Abstract: Power cables are vulnerable to failure due to aging or
defects that occur with the passage of time under continuous
operation and loading stresses. PD detection and characterization
provide information on the location, nature, form and extent of the
degradation. As a result, PD monitoring has become an important
part of condition based maintenance (CBM) program among power
utilities. Online partial discharge (PD) localization of defect sources
in power cable system is possible using the time of flight method.
The information regarding the time difference between the main and
reflected pulses and cable length can help in locating the partial
discharge source along the cable length. However, if the length of
the cable is not known and the defect source is located at the extreme
ends of the cable or in the middle of the cable, then double ended
measurement is required to indicate the location of PD source. Use of
multiple sensors can also help in discriminating the cable PD or local/
external PD. This paper presents the experience and results from
online partial discharge measurements conducted in the laboratory
and the challenges in partial discharge source localization.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: In the recent years multimedia traffic and in particular
VoIP services are growing dramatically. We present a new algorithm
to control the resource utilization and to optimize the voice codec
selection during SIP call setup on behalf of the traffic condition
estimated on the network path.
The most suitable methodologies and the tools that perform realtime
evaluation of the available bandwidth on a network path have
been integrated with our proposed algorithm: this selects the best
codec for a VoIP call in function of the instantaneous available
bandwidth on the path. The algorithm does not require any explicit
feedback from the network, and this makes it easily deployable over
the Internet. We have also performed intensive tests on real network
scenarios with a software prototype, verifying the algorithm
efficiency with different network topologies and traffic patterns
between two SIP PBXs.
The promising results obtained during the experimental validation
of the algorithm are now the basis for the extension towards a larger
set of multimedia services and the integration of our methodology
with existing PBX appliances.
Abstract: Since the 80s huge efforts have been made to utilize
renewable energy sources to generate electric power. This paper
reports some aspects of integration of the distributed generators into
the low voltage distribution networks. An assessment of impact of the
distributed generators on the reliability indices of low voltage
network is performed. Results obtained from case study using low
voltage network, are presented and discussed.
Abstract: A diamond-like carbon (DLC) based solid-lubricant
film was designed and DLC films were successfully prepared using a
microwave plasma enhanced magnetron sputtering deposition
technology. Post-test characterizations including Raman
spectrometry, X-ray diffraction, nano-indentation test, adhesion test,
friction coefficient test were performed to study the influence of
substrate bias voltage on the mechanical properties of the W- and
S-doped DLC films. The results indicated that the W- and S-doped
DLC films also had the typical structure of DLC films and a better
mechanical performance achieved by the application of a substrate
bias of -200V.
Abstract: Optimization of filter banks based on the knowledge of input statistics has been of interest for a long time. Finite impulse response (FIR) Compaction filters are used in the design of optimal signal adapted orthonormal FIR filter banks. In this paper we discuss three different approaches for the design of interpolated finite impulse response (IFIR) compaction filters. In the first method, the magnitude squared response satisfies Nyquist constraint approximately. In the second and third methods Nyquist constraint is exactly satisfied. These methods yield FIR compaction filters whose response is comparable with that of the existing methods. At the same time, IFIR filters enjoy significant saving in the number of multipliers and can be implemented efficiently. Since eigenfilter approach is used here, the method is less complex. Design of IFIR filters in the least square sense is presented.
Abstract: An innovative tri-axes micro-power receiver is
proposed. The tri-axes micro-power receiver consists of two sets 3-D
micro-solenoids and one set planar micro-coils in which iron core is
embedded. The three sets of micro-coils are designed to be orthogonal
to each other. Therefore, no matter which direction the flux is present
along, the magnetic energy can be harvested and transformed into
electric power. Not only dead space of receiving power is mostly
reduced, but also transformation efficiency of electromagnetic energy
to electric power can be efficiently raised. By employing commercial
software, Ansoft Maxwell, the preliminary simulation results verify
that the proposed micro-power receiver can efficiently pick up the
energy transmitted by magnetic power source.
As to the fabrication process, the isotropic etching technique is
employed to micro-machine the inverse-trapezoid fillister so that the
copper wire can be successfully electroplated. The adhesion between
micro-coils and fillister is much enhanced.
Abstract: Visually impaired people find it extremely difficult to
acquire basic and vital information necessary for their living.
Therefore, they are at a very high risk of being socially excluded as a
result of poor access to information. In recent years, several attempts
have been made in improving the communication methods for
visually impaired people which involve tactile sensation such as
finger Braille, manual alphabets and the print on palm method and
several other electronic devices. But, there are some problems which
arise in such methods such as lack of privacy and lack of
compatibility to computer environment. This paper describes a low
cost Braille hand glove for blind people using slot sensors and
vibration motors with the help of which they can read and write emails,
text messages and read e-books. This glove allows the person
to type characters based on different Braille combination using six
slot sensors. The vibration in six different positions of the glove
which matches to the Braille code allows them to read characters.
