Abstract: Texture information plays increasingly an important
role in remotely sensed imagery classification and many pattern
recognition applications. However, the selection of relevant textural
features to improve this classification accuracy is not a straightforward
task. This work investigates the effectiveness of two Mutual
Information Feature Selector (MIFS) algorithms to select salient
textural features that contain highly discriminatory information for
multispectral imagery classification. The input candidate features are
extracted from a SPOT High Resolution Visible(HRV) image using
Wavelet Transform (WT) at levels (l = 1,2).
The experimental results show that the selected textural features
according to MIFS algorithms make the largest contribution to
improve the classification accuracy than classical approaches such
as Principal Components Analysis (PCA) and Linear Discriminant
Analysis (LDA).
Abstract: Requirements that should be met when determining the regimes of circuits with variable elements are formulated. The interpretation of the variations in the regimes, based on projective geometry, enables adequate expressions for determining and comparing the regimes to be derived. It is proposed to use as the parameters of a generalized equivalent generator of an active two-pole with changeable resistor such load current and voltage which provide the current through this resistor equal to zero.
Abstract: Many real-world optimization problems involve multiple conflicting objectives and the use of evolutionary algorithms to solve the problems has attracted much attention recently. This paper investigates the application of multi-objective optimization technique for the design of a Thyristor Controlled Series Compensator (TCSC)-based controller to enhance the performance of a power system. The design objective is to improve both rotor angle stability and system voltage profile. A Genetic Algorithm (GA) based solution technique is applied to generate a Pareto set of global optimal solutions to the given multi-objective optimisation problem. Further, a fuzzy-based membership value assignment method is employed to choose the best compromise solution from the obtained Pareto solution set. Simulation results are presented to show the effectiveness and robustness of the proposed approach.
Abstract: In this paper, the detection of a fault in the Global Positioning System (GPS) measurement is addressed. The class of faults considered is a bias in the GPS pseudorange measurements. This bias is modeled as an unknown constant. The fault could be the result of a receiver fault or signal fault such as multipath error. A bias bank is constructed based on set of possible fault hypotheses. Initially, there is equal probability of occurrence for any of the biases in the bank. Subsequently, as the measurements are processed, the probability of occurrence for each of the biases is sequentially updated. The fault with a probability approaching unity will be declared as the current fault in the GPS measurement. The residual formed from the GPS and Inertial Measurement Unit (IMU) measurements is used to update the probability of each fault. Results will be presented to show the performance of the presented algorithm.
Abstract: To compress, improve bit error performance and also enhance 2D images, a new scheme, called Iterative Cellular-Turbo System (IC-TS) is introduced. In IC-TS, the original image is partitioned into 2N quantization levels, where N is denoted as bit planes. Then each of the N-bit-plane is coded by Turbo encoder and transmitted over Additive White Gaussian Noise (AWGN) channel. At the receiver side, bit-planes are re-assembled taking into consideration of neighborhood relationship of pixels in 2-D images. Each of the noisy bit-plane values of the image is evaluated iteratively using IC-TS structure, which is composed of equalization block; Iterative Cellular Image Processing Algorithm (ICIPA) and Turbo decoder. In IC-TS, there is an iterative feedback link between ICIPA and Turbo decoder. ICIPA uses mean and standard deviation of estimated values of each pixel neighborhood. It has extra-ordinary satisfactory results of both Bit Error Rate (BER) and image enhancement performance for less than -1 dB Signal-to-Noise Ratio (SNR) values, compared to traditional turbo coding scheme and 2-D filtering, applied separately. Also, compression can be achieved by using IC-TS systems. In compression, less memory storage is used and data rate is increased up to N-1 times by simply choosing any number of bit slices, sacrificing resolution. Hence, it is concluded that IC-TS system will be a compromising approach in 2-D image transmission, recovery of noisy signals and image compression.
