Abstract: A design problem of non-uniform circular antenna arrays for maximum reduction of both the side lobe level (SLL) and first null beam width (FNBW) is dealt with. This problem is modeled as a simple optimization problem. The method of Firefly algorithm (FFA) is used to determine an optimal set of current excitation weights and antenna inter-element separations that provide radiation pattern with maximum SLL reduction and much improvement on FNBW as well. Circular array antenna laid on x-y plane is assumed. FFA is applied on circular arrays of 8-, 10-, and 12- elements. Various simulation results are presented and hence performances of side lobe and FNBW are analyzed. Experimental results show considerable reductions of both the SLL and FNBW with respect to those of the uniform case and some standard algorithms GA, PSO and SA applied to the same problem.
Abstract: This paper describes optimal thinning of an Elliptical
Cylindrical Array (ECA) of uniformly excited isotropic antennas
which can generate directive beam with minimum relative Side Lobe
Level (SLL). The Particle Swarm Optimization (PSO) method, which
represents a new approach for optimization problems in
electromagnetic, is used in the optimization process. The PSO is used
to determine the optimal set of ‘ON-OFF’ elements that provides a
radiation pattern with maximum SLL reduction. Optimization is done
without prefixing the value of First Null Beam Width (FNBW). The
variation of SLL with element spacing of thinned array is also
reported. Simulation results show that the number of array elements
can be reduced by more than 50% of the total number of elements in
the array with a simultaneous reduction in SLL to less than -27dB.
Abstract: In this paper, an optimal design of linear phase digital
high pass finite impulse response (FIR) filter using Particle Swarm
Optimization with Constriction Factor and Inertia Weight Approach
(PSO-CFIWA) has been presented. In the design process, the filter
length, pass band and stop band frequencies, feasible pass band and
stop band ripple sizes are specified. FIR filter design is a multi-modal
optimization problem. The conventional gradient based optimization
techniques are not efficient for digital filter design. Given the filter
specifications to be realized, the PSO-CFIWA algorithm generates a
set of optimal filter coefficients and tries to meet the ideal frequency
response characteristic. In this paper, for the given problem, the
designs of the optimal FIR high pass filters of different orders have
been performed. The simulation results have been compared to those
obtained by the well accepted algorithms such as Parks and
McClellan algorithm (PM), genetic algorithm (GA). The results
justify that the proposed optimal filter design approach using PSOCFIWA
outperforms PM and GA, not only in the accuracy of the
designed filter but also in the convergence speed and solution
quality.
Abstract: This paper presents an optimal design of linear phase
digital high pass finite impulse response (FIR) filter using Improved
Particle Swarm Optimization (IPSO). In the design process, the filter
length, pass band and stop band frequencies, feasible pass band and
stop band ripple sizes are specified. FIR filter design is a multi-modal
optimization problem. An iterative method is introduced to find the
optimal solution of FIR filter design problem. Evolutionary
algorithms like real code genetic algorithm (RGA), particle swarm
optimization (PSO), improved particle swarm optimization (IPSO)
have been used in this work for the design of linear phase high pass
FIR filter. IPSO is an improved PSO that proposes a new definition
for the velocity vector and swarm updating and hence the solution
quality is improved. A comparison of simulation results reveals the
optimization efficacy of the algorithm over the prevailing
optimization techniques for the solution of the multimodal, nondifferentiable,
highly non-linear, and constrained FIR filter design
problems.
Abstract: The resistive-inductive-capacitive behavior of long
interconnects which are driven by CMOS gates are presented in this
paper. The analysis is based on the ¤Ç-model of a RLC load and is
developed for submicron devices. Accurate and analytical
expressions for the output load voltage, the propagation delay and the
short circuit power dissipation have been proposed after solving a
system of differential equations which accurately describe the
behavior of the circuit. The effect of coupling capacitance between
input and output and the short circuit current on these performance
parameters are also incorporated in the proposed model. The
estimated proposed delay and short circuit power dissipation are in
very good agreement with the SPICE simulation with average
relative error less than 6%.
Abstract: This work proposes an accurate crosstalk noise estimation method in the presence of multiple RLC lines for the use in design automation tools. This method correctly models the loading effects of non switching aggressors and aggressor tree branches using resistive shielding effect and realistic exponential input waveforms. Noise peak and width expressions have been derived. The results obtained are at good agreement with SPICE results. Results show that average error for noise peak is 4.7% and for the width is 6.15% while allowing a very fast analysis.
Abstract: This paper demonstrates the application of craziness based particle swarm optimization (CRPSO) technique for designing the 8th order low pass Infinite Impulse Response (IIR) filter. CRPSO, the much improved version of PSO, is a population based global heuristic search algorithm which finds near optimal solution in terms of a set of filter coefficients. Effectiveness of this algorithm is justified with a comparative study of some well established algorithms, namely, real coded genetic algorithm (RGA) and particle swarm optimization (PSO). Simulation results affirm that the proposed algorithm CRPSO, outperforms over its counterparts not only in terms of quality output i.e. sharpness at cut-off, pass band ripple, stop band ripple, and stop band attenuation but also in convergence speed with assured stability.
Abstract: Fast delay estimation methods, as opposed to
simulation techniques, are needed for incremental performance
driven layout synthesis. On-chip inductive effects are becoming
predominant in deep submicron interconnects due to increasing clock
speed and circuit complexity. Inductance causes noise in signal
waveforms, which can adversely affect the performance of the circuit
and signal integrity. Several approaches have been put forward which
consider the inductance for on-chip interconnect modelling. But for
even much higher frequency, of the order of few GHz, the shunt
dielectric lossy component has become comparable to that of other
electrical parameters for high speed VLSI design. In order to cope up
with this effect, on-chip interconnect has to be modelled as
distributed RLCG line. Elmore delay based methods, although
efficient, cannot accurately estimate the delay for RLCG interconnect
line. In this paper, an accurate analytical delay model has been
derived, based on first and second moments of RLCG
interconnection lines. The proposed model considers both the effect
of inductance and conductance matrices. We have performed the
simulation in 0.18μm technology node and an error of as low as less
as 5% has been achieved with the proposed model when compared to
SPICE. The importance of the conductance matrices in interconnect
modelling has also been discussed and it is shown that if G is
neglected for interconnect line modelling, then it will result an delay
error of as high as 6% when compared to SPICE.