Abstract: The calculation of buckling length factor (K) for steel
frames columns is a major and governing processes to determine the
dimensions steel frame columns cross sections during design. The
buckling length of steel frames columns has a direct effect on the cost
(weight) of using cross section. A new formula is required to
determine buckling length factor (K) by simplified way. In this
research a new formula for buckling length factor (K) was established
to determine by accurate method for a limited interval of columns
ends rigidity (GA, GB). The new formula can be used ease to
evaluate the buckling length factor without needing to complicated
equations or difficult charts.
Abstract: The plastic flow of metal in the extrusion process is
an important factor in controlling the mechanical properties of the
extruded products. It is, however, difficult to predict the metal flow
in three dimensional extrusions of sections due to the involvement of
re-entrant corners. The present study is to find an upper bound
solution for the extrusion of triangular sectioned through taper dies
from round sectioned billet. A discontinuous kinematically
admissible velocity field (KAVF) is proposed. From the proposed
KAVF, the upper bound solution on non-dimensional extrusion
pressure is determined with respect to the chosen process parameters.
The theoretical results are compared with experimental results to
check the validity of the proposed velocity field. An extrusion setup
is designed and fabricated for the said purpose, and all extrusions are
carried out using circular billets. Experiments are carried out with
commercially available lead at room temperature.
Abstract: Many Wireless Sensor Network (WSN) applications necessitate secure multicast services for the purpose of broadcasting delay sensitive data like video files and live telecast at fixed time-slot. This work provides a novel method to deal with end-to-end delay and drop rate of packets. Opportunistic Routing chooses a link based on the maximum probability of packet delivery ratio. Null Key Generation helps in authenticating packets to the receiver. Markov Decision Process based Adaptive Scheduling algorithm determines the time slot for packet transmission. Both theoretical analysis and simulation results show that the proposed protocol ensures better performance in terms of packet delivery ratio, average end-to-end delay and normalized routing overhead.
Abstract: Everyday the usages of the Internet increase and simply a world of the data become accessible. Network providers do not want to let the provided services to be used in harmful or terrorist affairs, so they used a variety of methods to protect the special regions from the harmful data. One of the most important methods is supposed to be the firewall. Firewall stops the transfer of such packets through several ways, but in some cases they do not use firewall because of its blind packet stopping, high process power needed and expensive prices. Here we have proposed a method to find a discriminate function to distinguish between usual packets and harmful ones by the statistical processing on the network router logs. So an administrator can alarm to the user. This method is very fast and can be used simply in adjacent with the Internet routers.
Abstract: Molar excess Volumes, VE ijk and speeds of sound , uijk of 2-pyrrolidinone (i) + benzene or toluene (j) + ethanol (k) ternary mixture have been measured as a function of composition at 308.15 K. The observed speeds of sound data have been utilized to determine excess isentropic compressiblities, ( E S κ )ijk of ternary (i + j + k) mixtures. Molar excess volumes, VE ijk and excess isentropic compressibilities, ( E S κ )ijk data have fitted to the Redlich-Kister equation to calculate ternary adjustable parameters and standard deviations. The Moelywn-Huggins concept (Huggins in Polymer 12: 389-399, 1971) of connectivity between the surfaces of the constituents of binary mixtures has been extended to ternary mixtures (using the concept of a connectivity parameter of third degree of molecules, 3ξ , which inturn depends on its topology) to obtain an expression that describes well the measured VE ijk and ( E S κ )ijk data.
Abstract: In this paper, the criteria of Ψ-eventual stability have been established for generalized impulsive differential systems of multiple dependent variables. The sufficient conditions have been obtained using piecewise continuous Lyapunov function. An example is given to support our theoretical result.
Abstract: In this study concept of experimental design is
successfully applied for the determination of optimum condition to
produce PP/SWCNT (Polypropylene/Single wall carbon nanotube)
nanocomposite. Central composite design as one of experimental
design techniques is employed for the optimization and statistical
determination of the significant factors influencing on the tensile
modulus and yield stress as mechanical properties of this
nanocomposite. The significant factors are SWCNT weight fraction
and acid treatment time for functionalizing the nanoparticles.
Optimum conditions are in 0.7 % of SWCNT weight fraction and 210
min as acid treatment time for 1112.75 ± 28 MPa as maximum tensile
modulus and in 216 min and 0.65 % as acid treatment time and
SWCNT weight fraction respectively for 40.26 ± 0.3 MPa as
maximum yield stress. Also after setting new experiments for test
these optimum conditions, found excelent agreement with predicted
values.
