Abstract: Ambient hydrolysis products in moist air and
hydrolysis kinetics in argon with humidity of RH1.5% for
polycrystalline LiH powders and sintered bulks were investigated by
X-ray diffraction, Raman spectroscopy and gravimetry. The results
showed that the hydrolysis products made up a layered structure of
LiOH•H2O/LiOH/Li2O from surface of the sample to inside. In low
humid argon atmosphere, the primary hydrolysis product was Li2O
rather than LiOH. The hydrolysis kinetic curves of LiH bulks present a
paralinear shape, which could be explained by the “Layer Diffusion
Control" model. While a three-stage hydrolysis kinetic profile was
observed for LiH powders under the same experimental conditions.
The first two sections were similar to that of the bulk samples, and the
third section also presents a linear reaction kinetics but with a smaller
reaction rate compared to the second section because of a larger
exothermic effect for the hydrolysis reaction of LiH powder.
Abstract: The detection of outliers is very essential because of
their responsibility for producing huge interpretative problem in
linear as well as in nonlinear regression analysis. Much work has
been accomplished on the identification of outlier in linear
regression, but not in nonlinear regression. In this article we propose
several outlier detection techniques for nonlinear regression. The
main idea is to use the linear approximation of a nonlinear model and
consider the gradient as the design matrix. Subsequently, the
detection techniques are formulated. Six detection measures are
developed that combined with three estimation techniques such as the
Least-Squares, M and MM-estimators. The study shows that among
the six measures, only the studentized residual and Cook Distance
which combined with the MM estimator, consistently capable of
identifying the correct outliers.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: Non-uniform current distribution in polymer
electrolyte membrane fuel cells results in local over-heating,
accelerated ageing, and lower power output than expected. This
issue is very critical when fuel cell experiences water flooding. In
this work, the performance of a PEM fuel cell is investigated under
cathode flooding conditions. Two-dimensional partially flooded
GDL models based on the conservation laws and electrochemical
relations are proposed to study local current density distributions
along flow fields over a wide range of cell operating conditions.
The model results show a direct association between cathode inlet
humidity increases and that of average current density but the
system becomes more sensitive to flooding. The anode inlet
relative humidity shows a similar effect. Operating the cell at
higher temperatures would lead to higher average current densities
and the chance of system being flooded is reduced. In addition,
higher cathode stoichiometries prevent system flooding but the
average current density remains almost constant. The higher anode
stoichiometry leads to higher average current density and higher
sensitivity to cathode flooding.
Abstract: According to the Auckland climate, building passive
design more focus on improving winter indoor thermal and health
conditions. Based on field study data of indoor air temperature and
relative humidity close to ceiling and floor of an insulated Auckland
townhouse with and without a whole home mechanical ventilation
system, this study is to analysis variation of indoor microclimate data
of an Auckland townhouse using or not using the mechanical
ventilation system to evaluate winter indoor thermal and health
conditions for the future house design with a mechanical ventilation
system.
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: The removal of hydrogen sulphide is required for reasons of health, odour problems, safety and corrosivity problems. The means of removing hydrogen sulphide mainly depend on its concentration and kind of medium to be purified. The paper deals with a method of hydrogen sulphide removal from the air by its catalytic oxidation to elemental sulphur with the use of Fe-EDTA complex. The possibility of obtaining fibrous filtering materials able to remove small concentrations of H2S from the air were described. The base of these materials is fibrous ion exchanger with Fe(III)- EDTA complex immobilized on their functional groups. The complex of trivalent iron converts hydrogen sulphide to elemental sulphur. Bivalent iron formed in the reaction is oxidized by the atmospheric oxygen, so complex of trivalent iron is continuously regenerated and the overall process can be accounted as pseudocatalytic. In the present paper properties of several fibrous catalysts based on ion exchangers with different chemical nature (weak acid,weak base and strong base) were described. It was shown that the main parameters affecting the process of catalytic oxidation are:concentration of hydrogen sulphide in the air, relative humidity of the purified air, the process time and the content of Fe-EDTA complex in the fibres. The data presented show that the filtering layers with anion exchange package are much more active in the catalytic processes of hydrogen sulphide removal than cation exchanger and inert materials. In the addition to the nature of the fibres relative air humidity is a critical factor determining efficiency of the material in the air purification from H2S. It was proved that the most promising carrier of the Fe-EDTA catalyst for hydrogen sulphide oxidation are Fiban A-6 and Fiban AK-22 fibres.
