Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: The trend of growing density on chips has increases not
only the temperature in chips but also the gradient of the temperature
depending on locations. In this paper, we propose the balanced skew
tree generation technique for minimizing the clock skew that is
affected by the temperature gradients on chips. We calculate the
interconnect delay using Elmore delay equation, and find out the
optimal balanced clock tree by modifying the clock trees generated
through the Deferred Merge Embedding(DME) algorithm. The
experimental results show that the distance variance of clock insertion
points with and without considering the temperature gradient can be
lowered below 54% and we confirm that the skew is remarkably
decreased after applying the proposed technique.
Abstract: Here, in this work we study correspondence the energy density New agegraphic and the energy density Gauss- Bonnet models in flat universe. We reconstruct Λ and Λ ω for them with 0 ( ) 0 h a t = a t .
Abstract: We have considered an unmagnetized dusty plasma system consisting of ions obeying superthermal distribution and strongly coupled negatively charged dust. We have used reductive perturbation method and derived the Kordeweg-de Vries-Burgers (KdV-Burgers) equation. The behavior of the shock waves in the plasma has been investigated.
Abstract: This calculation focus on the effect of exchange
interaction J and Coulomb interaction U on spin magnetic moments
(ms) of MnO by using the local spin density approximation plus the
Coulomb interaction (LSDA+U) method within full potential linear
muffin-tin orbital (FP-LMTO). Our calculated results indicated that
the spin magnetic moments correlated to J and U. The relevant
results exhibited the increasing spin magnetic moments with
increasing exchange interaction and Coulomb interaction.
Furthermore, equations of spin magnetic moment, which h good
correspondence to the experimental data 4.58μB, are defined ms =
0.11J +4.52μB and ms = 0.03U+4.52μB. So, the relation of J and U
parameter is obtained, it is obviously, J = -0.249U+1.346 eV.
Abstract: We have solved the Burgers-Fisher (BF) type equations,
with time-dependent coefficients of convection and reaction terms,
by using the auxiliary equation method. A class of solitary wave
solutions are obtained, and some of which are derived for the first
time. We have studied the effect of variable coefficients on physical
parameters (amplitude and velocity) of solitary wave solutions. In
some cases, the BF equations could be solved for arbitrary timedependent
coefficient of convection term.
Abstract: The class of geometric deformable models, so-called
level sets, has brought tremendous impact to medical imagery. In
this paper we present yet another application of level sets to medical
imaging. The method we give here will in a way modify the speed
term in the standard level sets equation of motion. To do so we
build a potential based on the distance and the gradient of the
image we study. In turn the potential gives rise to the force field:
F~F(x, y) = P
∀(p,q)∈I
((x, y) - (p, q)) |ÔêçI(p,q)|
|(x,y)-(p,q)|
2 . The direction
and intensity of the force field at each point will determine the
direction of the contour-s evolution. The images we used to test
our method were produced by the Univesit'e de Sherbrooke-s PET
scanners.
Abstract: This paper presents the vibrations suppression of a thermoelastic beam subject to sudden heat input by a distributed piezoelectric actuators. An optimization problem is formulated as the minimization of a quadratic functional in terms of displacement and velocity at a given time and with the least control effort. The solution method is based on a combination of modal expansion and variational approaches. The modal expansion approach is used to convert the optimal control of distributed parameter system into the optimal control of lumped parameter system. By utilizing the variational approach, an explicit optimal control law is derived and the determination of the corresponding displacement and velocity is reduced to solving a set of ordinary differential equations.
Abstract: In this paper two mathematical models for definition of gas accidental escape localization in the gas pipelines are suggested. The first model was created for leak localization in the horizontal branched pipeline and second one for leak detection in inclined section of the main gas pipeline. The algorithm of leak localization in the branched pipeline did not demand on knowledge of corresponding initial hydraulic parameters at entrance and ending points of each sections of pipeline. For detection of the damaged section and then leak localization in this section special functions and equations have been constructed. Some results of calculations for compound pipelines having two, four and five sections are presented. Also a method and formula for the leak localization in the simple inclined section of the main gas pipeline are suggested. Some results of numerical calculations defining localization of gas escape for the inclined pipeline are presented.