Abstract: In this paper, we propose a supervised method for
color image classification based on a multilevel sigmoidal neural
network (MSNN) model. In this method, images are classified into
five categories, i.e., “Car", “Building", “Mountain", “Farm" and
“Coast". This classification is performed without any segmentation
processes. To verify the learning capabilities of the proposed method,
we compare our MSNN model with the traditional Sigmoidal Neural
Network (SNN) model. Results of comparison have shown that the
MSNN model performs better than the traditional SNN model in the
context of training run time and classification rate. Both color
moments and multi-level wavelets decomposition technique are used
to extract features from images. The proposed method has been
tested on a variety of real and synthetic images.
Abstract: Tourists- eyes will often be attracted by the unique
phenomenon of the roadsides: betel nut beauties (pronounced as
binlang xishi in Mandarin), if they drive on the roads of Taiwan.
Sitting in the neon-lit glass stalls with attractive dress on the roadsides,
betel nut beauties usually sell betel nuts to the passing truckers or car
drivers with much of their efforts. Moreover, in order to attract
peoples- eyesight and increase the sales volume, the young girls are in
skimpy clothing to promote betel nuts or beverages to their customers.
Therefore, when the Chinese tourists come to Taiwan, to see the
unique betel nut beauty phenomenon has become one of their greatly
interested things or even a “must see". This paper describes betel but
beauties in Taiwan, explained why the Chinese tourists like to see
them in Taiwan and proposed propositions for examination.
Abstract: This paper reports on a receding horizon filtering for
mobile robot systems with cross-correlated sensor noises and
uncertainties. Also, the effect of uncertain parameters in the state of
the tracking error model performance is considered. A distributed
fusion receding horizon filter is proposed. The distributed fusion
filtering algorithm represents the optimal linear combination of the
local filters under the minimum mean square error criterion. The
derivation of the error cross-covariances between the local receding
horizon filters is the key of this paper. Simulation results of the
tracking mobile robot-s motion demonstrate high accuracy and
computational efficiency of the distributed fusion receding horizon
filter.
Abstract: This research adapts experimental design to investigate
the effect of conditioning or not and pre-exposure or not on brand
attitude, so it is a 2×2=4 factorial design. The results show that the
brand attitude of conditioning group is significantly higher than that of
unconditioning group. The brand attitude with pre-exposure is
significantly higher than that without pre-exposure. Conditioning or
not and pre-exposure or not have significant interaction. No matter the
celebrity is pre-exposure or not, the brand attitude is higher under
conditioning process.
Abstract: To evaluate genetic variation of wheat (Triticum aestivum) affected by heat and drought stress on eight Australian wheat genotypes that are parents of Doubled Haploid (HD) mapping populations at the vegetative stage, the water stress experiment was conducted at 65% field capacity in growth room. Heat stress experiment was conducted in the research field under irrigation over summer. Result show that water stress decreased dry shoot weight and RWC but increased osmolarity and means of Fv/Fm values in all varieties except for Krichauff. Krichauff and Kukri had the maximum RWC under drought stress. Trident variety was shown maximum WUE, osmolarity (610 mM/Kg), dry mater, quantum yield and Fv/Fm 0.815 under water stress condition. However, the recovery of quantum yield was apparent between 4 to 7 days after stress in all varieties. Nevertheless, increase in water stress after that lead to strong decrease in quantum yield. There was a genetic variation for leaf pigments content among varieties under heat stress. Heat stress decreased significantly the total chlorophyll content that measured by SPAD. Krichauff had maximum value of Anthocyanin content (2.978 A/g FW), chlorophyll a+b (2.001 mg/g FW) and chlorophyll a (1.502 mg/g FW). Maximum value of chlorophyll b (0.515 mg/g FW) and Carotenoids (0.234 mg/g FW) content belonged to Kukri. The quantum yield of all varieties decreased significantly, when the weather temperature increased from 28 ÔùªC to 36 ÔùªC during the 6 days. However, the recovery of quantum yield was apparent after 8th day in all varieties. The maximum decrease and recovery in quantum yield was observed in Krichauff. Drought and heat tolerant and moderately tolerant wheat genotypes were included Trident, Krichauff, Kukri and RAC875. Molineux, Berkut and Excalibur were clustered into most sensitive and moderately sensitive genotypes. Finally, the results show that there was a significantly genetic variation among the eight varieties that were studied under heat and water stress.