Abstract: This paper aims to perform the second law analysis of
thermodynamics on the laminar film condensation of pure saturated
vapor flowing in the direction of gravity on an ellipsoid with variable
wall temperature. The analysis provides us understanding how the
geometric parameter- ellipticity and non-isothermal wall temperature
variation amplitude “A." affect entropy generation during film-wise
condensation heat transfer process. To understand of which
irreversibility involved in this condensation process, we derived an
expression for the entropy generation number in terms of ellipticity
and A. The result indicates that entropy generation increases with
ellipticity. Furthermore, the irreversibility due to finite temperature
difference heat transfer dominates over that due to condensate film
flow friction and the local entropy generation rate decreases with
increasing A in the upper half of ellipsoid. Meanwhile, the local
entropy generation rate enhances with A around the rear lower half of
ellipsoid.
Abstract: Introduction: Obesity is a major health risk issue in
the present day of life for one and all globally. Obesity is one of the
major concerns for public health according to recent increasing trends
in obesity-related diseases such as Type 2 diabetes. ( Kazuya,
1994).and hyperlipidemia, (Sakata,1990) .which are more prevalent
in Japanese adults with body mass index (BMI) values Z25 kg/m2.(
Japanese Ministry of Health and Welfare,1997). The purpose of the
study was to assess the effect of twelve weeks of brisk walking on
blood pressure and body mass index, anthropometric measurements
of obese males. Method: Thirty obese (BMI= above 30) males, aged
18 to 22 years, were selected from King Fahd University of
Petroleum & Minerals, Saudi Arabia. The subject-s height (cm) was
measured using a stadiometer and body mass (kg) was measured with
a electronic weighing machine. BMI was subsequently calculated
(kg/m2). The blood pressure was measured with standardized
sphygmomanometer in mm of Hg. All the measurements were taken
twice before and twice after the experimental period. The pre and
post anthropometric measurements of waist and hip circumference
were measured with the steel tape in cm. The subjects underwent
walking schedule two times in a week for 12 weeks. The 45 minute
sessions of brisk walking were undertaken at an average intensity of
65% to 85% of maximum HR (HRmax; calculated as 220-age).
Results & Discussion: Statistical findings revealed significant
changes from pre test to post test in case of both systolic blood
pressure and diastolic blood pressure in the walking group. Results
also showed significant decrease in their body mass index and
anthropometric measurements i.e. (waist & hip circumference).
Conclusion: It was concluded that twelve weeks brisk walking is
beneficial for lowering of blood pressure, body mass index, and
anthropometric circumference of obese males.
Abstract: Any rotation of a 3-dimensional object can be performed by three consecutive rotations over Euler angles. Intrinsic rotations produce the same result as extrinsic rotations in transformation. Euler rotations are the movement obtained by changing one of the Euler angles while leaving the other two constant. These Euler rotations are applied in a simple two-axis gimbals set mounted on an automotives. The values of Euler angles are [π/4, π/4, π/4] radians inside the angles ranges for a given coordinate system and these actual orientations can be directly measured from these gimbals set of moving automotives but it can occur the gimbals lock in application at [π/2.24, 0, 0] radians. In order to avoid gimbals lock, the values of quaternion must be [π/4.8, π/8.2, 0, π/4.8] radians. The four-gimbals set can eliminate gimbals lock.
Abstract: Physical urban form is recognized to be the media for
human transactions. It directly influences the travel demand of people
in a specific urban area and the amount of energy used for
transportation. Distorted, sprawling form often creates sustainability
problems in urban areas. It is declared in EU strategic planning
documents that compact urban form and mixed land use pattern must
be given the main focus to achieve better sustainability in urban
areas, but the methods to measure and compare these characteristics
are still not clear.
This paper presents the simple methods to measure the spatial
characteristics of urban form by analyzing the location and
distribution of objects in an urban environment. The extended CA
(cellular automata) model is used to simulate urban development
scenarios.
Abstract: Medical negligence disputes in Malaysia are mainly resolved through litigation by using the tort system. The tort system, being adversarial in nature has subjected parties to litigation hazards such as delay, excessive costs and uncertainty of outcome. The dissatisfaction of the tort system in compensating medically injured victims has created various alternatives to litigation. Amongst them is the implementation of a no-fault compensation system which would allow compensation to be given without the need of proving fault on the medical personnel. Instead, the community now bears the burden of compensating and at the end, promotes collective responsibility. For Malaysia, introducing a no-fault system would provide a tempting solution and may ultimately, achieve justice for the medical injured victims. Nevertheless, such drastic change requires a great deal of consideration to determine the suitability of the system and whether or not it will eventually cater for the needs of the Malaysian population
Abstract: This paper focuses on wormhole attacks detection in wireless sensor networks. The wormhole attack is particularly challenging to deal with since the adversary does not need to compromise any nodes and can use laptops or other wireless devices to send the packets on a low latency channel. This paper introduces an easy and effective method to detect and locate the wormholes: Since beacon nodes are assumed to know their coordinates, the straight line distance between each pair of them can be calculated and then compared with the corresponding hop distance, which in this paper equals hop counts × node-s transmission range R. Dramatic difference may emerge because of an existing wormhole. Our detection mechanism is based on this. The approximate location of the wormhole can also be derived in further steps based on this information. To the best of our knowledge, our method is much easier than other wormhole detecting schemes which also use beacon nodes, and to those have special requirements on each nodes (e.g., GPS receivers or tightly synchronized clocks or directional antennas), ours is more economical. Simulation results show that the algorithm is successful in detecting and locating wormholes when the density of beacon nodes reaches 0.008 per m2.
