Abstract: The Mobile Ad-hoc Network (MANET) is a collection of self-configuring and rapidly deployed mobile nodes (routers) without any central infrastructure. Routing is one of the potential issues. Many routing protocols are reported but it is difficult to decide which one is best in all scenarios. In this paper on demand routing protocols DSR and DYMO based on IEEE 802.11 DCF MAC protocol are examined and characteristic summary of these routing protocols is presented. Their performance is analyzed and compared on performance measuring metrics throughput, dropped packets due to non availability of routes, duplicate RREQ generated for route discovery and normalized routing load by varying CBR data traffic load using QualNet 5.0.2 network simulator.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: Delay-Tolerant Networks (DTNs) are sparse, wireless
networks where disconnections are common due to host mobility and
low node density. The Message Ferrying (MF) scheme is a mobilityassisted
paradigm to improve connectivity in DTN-like networks. A
ferry or message ferry is a special node in the network which has
a per-determined route in the deployed area and relays messages
between mobile hosts (MHs) which are intermittently connected.
Increased contact opportunities among mobile hosts and the ferry
improve the performance of the network, both in terms of message
delivery ratio and average end-end delay. However, due to the inherent
mobility of mobile hosts and pre-determined periodicity of the
message ferry, mobile hosts may often -miss- contact opportunities
with a ferry. In this paper, we propose the combination of stationary
ferry access points (FAPs) with MF routing to increase contact
opportunities between mobile hosts and the MF and consequently
improve the performance of the DTN. We also propose several
placement models for deploying FAPs on MF routes. We evaluate the
performance of the FAP placement models through comprehensive
simulation. Our findings show that FAPs do improve the performance
of MF-assisted DTNs and symmetric placement of FAPs outperforms
other placement strategies.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: In this paper, we proposed a new routing protocol for
Unmanned Aerial Vehicles (UAVs) that equipped with directional
antenna. We named this protocol Directional Optimized Link State
Routing Protocol (DOLSR). This protocol is based on the well
known protocol that is called Optimized Link State Routing Protocol
(OLSR). We focused in our protocol on the multipoint relay (MPR)
concept which is the most important feature of this protocol. We
developed a heuristic that allows DOLSR protocol to minimize
the number of the multipoint relays. With this new protocol the
number of overhead packets will be reduced and the End-to-End
delay of the network will also be minimized. We showed through
simulation that our protocol outperformed Optimized Link State
Routing Protocol, Dynamic Source Routing (DSR) protocol and Ad-
Hoc On demand Distance Vector (AODV) routing protocol in
reducing the End-to-End delay and enhancing the overall
throughput. Our evaluation of the previous protocols was based
on the OPNET network simulation tool.
Abstract: This work proposes an accurate crosstalk noise estimation method in the presence of multiple RLC lines for the use in design automation tools. This method correctly models the loading effects of non switching aggressors and aggressor tree branches using resistive shielding effect and realistic exponential input waveforms. Noise peak and width expressions have been derived. The results obtained are at good agreement with SPICE results. Results show that average error for noise peak is 4.7% and for the width is 6.15% while allowing a very fast analysis.
Abstract: This paper presents the experimental results of silicone rubber polymer insulators for 22 kV systems under salt water dip wheel test based on IEC 62217. Straight shed silicone rubber polymer insulators having leakage distance 685 mm were tested continuously 30,000 cycles. One test cycle includes 4 positions, energized, de-energized, salt water dip and deenergized, respectively. For one test cycle, each test specimen remains stationary for about 40 second in each position and takes 8 second for rotate to next position. By visual observation, sever surface erosion was observed on the trunk near the energized end of tested specimen. Puncture was observed on the upper shed near the energized end. In addition, decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Furthermore, chemical analysis by ATR-FTIR was conducted in order to elucidate the chemical change of tested specimens comparing with new specimen.