Abstract: One of the most important requirements for the
operation and planning activities of an electrical utility is the
prediction of load for the next hour to several days out, known as
short term load forecasting. This paper presents the development of
an artificial neural network based short-term load forecasting model.
The model can forecast daily load profiles with a load time of one
day for next 24 hours. In this method can divide days of year with
using average temperature. Groups make according linearity rate of
curve. Ultimate forecast for each group obtain with considering
weekday and weekend. This paper investigates effects of temperature
and humidity on consuming curve. For forecasting load curve of
holidays at first forecast pick and valley and then the neural network
forecast is re-shaped with the new data. The ANN-based load models
are trained using hourly historical. Load data and daily historical
max/min temperature and humidity data. The results of testing the
system on data from Yazd utility are reported.
Abstract: Temperature, relative humidity and overhygroscopic
moisture fields in a sandstone wall provided with interior thermal
insulation were calculated in order to assess the hygric performance
of the retrofitted wall. Computational simulations showed that during
the time period of 10 years which was subject of investigation no
overhygroscopic moisture appeared in the analyzed building
envelope so that it performed in a satisfactory way from the hygric
point of view.
Abstract: The study area receives a wide variety of wastes
generated by municipalities and the industries like paints and
pigments, metal processing industries, thermal power plants electroprocessing
industries etc. The Physico-chemical and structural
investigation of water from river Pandu indicated high level of
chlorides and calcium which made the water unsuitable for human
use. Algae like Cyclotella fumida, Asterionella Formosa,
Cladophora glomerata, Pediastrum simplex, Scenedesmus bijuga,
Cladophora glomerata were the dominant pollution tolerant species
recorded under these conditions. The sensitive and less abundant
species of algae included Spirogyra sps., Merismopedia sps. The
predominance colonies of Zygnema sps, Phormidium sps,
Mycrocystis aeruginosa, Merismopedia minima, Pandorina morum,
seems to correlate with high organic contents of Pandu river water.
This study assumes significance as some algae can be used as
bioindicators of water pollution and algal floral of a municipal drain
carrying waste effluents from industrial area Kanpur and discharge
them into the river Pandu flowing onto southern outskirts of Kanpur
city.
Abstract: This study investigated the climatic factors associated
with Influenza incidence in Nakhon Si Thammarat, Southern
Thailand. Climatic factors comprised of the amount of rainfall,
percent of rainy days, relative humidity, wind speed, maximum,
minimum temperatures and temperature difference. A multiple
stepwise regression technique was used to fit the statistical model.
The result showed that the temperature difference and percent of
rainy days were positively associated with Influenza incidence in
Nakhon Si Thammarat.
Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: The quality of Ribbed Smoked Sheets
(RSS) primarily based on color, dryness, and the presence or
absence of fungus and bubbles. This quality is strongly
influenced by the drying and fumigation process namely
smoking process. Smoking that is held in high temperature
long time will result scorched dark brown sheets, whereas if
the temperature is too low or slow drying rate would resulted
in less mature sheets and growth of fungus. Therefore need to
find the time and temperature for optimum quality of sheets.
