Abstract: Heart disease (HD) is a major cause of morbidity and mortality in the modern society. Medical diagnosis is an important but complicated task that should be performed accurately and efficiently and its automation would be very useful. All doctors are unfortunately not equally skilled in every sub specialty and they are in many places a scarce resource. A system for automated medical diagnosis would enhance medical care and reduce costs. In this paper, a new approach based on coactive neuro-fuzzy inference system (CANFIS) was presented for prediction of heart disease. The proposed CANFIS model combined the neural network adaptive capabilities and the fuzzy logic qualitative approach which is then integrated with genetic algorithm to diagnose the presence of the disease. The performances of the CANFIS model were evaluated in terms of training performances and classification accuracies and the results showed that the proposed CANFIS model has great potential in predicting the heart disease.
Abstract: The present study deals with the modeling and simulation of flow through an annular reactor at different hydrodynamic conditions using computational fluid dynamics (CFD) to investigate the flow behavior. CFD modeling was utilized to predict velocity distribution and average velocity in the annular geometry. The results of CFD simulations were compared with the mathematically derived equations and already developed correlations for validation purposes. CFD modeling was found suitable for predicting the flow characteristics in annular geometry under laminar flow conditions. It was observed that CFD also provides local values of the parameters of interest in addition to the average values for the simulated geometry.
Abstract: This paper examines the use of mechanical aerator for
oxidation-ditch process. The rotor, which controls the aeration, is the
main component of the aeration process. Therefore, the objective of
this study is to find out the variations in overall oxygen transfer
coefficient (KLa) and aeration efficiency (AE) for different
configurations of aerator by varying the parameters viz. speed of
aerator, depth of immersion, blade tip angles so as to yield higher
values of KLa and AE. Six different configurations of aerator were
developed and fabricated in the laboratory and were tested for abovementioned
parameters. The curved blade rotor (CBR) emerged as a
potential aerator with blade tip angle of 47°.
The mathematical models are developed for predicting the
behaviour of CBR w.r.t kLa and power. In laboratory studies, the
optimum value of KLa and AE were observed to be 10.33 h-1 and
2.269 kg O2/ kWh.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: Diabetes Mellitus is a chronic metabolic disorder, where the improper management of the blood glucose level in the diabetic patients will lead to the risk of heart attack, kidney disease and renal failure. This paper attempts to enhance the diagnostic accuracy of the advancing blood glucose levels of the diabetic patients, by combining principal component analysis and wavelet neural network. The proposed system makes separate blood glucose prediction in the morning, afternoon, evening and night intervals, using dataset from one patient covering a period of 77 days. Comparisons of the diagnostic accuracy with other neural network models, which use the same dataset are made. The comparison results showed overall improved accuracy, which indicates the effectiveness of this proposed system.
Abstract: With the hardware technology advancing, the cost of
storing is decreasing. Thus there is an urgent need for new techniques
and tools that can intelligently and automatically assist us in
transferring this data into useful knowledge. Different techniques of
data mining are developed which are helpful for handling these large
size databases [7]. Data mining is also finding its role in the field of
biotechnology. Pedigree means the associated ancestry of a crop
variety. Genetic diversity is the variation in the genetic composition
of individuals within or among species. Genetic diversity depends
upon the pedigree information of the varieties. Parents at lower
hierarchic levels have more weightage for predicting genetic
diversity as compared to the upper hierarchic levels. The weightage
decreases as the level increases. For crossbreeding, the two varieties
should be more and more genetically diverse so as to incorporate the
useful characters of the two varieties in the newly developed variety.
This paper discusses the searching and analyzing of different possible
pairs of varieties selected on the basis of morphological characters,
Climatic conditions and Nutrients so as to obtain the most optimal
pair that can produce the required crossbreed variety. An algorithm
was developed to determine the genetic diversity between the
selected wheat varieties. Cluster analysis technique is used for
retrieving the results.
Abstract: Lateral expansion is a factor defining the level of
confinement in reinforced concrete columns. Therefore, predicting
the lateral strain relationship with axial strain becomes an important
issue. Measuring lateral strains in experiments is difficult and only
few report experimental lateral strains. Among the existing analytical
formulations, two recent models are compared with available test
results in this paper with shortcomings highlighted. A new analytical
model is proposed here for lateral strain axial strain relationship and
is based on the supposition that the concrete behaves linear elastic in
the early stages of loading and then nonlinear hardening up to the
peak stress and then volumetric expansion. The proposal for the
lateral strain axial strain relationship after the peak stress is mainly
based on the hypothesis that the plastic lateral strain varies linearly
with the plastic axial strain and it is shown that this is related to the
lateral confinement level.
