modulus were
evaluated at the age of 7, 28, and 91 days. Moreover, the chloride
ingress test was carried out on the CWA mortars in a 5.0% NaCl
solution for 48 weeks. The chloride diffusion was assessed by using an
electron probe microanalysis (EPMA). To consider the relation of the
apparent chloride diffusion coefficient and the pore size, the pore size
distribution test was also performed using a mercury intrusion
porosimetry at the same time with the EPMA. The compressive
strength of the CWA mortars with the GGBS was higher than that
without the GGBS at the age of 28 and 91 days. The resistance to the
chloride ingress of the CWA mortar was effective in proportion to the
GGBS replacement level.
Abstract: Live video streaming is one of the most widely used
service among end users, yet it is a big challenge for the network
operators in terms of quality. The only way to provide excellent
Quality of Experience (QoE) to the end users is continuous
monitoring of live video streaming. For this purpose, there are several
objective algorithms available that monitor the quality of the video in
a live stream. Subjective tests play a very important role in fine
tuning the results of objective algorithms. As human perception is
considered to be the most reliable source for assessing the quality of a
video stream subjective tests are conducted in order to develop more
reliable objective algorithms. Temporal impairments in a live video
stream can have a negative impact on the end users. In this paper we
have conducted subjective evaluation tests on a set of video
sequences containing temporal impairment known as frame freezing.
Frame Freezing is considered as a transmission error as well as a
hardware error which can result in loss of video frames on the
reception side of a transmission system. In our subjective tests, we
have performed tests on videos that contain a single freezing event
and also for videos that contain multiple freezing events. We have
recorded our subjective test results for all the videos in order to give a
comparison on the available No Reference (NR) objective
algorithms. Finally, we have shown the performance of no reference
algorithms used for objective evaluation of videos and suggested the
algorithm that works better. The outcome of this study shows the
importance of QoE and its effect on human perception. The results
for the subjective evaluation can serve the purpose for validating
objective algorithms.
Abstract: Nowadays, technological progress is one of the most
important components of economic growth and the efficiency of
R&D activities is particularly essential for countries. This study is an
attempt to analyze the R&D efficiencies of EU countries. The
indicators related to R&D efficiencies should be determined in
advance in order to use DEA. For this reason a list of input and
output indicators are derived from the literature review. Considering
the data availability, a final list is given for the numerical analysis for
future research.
Abstract: Significant attention has recently been paid to the
cross-cultural negotiations due to the growth of international
businesses. Despite the substantial body of literature examining the
influence of National Culture (NC) dimensions on negotiations, there
is a lack of studies comparing the influence of NC in Latin America
with a Western European countries, In particular, an extensive review
of the literature revealed that a contribution to knowledge would be
derived from the comparison of the influence of NC dimensions on
negotiations in UK and Venezuela. The primary data was collected
through qualitative interviews, to obtain an insight about the
perceptions and beliefs of Venezuelan and British business managers
about their negotiating styles. The findings of this study indicated
that NC has a great influence on the negotiating styles. In particular,
Venezuelan and British managers demonstrated to have opposed
negotiating styles, affecting the way they communicate, approach
people and their willingness to take risks.
Abstract: Transparent nickel doped cobalt sulfide was fabricated
on a SnO2:F electrode and tested as an efficient electrocatalyst and as
an alternative to the expensive platinum counter electrode. In order to
investigate how this electrode could affect the electrical
characteristics of a dye-sensitized solar cell, we manufactured cells
with the same TiO2 photoanode sensitized with dye (N719) and
employing the same quasi-solid electrolyte, altering only the counter
electrode used. The cells were electrically and electrochemically
characterized and it was observed that the ones with the Ni doped
CoS2 outperformed the efficiency of the cells with the Pt counter
electrode (3.76% and 3.44% respectively). Particularly, the higher
efficiency of the cells with the Ni doped CoS2 counter electrode (CE)
is mainly because of the enhanced photocurrent density which is
attributed to the enhanced electrocatalytic ability of the CE and the
low charge transfer resistance at the CE/electrolyte interface.
Abstract: This contribution presents a friction estimator for
industrial purposes which identifies Coulomb friction in a steering
system. The estimator only needs a few, usually known, steering
system parameters. Friction occurs on almost every mechanical
system and has a negative influence on high-precision position
control. This is demonstrated on a steering angle controller for highly
automated driving. In this steering system the friction induces limit
cycles which cause oscillating vehicle movement when the vehicle
follows a given reference trajectory. When compensating the friction
with the introduced estimator, limit cycles can be suppressed. This
is demonstrated by measurements in a series vehicle.