Abstract: Power system state estimation is the process of
calculating a reliable estimate of the power system state vector
composed of bus voltages' angles and magnitudes from telemetered
measurements on the system. This estimate of the state vector
provides the description of the system necessary for the operation
and security monitoring. Many methods are described in the
literature for solving the state estimation problem, the most important
of which are the classical weighted least squares method and the nondeterministic
genetic based method; however both showed
drawbacks. In this paper a modified version of the genetic
algorithm power system state estimation is introduced, Sensitivity of
the proposed algorithm to genetic operators is discussed, the
algorithm is applied to case studies and finally it is compared with
the classical weighted least squares method formulation.
Abstract: This study reports the preparation of soft magnetic
ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213
mm and, with a thickness of approximately 22 μm ± 2 μm. The microstructure and magnetic properties of the ribbons were
characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material
properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic
measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide
ribbon, the magnetic responses are not uniformly distributed. To
understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a
ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: This paper proposes an application of the differential
evolution (DE) algorithm for solving the economic dispatch problem
(ED). Furthermore, the regenerating population procedure added to
the conventional DE in order to improve escaping the local minimum
solution. To test performance of DE algorithm, three thermal
generating units with valve-point loading effects is used for testing.
Moreover, investigating the DE parameters is presented. The
simulation results show that the DE algorithm, which had been
adjusted parameters, is better convergent time than other optimization
methods.
Abstract: This paper shows the potential system benefits of
simple tracking solar system using a stepper motor and light sensor.
This method is increasing power collection efficiency by developing
a device that tracks the sun to keep the panel at a right angle to its
rays. A solar tracking system is designed, implemented and
experimentally tested. The design details and the experimental results
are shown.
Abstract: Truncated multiplier is a good candidate for digital
signal processing (DSP) applications including finite impulse
response (FIR) and discrete cosine transform (DCT). Through
truncated multiplier a significant reduction in Field Programmable
Gate Array (FPGA) resources can be achieved. This paper presents
for the first time a comparison of resource utilization of Spartan-3AN
and Virtex-5 implementation of standard and truncated multipliers
using Very High Speed Integrated Circuit Hardware Description
Language (VHDL). The Virtex-5 FPGA shows significant
improvement as compared to Spartan-3AN FPGA device. The
Virtex-5 FPGA device shows better performance with a percentage
ratio of number of occupied slices for standard to truncated
multipliers is increased from 40% to 73.86% as compared to Spartan-
3AN is decreased from 68.75% to 58.78%. Results show that the
anomaly in Spartan-3AN FPGA device average connection and
maximum pin delay have been efficiently reduced in Virtex-5 FPGA
device.
Abstract: This paper presents a speed sensorless direct torque
control scheme using space vector modulation (DTC-SVM) for
permanent magnet synchronous motor (PMSM) drive based a Model
Reference Adaptive System (MRAS) algorithm and stator resistance
estimator. The MRAS is utilized to estimate speed and stator
resistance and compensate the effects of parameter variation on stator
resistance, which makes flux and torque estimation more accurate
and insensitive to parameter variation. In other hand the use of SVM
method reduces the torque ripple while achieving a good dynamic
response. Simulation results are presented and show the effectiveness
of the proposed method.
Abstract: In this paper application of artificial intelligence for
baby and children caring is studied. Then a new idea for injury
prevention and safety announcement is presented by using digital
image processing. The paper presents the structure of the proposed
system. The system determines the possibility of the dangers for
children and babies in yards, gardens and swimming pools or etc. In
the presented idea, multi camera System is used and receiver videos
are processed to find the hazardous areas then the entrance of
children and babies in the determined hazardous areas are analyzed.
In this condition the system does the programmed action capture,
produce alarm or tone or send message.
Abstract: A conventional image posterization method
occasionally fails to preserve the shape and color of objects due to the
uneffective color reduction. This paper proposes a new image
posterizartion method by using modified color quantization for
preserving the shape and color of objects and color contrast
enhancement for improving lightness contrast and saturation.
Experiment results show that our proposed method can provide
visually more satisfactory posterization result than that of the
conventional method.
Abstract: A novel three-phase active power filter (APF) circuit with photovoltaic (PV) system to improve the quality of service and to reduce the capacity of energy storage capacitor is presented. The energy balance concept and sampling technique were used to simplify the calculation algorithm for the required utility source current and to control the voltage of the energy storage capacitor. The feasibility was verified by using the Pspice simulations and experiments. When the APF mode was used during non-operational period, not only the utilization rate, power factor and power quality could be improved, but also the capacity of energy storage capacitor could sparing. As the results, the advantages of the APF circuit are simplicity of control circuits, low cost, and good transient response.
