Abstract: Air infiltration in mass scale industrial applications of
bio char production is inevitable. The presence of oxygen during the
carbonization process is detrimental to the production of biochar yield
and properties. The experiment was carried out on several wood
species in a fixed-bed pyrolyser under various fractions of oxygen
ranging from 0% to 11% by varying nitrogen and oxygen composition
in the pyrolysing gas mixtures at desired compositions. The bed
temperature and holding time were also varied. Process optimization
was carried out by Response Surface Methodology (RSM) by
employing Central Composite Design (CCD) using Design Expert 6.0
Software. The effect of oxygen ratio and holding time on biochar yield
within the range studied were statistically significant. From the
analysis result, optimum condition of 15.2% biochar yield of
mangrove wood was predicted at pyrolysis temperature of 403 oC,
oxygen percentage of 2.3% and holding time of two hours. This
prediction agreed well with the experiment finding of 15.1% biochar
yield.
Abstract: This study reports the preparation of soft magnetic
ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213
mm and, with a thickness of approximately 22 μm ± 2 μm. The microstructure and magnetic properties of the ribbons were
characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material
properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic
measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide
ribbon, the magnetic responses are not uniformly distributed. To
understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a
ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: Hair is a non homogenous complex material which
can be associated with a polymer. It is made up 95% of Keratin.
Hair has a great social significance for human beings. In the High
Middle Ages, for example, long hairs have been reserved for kings
and nobles.
Most common interest in hair is focused on hair growth, hair types
and hair care, but hair is also an important biomaterial which can
vary depending on ethnic origin or on age, hair colour for example
can be a sign of ethnic ancestry or age (dark hair for Asiatic, blond
hair for Caucasian and white hair for old people in general).
In this context, different approaches have been conducted to
determine the differences in mechanical properties and characterize
the fracture topography at the surface of hair depending on its type
and its age.
A tensile testing machine was especially designed to achieve
tensile tests on hair. This device is composed of a microdisplacement
system and a force sensor whose peak load is limited to
3N. The curves and the values extracted from each experiment, allow
us to compare the evolution of the mechanical properties from one
hair to another.
Observations with a Scanning Electron Microscope (SEM) and
with an interferometer were made on different hairs. Thus, it is
possible to access the cuticle state and the fracture topography for
each category.
Abstract: A method is presented for obtaining the error probability for block codes. The method is based on the eigenvalueeigenvector properties of the code correlation matrix. It is found that under a unary transformation and for an additive white Gaussian noise environment, the performance evaluation of a block code becomes a one-dimensional problem in which only one eigenvalue and its corresponding eigenvector are needed in the computation. The obtained error rate results show remarkable agreement between simulations and analysis.
Abstract: In this paper, the construction of a detailed spine
model is presented using the LifeMOD Biomechanics Modeler. The
detailed spine model is obtained by refining spine segments in
cervical, thoracic and lumbar regions into individual vertebra
segments, using bushing elements representing the intervertebral
discs, and building various ligamentous soft tissues between
vertebrae. In the sagittal plane of the spine, constant force will be
applied from the posterior to anterior during simulation to determine
dynamic characteristics of the spine. The force magnitude is
gradually increased in subsequent simulations. Based on these
recorded dynamic properties, graphs of displacement-force
relationships will be established in terms of polynomial functions by
using the least-squares method and imported into a haptic integrated
graphic environment. A thoracolumbar spine model with complex
geometry of vertebrae, which is digitized from a resin spine
prototype, will be utilized in this environment. By using the haptic
technique, surgeons can touch as well as apply forces to the spine
model through haptic devices to observe the locomotion of the spine
which is computed from the displacement-force relationship graphs.
This current study provides a preliminary picture of our ongoing
work towards building and simulating bio-fidelity scoliotic spine
models in a haptic integrated graphic environment whose dynamic
properties are obtained from LifeMOD. These models can be helpful
for surgeons to examine kinematic behaviors of scoliotic spines and
to propose possible surgical plans before spine correction operations.
Abstract: This paper presents the design, fabrication and
evaluation of magneto-rheological damper. Semi-active control
devices have received significant attention in recent years because
they offer the adaptability of active control devices without requiring
the associated large power sources. Magneto-Rheological (MR)
dampers are semi- active control devices that use MR fluids to
produce controllable dampers. They potentially offer highly reliable
operation and can be viewed as fail-safe in that they become passive
dampers if the control hardware malfunction. The advantage of MR
dampers over conventional dampers are that they are simple in
construction, compromise between high frequency isolation and
natural frequency isolation, they offer semi-active control, use very
little power, have very quick response, has few moving parts, have a
relax tolerances and direct interfacing with electronics. Magneto-
Rheological (MR) fluids are Controllable fluids belonging to the
class of active materials that have the unique ability to change
dynamic yield stress when acted upon by an electric or magnetic
field, while maintaining viscosity relatively constant. This property
can be utilized in MR damper where the damping force is changed by
changing the rheological properties of the fluid magnetically. MR
fluids have a dynamic yield stress over Electro-Rheological fluids
(ER) and a broader operational temperature range. The objective of
this papert was to study the application of an MR damper to vibration
control, design the vibration damper using MR fluids, test and
evaluate its performance. In this paper the Rheology and the theory
behind MR fluids and their use on vibration control were studied.