Abstract: The design of high pressure water jet based polishing
equipment and its fabrication conducted in this study is reported
herein, together with some preliminary test results for assessing its
applicability for HMA surface polishing. This study also provides
preliminary findings concerning the test variables, such as the
rotational speed, the water jet pressure, the abrasive agent used, and
the impact angel that were experimentally investigated in this study. The preliminary findings based on four trial tests (two on large
slab specimens and two on small size gyratory compacted
specimens), however, indicate that both friction and texture values
tend to increase with the polishing durations for two combinations of
pressure and rotation speed of the rotary deck. It seems that the more
polishing action the specimen is subjected to; the aggregate edges are
created such that the surface texture values are increased with the
accompanied increase in friction values. It may be of interest (but
which is outside the scope of this study) to investigate if the similar
trend exist for HMA prepared with aggregate source that is sand and
gravel.
Abstract: This study was conducted to determine sex
differentiation of laboratory reared Elm nymphalid (Nymphalis
polychloros Linnaeus, 1758) by examining the morphological
structure of pupal stage. Laboratory colony of elm nymphalid, reared
on pear leaves, was used to set up experiments. It was performed
with 5 replications having 8 pupae for each replication. Dorsal,
ventral and lateral parts of external morphological structures of pupae
were examined by Olympus SZX9 stereozoom microscope and
photographed. When fully grown, mature larvae wander the highest
part of the rearing cage and pupae were formed hanging by
cremaster. After completing prepupa stage about 1.5±0.3 days, they
all pupated. Pupal stage was completed at 24±1°C about 4.38±1.20
days. Pupal weights were 0.483±0.05 g in females and 0.392±0.08 g
(n=40) in males respectively. Pupal emergence rate was 95%, with
22 females and 16 males. Examinations of ventral parts of 8th, 9th,
and 10th abdominal segments revealed that anal opening were found
at 10th abdominal segment in both sexes, 3 lumps were determined at
9th abdominal segments then the specific opening structure at 8th
segment was only found on female pupae.
Abstract: These Monolayer and multilayer coatings of CrN and
AlCrN deposited on 100Cr6 (AISI 52100) substrate by PVD
magnetron sputtering system. The microstructures of the coatings
were characterized using atomic force microscopy (AFM). The AFM
analysis revealed the presence of domes and craters that are
uniformly distributed over all surfaces of the various layers.
Nanoindentation measurement of CrN coating showed maximum
hardness (H) and modulus (E) of 14 GPa and 190 GPa, respectively.
The measured H and E values of AlCrN coatings were found to be 30
GPa and 382 GPa, respectively. The improved hardness in both the
coatings was attributed mainly to a reduction in crystallite size and
decrease in surface roughness. The incorporation of Al into the CrN
coatings has improved both hardness and Young’s modulus.
Abstract: The effects of flame-holder position, the ratio of flame
holder diameter to combustion chamber diameter and injection angle
on fuel propulsive droplets sizing and effective mass fraction have
been studied by a cold flow. We named the mass of fuel vapor inside
the flammability limit as the effective mass fraction. An empty
cylinder as well as a flame-holder which are a simulator for duct
combustion has been considered. The airflow comes into the cylinder
from one side and injection operation will be done by four nozzles
which are located on the entrance of cylinder. To fulfill the
calculations a modified version of KIVA-3V code which is a
transient, three-dimensional, multiphase, multi component code for
the analysis of chemically reacting flows with sprays, is used.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Distillery spentwash contains high chemical oxygen
demand (COD), biological oxygen demand (BOD), color, total
dissolved solids (TDS) and other contaminants even after biological
treatment. The effluent can’t be discharged as such in the surface
water bodies or land without further treatment. Reverse osmosis (RO)
treatment plants have been installed in many of the distilleries at
tertiary level in many of the distilleries in India, but are not properly
working due to fouling problem which is caused by the presence of
high concentration of organic matter and other contaminants in
biologically treated spentwash. In order to make the membrane
treatment a proven and reliable technology, proper pre-treatment is
mandatory. In the present study, ultra-filtration (UF) for pretreatment
of RO at tertiary stage has been performed. Operating
parameters namely initial pH (pHo: 2–10), trans-membrane pressure
(TMP: 4-20 bars) and temperature (T: 15-43°C) were used for
conducting experiments with UF system. Experiments were
optimized at different operating parameters in terms of COD, color,
TDS and TOC removal by using response surface methodology
(RSM) with central composite design. The results showed that
removal of COD, color and TDS was 62%, 93.5% and 75.5%
respectively, with UF, at optimized conditions with increased
permeate flux from 17.5 l/m2/h (RO) to 38 l/m2/h (UF-RO). The
performance of the RO system was greatly improved both in term of
pollutant removal as well as water recovery.
