Abstract: This paper is an extension of a previous work where a diagonally implicit harmonic balance method was developed and applied to simulate oscillatory motions of pitching airfoil and wing. A more detailed study on the accuracy, convergence, and the efficiency of the method is carried out in the current paperby varying the number of harmonics in the solution approximation. As the main advantage of the method is itsusage for the design optimization of the unsteady problems, its application to more practical case of rotor flow analysis during forward flight is carried out and compared with flight test data and time-accurate computation results.
Abstract: Clustering algorithms are attractive for the task of class identification in spatial databases. However, the application to large spatial databases rises the following requirements for clustering algorithms: minimal requirements of domain knowledge to determine the input parameters, discovery of clusters with arbitrary shape and good efficiency on large databases. The well-known clustering algorithms offer no solution to the combination of these requirements. In this paper, a density based clustering algorithm (DCBRD) is presented, relying on a knowledge acquired from the data by dividing the data space into overlapped regions. The proposed algorithm discovers arbitrary shaped clusters, requires no input parameters and uses the same definitions of DBSCAN algorithm. We performed an experimental evaluation of the effectiveness and efficiency of it, and compared this results with that of DBSCAN. The results of our experiments demonstrate that the proposed algorithm is significantly efficient in discovering clusters of arbitrary shape and size.
Abstract: Stormwater wetlands have been mainly designed in an
empirical approach for water quality improvement, with little
quantitative understanding of the internal microbial processes. This
study investigated into heterotrophic bacterial production rate,
heterotrophic bacterial mineralization percentage, and algal biomass
in hypertrophic and eutrophic surface flow stormwater wetlands.
Compared to a nearby wood leachate treatment wetland, the
stormwater wetlands had much higher chlorophyll-a concentrations.
The eutrophic stormwater wetland had improved water quality,
whereas the hypertrophic stormwater wetland had degraded water
quality. Heterotrophic bacterial activities in water were limited in the
stormwater wetlands due to competition of algal growth for nutrients.
The relative contribution of biofilms to the overall heterotrophic
activities was higher in the stormwater wetlands than that in the wood
leachate treatment wetland.
Abstract: Theobjective of this study was to evaluate the optimal
treatment condition of Fenton oxidation process to removal
contaminant in soil slurry contaminated by petroleum hydrocarbons.
This research studied somefactors that affect the removal efficiency
of petroleum hydrocarbons in soil slurry including molar ratio of
hydrogen peroxide (H2O2) to ferrous ion(Fe2+), pH condition and
reaction time.The resultsdemonstrated that the optimum condition
was that the molar ratio of H2O2:Fe3+ was 200:1,the pHwas 4.0and
the rate of reaction was increasing rapidly from starting point to 7th
hour and destruction kinetic rate (k) was 0.24 h-1. Approximately
96% of petroleum hydrocarbon was observed(initialtotal petroleum
hydrocarbon (TPH) concentration = 70±7gkg-1)
Abstract: This work discusses an innovative methodology for
deployment of service quality characteristics. Four groups of organizational features that may influence the quality of services are identified: human resource, technology, planning, and organizational
relationships. A House of Service Quality (HOSQ) matrix is built to
extract the desired improvement in the service quality characteristics
and to translate them into a hierarchy of important organizational
features. The Mean Square Error (MSE) criterion enables the
pinpointing of the few essential service quality characteristics to be
improved as well as selection of the vital organizational features. The
method was implemented in an engineering supply enterprise and
provides useful information on its vital service dimensions.
Abstract: Narratives are invaluable assets of human lives. Due to
the distinct features of narratives, they are useful for supporting human
reasoning processes. However, many useful narratives become
residuals in organizations or human minds nowadays. Researchers
have contributed effort to investigate and improve narrative generation
processes. This paper attempts to contemplate essential components in
narratives and explore a computational approach to acquire and extract
knowledge to generate narratives. The methodology and significant
benefit for decision support are presented.
Abstract: An algorithm for estimating the disparity of objects of
interest is proposed. This algorithm uses image shifting and
overlapping area to estimate the disparity value; thereby depth of the
objects of interest can be obtained. The algorithm is able to perform
at different levels of accuracy. However, as the accuracy increases
the processing speed decreases. The algorithm is tested with static
stereo images and sequence of stereo images. The experimental
results are presented in this paper.
