Abstract: Directional over current relays (DOCR) are commonly used in power system protection as a primary protection in distribution and sub-transmission electrical systems and as a secondary protection in transmission systems. Coordination of protective relays is necessary to obtain selective tripping. In this paper, an approach for efficiency reduction of DOCRs nonlinear optimum coordination (OC) is proposed. This was achieved by modifying the objective function and relaxing several constraints depending on the four constraints classification, non-valid, redundant, pre-obtained and valid constraints. According to this classification, the far end fault effect on the objective function and constraints, and in consequently on relay operating time, was studied. The study was carried out, firstly by taking into account the near-end and far-end faults in DOCRs coordination problem formulation; and then faults very close to the primary relays (nearend faults). The optimal coordination (OC) was achieved by simultaneously optimizing all variables (TDS and Ip) in nonlinear environment by using of Genetic algorithm nonlinear programming techniques. The results application of the above two approaches on 6-bus and 26-bus system verify that the far-end faults consideration on OC problem formulation don-t lose the optimality.
Abstract: This study investigated the pattern and seasonal index of influenza cases in Thailand. Our results showed that southern Thailand had the highest influenza incidence among the four regions of Thailand (i.e. north, northeast, central and southern Thailand). The influenza pattern in southern Thailand was similar to that of northeastern Thailand. Seasonal index values of influenza cases in Thailand were higher in the hot season than in the wet season. Influenza cases started to increase at the beginning of the hot season (April), reached a maximum in August, rapidly declined in the middle of the wet season and reached the lowest value in December. Seasonal index values for northern Thailand differed from other regions of Thailand.
Abstract: Apart from geometry, functionality is one of the most
significant hallmarks of a product. The functionality of a product can
be considered as the fundamental justification for a product
existence. Therefore a functional analysis including a complete and
reliable descriptor has a high potential to improve product
development process in various fields especially in knowledge-based
design. One of the important applications of the functional analysis
and indexing is in retrieval and design reuse concept. More than 75%
of design activity for a new product development contains reusing
earlier and existing design know-how. Thus, analysis and
categorization of product functions concluded by functional
indexing, influences directly in design optimization. This paper
elucidates and evaluates major classes for functional analysis by
discussing their major methods. Moreover it is finalized by
presenting a noble hybrid approach for functional analysis.
Abstract: Web intelligence, if made personal, can fuel the process of building communications around the interests and preferences of each individual customer or prospect, by providing specific behavioral insights about each individual. To become fully efficient, Web intelligence must reach a stage of a high-level maturity, passing throughout a process that involves five steps: (1) Web site analysis; (2) Web site and advertising optimization; (3) Segment targeting; (4) Interactive marketing (online only); and (5) Interactive marketing (online and offline). Discussing these steps in detail, the paper uncovers the real gold mine that is personal-level Web intelligence.
Abstract: Sulfide ion (S2-) is one of the most important ions to be
monitored due to its high toxicity, especially for aquatic organisms. In
this work, [Ca(2,2'-bipyridine)3]2+-intercalated montmorillonite was
prepared and used as a sensor to construct a potentiometric electrode to
measure sulfide ion in solution. The formation of [Ca(2,2'-
bipyridine)3]2+ in montmorillonite was confirmed by Fourier Transform
Infrared spectra. The electrode worked well at pH 4-12 and 4-10 in
sulfide solution 10-2 M and 10-3 M, respectively, in terms of Nernstian
slope. The sensor gave good precision and low cost.
Abstract: Among other factors that characterize satellite communication
channels is their high bit error rate. We present a system for
still image transmission over noisy satellite channels. The system
couples image compression together with error control codes to
improve the received image quality while maintaining its bandwidth
requirements. The proposed system is tested using a high resolution
satellite imagery simulated over the Rician fading channel. Evaluation
results show improvement in overall system including image quality
and bandwidth requirements compared to similar systems with different
coding schemes.
Abstract: The evolution of technology and construction techniques has enabled the upgrading of transport networks. In particular, the high-speed rail networks allow convoys to peak at above 300 km/h. These structures, however, often significantly impact the surrounding environment. Among the effects of greater importance are the ones provoked by the soundwave connected to train transit. The wave propagation affects the quality of life in areas surrounding the tracks, often for several hundred metres. There are substantial damages to properties (buildings and land), in terms of market depreciation. The present study, integrating expertise in acoustics, computering and evaluation fields, outlines a useful model to select project paths so as to minimize the noise impact and reduce the causes of possible litigation. It also facilitates the rational selection of initiatives to contain the environmental damage to the already existing railway tracks. The research is developed with reference to the Italian regulatory framework (usually more stringent than European and international standards) and refers to a case study concerning the high speed network in Italy.