Abstract: Predicting protein-protein interactions represent a key step in understanding proteins functions. This is due to the fact that proteins usually work in context of other proteins and rarely function alone. Machine learning techniques have been applied to predict protein-protein interactions. However, most of these techniques address this problem as a binary classification problem. Although it is easy to get a dataset of interacting proteins as positive examples, there are no experimentally confirmed non-interacting proteins to be considered as negative examples. Therefore, in this paper we solve this problem as a one-class classification problem using one-class support vector machines (SVM). Using only positive examples (interacting protein pairs) in training phase, the one-class SVM achieves accuracy of about 80%. These results imply that protein-protein interaction can be predicted using one-class classifier with comparable accuracy to the binary classifiers that use artificially constructed negative examples.
Abstract: Prediction of highly non linear behavior of suspended
sediment flow in rivers has prime importance in the field of water
resources engineering. In this study the predictive performance of
two Artificial Neural Networks (ANNs) namely, the Radial Basis
Function (RBF) Network and the Multi Layer Feed Forward (MLFF)
Network have been compared. Time series data of daily suspended
sediment discharge and water discharge at Pari River was used for
training and testing the networks. A number of statistical parameters
i.e. root mean square error (RMSE), mean absolute error (MAE),
coefficient of efficiency (CE) and coefficient of determination (R2)
were used for performance evaluation of the models. Both the models
produced satisfactory results and showed a good agreement between
the predicted and observed data. The RBF network model provided
slightly better results than the MLFF network model in predicting
suspended sediment discharge.
Abstract: In this paper, an ultrasonic technique is proposed to
predict oil content in a fresh palm fruit. This is accomplished by
measuring the attenuation based on ultrasonic transmission mode.
Several palm fruit samples with known oil content by Soxhlet
extraction (ISO9001:2008) were tested with our ultrasonic
measurement. Amplitude attenuation data results for all palm samples
were collected. The Feedforward Neural Networks (FNNs) are
applied to predict the oil content for the samples. The Root Mean
Square Error (RMSE) and Mean Absolute Error (MAE) of the FNN
model for predicting oil content percentage are 7.6186 and 5.2287
with the correlation coefficient (R) of 0.9193.
Abstract: This study deals with the experimental investigation
and theoretical modeling of Semi crystalline polymeric materials with
a rubbery amorphous phase (HDPE) subjected to a uniaxial cyclic
tests with various maximum strain levels, even at large deformation.
Each cycle is loaded in tension up to certain maximum strain and
then unloaded down to zero stress with N number of cycles. This
work is focuses on the measure of the volume strain due to the
phenomena of damage during this kind of tests. On the basis of
thermodynamics of relaxation processes, a constitutive model for
large strain deformation has been developed, taking into account the
damage effect, to predict the complex elasto-viscoelastic-viscoplastic
behavior of material. A direct comparison between the model
predictions and the experimental data show that the model accurately
captures the material response. The model is also capable of
predicting the influence damage causing volume variation.
Abstract: Gas Metal Arc Welding (GMAW) processes is an
important joining process widely used in metal fabrication
industries. This paper addresses modeling and optimization of this
technique using a set of experimental data and regression analysis.
The set of experimental data has been used to assess the influence
of GMAW process parameters in weld bead geometry. The
process variables considered here include voltage (V); wire feed
rate (F); torch Angle (A); welding speed (S) and nozzle-to-plate
distance (D). The process output characteristics include weld bead
height, width and penetration. The Taguchi method and regression
modeling are used in order to establish the relationships between
input and output parameters. The adequacy of the model is
evaluated using analysis of variance (ANOVA) technique. In the
next stage, the proposed model is embedded into a Simulated
Annealing (SA) algorithm to optimize the GMAW process
parameters. The objective is to determine a suitable set of process
parameters that can produce desired bead geometry, considering
the ranges of the process parameters. Computational results prove
the effectiveness of the proposed model and optimization
procedure.
Abstract: The gases generated in oil filled transformers can be
used for qualitative determination of incipient faults. The Dissolved
Gas Analysis has been widely used by utilities throughout the world
as the primarily diagnostic tool for transformer maintenance. In this
paper, various Artificial Intelligence Techniques that have been used
by the researchers in the past have been reviewed, some conclusions
have been drawn and a sequential hybrid system has been proposed.
The synergy of ANN and FIS can be a good solution for reliable
results for predicting faults because one should not rely on a single
technology when dealing with real–life applications.
Abstract: A predictive clustering hybrid regression (pCHR)
approach was developed and evaluated using dataset from H2-
producing sucrose-based bioreactor operated for 15 months. The aim
was to model and predict the H2-production rate using information
available about envirome and metabolome of the bioprocess. Selforganizing
maps (SOM) and Sammon map were used to visualize the
dataset and to identify main metabolic patterns and clusters in
bioprocess data. Three metabolic clusters: acetate coupled with other
metabolites, butyrate only, and transition phases were detected. The
developed pCHR model combines principles of k-means clustering,
kNN classification and regression techniques. The model performed
well in modeling and predicting the H2-production rate with mean
square error values of 0.0014 and 0.0032, respectively.