Abstract: Multiplication algorithms have considerable effect on
processors performance. A new high-speed, low-power
multiplication algorithm has been presented using modified Dadda
tree structure. Three important modifications have been implemented
in inner product generation step, inner product reduction step and
final addition step. Optimized algorithms have to be used into basic
computation components, such as multiplication algorithms. In this
paper, we proposed a new algorithm to reduce power, delay, and
transistor count of a multiplication algorithm implemented using low
power modified counter. This work presents a novel design for
Dadda multiplication algorithms. The proposed multiplication
algorithm includes structured parts, which have important effect on
inner product reduction tree. In this paper, a 1.3V, 64-bit carry hybrid
adder is presented for fast, low voltage applications. The new 64-bit
adder uses a new circuit to implement the proposed carry hybrid
adder. The new adder using 80 nm CMOS technology has been
implemented on 700 MHz clock frequency. The proposed
multiplication algorithm has achieved 14 percent improvement in
transistor count, 13 percent reduction in delay and 12 percent
modification in power consumption in compared with conventional
designs.
Abstract: The distance protection mainly the impedance relay which is considered as the main protection for transmission lines can be subjected to impedance measurement error which is, mainly, due to the fault resistance and to the power fluctuation. Thus, the impedance relay may not operate for a short circuit at the far end of the protected line (case of the under reach) or operates for a fault beyond its protected zone (case of overreach). In this paper, an approach to fault detection by a distance protection, which distinguishes between the faulty conditions and the effect of overload operation mode, has been developed. This approach is based on the symmetrical components; mainly the negative sequence, and it is taking into account both the effect of fault resistance and the overload situation which both have an effect upon the reliability of the protection in terms of dependability for the former and security for the latter.
Abstract: The evolutionary design of electronic circuits, or
evolvable hardware, is a discipline that allows the user to
automatically obtain the desired circuit design. The circuit
configuration is under the control of evolutionary algorithms. Several
researchers have used evolvable hardware to design electrical
circuits. Every time that one particular algorithm is selected to carry
out the evolution, it is necessary that all its parameters, such as
mutation rate, population size, selection mechanisms etc. are tuned in
order to achieve the best results during the evolution process. This
paper investigates the abilities of evolution strategy to evolve digital
logic circuits based on programmable logic array structures when
different mutation rates are used. Several mutation rates (fixed and
variable) are analyzed and compared with each other to outline the
most appropriate choice to be used during the evolution of
combinational logic circuits. The experimental results outlined in this
paper are important as they could be used by every researcher who
might need to use the evolutionary algorithm to design digital logic
circuits.
Abstract: In this paper present a sensorless maximum wind power extraction for variable speed constant frequency (VSCF) wind power generation systems with a doubly-fed induction generators (DFIG), to ensure stability and to impose the ideal feedback control solution despite of model uncertainties , using the principles of an active and reactive power controller (DPC) a robust sliding mode power control has been proposed to guarantees fast response times and precise control actions for control the active and reactive power independently. The simulation results in MATLAB/Simulink platform confirmed the good dynamic performance of power control approach for DFIGbased variable speed wind turbines.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: Electric vehicle (EV) is one of the effective solutions to
control emission of greenhouses gases in the world. It is of interest
for future transportation due to its sustainability and efficiency by
automotive manufacturers. Various electrical motors have been used
for propulsion system of electric vehicles in last decades. In this
paper brushed DC motor, Induction motor (IM), switched reluctance
motor (SRM) and brushless DC motor (BLDC) are simulated and
compared. BLDC motor is recommended for high performance
electric vehicles. PWM switching technique is implemented for speed
control of BLDC motor. Behavior of different modes of PWM speed
controller of BLDC motor are simulated in MATLAB/SIMULINK.
BLDC motor characteristics are compared and discussed for various
PWM switching modes under normal and inverter fault conditions.
Comparisons and discussions are verified through simulation results.