Abstract: Adaptive control involves modifying the control law
used by the controller to cope with the fact that the parameters of the
system being controlled change drastically due to change in
environmental conditions or in system itself. This technique is based
on the fundamental characteristic of adaptation of living organism.
The adaptive control process is one that continuously and
automatically measures the dynamic behavior of plant, compares it
with the desired output and uses the difference to vary adjustable
system parameters or to generate an actuating signal in such a way so
that optimal performance can be maintained regardless of system
changes. This paper deals with application of model reference
adaptive control scheme in first order system. The rule which is used
for this application is MIT rule. This paper also shows the effect of
adaptation gain on the system performance. Simulation is done in
MATLAB and results are discussed in detail.
Abstract: In this paper a new embedded Singly Diagonally
Implicit Runge-Kutta Nystrom fourth order in fifth order method for
solving special second order initial value problems is derived. A
standard set of test problems are tested upon and comparisons on the
numerical results are made when the same set of test problems are
reduced to first order systems and solved using the existing
embedded diagonally implicit Runge-Kutta method. The results
suggests the superiority of the new method.
Abstract: A manufacturing feature can be defined simply as a
geometric shape and its manufacturing information to create the shape.
In a feature-based process planning system, feature library that
consists of pre-defined manufacturing features and the manufacturing
information to create the shape of the features, plays an important role
in the extraction of manufacturing features with their proper
manufacturing information. However, to manage the manufacturing
information flexibly, it is important to build a feature library that can
be easily modified. In this paper, the implementation of Semantic Wiki
for the development of the feature library is proposed.
Abstract: En bloc assumes modeling all phases of the orthostatic test with the only one mathematical model, which allows the complex parametric view of orthostatic response. The work presents the implementation of a mathematical model for processing of the measurements of systolic, diastolic blood pressure and heart rate performed on volunteers during orthostatic test. The original assumption of model hypothesis that every postural change means only one Stressor, did not complying with the measurements of physiological circulation factor-time profiles. Results of the identification support the hypothesis that second postural change of orthostatic test causes induced Stressors, with the observation of a physiological regulation mechanism. Maximal demonstrations are on the heart rate and diastolic blood pressure-time profile, minimal are for the measurements of the systolic blood pressure. Presented study gives a new view on orthostatic test with impact on clinical practice.
Abstract: Stresses for the elastic-plastic transition and fully
plastic state have been derived for a thin rotating disc with inclusion
and results have been discussed numerically and depicted graphically.
It has been observed that the rotating disc with inclusion and made of
compressible material requires lesser angular speed to yield at the
internal surface whereas it requires higher percentage increase in
angular speed to become fully plastic as compare to disc made of
incompressible material.
Abstract: Many Thai movies have been very popular
domestically and internationally. Some movies were box office hits
and receiving awards. However, there has not yet been research
about how Thai movies can sell in international markets
The objectives of the research were 1) To analyze the
characteristics of Thai movies that can sell to world audiences; 2) To
investigate the factors making Thai movies into foreign markets. Thai
film professionals were interviewed. Their ideas were analyzed to
find out what factors contributing to Thai movies widely seen in
worldwide markets. Nine foreign audiences were also interviewed to
reveal what characteristics of Thai movies would be well accepted by
the markets.
The results showed that major characteristics of Thai movies
proving successful worldwide were cultural and exotic Thai movies,
outstanding genres, well-known actors, music and songs. Factors
contributing to global market were marketing, qualities of Thai
movies, and financial support from the government.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: The fault detection and diagnosis of complicated
production processes is one of essential tasks needed to run the process
safely with good final product quality. Unexpected events occurred in
the process may have a serious impact on the process. In this work,
triangular representation of process measurement data obtained in an
on-line basis is evaluated using simulation process. The effect of using
linear and nonlinear reduced spaces is also tested. Their diagnosis
performance was demonstrated using multivariate fault data. It has
shown that the nonlinear technique based diagnosis method produced
more reliable results and outperforms linear method. The use of
appropriate reduced space yielded better diagnosis performance. The
presented diagnosis framework is different from existing ones in that it
attempts to extract the fault pattern in the reduced space, not in the
original process variable space. The use of reduced model space helps
to mitigate the sensitivity of the fault pattern to noise.