Abstract: Studying alternative raw materials for biodiesel production is of major importance. The use of mixtures with incorporation of wastes is an environmental friendly alternative and might reduce biodiesel production costs. The objective of the present work was: (i) to study biodiesel production using waste frying oil mixed with pork lard and (ii) to understand how mixture composition influences biodiesel quality. Biodiesel was produced by transesterification and quality was evaluated through determination of several parameters according to EN 14214. The weight fraction of lard in the mixture varied from 0 to 1 in 0.2 intervals. Biodiesel production yields varied from 81.7 to 88.0 (wt%), the lowest yields being the ones obtained using waste frying oil and lard alone as raw materials. The obtained products fulfilled most of the determined quality specifications according to European biodiesel quality standard EN 14214. Minimum purity (96.5 wt%) was closely obtained when waste frying oil was used alone and when 0.2% of lard was incorporated in the raw material (96.3 wt%); however, it ranged from 93.9 to 96.3 (wt%) being always close to the limit. From the evaluation of the influence of mixture composition in biodiesel quality, it was possible to establish a model to be used for predicting some parameters of biodiesel resulting from mixtures of waste frying oil with lard when different lard contents are used.
Abstract: Investigation of soil properties like Cation Exchange
Capacity (CEC) plays important roles in study of environmental
reaserches as the spatial and temporal variability of this property
have been led to development of indirect methods in estimation of
this soil characteristic. Pedotransfer functions (PTFs) provide an
alternative by estimating soil parameters from more readily available
soil data. 70 soil samples were collected from different horizons of
15 soil profiles located in the Ziaran region, Qazvin province, Iran.
Then, multivariate regression and neural network model (feedforward
back propagation network) were employed to develop a
pedotransfer function for predicting soil parameter using easily
measurable characteristics of clay and organic carbon. The
performance of the multivariate regression and neural network model
was evaluated using a test data set. In order to evaluate the models,
root mean square error (RMSE) was used. The value of RMSE and
R2 derived by ANN model for CEC were 0.47 and 0.94 respectively,
while these parameters for multivariate regression model were 0.65
and 0.88 respectively. Results showed that artificial neural network
with seven neurons in hidden layer had better performance in
predicting soil cation exchange capacity than multivariate regression.
Abstract: In this paper, we propose an easily computable proximity index for predicting voltage collapse of a load bus using only measured values of the bus voltage and power; Using these measurements a polynomial of fourth order is obtained by using LES estimation algorithms. The sum of the absolute values of the polynomial coefficient gives an idea of the critical bus. We demonstrate the applicability of our proposed method on 6 bus test system. The results obtained verify its applicability, as well as its accuracy and the simplicity. From this indicator, it is allowed to predict the voltage instability or the proximity of a collapse. Results obtained by the PV curve are compared with corresponding values by QV curves and are observed to be in close agreement.
Abstract: The problems associated with wind predictions of
WAsP model in complex terrain are already the target of several
studies in the last decade. In this paper, the influence of surrounding
orography on accuracy of wind data analysis of a train is
investigated. For the case study, a site with complex surrounding
orography is considered. This site is located in Manjil, one of the
windiest cities of Iran. For having precise evaluation of wind regime
in the site, one-year wind data measurements from two metrological
masts are used. To validate the obtained results from WAsP, the
cross prediction between each mast is performed. The analysis
reveals that WAsP model can estimate the wind speed behavior
accurately. In addition, results show that this software can be used
for predicting the wind regime in flat sites with complex surrounding
orography.
Abstract: This paper deals with heterogeneous autoregressive
models of realized volatility (HAR-RV models) on high-frequency
data of stock indices in the USA. Its aim is to capture the behavior of
three groups of market participants trading on a daily, weekly and
monthly basis and assess their role in predicting the daily realized
volatility. The benefits of this work lies mainly in the application of
heterogeneous autoregressive models of realized volatility on stock
indices in the USA with a special aim to analyze an impact of the
global financial crisis on applied models forecasting performance.
We use three data sets, the first one from the period before the global
financial crisis occurred in the years 2006-2007, the second one from
the period when the global financial crisis fully hit the U.S. financial
market in 2008-2009 years, and the last period was defined over
2010-2011 years. The model output indicates that estimated realized
volatility in the market is very much determined by daily traders and
in some cases excludes the impact of those market participants who
trade on monthly basis.
Abstract: In this article, a simulation method called the Homotopy Perturbation Method (HPM) is employed in the steady flow of a Walter's B' fluid in a vertical channel with porous wall. We employed Homotopy Perturbation Method to derive solution of a nonlinear form of equation obtained from exerting similarity transforming to the ordinary differential equation gained from continuity and momentum equations of this kind of flow. The results obtained from the Homotopy Perturbation Method are then compared with those from the Runge–Kutta method in order to verify the accuracy of the proposed method. The results show that the Homotopy Perturbation Method can achieve good results in predicting the solution of such problems. Ultimately we use this solution to obtain the other terms of velocities and physical discussion about it.