Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: Analysis of the elastic scattering of protons on 6,7Li
nuclei has been done in the framework of the optical model at the
beam energies up to 50 MeV. Differential cross sections for the 6,7Li +
p scattering were measured over the proton laboratory–energy range
from 400 to 1050 keV. The elastic scattering of 6,7Li+p data at
different proton incident energies have been analyzed using singlefolding
model. In each case the real potential obtained from the
folding model was supplemented by a phenomenological imaginary
potential, and during the fitting process the real potential was
normalized and the imaginary potential optimized. Normalization
factor NR is calculated in the range between 0.70 and 0.84.
Abstract: The mineral having chemical compositional formula MgAl2O4 is called “spinel". The ferrites crystallize in spinel structure are known as spinel-ferrites or ferro-spinels. The spinel structure has a fcc cage of oxygen ions and the metallic cations are distributed among tetrahedral (A) and octahedral (B) interstitial voids (sites). The X-ray diffraction (XRD) intensity of each Bragg plane is sensitive to the distribution of cations in the interstitial voids of the spinel lattice. This leads to the method of determination of distribution of cations in the spinel oxides through XRD intensity analysis. The computer program for XRD intensity analysis has been developed in C language and also tested for the real experimental situation by synthesizing the spinel ferrite materials Mg0.6Zn0.4AlxFe2- xO4 and characterized them by X-ray diffractometry. The compositions of Mg0.6Zn0.4AlxFe2-xO4(x = 0.0 to 0.6) ferrites have been prepared by ceramic method and powder X-ray diffraction patterns were recorded. Thus, the authenticity of the program is checked by comparing the theoretically calculated data using computer simulation with the experimental ones. Further, the deduced cation distributions were used to fit the magnetization data using Localized canting of spins approach to explain the “recovery" of collinear spin structure due to Al3+ - substitution in Mg-Zn ferrites which is the case if A-site magnetic dilution and non-collinear spin structure. Since the distribution of cations in the spinel ferrites plays a very important role with regard to their electrical and magnetic properties, it is essential to determine the cation distribution in spinel lattice.
Abstract: This paper proposes a new parameter identification
method based on Linear Fractional Transformation (LFT). It is
assumed that the target linear system includes unknown parameters.
The parameter deviations are separated from a nominal system via
LFT, and identified by organizing I/O signals around the separated
deviations of the real system. The purpose of this paper is to apply LFT
to simultaneously identify the parameter deviations in systems with
fewer outputs than unknown parameters. As a fundamental example,
this method is implemented to one degree of freedom vibratory system.
Via LFT, all physical parameters were simultaneously identified in this
system. Then, numerical simulations were conducted for this system to
verify the results. This study shows that all the physical parameters of a
system with fewer outputs than unknown parameters can be effectively
identified simultaneously using LFT.
Abstract: The charge-exchange xenon (CEX) ion generated by ion thruster can backflow to the surface of spacecraft and threaten to the safety of spacecraft operation. In order to evaluate the effects of the induced plasma environment in backflow regions on the spacecraft, we designed a spherical single Langmuir probe of 5.8cm in diameter for measuring low-density plasma parameters in backflow region of ion thruster. In practice, the tests are performed in a two-dimensional array (40cm×60cm) composed of 20 sites. The experiment results illustrate that the electron temperature ranges from 3.71eV to 3.96eV, with the mean value of 3.82eV and the standard deviation of 0.064eV. The electron density ranges from 8.30×1012/m3 to 1.66×1013/m3, with the mean value of 1.30×1013/m3 and the standard deviation of 2.15×1012/m3. All data is analyzed according to the “ideal" plasma conditions of Maxwellian distributions.
Abstract: A new conserving approach in the context of Immersed Boundary Method (IBM) is presented to simulate one dimensional, incompressible flow in a moving boundary problem. The method employs control volume scheme to simulate the flow field. The concept of ghost node is used at the boundaries to conserve the mass and momentum equations. The Present method implements the conservation laws in all cells including boundary control volumes. Application of the method is studied in a test case with moving boundary. Comparison between the results of this new method and a sharp interface (Image Point Method) IBM algorithm shows a well distinguished improvement in both pressure and velocity fields of the present method. Fluctuations in pressure field are fully resolved in this proposed method. This approach expands the IBM capability to simulate flow field for variety of problems by implementing conservation laws in a fully Cartesian grid compared to other conserving methods.