Abstract: A Watson-Crick automaton is recently introduced as a
computational model of DNA computing framework. It works on
tapes consisting of double stranded sequences of symbols. Symbols
placed on the corresponding cells of the double-stranded sequences are
related by a complimentary relation. In this paper, we investigate a
variation of Watson-Crick automata in which both heads read the tape
in reverse directions. They are called reverse Watson-Crick finite
automata (RWKFA). We show that all of following four classes, i.e.,
simple, 1-limited, all-final, all-final and simple, are equal to
non-restricted version of RWKFA.
Abstract: In this paper, we use nonlinear system identification method to predict and detect process fault of a cement rotary kiln. After selecting proper inputs and output, an input-output model is identified for the plant. To identify the various operation points in the
kiln, Locally Linear Neuro-Fuzzy (LLNF) model is used. This model is trained by LOLIMOT algorithm which is an incremental treestructure
algorithm. Then, by using this method, we obtained 3
distinct models for the normal and faulty situations in the kiln. One of the models is for normal condition of the kiln with 15 minutes
prediction horizon. The other two models are for the two faulty situations in the kiln with 7 minutes prediction horizon are presented.
At the end, we detect these faults in validation data. The data collected from White Saveh Cement Company is used for in this study.
Abstract: Hydrogen that used as fuel in fuel cell vehicles can be
produced from renewable sources such as wind, solar, and hydro
technologies. PV-electrolyzer is one of the promising methods to
produce hydrogen with zero pollution emission. Hydrogen
production from a PV-electrolyzer system depends on the efficiency
of the electrolyzer and photovoltaic array, and sun irradiance at that
site. In this study, the amount of hydrogen is obtained using
mathematical equations for difference driving distance and sun peak
hours. The results show that the minimum of 99 PV modules are used
to generate 1.75 kgH2 per day for two vehicles.
Abstract: Today-s manufacturing companies are facing multiple and dynamic customer-supplier-relationships embedded in nonhierarchical production networks. This complex environment leads to problems with delivery reliability and wasteful turbulences throughout the entire network. This paper describes an operational model based on a theoretical framework which improves delivery reliability of each individual customer-supplier-relationship within non-hierarchical production networks of the European machinery and equipment industry. By developing a non-centralized coordination mechanism based on determining the value of delivery reliability and derivation of an incentive system for suppliers the number of in time deliveries can be increased and thus the turbulences in the production network smoothened. Comparable to an electronic stock exchange the coordination mechanism will transform the manual and nontransparent process of determining penalties for delivery delays into an automated and transparent market mechanism creating delivery reliability.
Abstract: In an interval graph G = (V,E) the distance between two vertices u, v is de£ned as the smallest number of edges in a path joining u and v. The eccentricity of a vertex v is the maximum among distances from all other vertices of V . The diameter (δ) and radius (ρ) of the graph G is respectively the maximum and minimum among all the eccentricities of G. The center of the graph G is the set C(G) of vertices with eccentricity ρ. In this context our aim is to establish the relation ρ = δ 2 for an interval graph and to determine the center of it.
Abstract: In this paper spatial variability of some chemical and
physical soil properties were investigated in mountain rangelands of
Nesho, Mazandaran province, Iran. 110 soil samples from 0-30 cm
depth were taken with systematic method on grid 30×30 m2 in
regions with different vegetation cover and transported to laboratory.
Then soil chemical and physical parameters including Acidity (pH),
Electrical conductivity, Caco3, Bulk density, Particle density, total
phosphorus, total Nitrogen, available potassium, Organic matter,
Saturation moisture, Soil texture (percentage of sand, silt and clay),
Sodium, Calcium, magnesium were measured in laboratory. Data
normalization was performed then was done statistical analysis for
description of soil properties and geostatistical analysis for indication
spatial correlation between these properties and were perpetrated
maps of spatial distribution of soil properties using Kriging method.
Results indicated that in the study area Saturation moisture and
percentage of Sand had highest and lowest spatial correlation
respectively.