Abstract: This paper presents a generalized form of the
mechanistic deconvolution technique (GMD) to modeling image sensors applicable in various pan–tilt planes of view. The mechanistic deconvolution technique (UMD) is modified with the
given angles of a pan–tilt plane of view to formulate constraint parameters and characterize distortion effects, and thereby, determine
the corrected image data. This, as a result, does not require experimental setup or calibration. Due to the mechanistic nature of
the sensor model, the necessity for the sensor image plane to be
orthogonal to its z-axis is eliminated, and it reduces the dependency on image data. An experiment was constructed to evaluate the
accuracy of a model created by GMD and its insensitivity to changes in sensor properties and in pan and tilt angles. This was compared
with a pre-calibrated model and a model created by UMD using two sensors with different specifications. It achieved similar accuracy
with one-seventh the number of iterations and attained lower mean error by a factor of 2.4 when compared to the pre-calibrated and
UMD model respectively. The model has also shown itself to be robust and, in comparison to pre-calibrated and UMD model, improved the accuracy significantly.
Abstract: Saturated two-phase fluid flows are often subject to
pressure induced oscillations. Due to compressibility the vapor
bubbles act as a spring with an asymmetric non-linear characteristic.
The volume of the vapor bubbles increases or decreases differently if
the pressure fluctuations are compressing or expanding;
consequently, compressing pressure fluctuations in a two-phase pipe
flow cause less displacement in the direction of the pipe flow than
expanding pressure fluctuations. The displacement depends on the
ratio of liquid to vapor, the ratio of pressure fluctuations over average
pressure and on the exciting frequency of the pressure fluctuations.
In addition, pressure fluctuations in saturated vapor bubbles cause
condensation and evaporation within the bubbles and change
periodically the ratio between liquid to vapor, and influence the
dynamical parameters for the oscillation. The oscillations are
conforming to an isenthalpic process at constant enthalpy with no
heat transfer and no exchange of work.
The paper describes the governing non-linear equation for twophase
fluid oscillations with condensation and evaporation, and
presents steady state approximate solutions for free and for pressure
induced oscillations. Resonance criteria and stability are discussed.
Abstract: The evaluation of unit cell neutronic parameters and
lifetime for some innovant reactors without on sit-refuling will be
held in this work. the behavior of some small and medium reactors
without on site refueling with triso and cermet fuel. For the FBNR
long life except we propose to change the enrichment of the Cermet
MFE to 9%. For the AFPR reactor we can see that the use of the
Cermet MFE can extend the life of this reactor but to maintain the
same life period for AFPR-SC we most use burnup poison to have the
same slope for Kinf (Burnup). PFPWR50 cell behaves almost in
same way using both fuels Cermet and TRISO. So we can conclude
that PFPWR50 reactor, with CERMET Fuel, is kept among the long
cycle reactors and with the new configuration we avoid subcriticality
at the beginning of cycle. The evaluation of unit cell neutronic
parameters reveals a good agreement with the goal of BWR-PB
concept. It is found out that the Triso fuel assembly lifetime can be
extended for a reasonably long period without being refueled,
approximately up to 48GWd/t burnup. Using coated particles fuels
with the Cermet composition can be more extended the fuel assembly
life time, approximately 52 GWd/t.
Abstract: The Navier–Stokes equations for unsteady, incompressible, viscous fluids in the axisymmetric coordinate system are solved using a control volume method. The volume-of-fluid (VOF) technique is used to track the free-surface of the liquid. Model predictions are in good agreement with experimental measurements. It is found that the dynamic processes after impact are sensitive to the initial droplet velocity and the liquid pool depth. The time evolution of the crown height and diameter are obtained by numerical simulation. The critical We number for splashing (Wecr) is studied for Oh (Ohnesorge) numbers in the range of 0.01~0.1; the results compares well with those of the experiments.
Abstract: A code has been developed in Mathematica using
Direct Simulation Monte Carlo (DSMC) technique. The code was
tested for 2-D air flow around a circular cylinder. Same geometry
and flow properties were used in FLUENT 6.2 for comparison. The
results obtained from Mathematica simulation indicated significant
agreement with FLUENT calculations, hence providing insight into
particle nature of fluid flows.
Abstract: In this paper, a two-dimensional mathematical model is developed for estimating the extent of inland inundation due to Indonesian tsunami of 2004 along the coastal belts of Peninsular Malaysia and Thailand. The model consists of the shallow water equations together with open and coastal boundary conditions. In order to route the water wave towards the land, the coastal boundary is treated as a time dependent moving boundary. For computation of tsunami inundation, the initial tsunami wave is generated in the deep ocean with the strength of the Indonesian tsunami of 2004. Several numerical experiments are carried out by changing the slope of the beach to examine the extent of inundation with slope. The simulated inundation is found to decrease with the increase of the slope of the orography. Correlation between inundation / recession and run-up are found to be directly proportional to each other.
