Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: The world wide web network is a network with a
complex topology, the main properties of which are the distribution
of degrees in power law, A low clustering coefficient and a weak
average distance. Modeling the web as a graph allows locating the
information in little time and consequently offering a help in the
construction of the research engine. Here, we present a model based
on the already existing probabilistic graphs with all the aforesaid
characteristics. This work will consist in studying the web in order to
know its structuring thus it will enable us to modelize it more easily
and propose a possible algorithm for its exploration.
Abstract: Different services based on different switching
techniques in wireless networks leads to drastic changes in the
properties of network traffic. Because of these diversities in services,
network traffic is expected to undergo qualitative and quantitative
variations. Hence, assumption of traffic characteristics and the
prediction of network events become more complex for the wireless
networks. In this paper, the traffic characteristics have been studied
by collecting traces from the mobile switching centre (MSC). The
traces include initiation and termination time, originating node, home
station id, foreign station id. Traffic parameters namely, call interarrival
and holding times were estimated statistically. The results
show that call inter-arrival and distribution time in this wireless
network is heavy-tailed and follow gamma distributions. They are
asymptotically long-range dependent. It is also found that the call
holding times are best fitted with lognormal distribution. Based on
these observations, an analytical model for performance estimation is
also proposed.
Abstract: Renewable energy is derived from natural processes
that are replenished constantly. Included in the definition is
electricity and heat generated from solar, wind, ocean, hydropower,
biomass, geothermal resources, and bio-fuels and hydrogen derived
from renewable resources. Each of these sources has unique
characteristics which influence how and where they are used. This
paper presents the modeling the simulation of solar and hydro hybrid
energy sources in MATLAB/SIMULINK environment. It simulates
all quantities of Hybrid Electrical Power system (HEPS) such as AC
output current of the inverter that injected to the load/grid, load
current, grid current. It also simulates power output from PV and
Hydraulic Turbine Generator (HTG), power delivered to or from grid
and finally power factor of the inverter for PV, HTG and grid. The
proposed circuit uses instantaneous p-q (real-imaginary) power
theory.
Abstract: Since the emergence of e-Commerce, the world of
business has witnessed a radical shift in the way business activities
are conducted. However, the emergence of m-Commerce has further
pushed the boundaries of virtual commerce revolution. As a result,
there seems to be a growing blur in the distinction between e-
Commerce and m-Commerce. In addition, existing definitions for
both forms of commerce highlight characteristics (e.g. type of device
and activity conducted) that may be applicable to both concepts. The
aim of this paper is to identify the characteristics that help define and
delineate between e- and m- Commerce. The paper concludes that
characteristics of mobility, ubiquity and immediacy provide a clearer
and simpler template to distinguish between e-Commerce and m-
Commerce.
Abstract: In the present study, we have synthesized Cr and Fe
doped zinc oxide (ZnO) nanostructures (Zn1-δCraFebO; where δ = a +
b = 20%, a = 5, 6, 8 & 10% and b = 15, 14, 12 & 10%) via sol-gel
method at different doping concentrations. The synthesized samples
were characterized for structural properties by X-ray diffractrometer
and field emission scanning electron microscope and the optical
properties were carried out through photoluminescence and UVvisible
spectroscopy. The particle size calculated through field
emission scanning electron microscope varies from 41 to 96 nm for
the samples synthesized at different doping concentrations. The
optical band gaps calculated through UV-visible spectroscopy are
found to be decreasing from 3.27 to 3.02 eV as the doping
concentration of Cr increases and Fe decreases.
Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: Fritillaria oranensis (Liliaceae) was described in 1874
by pomel from Algeria. Plant samples have been collected from the
mount of Tessala (Sidi-Bel-Abbes). The morphological features of
various organs of the plant are described in detail. In the
morphological part of the study, features of various organs of the
plants such as stem and leaf were determined and illustrated.
Ecological studies provide information about the physical and
chemical structure of soil types in Tessala Mountain. The aim of this
original investigation is to put forth ecological and anatomical
features of these species for the first time, but at the same time given
detailed account of the morphological characteristics of the stem and
leaf of Fritillaria oranensis.
Abstract: The phased-array ultrasound transducer types are
utilities for medical ultrasonography as well as optical imaging.