Abstract: Biodiesel production from vegetable oil will produce
glycerol as by-product about 10% of the biodiesel production. The
amount of glycerol that was produced needed alternative way to
handling immediately so as to not become the waste that polluted
environment. One of the solutions was to process glycerol to
polyglycidyl nitrate (PGN). PGN is synthesized from glycerol by
three-step reactions i.e. nitration of glycerol, cyclization of 13-
dinitroglycerine and polymerization of glycosyl nitrate. Optimum
condition of nitration of glycerol with nitric acid has not been known.
Thermodynamic feasibility should be done before run experiments in
the laboratory. The aim of this study was to determine the parameters
those affect nitration of glycerol and nitric acid and chose the
operation condition. Many parameters were simulated to verify its
possibility to experiment under conditions which would get the
highest conversion of 1, 3-dinitroglycerine and which was the ideal
condition to get it. The parameters that need to be studied to obtain
the highest conversion of 1, 3-dinitroglycerine were mol ratio of
nitric acid/glycerol, reaction temperature, mol ratio of
glycerol/dichloromethane and pressure. The highest conversion was
obtained in the range of mol ratio of nitric acid /glycerol between 2/1
– 5/1, reaction temperature of 5-25oC and pressure of 1 atm. The
parameters that need to be studied further to obtain the highest
conversion of 1.3 DNG are mol ratio of nitric acid/glycerol and
reaction temperature.
Abstract: The aim of the present study is to detect the chaotic
behavior in monetary economic relevant dynamical system. The
study employs three different forms of Taylor rules: current, forward,
and backward looking. The result suggests the existence of the
chaotic behavior in all three systems. In addition, the results strongly
represent that using expectations in policy rule especially rational
expectation hypothesis can increase complexity of the system and
leads to more chaotic behavior.
Abstract: We apply the non-parametric, unconditional,
hyperbolic order-α quantile estimator to appraise the relative
efficiency of Microfinance Institutions in Africa in terms of outreach.
Our purpose is to verify if these institutions, which must constantly
try to strike a compromise between their social role and financial
sustainability are operationally efficient.
Using data on African MFIs extracted from the Microfinance
Information eXchange (MIX) database and covering the 2004 to
2006 periods, we find that more efficient MFIs are also the most
profitable. This result is in line with the view that social performance
is not in contradiction with the pursuit of excellent financial
performance. Our results also show that large MFIs in terms of asset
and those charging the highest fees are not necessarily the most
efficient.
Abstract: Superabsorbent polymers received much attention and
are used in many fields because of their superior characters to
traditional absorbents, e.g., sponge and cotton. So, it is very
important but challenging to prepare highly and fast-swelling
superabsorbents. A reliable, efficient and low-cost technique for
removing heavy metal ions from wastewater is the adsorption using
bio-adsorbents obtained from biological materials, such as
polysaccharides-based hydrogels superabsorbents. In this study, novel multi-functional superabsorbent composites
type semi-interpenetrating polymer networks (Semi-IPNs) were
prepared via graft polymerization of acrylamide onto chitosan
backbone in presence of gelatin, CTS-g-PAAm/Ge, using potassium
persulfate and N,N’-methylene bisacrylamide as initiator and
crosslinker, respectively. These hydrogels were also partially
hydrolyzed to achieve superabsorbents with ampholytic properties
and uppermost swelling capacity. The formation of the grafted
network was evidenced by Fourier Transform Infrared Spectroscopy
(ATR-FTIR) and Thermogravimetric Analysis (TGA). The porous
structures were observed by Scanning Electron Microscope (SEM).