Enhance, unmonitored heat and mass transfer during smoking
process lead to high losses of energy balance. This research
aims to generate simple empirical mathematical model
describing the effect of smoking time and temperature to RSS
quality of color, water content, fungus and bubbles. The
second goal of study was to analyze energy balance during
smoking process. Experimental study was conducted by
measuring temperature, residence time and quality parameters
of 16 sheets sample in smoking rooms. Data for energy
consumption balance such as mass of fuel wood, mass of
sheets being smoked, construction temperature, ambient
temperature and relative humidity were taken directly along
the smoking process. It was found that mathematical model
correlating smoking temperature and time with color is Color
= -169 - 0.184 T4 - 0.193 T3 - 0.160 0.405 T1 + T2 + 0.388 t1
+3.11 t2 + 3.92t3 + 0.215 t4 with R square 50.8% and with
moisture is Moisture = -1.40-0.00123 T4 + 0.00032 T3 +
0.00260 T2 - 0.00292 T1 - 0.0105 t1 + 0.0290 t2 + 0.0452 t3
+ 0.00061 t4 with R square of 49.9%. Smoking room energy
analysis found useful energy was 27.8%. The energy stored in
the material construction 7.3%. Lost of energy in conversion
of wood combustion, ventilation and others were 16.6%. The
energy flowed out through the contact of material construction
with the ambient air was found to be the highest contribution
to energy losses, it reached 48.3%.
Abstract: Transcription factor p53 has a powerful tumor
suppressing function that is associated with many cancers. However,
p53 of the molecular weight was higher make the limitation across to
skin or cell membrane. Thymidine dinucleotide (pTT), an
oligonucleotide, can activate the p53 transcription factor. pTT is a
hydrophilic and negative charge oligonucleotide, which delivery in to
cell membrane need an appropriate carrier. The aim of this study was
to improve the bioavailability of the nucleotide fragment, thymidine
dinucleotide (pTT), using elasic liposome carriers to deliver the drug
into the skin. The study demonstrate that dioleoylphosphocholine
(DOPC) incorporated with sodium cholate at molar ratio 1:1 can
archived the particle size about 220 nm. This elastic liposome could
penetration through skin from stratum corneum to whole epidermis by
confocal laser scanning microscopy (CLSM). Moreover, we observed
the the slight increase in generation of p53 by western blot.
Abstract: The benefits of rooftop greenery systems (such as
energy savings, reduction of greenhouse gas emission for mitigating
climate change and maintaining sustainable development, indoor
temperature control etc.) in buildings are well recognized, however
there remains very little research conducted for quantifying the
benefits in subtropical climates such as in Australia. This study
mainly focuses on measuring/determining temperature profile and air
conditioning energy savings by implementing rooftop greenery
systems in subtropical Central Queensland in Australia. An
experimental set-up was installed at Rockhampton campus of Central
Queensland University, where two standard shipping containers (6m
x 2.4m x 2.4m) were converted into small offices, one with green
roof and one without. These were used for temperature, humidity and
energy consumption data collection. The study found that an energy
savings of up to 11.70% and temperature difference of up to 4°C can
be achieved in March in subtropical Central Queensland climate in
Australia. It is expected that more energy can be saved in peak
summer days (December/February) as temperature difference
between green roof and non-green roof is higher in December-
February.
Abstract: The highly nonlinear characteristics of drying
processes have prompted researchers to seek new nonlinear control
solutions. However, the relation between the implementation
complexity, on-line processing complexity, reliability control
structure and controller-s performance is not well established. The
present paper proposes high performance nonlinear fuzzy controllers
for a real-time operation of a drying machine, being developed under
a consistent match between those issues. A PCI-6025E data
acquisition device from National Instruments® was used, and the
control system was fully designed with MATLAB® / SIMULINK
language. Drying parameters, namely relative humidity and
temperature, were controlled through MIMOs Hybrid Bang-bang+PI
(BPI) and Four-dimensional Fuzzy Logic (FLC) real-time-based
controllers to perform drying tests on biological materials. The
performance of the drying strategies was compared through several
criteria, which are reported without controllers- retuning. Controllers-
performance analysis has showed much better performance of FLC
than BPI controller. The absolute errors were lower than 8,85 % for
Fuzzy Logic Controller, about three times lower than the
experimental results with BPI control.