However, their discontinuity characteristic limits the applications due
to the artifacts contaminated into the reconstructed images. Because
of the effects of the ultrasound pressure field pattern to the echo
ultrasonic waves as well as the optical modulated signal, the side
lobes of the focused ultrasound beam induced by discontinuity of the
phased-array ultrasound transducer might the reason of the artifacts.
In this paper, a simple method in approach of numerical simulation
was used to investigate the limitation of discontinuity of the elements
in phased-array ultrasound transducer and their effects to the
ultrasound pressure field. Take into account the change of ultrasound
pressure field patterns in the conditions of variation of the pitches
between elements of the phased-array ultrasound transducer, the
appropriated parameters for phased-array ultrasound transducer
design were asserted quantitatively.
Abstract: In the present work, hydrogen gas sensor of modest
sensitivity utilizing functionalized multiwalled carbon nanotubes
partially decorated with tin oxide nanoparticles (F-MWCNTs/SnO2)
has been fabricated. This sensing material was characterized by
scanning electron microscopy (SEM). In addition, a remarkable
finding was that the F-MWCNTs/SnO2 sensor shows good sensitivity
as compared to F-MWCNTs for low concentration (0.05-1% by
volume) of H2 gas. The fabricated sensors show complete resistance
recovery and good repeatability when exposed to H2 gas at the room
temperature conditions.
Abstract: In this paper two approaches to joint signal detection,
time of arrival (ToA) and angle of arrival (AoA) estimation in
multi-element antenna array are investigated. Two scenarios were
considered: first one, when the waveform of the useful signal
is known a priori and, second one, when the waveform of the
desired signal is unknown. For first scenario, the antenna array
signal processing based on multi-element matched filtering (MF)
with the following non-coherent detection scheme and maximum
likelihood (ML) parameter estimation blocks is exploited. For second
scenario, the signal processing based on the antenna array elements
covariance matrix estimation with the following eigenvector analysis
and ML parameter estimation blocks is applied. The performance
characteristics of both signal processing schemes are thoroughly
investigated and compared for different useful signals and noise
parameters.
Abstract: Metallic foams have good potential for lightweight
structures for impact and blast mitigation. Therefore it is important to
find out the optimized foam structure (i.e. cell size, shape, relative
density, and distribution) to maximise energy absorption. In this
paper, quasistatic compression and microstructural characterization
of closed-cell aluminium foams of different pore size and cell
distributions have been carried out. We present results for two
different aluminium metal foams of density 0.49-0.51 g/cc and 0.31-
0.34 g/cc respectively that have been tested in quasi-static
compression. The influence of cell geometry and cell topology on
quasistatic compression behaviour has been investigated using optical
microscope and computed tomography (micro-CT) analysis. It is
shown that the deformation is not uniform in the structure and
collapse begins at the weakest point.
Abstract: In this paper, the effect of WC-12Co particle
temperature in HVOF thermal spraying process on the coating
thickness has been studied. The statistical results show that the spray
distance and oxygen-to-fuel ratio are effective factors on particle
characterization and thickness of HVOF thermal spraying coatings.
Spray Watch diagnostic system, scanning electron microscopy
(SEM), X-ray diffraction and thickness measuring system were used
for this purpose.
Abstract: Human movement in the real world provides
important information for developing human behaviour models and
simulations. However, it is difficult to assess ‘real’ human behaviour
since there is no established method available. As part of the AUNTSUE
(Accessibility and User Needs in Transport – Sustainable Urban
Environments) project, this research aimed to propose a method to
assess human movement and behaviour in crowded areas. The
method is based on the three major steps of video recording,
conceptual behavior modelling and video analysis. The focus is on
individual human movement and behaviour in normal situations
(panic situations are not considered) and the interactions between
individuals in localized areas. Emphasis is placed on gaining
knowledge of characteristics of human movement and behaviour in
the real world that can be modelled in the virtual environment.
Abstract: A novel simulation method to determine the
displacements of machine tools due to thermal factors is presented.
The specific characteristic of this method is the employment of
original CAD data from the design process chain, which is
interpreted by an algorithm in terms of geometry-based allocation of
convection and radiation parameters. Furthermore analogous models
relating to the thermal behaviour of machine elements are
automatically implemented, which were gained by extensive
experimental testing with thermography imaging. With this a
transient simulation of the thermal field and in series of the
displacement of the machine tool is possible simultaneously during
the design phase. This method was implemented and is already used
industrially in the design of machining centres in order to improve
the quality of herewith manufactured workpieces.