Abstract: This paper presents a methodical approach for designing and optimizing process parameters in oil blending industries. Twenty seven replicated experiments were conducted for production of A-Z crown super oil (SAE20W/50) employing L9 orthogonal array to establish process response parameters. Power law model was fitted to experimental data and the obtained model was optimized applying the central composite design (CCD) of response surface methodology (RSM). Quadratic model was found to be significant for production of A-Z crown supper oil. The study recognized and specified four new lubricant formulations that conform to ISO oil standard in the course of analyzing the batch productions of A-Z crown supper oil as: L1: KV = 21.8293Cst, BS200 = 9430.00Litres, Ad102=11024.00Litres, PVI = 2520 Litres, L2: KV = 22.513Cst, BS200 = 12430.00 Litres, Ad102 = 11024.00 Litres, PVI = 2520 Litres, L3: KV = 22.1671Cst, BS200 = 9430.00 Litres, Ad102 = 10481.00 Litres, PVI= 2520 Litres, L4: KV = 22.8605Cst, BS200 = 12430.00 Litres, Ad102 = 10481.00 Litres, PVI = 2520 Litres. The analysis of variance showed that quadratic model is significant for kinematic viscosity production while the R-sq value statistic of 0.99936 showed that the variation of kinematic viscosity is due to its relationship with the control factors. This study therefore resulted to appropriate blending proportions of lubricants base oil and additives and recommends the optimal kinematic viscosity of A-Z crown super oil (SAE20W/50) to be 22.86Cst.
Abstract: We investigated statistical performance of Bayesian inference using maximum entropy and MAP estimation for several models which approximated wave-fronts in remote sensing using SAR interferometry. Using Monte Carlo simulation for a set of wave-fronts generated by assumed true prior, we found that the method of maximum entropy realized the optimal performance around the Bayes-optimal conditions by using model of the true prior and the likelihood representing optical measurement due to the interferometer. Also, we found that the MAP estimation regarded as a deterministic limit of maximum entropy almost achieved the same performance as the Bayes-optimal solution for the set of wave-fronts. Then, we clarified that the MAP estimation perfectly carried out phase unwrapping without using prior information, and also that the MAP estimation realized accurate phase unwrapping using conjugate gradient (CG) method, if we assumed the model of the true prior appropriately.
Abstract: Structural and UV/Visible optical properties can be
useful to describe a material for the CIGS solar cell active layer,
therefore, this work demonstrates the properties like surface
morphology, X-ray Photoelectron Spectroscopy (XPS) bonding
energy (EB) core level spectra, UV/Visible absorption spectra,
refractive index (n), optical energy band (Eg), reflection spectra for
the Cu25 (In16Ga9) Se40Te10 (CIGST-1) and Cu20 (In14Ga9) Se45Te12
(CIGST-2) chalcogenide compositions. Materials have been
exhibited homogenous surface morphologies, broading /-or diffusion
of bonding energy peaks relative elemental values and a high
UV/Visible absorption tendency in the wave length range 400 nm-
850 nm range with the optical energy band gaps 1.37 and 1.42
respectively. Subsequently, UV/Visible reflectivity property in the
wave length range 250 nm to 320 nm for these materials has also
been discussed.
Abstract: In the context of channel coding, the Generalized Belief Propagation (GBP) is an iterative algorithm used to recover the transmission bits sent through a noisy channel. To ensure a reliable transmission, we apply a map on the bits, that is called a code. This code induces artificial correlations between the bits to send, and it can be modeled by a graph whose nodes are the bits and the edges are the correlations. This graph, called Tanner graph, is used for most of the decoding algorithms like Belief Propagation or Gallager-B. The GBP is based on a non unic transformation of the Tanner graph into a so called region-graph. A clear advantage of the GBP over the other algorithms is the freedom in the construction of this graph. In this article, we explain a particular construction for specific graph topologies that involves relevant performance of the GBP. Moreover, we investigate the behavior of the GBP considered as a dynamic system in order to understand the way it evolves in terms of the time and in terms of the noise power of the channel. To this end we make use of classical measures and we introduce a new measure called the hyperspheres method that enables to know the size of the attractors.
Abstract: A robust AUSM+ upwind discretisation scheme has been developed to simulate multiphase flow using consistent spatial discretisation schemes and a modified low-Mach number diffusion term. The impact of the selection of an interfacial pressure model has also been investigated. Three representative test cases have been simulated to evaluate the accuracy of the commonly-used stiffenedgas equation of state with respect to the IAPWS-IF97 equation of state for water. The algorithm demonstrates a combination of robustness and accuracy over a range of flow conditions, with the stiffened-gas equation tending to overestimate liquid temperature and density profiles.