Abstract: At present, the tendency to implement the conditionbased
maintenance (CBM), which allows the optimization of the
expenses for equipment monitoring, is more and more evident; also,
the transformer substations with remote monitoring are increasingly
used. This paper reviews all the advantages of the on-line monitoring
and presents an equipment for on-line monitoring of bushings, which
is the own contribution of specialists who are the authors of this
paper. The paper presents a study of the temperature field, using the
finite element method. For carrying out this study, the 3D modelling
of the above mentioned bushing was performed. The analysis study is
done taking into account the extreme thermal stresses, focusing at the
level of the first cooling wing section of the ceramic insulator. This
fact enables to justify the tanδ variation in time, depending on the
transformer loading and the environmental conditions. With a view
to reducing the variation of dielectric losses in bushing insulation, the
use of ferrofuids instead of mineral oils is proposed.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: Ovshinsky initiated scientific research in the field of
amorphous and disordered materials that continues to this day. The
Ovshinsky Effect where the resistance of thin GST films is
significantly reduced upon the application of low voltage is of
fundamental importance in phase-change - random access memory
(PC-RAM) devices.GST stands for GdSbTe chalcogenide type
glasses.However, the Ovshinsky Effect is not without controversy.
Ovshinsky thought the resistance of GST films is reduced by the
redistribution of charge carriers; whereas, others at that time including
many PC-RAM researchers today argue that the GST resistance
changes because the GST amorphous state is transformed to the
crystalline state by melting, the heat supplied by external heaters. In
this controversy, quantum mechanics (QM) asserts the heat capacity of
GST films vanishes, and therefore melting cannot occur as the heat
supplied cannot be conserved by an increase in GST film
temperature.By precluding melting, QM re-opens the controversy
between the melting and charge carrier mechanisms. Supporting
analysis is presented to show that instead of increasing GST film
temperature, conservation proceeds by the QED induced creation of
photons within the GST film, the QED photons confined by TIR. QED
stands for quantum electrodynamics and TIR for total internal
reflection. The TIR confinement of QED photons is enhanced by the
fact the absorbedheat energy absorbed in the GST film is concentrated
in the TIR mode because of their high surface to volume ratio. The
QED photons having Planck energy beyond the ultraviolet produce
excitons by the photoelectric effect, the electrons and holes of which
reduce the GST film resistance.
Abstract: In this paper a data miner based on the learning
automata is proposed and is called LA-miner. The LA-miner extracts
classification rules from data sets automatically. The proposed
algorithm is established based on the function optimization using
learning automata. The experimental results on three benchmarks
indicate that the performance of the proposed LA-miner is
comparable with (sometimes better than) the Ant-miner (a data miner
algorithm based on the Ant Colony optimization algorithm) and CNZ
(a well-known data mining algorithm for classification).
Abstract: Statistical selection procedures are used to select the
best simulated system from a finite set of alternatives. In this paper,
we present a procedure that can be used to select the best system
when the number of alternatives is large. The proposed procedure
consists a combination between Ranking and Selection, and Ordinal
Optimization procedures. In order to improve the performance of Ordinal
Optimization, Optimal Computing Budget Allocation technique
is used to determine the best simulation lengths for all simulation
systems and to reduce the total computation time. We also argue
the effect of increment in simulation samples for the combined
procedure. The results of numerical illustration show clearly the effect
of increment in simulation samples on the proposed combination of
selection procedure.
Abstract: There is a growing body of evidence to support the
proposition of product take back for remanufacturing particularly
within the context of Extended Producer Responsibility (EPR).
Remanufacturing however presents challenges unlike that of
traditional manufacturing environments due to its high levels of
uncertainty which may further distract organizations from
considering its potential benefits. This paper presents a novel
modeling approach for evaluating the uncertainty of part failures
within the remanufacturing process and its impact on economic and
environmental performance measures. This paper presents both the
theoretical modeling approach and an example of its use in
application.