Abstract: Mech-Degla, Degla-Beida and Frezza are the date
(Phoenix dactylifera L.) common varieties with a more or less good
availability and feeble trade value. Some morphologic and
physicochemical factors were determined. Results show that the
whole date weight is significantly different (P= 95%) concerning
Mech-Degla and Degla-Beida which are more commercialized than
Frezza whereas the pulp mass proportion in relation to whole fruits is
highest for Frezza (88.28%). Moreover, there is a large variability
concerning the weights and densities of constitutive tissues in each
variety. The white tissue is dominant in Mech-Degla in opposite to
the two other varieties. The variance analyze showed that the
difference in weights between brown and white tissues is significant
(P = 95%) for all studied varieties. Some other morphologic and
chemical proprieties of the whole pulps and their two constitutive
parts (brown or pigmented and white) are also investigated. The
predominance of phenolics in Mech-Degla (4.01g/100g, w.b) and
Frezza (4.96 g/100g, w.b) pulps brown part is the main result
revealed in this study.
Abstract: This research aims to investigate callus induction,
somatic embryogenesis and indirect plant regeneration of Crassula
ovata (Mill.) Druce – the famous ornamental plant. Experiment no.1:
Callus induction was obtained from leaf and stem explants on
Murashige and Skoog (MS) medium supplemented with various plant
growth regulators (PGRs). Effects of different PGRs, plant
regeneration and subsequent plantlet conversion were also assessed.
Indirect plant regeneration was achieved from the callus of stem
explants by the addition of 1.5 mg/L Kinetin (KN) alone. Best shoot
induction was achieved (6.5 shoots/per explant) after 60 days. For
successful rooting, regenerated plantlets were sub-cultured on the
same MS media supplemented with 1.5 mg/L KN alone. The rooted
plantlets were acclimatized and the survival rate was 90%.
Experiment no.2: Results revealed that 0.5 mg/L 2,4-D alone and in
combination with 1.0 mg/L 6-Benzyladenine (BA) gave 89.8% callus
from the stem explants as compared to leaf explants. Callus
proliferation and somatic embryo formation were also evaluated by
‘Double Staining Method’ and different stages of somatic
embryogenesis were revealed by scanning electron microscope. Full
Strength MS medium produced the highest number (49.6%) of
cotyledonary stage somatic embryos (SEs). Mature cotyledonary
stage SEs developed into plantlets after 12 weeks of culture. Wellrooted
plantlets were successfully acclimatized at the survival rate of
85%. Indirectly regenerated plants did not show any detectable
variation in morphological and growth characteristics when
compared with the donor plant.
Abstract: This paper presents a method for the efficient
implementation of a unidirectional or bidirectional DC/DC converter.
The DC/DC converter is used essentially for energy exchange
between the low voltage service battery and a high voltage battery
commonly found in Electric Vehicle applications. In these
applications, apart from cost, efficiency of design is an important
characteristic. A useful way to reduce the size of electronic
equipment in the electric vehicles is proposed in this paper. The
technique simplifies the mechanical complexity and maximizes the
energy usage using the latest converter control techniques. Moreover
a bidirectional battery charger for hybrid electric vehicles is also
implemented in this paper. Several simulations on the test system
have been carried out in Matlab/Simulink environment. The results
exemplify the robustness of the proposed design methodology in case
of a 1.5 KW DC-DC converter.
Abstract: This paper considers the characterization of a complex
electromagnetic environment due to multiple sources of
electromagnetic radiation as a five-dimensional surface which can be
described by a set of several surface sections including: instant EM
field intensity distribution maps at a given frequency and altitude,
instantaneous spectrum at a given location in space and the time
evolution of the electromagnetic field spectrum at a given point in
space. This characterization if done over time can enable the
exposure levels of Radio Frequency Radiation at every point in the
analysis area to be determined and results interpreted based on
comparison of the determined RFR exposure level with the safe
guidelines for general public exposure given by recognized body
such as the International commission on non-ionizing radiation
protection (ICNIRP), Institute of Electrical and Electronic Engineers
(IEEE), the National Radiation Protection Authority (NRPA).