Abstract: We studied the evolution of elliptic heavy SF6
gas cylinder surrounded by air when accelerated by a planar
Mach 1.25 shock. A multiple dynamics imaging technology has
been used to obtain one image of the experimental initial
conditions and five images of the time evolution of elliptic
cylinder. We compared the width and height of the circular and
two kinds of elliptic gas cylinders, and analyzed the vortex
strength of the elliptic ones. Simulations are in very good
agreement with the experiments, but due to the different initial
gas cylinder shapes, a certain difference of the initial density
peak and distribution exists between the circular and elliptic
gas cylinders, and the latter initial state is more sensitive and
more inenarrable.
Abstract: Free convection effects and heat transfer due to a pulsating point heat source embedded in an infinite, fluid saturated, porous dusty medium are studied analytically. Both velocity and temperature fields are discussed in the form of series expansions in the Rayleigh number, for both the fluid and particle phases based on the mean heat generation rate from source and on the permeability of the porous dusty medium. This study is carried out by assuming the Rayleigh number small and the validity of Darcy-s law. Analytical expressions for both phases are obtained for second order mean in both velocity and temperature fields and evolution of different wave patterns are observed in the fluctuating part. It has been observed that, at the vicinity of the origin, the second order mean flow is influenced only by relaxation time of dust particles and not by dust concentration.
Abstract: We constructed a method of phase unwrapping for a typical wave-front by utilizing the maximizer of the posterior marginal (MPM) estimate corresponding to equilibrium statistical mechanics of the three-state Ising model on a square lattice on the basis of an analogy between statistical mechanics and Bayesian inference. We investigated the static properties of an MPM estimate from a phase diagram using Monte Carlo simulation for a typical wave-front with synthetic aperture radar (SAR) interferometry. The simulations clarified that the surface-consistency conditions were useful for extending the phase where the MPM estimate was successful in phase unwrapping with a high degree of accuracy and that introducing prior information into the MPM estimate also made it possible to extend the phase under the constraint of the surface-consistency conditions with a high degree of accuracy. We also found that the MPM estimate could be used to reconstruct the original wave-fronts more smoothly, if we appropriately tuned hyper-parameters corresponding to temperature to utilize fluctuations around the MAP solution. Also, from the viewpoint of statistical mechanics of the Q-Ising model, we found that the MPM estimate was regarded as a method for searching the ground state by utilizing thermal fluctuations under the constraint of the surface-consistency condition.
Abstract: Flow movement in unsaturated soil can be expressed
by a partial differential equation, named Richards equation. The
objective of this study is the finding of an appropriate implicit
numerical solution for head based Richards equation. Some of the
well known finite difference schemes (fully implicit, Crank Nicolson
and Runge-Kutta) have been utilized in this study. In addition, the
effects of different approximations of moisture capacity function,
convergence criteria and time stepping methods were evaluated. Two
different infiltration problems were solved to investigate the
performance of different schemes. These problems include of vertical
water flow in a wet and very dry soils. The numerical solutions of
two problems were compared using four evaluation criteria and the
results of comparisons showed that fully implicit scheme is better
than the other schemes. In addition, utilizing of standard chord slope
method for approximation of moisture capacity function, automatic
time stepping method and difference between two successive
iterations as convergence criterion in the fully implicit scheme can
lead to better and more reliable results for simulation of fluid
movement in different unsaturated soils.
Abstract: This paper presents a finite point method based on
directional derivatives for diffusion equation on 2D scattered points.
To discretize the diffusion operator at a given point, a six-point stencil
is derived by employing explicit numerical formulae of directional
derivatives, namely, for the point under consideration, only five
neighbor points are involved, the number of which is the smallest for
discretizing diffusion operator with first-order accuracy. A method for
selecting neighbor point set is proposed, which satisfies the solvability
condition of numerical derivatives. Some numerical examples are
performed to show the good performance of the proposed method.
Abstract: Artificial atoms are growing fields of interest due to their physical and optoelectronicapplications. The absorption spectra of the proposed artificial atom inpresence of Tera-Hertz field is investigated theoretically. We use the non-perturbativeFloquet theory and finite difference method to study the electronic structure of ArtificialAtom. The effect of static electric field on the energy levels of artificial atom is studied.The effect of orientation of static electric field on energy levels and diploe matrix elementsis also highlighted.
Abstract: The algorithms of convex hull have been extensively studied in literature, principally because of their wide range of applications in different areas. This article presents an efficient algorithm to construct approximate convex hull from a set of n points in the plane in O(n + k) time, where k is the approximation error control parameter. The proposed algorithm is suitable for applications preferred to reduce the computation time in exchange of accuracy level such as animation and interaction in computer graphics where rapid and real-time graphics rendering is indispensable.