Abstract: Wind farms (WFs) with high level of penetration are
being established in power systems worldwide more rapidly than
other renewable resources. The Independent System Operator (ISO),
as a policy maker, should propose appropriate places for WF
installation in order to maximize the benefits for the investors. There
is also a possibility of congestion relief using the new installation of
WFs which should be taken into account by the ISO when proposing
the locations for WF installation. In this context, efficient wind farm
(WF) placement method is proposed in order to reduce burdens on
congested lines. Since the wind speed is a random variable and load
forecasts also contain uncertainties, probabilistic approaches are used
for this type of study. AC probabilistic optimal power flow (P-OPF)
is formulated and solved using Monte Carlo Simulations (MCS). In
order to reduce computation time, point estimate methods (PEM) are
introduced as efficient alternative for time-demanding MCS.
Subsequently, WF optimal placement is determined using generation
shift distribution factors (GSDF) considering a new parameter
entitled, wind availability factor (WAF). In order to obtain more
realistic results, N-1 contingency analysis is employed to find the
optimal size of WF, by means of line outage distribution factors
(LODF). The IEEE 30-bus test system is used to show and compare
the accuracy of proposed methodology.
Abstract: The need in cognitive radio system for a simple, fast, and independent technique to sense the spectrum occupancy has led to the energy detection approach. Energy detector is known by its dependency on noise variation in the system which is one of its major drawbacks. In this paper, we are aiming to improve its performance by utilizing a weighted collaborative spectrum sensing, it is similar to the collaborative spectrum sensing methods introduced previously in the literature. These weighting methods give more improvement for collaborative spectrum sensing as compared to no weighting case. There is two method proposed in this paper: the first one depends on the channel status between each sensor and the primary user while the second depends on the value of the energy measured in each sensor.
Abstract: The authors present a mixed method for reducing the order of the large-scale dynamic systems. In this method, the denominator polynomial of the reduced order model is obtained by using the modified pole clustering technique while the coefficients of the numerator are obtained by Pade approximations. This method is conceptually simple and always generates stable reduced models if the original high-order system is stable. The proposed method is illustrated with the help of the numerical examples taken from the literature.
Abstract: In this paper, a double balanced radio frequency multiplier
is presented which is customized for transmitted reference
ultra wideband (UWB) receivers. The multiplier uses 90nm model
parameters and exploits compensating transistors to provide controllable
gain for a Gilbert core. After performing periodic and quasiperiodic
non linear analyses the RF mixer (multiplier) achieves a
voltage conversion gain of 16 dB and a DSB noise figure of 8.253
dB with very low power consumption. A high degree of LO to RF
isolation (in the range of -94dB), RF to IF isolation (in the range of
-95dB) and LO to IF isolation (in the range of -143dB) is expected
for this design with an input-referred IP3 point of -1.93 dBm and an
input referred 1 dB compression point of -10.67dBm. The amount of
noise at the output is 7.7 nV/√Hz when the LO input is driven by
a 10dBm signal. The mixer manifests better results when compared
with other reported multiplier circuits and its Zero-IF performance
ensures its applicability as TR-UWB multipliers.
Abstract: Transmission and distribution lines are vital links between the generating unit and consumers. They are exposed to atmosphere, hence chances of occurrence of fault in transmission line is very high which has to be immediately taken care of in order to minimize damage caused by it. In this paper Discrete wavelet transform of voltage signals at the two ends of transmission lines have been analyzed. The transient energy of the detail information of level five is calculated for different fault conditions. It is observed that the variation of transient energy of healthy and faulted line can give important information which can be very useful in classifying and locating the fault.
Abstract: A frequency grouping approach for multi-channel
instantaneous blind source separation (I-BSS) of convolutive
mixtures is proposed for a lower net residual inter-symbol
interference (ISI) and inter-channel interference (ICI) than the
conventional short-time Fourier transform (STFT) approach. Starting
in the time domain, STFTs are taken with overlapping windows to
convert the convolutive mixing problem into frequency domain
instantaneous mixing. Mixture samples at the same frequency but
from different STFT windows are grouped together forming unique
frequency groups.
The individual frequency group vectors are input to the I-BSS
algorithm of choice, from which the output samples are dispersed
back to their respective STFT windows. After applying the inverse
STFT, the resulting time domain signals are used to construct the
complete source estimates via the weighted overlap-add method
(WOLA). The proposed algorithm is tested for source deconvolution
given two mixtures, and simulated along with the STFT approach to
illustrate its superiority for fairly motionless sources.