Abstract: 2D/3D registration is a special case of medical image
registration which is of particular interest to surgeons. Applications
of 2D/3D registration are [1] radiotherapy planning and treatment
verification, spinal surgery, hip replacement, neurointerventions and
aortic stenting. The purpose of this paper is to provide a literature
review of the main methods for image registration for the 2D/3D
case. At the end of the paper an algorithm is proposed for 2D/3D
registration based on the Chebyssev polynomials iteration loop.
Abstract: Knowledge Discovery in Databases (KDD) is the process of extracting previously unknown, hidden and interesting patterns from a huge amount of data stored in databases. Data mining is a stage of the KDD process that aims at selecting and applying a particular data mining algorithm to extract an interesting and useful knowledge. It is highly expected that data mining methods will find interesting patterns according to some measures, from databases. It is of vital importance to define good measures of interestingness that would allow the system to discover only the useful patterns. Measures of interestingness are divided into objective and subjective measures. Objective measures are those that depend only on the structure of a pattern and which can be quantified by using statistical methods. While, subjective measures depend only on the subjectivity and understandability of the user who examine the patterns. These subjective measures are further divided into actionable, unexpected and novel. The key issues that faces data mining community is how to make actions on the basis of discovered knowledge. For a pattern to be actionable, the user subjectivity is captured by providing his/her background knowledge about domain. Here, we consider the actionability of the discovered knowledge as a measure of interestingness and raise important issues which need to be addressed to discover actionable knowledge.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. Transient mode super position method has been used to
find horizontal and vertical components of displacement and
dynamic stress. The finite element analysis software ANSYS has
been used on the proposed model to find the natural frequencies by
Block Lanczos technique and displacements and dynamic stresses by
transient mode super position method. A comparison of theoretical
(natural frequency and static stress) results with the finite element
analysis results has also been done. The effect of rotational speed of
the gears on the dynamic response of gear tooth has been studied and
design limits have been discussed.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: When consistently innovative business-models can
give companies a competitive advantage, longitudinal empirical
research, which can reflect dynamic business-model changes, has yet
to prove a definitive connection. This study consequently employs a
dynamic perspective in conjunction with innovation theory to examine
the relationship between the types of business-model innovation and
firm value. This study tries to examine various types of
business-model innovation in high-end and low-end technology
industries such as HTC and the 7-Eleven chain stores with research
periods of 14 years and 32 years, respectively. The empirical results
suggest that adopting radical business-model innovation in addition to
expanding new target markets can successfully lead to a competitive
advantage. Sustained advanced technological competences and
service/product innovation are the key successful factors in high-end
and low-end technology industry business-models respectively. In
sum up, the business-model innovation can yield a higher market value
and financial value in high-end technology industries than low-end
ones.
Abstract: Social media has led to paradigm shifts in ways
people work and do business, interact and socialize, learn and obtain
knowledge. So much so that social media has established itself as an
important spatial extension of this nation-s historicity and challenges.
Regardless of the enabling reputation and recommendation features
through social networks embedded in the social media system, the
overflow of broadcasted and publicized media contents turns the
table around from engendering trust to doubting the trust system.
When the trust is at doubt, the effects include deactivation of
accounts and creation of multiple profiles, which lead to the overflow
of 'ghost' contents (i.e. “the abundance of abandoned ships"). In
most literature, the study of trust can be related to culture; hence the
difference between Western-s “openness" and Eastern-s “blue-chip"
concepts in networking and relationships. From a survey on issues
and challenges among Malaysian social media users, 'authenticity'
emerges as one of the main factors that causes and is caused by other
factors. The other issue that has surfaced is credibility either in terms
of message/content and source. Another is the quality of the
knowledge that is shared. This paper explores the terrains of this
critical space which in recent years has been dominated increasingly
by, arguably, social networks embedded in the social media system,
the overflow of broadcasted and publicized media content.
Abstract: Most high-performance ac drives utilize a current
controller. The controller switches a voltage source inverter (VSI)
such that the motor current follows a set of reference current
waveforms. Fixed-band hysteresis (FBH) current control has been
widely used for the PWM inverter. We want to apply the same
controller for the PWM AC chopper. The aims of the controller is to
optimize the harmonic content at both input and output sides, while
maintaining acceptable losses in the ac chopper and to control in
wide range the fundamental output voltage. Fixed band controller has
been simulated and analyzed for a single-phase AC chopper and are
easily extended to three-phase systems. Simulation confirmed the
advantages and the excellent performance of the modulation method
applied for the AC chopper.