Abstract: We present a genetic algorithm application to the problem of object registration (i.e., object detection, localization and recognition) in a class of medical images containing various types of blood cells. The genetic algorithm approach taken here is seen to be most appropriate for this type of image, due to the characteristics of the objects. Successful cell registration results on real life microscope images of blood cells show the potential of the proposed approach.
Abstract: Adhesion strength of exterior or interior coating of
steel pipes is too important. Increasing of coating adhesion on
surfaces can increase the life time of coating, safety factor of
transmitting line pipe and decreasing the rate of corrosion and costs.
Preparation of steel pipe surfaces before doing the coating process is
done by shot and grit blasting. This is a mechanical way to do it.
Some effective parameters on that process, are particle size of
abrasives, distance to surface, rate of abrasive flow, abrasive physical
properties, shapes, selection of abrasive, kind of machine and its
power, standard of surface cleanness degree, roughness, time of
blasting and weather humidity. This search intended to find some
better conditions which improve the surface preparation, adhesion
strength and corrosion resistance of coating. So, this paper has
studied the effect of varying abrasive flow rate, changing the
abrasive particle size, time of surface blasting on steel surface
roughness and over blasting on it by using the centrifugal blasting
machine. After preparation of numbers of steel samples (according to
API 5L X52) and applying epoxy powder coating on them, to
compare strength adhesion of coating by Pull-Off test. The results
have shown that, increasing the abrasive particles size and flow rate,
can increase the steel surface roughness and coating adhesion
strength but increasing the blasting time can do surface over blasting
and increasing surface temperature and hardness too, change,
decreasing steel surface roughness and coating adhesion strength.
Abstract: Guard channels improve the probability of successful
handoffs by reserving a number of channels exclusively for handoffs.
This concept has the risk of underutilization of radio spectrum due to
the fact that fewer channels are granted to originating calls even if
these guard channels are not always used, when originating calls are
starving for the want of channels. The penalty is the reduction of
total carried traffic. The optimum number of guard channels can help
reduce this problem. This paper presents fuzzy logic based guard
channel scheme wherein guard channels are reorganized on the basis
of traffic density, so that guard channels are provided on need basis.
This will help in incorporating more originating calls and hence high
throughput of the radio spectrum
Abstract: In this paper, some problem formulations of dynamic object parameters recovery described by non-autonomous system of ordinary differential equations with multipoint unshared edge conditions are investigated. Depending on the number of additional conditions the problem is reduced to an algebraic equations system or to a problem of quadratic programming. With this purpose the paper offers a new scheme of the edge conditions transfer method called by conditions shift. The method permits to get rid from differential links and multipoint unshared initially-edge conditions. The advantage of the proposed approach is concluded by capabilities of reduction of a parametric identification problem to essential simple problems of the solution of an algebraic system or quadratic programming.
Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: In this work, we consider the number of integer solutions
of Diophantine equation D : y2 - 2yx - 3 = 0 over Z and
also over finite fields Fp for primes p ≥ 5. Later we determine the
number of rational points on curves Ep : y2 = Pp(x) = yp
1 + yp
2
over Fp, where y1 and y2 are the roots of D. Also we give a formula
for the sum of x- and y-coordinates of all rational points (x, y) on
Ep over Fp.
Abstract: This paper presents a VLSI design approach of a highspeed
and real-time 2-D Discrete Wavelet Transform computing. The
proposed architecture, based on new and fast convolution approach,
reduces the hardware complexity in addition to reduce the critical
path to the multiplier delay. Furthermore, an advanced twodimensional
(2-D) discrete wavelet transform (DWT)
implementation, with an efficient memory area, is designed to
produce one output in every clock cycle. As a result, a very highspeed
is attained. The system is verified, using JPEG2000
coefficients filters, on Xilinx Virtex-II Field Programmable Gate
Array (FPGA) device without accessing any external memory. The
resulting computing rate is up to 270 M samples/s and the (9,7) 2-D
wavelet filter uses only 18 kb of memory (16 kb of first-in-first-out
memory) with 256×256 image size. In this way, the developed design
requests reduced memory and provide very high-speed processing as
well as high PSNR quality.