Abstract: The wireless adhoc network is comprised of wireless
node which can move freely and are connected among themselves
without central infrastructure. Due to the limited transmission range
of wireless interfaces, in most cases communication has to be relayed
over intermediate nodes. Thus, in such multihop network each node
(also called router) is independent, self-reliant and capable to route
the messages over the dynamic network topology. Various protocols
are reported in this field and it is very difficult to decide the best one.
A key issue in deciding which type of routing protocol is best for
adhoc networks is the communication overhead incurred by the
protocol. In this paper STAR a table driven and DSR on demand
protocols based on IEEE 802.11 are analyzed for their performance
on different performance measuring metrics versus varying traffic
CBR load using QualNet 5.0.2 network simulator.
Abstract: This paper presents an application of power line
carrier (PLC) for electrical power telemetering. This system has a
special capability of transmitting the measured values to a centralized
computer via power lines. The PLC modem as a passive high-pass
filter is designed for transmitting and receiving information. Its
function is to send the information carrier together with transmitted
data by superimposing it on the 50 Hz power frequency signal. A
microcontroller is employed to function as the main processing of the
modem. It is programmed for PLC control and interfacing with other
devices. Each power meter, connected via a PLC modem, is assigned
with a unique identification number (address) for distinguishing each
device from one another.
Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: Recently, Genetic Algorithms (GA) and Differential
Evolution (DE) algorithm technique have attracted considerable
attention among various modern heuristic optimization techniques.
Since the two approaches are supposed to find a solution to a given
objective function but employ different strategies and computational
effort, it is appropriate to compare their performance. This paper
presents the application and performance comparison of DE and GA
optimization techniques, for flexible ac transmission system
(FACTS)-based controller design. The design objective is to enhance
the power system stability. The design problem of the FACTS-based
controller is formulated as an optimization problem and both the PSO
and GA optimization techniques are employed to search for optimal
controller parameters. The performance of both optimization
techniques has been compared. Further, the optimized controllers are
tested on a weekly connected power system subjected to different
disturbances, and their performance is compared with the
conventional power system stabilizer (CPSS). The eigenvalue
analysis and non-linear simulation results are presented and
compared to show the effectiveness of both the techniques in
designing a FACTS-based controller, to enhance power system
stability.
Abstract: This study reports the preparation of soft magnetic ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213 mm and, with a thickness of approximately 22 μm 2 μm. The microstructure and magnetic properties of the ribbons were characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide ribbon, the magnetic responses are not uniformly distributed. To understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: This paper studies a vital issue in wireless
communications, which is the transmission of images over Wireless
Personal Area Networks (WPANs) through the Bluetooth network. It
presents a simple method to improve the efficiency of error control
code of old Bluetooth versions over mobile WPANs through
Interleaved Error Control Code (IECC) technique. The encoded
packets are interleaved by simple block interleaver. Also, the paper
presents a chaotic interleaving scheme as a tool against bursts of
errors which depends on the chaotic Baker map. Also, the paper
proposes using the chaotic interleaver instead of traditional block
interleaver with Forward Error Control (FEC) scheme. A comparison
study between the proposed and standard techniques for image
transmission over a correlated fading channel is presented.
Simulation results reveal the superiority of the proposed chaotic
interleaving scheme to other schemes. Also, the superiority of FEC
with proposed chaotic interleaver to the conventional interleavers
with enhancing the security level with chaotic interleaving packetby-
packet basis.
Abstract: This study adopted previous fault patterns, results of
detection analysis, historical records and data, and experts-
experiences to establish fuzzy principles and estimate the failure
probability index of components of a power transformer. Considering
that actual parameters and limiting conditions of parameters may
differ, this study used the standard data of IEC, IEEE, and CIGRE as
condition parameters. According to the characteristics of each
condition parameter, relative degradation was introduced to reflect the
degree of influence of the factors on the transformer condition. The
method of fuzzy mathematics was adopted to determine the
subordinate function of the transformer condition. The calculation
used the Matlab Fuzzy Tool Box to select the condition parameters of
coil winding, iron core, bushing, OLTC, insulating oil and other
auxiliary components and factors (e.g., load records, performance
history, and maintenance records) of the transformer to establish the
fuzzy principles. Examples were presented to support the rationality
and effectiveness of the evaluation method of power transformer
performance conditions, as based on fuzzy comprehensive evaluation.