Abstract: The trial in the city, located 170 kilometers from the
Iranian city of Ahvaz was Omidiyeh. The main factor in this project
includes 4 levels in control (without hormones), use of hormones in
the seed, vegetative and flowering stage respectively. And sub-plots
included 3 varieties of vetch in three levels, with local names, was the
jewel in the study of light and Auxin in the vegetative and
reproductive different times in different varieties of vetch was
investigated. This test has been taken in the plots in a randomized
complete block with four replications. In order to study the effects of
the hormone Auxin in the growth stages (seed, vegetative and
flowering) to control (no hormone Auxin) on three local varieties of
vetch, the essence of light and plant height, number of pods per plant,
seed number The pods, seeds per plant, grain weight, grain yield,
plant dry weight and protein content were measured. Among the
vetch varieties for plant height, number of pods per plant, a seed per
plant, grain weight, grain yield, and plant dry weight and protein
levels of 1 percent of plant and seed number per pod per plant at 5%
level of There was no significant difference. Interactions for grain
yield per plant, grain yield and protein levels of 1 percent and the
number of seeds per pod and seed weight are significant differences
in levels 5 and plant height and plant dry weight of the interaction
were INFLUENCE There was no significant difference in them.
Abstract: This paper presents the experimental results of
comparison between leakage currents and discharge currents. The leakage currents were obtained on polluted porcelain insulator.
Whereas, the discharge currents were obtained on lightly artificial
polluted porcelain specimen. The conducted measurements were
leakage current or discharge current and applied voltage. The insulator or specimen was in a hermetically sealed chamber, and the
current waveforms were analyzed using FFT.
The result indicated that the leakage current (LC) on low RH condition the fifth harmonic would be visible, and followed by the
seventh harmonic. The insulator had capacitive property. Otherwise,
on 99% relative humidity, the fifth harmonic would also be visible,
and the phase angle reached up to 12.2 degree. Whereas, on discharge current, the third harmonic would be visible, and followed
by fifth harmonic. The third harmonic would increase as pressure reduced. On this condition, the specimen had a non-linear characteristics
Abstract: Dengue fever has become a major concern for health
authorities all over the world particularly in the tropical countries.
These countries, in particular are experiencing the most worrying
outbreak of dengue fever (DF) and dengue haemorrhagic fever
(DHF). The DF and DHF epidemics, thus, have become the main
causes of hospital admissions and deaths in Malaysia. This paper,
therefore, attempts to examine the environmental factors that may
influence the recent dengue outbreak. The aim of this study is twofold,
firstly is to establish a statistical model to describe the
relationship between the number of dengue cases and a range of
explanatory variables and secondly, to identify the lag operator for
explanatory variables which affect the dengue incidence the most.
The explanatory variables involved include the level of cloud cover,
percentage of relative humidity, amount of rainfall, maximum
temperature, minimum temperature and wind speed. The Poisson and
Negative Binomial regression analyses were used in this study. The
results of the analyses on the 915 observations (daily data taken from
July 2006 to Dec 2008), reveal that the climatic factors comprising of
daily temperature and wind speed were found to significantly
influence the incidence of dengue fever after 2 and 3 weeks of their
occurrences. The effect of humidity, on the other hand, appears to be
significant only after 2 weeks.
Abstract: Xanthan gum is one of the major commercial
biopolymers. Due to its excellent rheological properties xanthan gum
is used in many applications, mainly in food industry. Commercial
production of xanthan gum uses glucose as the carbon substrate;
consequently the price of xanthan production is high. One of the
ways to decrease xanthan price, is using cheaper substrate like
agricultural wastes. Iran is one of the biggest date producer countries.
However approximately 50% of date production is wasted annually.
The goal of this study is to produce xanthan gum from waste date
using Xanthomonas campestris PTCC1473 by submerged
fermentation. In this study the effect of three variables including
phosphor and nitrogen amount and agitation rate in three levels using
response surface methodology (RSM) has been studied. Results
achieved from statistical analysis Design Expert 7.0.0 software
showed that xanthan increased with increasing level of phosphor.
Low level of nitrogen leaded to higher xanthan production. Xanthan
amount, increasing agitation had positive influence. The statistical
model identified the optimum conditions nitrogen amount=3.15g/l,
phosphor amount=5.03 g/l and agitation=394.8 rpm for xanthan. To
model validation, experiments in optimum conditions for xanthan
gum were carried out. The mean of result for xanthan was 6.72±0.26.
The result was closed to the predicted value by using RSM.