Abstract: Most of the image watermarking methods, using the properties of the human visual system (HVS), have been proposed in literature. The component of the visual threshold is usually related to either the spatial contrast sensitivity function (CSF) or the visual masking. Especially on the contrast masking, most methods have not mention to the effect near to the edge region. Since the HVS is sensitive what happens on the edge area. This paper proposes ultrasound image watermarking using the visual threshold corresponding to the HVS in which the coefficients in a DCT-block have been classified based on the texture, edge, and plain area. This classification method enables not only useful for imperceptibility when the watermark is insert into an image but also achievable a robustness of watermark detection. A comparison of the proposed method with other methods has been carried out which shown that the proposed method robusts to blockwise memoryless manipulations, and also robust against noise addition.
Abstract: This paper presents a system for discovering
association rules from collections of unstructured documents called
EART (Extract Association Rules from Text). The EART system
treats texts only not images or figures. EART discovers association
rules amongst keywords labeling the collection of textual documents.
The main characteristic of EART is that the system integrates XML
technology (to transform unstructured documents into structured
documents) with Information Retrieval scheme (TF-IDF) and Data
Mining technique for association rules extraction. EART depends on
word feature to extract association rules. It consists of four phases:
structure phase, index phase, text mining phase and visualization
phase. Our work depends on the analysis of the keywords in the
extracted association rules through the co-occurrence of the keywords
in one sentence in the original text and the existing of the keywords
in one sentence without co-occurrence. Experiments applied on a
collection of scientific documents selected from MEDLINE that are
related to the outbreak of H5N1 avian influenza virus.
Abstract: In first stage of each microwave receiver there is Low
Noise Amplifier (LNA) circuit, and this stage has important rule in
quality factor of the receiver. The design of a LNA in Radio
Frequency (RF) circuit requires the trade-off many importance
characteristics such as gain, Noise Figure (NF), stability, power
consumption and complexity. This situation Forces desingners to
make choices in the desing of RF circuits. In this paper the aim is to
design and simulate a single stage LNA circuit with high gain and
low noise using MESFET for frequency range of 5 GHz to 6 GHz.
The desing simulation process is down using Advance Design
System (ADS). A single stage LNA has successfully designed with
15.83 dB forward gain and 1.26 dB noise figure in frequency of 5.3
GHz. Also the designed LNA should be working stably In a
frequency range of 5 GHz to 6 GHz.
Abstract: This paper presents three models which enable the
customisation of Universal Description, Discovery and Integration
(UDDI) query results, based on some pre-defined and/or real-time
changing parameters. These proposed models detail the requirements,
design and techniques which make ranking of Web service discovery
results from a service registry possible. Our contribution is two fold:
First, we present an extension to the UDDI inquiry capabilities. This
enables a private UDDI registry owner to customise or rank the query
results, based on its business requirements. Second, our proposal
utilises existing technologies and standards which require minimal
changes to existing UDDI interfaces or its data structures. We believe
these models will serve as valuable reference for enhancing the
service discovery methods within a private UDDI registry
environment.
Abstract: In this paper a new control strategy based on Brain
Emotional Learning (BEL) model has been introduced. A modified
BEL model has been proposed to increase the degree of freedom,
controlling capability, reliability and robustness, which can be
implemented in real engineering systems.
The performance of the proposed BEL controller has been
illustrated by applying it on different nonlinear uncertain systems,
showing very good adaptability and robustness, while maintaining
stability.
Abstract: Mobile learning (m-learning) is a new method in teaching and learning process which combines technology of mobile device with learning materials. It can enhance student's engagement in learning activities and facilitate them to access the learning materials at anytime and anywhere. In Kolej Poly-Tech Mara (KPTM), this method is seen as an important effort in teaching practice and to improve student learning performance. The aim of this paper is to discuss the development of m-learning application called Mobile EEF Learning System (MEEFLS) to be implemented for Electric and Electronic Fundamentals course using Flash, XML (Extensible Markup Language) and J2ME (Java 2 micro edition). System Development Life Cycle (SDLC) was used as an application development approach. It has three modules in this application such as notes or course material, exercises and video. MEELFS development is seen as a tool or a pilot test for m-learning in KPTM.