From TGA analysis, it was concluded that the incorporation of the Ge
in the CTS-g-PAAm network has marginally affected its thermal
stability. The effect of gelatin content on the swelling capacities of
these superabsorbent composites was examined in various media
(distilled water, saline and pH-solutions). The water absorbency was
enhanced by adding Ge in the network, where the optimum value was
reached at 2 wt. % of Ge. Their hydrolysis has not only greatly
optimized their absorption capacity but also improved the swelling
kinetic.These materials have also showed reswelling ability. We
believe that these super-absorbing materials would be very effective
for the adsorption of harmful metal ions from wastewater.
Abstract: High Voltage Direct Current (HVDC) power
transmission is employed to move large amounts of electric power.
There are several possibilities to enhance the transient stability in a
power system. One adequate option is by using the high
controllability of the HVDC if HVDC is available in the system. This
paper presents a control technique for HVDC to enhance the transient
stability. The strategy controls the power through the HVDC to help
make the system more transient stable during disturbances. Loss of
synchronism is prevented by quickly producing sufficient
decelerating energy to counteract accelerating energy gained during.
In this study, the power flow in the HVDC link is modulated with the
addition of an auxiliary signal to the current reference of the rectifier
firing angle controller. This modulation control signal is derived from
speed deviation signal of the generator utilizing a PD controller; the
utilization of a PD controller is suitable because it has the property of
fast response. The effectiveness of the proposed controller is
demonstrated with a SMIB test system.
Abstract: It is necessary to predict a fatigue crack propagation
life for estimation of structural integrity. Because of an uncertainty
and a randomness of a structural behavior, it is also required to
analyze stochastic characteristics of the fatigue crack propagation life
at a specified fatigue crack size. The essential purpose of this study is to find the effect of load ratio
on probability distribution of the fatigue crack propagation life at a
specified grown crack size and to confirm the good probability
distribution in magnesium alloys under various fatigue load ratio
conditions. To investigate a stochastic crack growth behavior, fatigue
crack propagation experiments are performed in laboratory air under
several conditions of fatigue load ratio using AZ31. By Anderson-Darling test, a goodness-of-fit test for probability
distribution of the fatigue crack propagation life is performed. The
effect of load ratio on variability of fatigue crack propagation life is
also investigated.
Abstract: Research Objectives: The roles and activities of
Human Resource Management (HRM) have changed a lot in the past
years. Driven by a changing environment and therefore new business
requirements, the scope of human resource (HR) activities has
widened. The extent to which these activities should focus on
strategic issues to support the long term success of a company has
been discussed in science for many years. As many economies of
Central and Eastern Europe (CEE) experienced a phase of transition
after the socialist era and are now recovering from the 2008 global
crisis it is needed to examine the current state of HR positioning.
Furthermore a trend in HR work developing from rather
administrative units to being strategic partners of management can be
noticed. This leads to the question of better understanding the
underlying competencies which are necessary to support
organisations. This topic was addressed by the international study
“HR Competencies in international comparison”. The quantitative
survey was conducted by the Institute for Human Resources &
Organisation of FHWien University of Applied Science of WKW (A)
in cooperation with partner universities in the countries Bosnia-
Herzegovina, Croatia, Serbia and Slovenia. Methodology: Using the
questionnaire developed by Dave Ulrich we tested whether the HR
Competency model can be used for Austria, Bosnia and Herzegovina,
Croatia, Serbia and Slovenia. After performing confirmatory and
exploratory factor analysis for the whole data set containing all five
countries we could clearly distinguish between four competencies. In
a further step our analysis focused on median and average
comparisons between the HR competency dimensions. Conclusion:
Our literature review, in alignment with other studies, shows a
relatively rapid pace of development of HR Roles and HR
Competencies in BCSS in the past decades. Comparing data from
BCSS and Austria we still can notice that regards strategic orientation
there is a lack in BCSS countries, thus competencies are not as
developed as in Austria. This leads us to the tentative conclusion that
HR has undergone a rapid change but is still in a State of Transition
from being a rather administrative unit to performing the role of a
strategic partner.
Abstract: The article describes the effect of the replacement of
the used reference coordinate system in the georeferencing of an old
map of Europe. The map was georeferenced into three types of
projection – the equal-area conic (original cartographic projection),
cylindrical Plate Carrée and cylindrical Mercator map projection. The
map was georeferenced by means of the affine and the second-order
polynomial transformation. The resulting georeferenced raster
datasets from the Plate Carrée and Mercator projection were
projected into the equal-area conic projection by means of projection
equations. The output is the comparison of drawn graphics, the
magnitude of standard deviations for individual projections and types
of transformation.