Abstract: This study investigates a voltage-controllable liquid crystals lens with a Fresnel zone electrode. When applying a proper voltage on the liquid crystal cell, a Fresnel-zone-distributed electric field is induced to direct liquid crystals aligned in a concentric structure. Owing to the concentrically aligned liquid crystals, a Fresnel lens is formed. We probe the Fresnel liquid crystal lens using a polarized incident beam with a wavelength of 632.8 nm, finding that the diffraction efficiency depends on the applying voltage. A remarkable diffraction efficiency of ~39.5 % is measured at the voltage of 0.9V. Additionally, a dual focus lens is fabricated by attaching a plane-convex lens to the Fresnel liquid crystals cell. The Fresnel LC lens and the dual focus lens may be applied for DVD/CD pick-up head, confocal microscopy system, or electrically-controlling optical systems.
Abstract: Applying corona wind as a novel technique can lead
to a great level of heat and mass transfer augmentation by using very
small amount of energy. Enhancement of forced flow evaporation
rate by applying electric field (corona wind) has been experimentally
evaluated in this study. Corona wind produced by a fine wire
electrode which is charged with positive high DC voltage impinges
to water surface and leads to evaporation enhancement by disturbing
the saturated air layer over water surface. The study was focused on
the effect of corona wind velocity, electrode spacing and air flow
velocity on the level of evaporation enhancement. Two sets of
experiments, i.e. with and without electric field, have been
conducted. Data obtained from the first experiment were used as
reference for evaluation of evaporation enhancement at the presence
of electric field. Applied voltages ranged from corona threshold
voltage to spark over voltage at 1 kV increments. The results showed
that corona wind has great enhancement effect on water evaporation
rate, but its effectiveness gradually diminishes by increasing air flow
velocity. Maximum enhancements were 7.3 and 3.6 for air velocities
of 0.125 and 1.75 m/s, respectively.
Abstract: The presented paper is related to the design methods and neutronic characterization of the reactivity control system in the large power unit of Generation IV Gas cooled Fast Reactor – GFR2400. The reactor core is based on carbide pin fuel type with the application of refractory metallic liners used to enhance the fission product retention of the SiCcladding. The heterogeneous design optimization of control rod is presented and the results of rods worth and their interferences in a core are evaluated. In addition, the idea of reflector removal as an additive reactivity management option is investigated and briefly described.
Abstract: Speckle phenomena results from when coherent
radiation is reflected from a rough surface. Characterizing the speckle
strongly depends on the measurement condition and experimental
setup. In this paper we report the experimental results produced with
different parameters in the setup. We investigated the factors which
affects the speckle contrast, such as, F-number, gamma value and
exposure time of the camera, rather than geometric factors like the
distance between the projector lens to the screen, the viewing distance,
etc. The measurement results show that the speckle contrast decreases
by decreasing F-number, by increasing gamma value, and slightly
affects by exposure time of the camera and the gain value of the
camera.
Abstract: Let p be a prime number such that p ≡ 1(mod 4), say
p = 1+4k for a positive integer k. Let P = 2k + 1 and Q = k2.
In this paper, we consider the integer solutions of the Pell equation
x2-Py2 = Q over Z and also over finite fields Fp. Also we deduce
some relations on the integer solutions (xn, yn) of it.
Abstract: High Pressure Raman scattering measurements of KDP:Mn were performed at room temperatures. The X-ray powder diffraction patterns taken at room temperature by Rietveld refinement showed that doped samples of KDP-Mn have the same tetragonal structure of a pure KDP crystal, but with a contraction of the crystalline cell. The behavior of the Raman spectra, in particular the emergence of a new modes at 330 cm-1, indicates that KDP:Mn undergoes a structural phase transition with onset at around 4 GP. First principle density-functional theory (DFT) calculations indicate that tetrahedral rotation with pressure is predominantly around the c crystalline direction. Theoretical results indicates that pressure induced tetrahedral rotations leads to change tetrahedral neighborhood, activating librations/bending modes observed for high pressure phase of KDP:Mn with stronger Raman activity.
Abstract: In this paper, we propose a novel metal oxide
semiconductor field effect transistor with L-shaped channel structure
(LMOS), and several type of L-shaped structures are also designed,
studied and compared with the conventional MOSFET device for the
same average gate length (Lavg). The proposed device electrical
characteristics are analyzed and evaluated by three dimension (3-D)
ISE-TCAD simulator. It can be confirmed that the LMOS devices
have higher on-state drain current and both lower drain-induced
barrier lowering (DIBL) and subthreshold swing (S.S.) than its
conventional counterpart has. In addition, the transconductance and
voltage gain properties of the LMOS are also improved.