Then a MR vibration damper suitable for vehicle suspension was
designed and fabricated using the MR fluid. The MR damper was
tested using a dynamic test rig and the results were obtained in the
form of force vs velocity and the force vs displacement plots. The
results were encouraging and greatly inspire further research on the
topic.
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.
Abstract: The purpose of this paper is to present the fuzzy contraction
properties of the Hutchinson-Barnsley operator on the fuzzy
hyperspace with respect to the Hausdorff fuzzy metrics. Also we
discuss about the relationships between the Hausdorff fuzzy metrics
on the fuzzy hyperspaces. Our theorems generalize and extend some
recent results related with Hutchinson-Barnsley operator in the metric
spaces.
Abstract: Soft clays are defined as cohesive soil whose water
content is higher than its liquid limits. Thus, soil-cement mixing is
adopted to improve the ground conditions by enhancing the strength
and deformation characteristics of the soft clays. For the above
mentioned reasons, a series of laboratory tests were carried out to
study some fundamental mechanical properties of cement stabilized
soft clay. The test specimens were prepared by varying the portion of
ordinary Portland cement to the soft clay sample retrieved from the
test site of RECESS (Research Centre for Soft Soil). Comparisons
were made for both homogeneous and columnar system specimens
by relating the effects of cement stabilized clay of for 0, 5 and 10 %
cement and curing for 3, 28 and 56 days. The mechanical properties
examined included one-dimensional compressibility and undrained
shear strength. For the mechanical properties, both homogeneous and
columnar system specimens were prepared to examine the effect of
different cement contents and curing periods on the stabilized soil.
The one-dimensional compressibility test was conducted using an
oedometer, while a direct shear box was used for measuring the
undrained shear strength. The higher the value of cement content, the
greater is the enhancement of the yield stress and the decrease of
compression index. The value of cement content in a specimen is a
more active parameter than the curing period.
Abstract: The main goal of the study is to analyze all relevant properties of the electro hydraulic systems and based on that to make a proper choice of the neural network control strategy that may be used for the control of the mechatronic system. A combination of electronic and hydraulic systems is widely used since it combines the advantages of both. Hydraulic systems are widely spread because of their properties as accuracy, flexibility, high horsepower-to-weight ratio, fast starting, stopping and reversal with smoothness and precision, and simplicity of operations. On the other hand, the modern control of hydraulic systems is based on control of the circuit fed to the inductive solenoid that controls the position of the hydraulic valve. Since this circuit may be easily handled by PWM (Pulse Width Modulation) signal with a proper frequency, the combination of electrical and hydraulic systems became very fruitful and usable in specific areas as airplane and military industry. The study shows and discusses the experimental results obtained by the control strategy of neural network control using MATLAB and SIMULINK [1]. Finally, the special attention was paid to the possibility of neuro-controller design and its application to control of electro-hydraulic systems and to make comparative with other kinds of control.
Abstract: The first and basic cause of the failure of concrete is repeated freezing (thawing) of moisture contained in the pores, microcracks, and cavities of the concrete. On transition to ice, water existing in the free state in cracks increases in volume, expanding the recess in which freezing occurs. A reduction in strength below the initial value is to be expected and further cycle of freezing and thawing have a further marked effect. By using some experimental parameters like nuclear magnetic resonance variation (NMR), enthalpy-temperature (or heat capacity) variation, we can resolve between the various water states and their effect on concrete properties during cooling through the freezing transition temperature range. The main objective of this paper is to describe the principal type of water responsible for the reduction in strength and structural damage (frost damage) of concrete following repeated freeze –thaw cycles. Some experimental work was carried out at the institute of cryogenics to determine what happens to water in concrete during the freezing transition.
Abstract: This paper presents a part of research on the
rheological properties of bitumen modified by thermoplastic namely
linear low density polyethylene (LLDPE), high density polyethylene
(HDPE) and polypropylene (PP) and its interaction with 80 pen base
bitumen. As it is known that the modification of bitumen by the use
of polymers enhances its performance characteristics but at the same
time significantly alters its rheological properties. The rheological
study of polymer modified bitumen (PMB) was made through
penetration, ring & ball softening point and viscosity test. The results
were then related to the changes in the rheological properties of
polymer modified bitumen. It was observed that thermoplastic
copolymer shows profound effect on penetration rather than
softening point. The viscoelastic behavior of polymer modified
bitumen depend on the concentration of polymer, mixing
temperature, mixing technique, solvating power of base bitumen and
molecular structure of polymer used. PP offer better blend in
comparison to HDPE and LLDPE. The viscosity of base bitumen was
also enhanced with the addition of polymer. The pseudoplastic
behavior was more prominent for HDPE and LLDPE than PP. Best
results were obtained when polymer concentration was kept below
3%
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: During recent years, the traditional learning
approaches have undergone fundamental changes due to the
emergence of new technologies such as multimedia, hypermedia and
telecommunication. E-learning is a modern world phenomenon that
has come into existence in the information age and in a knowledgebased
society. E-learning has developed significantly within a short
period of time. Thus it is of a great significant to secure information,
allow a confident access and prevent unauthorized accesses. Making
use of individuals- physiologic or behavioral (biometric) properties is
a confident method to make the information secure. Among the
biometrics, fingerprint is more acceptable and most countries use it as
an efficient methods of identification. This article provides a new
method to compare the fingerprint comparison by pattern recognition
and image processing techniques. To verify fingerprint, the shortest
distance method is used together with perceptronic multilayer neural
network functioning based on minutiae. This method is highly
accurate in the extraction of minutiae and it accelerates comparisons
due to elimination of false minutiae and is more reliable compared
with methods that merely use directional images.
Abstract: Concerning the measurement of friction properties of
textiles and fabrics using Kawabata Evaluation System (KES), whose
output is constrained to the surface friction factor of fabric, and no
other data would be generated; this research has been conducted to
gain information about surface roughness regarding its surface
friction factor. To assess roughness properties of light nonwovens, a
3-dimensional model of a surface has been simulated with regular
sinuous waves through it as an ideal surface. A new factor was
defined, namely Surface Roughness Factor, through comparing
roughness properties of simulated surface and real specimens. The
relation between the proposed factor and friction factor of specimens
has been analyzed by regression, and results showed a meaningful
correlation between them. It can be inferred that the new presented
factor can be used as an acceptable criterion for evaluating the
roughness properties of light nonwoven fabrics.
Abstract: Cement, the most widely used construction material
is very brittle and characterized by low tensile strength and strain
capacity. Macro to nano fibers are added to cement to provide
tensile strength and ductility to it. Carbon Nanotube (CNT), one of
the nanofibers, has proven to be a promising reinforcing material in
the cement composites because of its outstanding mechanical
properties and its ability to close cracks at the nano level. The
experimental investigations for CNT reinforced cement is costly,
time consuming and involves huge number of trials. Mathematical
modeling of CNT reinforced cement can be done effectively and
efficiently to arrive at the mechanical properties and to reduce the
number of trials in the experiments. Hence, an attempt is made to
numerically study the effective mechanical properties of CNT
reinforced cement numerically using Representative Volume
Element (RVE) method. The enhancement in its mechanical
properties for different percentage of CNTs is studied in detail.
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The analysis is carried out using Hamilton's principle. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of clamped-free boundary conditions
Abstract: Bond graph models of an electrical transformer
including the nonlinear saturation are presented. These models
determine the relation between self and mutual inductances, and
the leakage and magnetizing inductances of power transformers
with two and three windings using the properties of a bond
graph. The modelling and analysis using this methodology to
three phase power transformers or transformers with internal
incipient faults can be extended.
Abstract: This paper gives an overview of the mapping
mechanism of SEAM-a methodology for the automatic generation of
knowledge models and its mapping onto Java codes. It discusses the
rules that will be used to map the different components in the
knowledge model automatically onto Java classes, properties and
methods. The aim of developing this mechanism is to help in the
creation of a prototype which will be used to validate the knowledge
model which has been generated automatically. It will also help to
link the modeling phase with the implementation phase as existing
knowledge engineering methodologies do not provide for proper
guidelines for the transition from the knowledge modeling phase to
development phase. This will decrease the development overheads
associated to the development of Knowledge Based Systems.
Abstract: This research was to evaluate a technical feasibility of
making single-layer experimental particleboard panels from bamboo
waste (Dendrocalamus asper Backer) by converting bamboo into
strips, which are used to make laminated bamboo furniture. Variable
factors were density (600, 700 and 800 kg/m3) and temperature of
condition (25, 40 and 55 °C). The experimental panels were tested for
their physical and mechanical properties including modulus of
elasticity (MOE), modulus of rupture (MOR), internal bonding
strength (IB), screw holding strength (SH) and thickness swelling
values according to the procedures defined by Japanese Industrial
Standard (JIS). The test result of mechanical properties showed that
the MOR, MOE and IB values were not in the set criteria, except the
MOR values at the density of 700 kg/m3 at 25 °C and at the density
of 800 kg/m3 at 25 and 40 °C, the IB values at the density of 600
kg/m3, at 40 °C, and at the density of 800 kg/m3 at 55 °C. The SH
values had the test result according to the set standard, except with
the density of 600 kg/m3, at 40 and 55 °C. Conclusively, a valuable
renewable biomass, bamboo waste could be used to manufacture
boards.