Abstract: In this paper we present a novel method, which
reduces the computational complexity of abrupt cut detection. We
have proposed fast algorithm, where the similarity of frames within
defined step is evaluated instead of comparing successive frames.
Based on the results of simulation on large video collection, the
proposed fast algorithm is able to achieve 80% reduction of needed
frames comparisons compared to actually used methods without the
shot cut detection accuracy degradation.
Abstract: For sterilization of Phalaenopsis culture medium without autoclaving, selected single sterilizing agents and in combinations were added to a 25ml Hyponex medium in a 120ml glass container. Treated liquid and solid media, supplemented with sterilizing agents, were compared to a control medium, autoclaved at 121°C for 15min. It was found that 90(L of 10% povidone-iodine, 150(L of 5.25% sodium hypochlorite, 150(L of 2% mercurochrome, 90(L of 2.5% iodine + 2.5% potassium iodine in combination with 10% providone-iodine (1:3) and 30(L of 2.5% iodine + 2.5% potassium iodide in combination with 2% mercurochrome showed 100% sterile conditions in liquid medium but provided 75, 100, 50, 75 and 80% sterile conditions, respectively, in solid medium. For growth of Phalaenopsis protocorms, 90(L of 10% povidone-iodine in liquid Hyponex medium gave the comparable growth of protocorms to control medium while 150(L of 5.25% sodium hypochlorite in solid medium provided the promising growth of protocorms. Growth of protocorms, whole fresh weight, numbers of leaf and root, root length and number of protocorm-like bodies, was discussed.
Abstract: Estimation of natural frequency of structures is very
important and isn-t usually calculated simply and sometimes
complicated. Lack of knowledge about that caused hard damage and
hazardous effects.
In this paper, with using from two different models in FEM
method and based on hydrodynamic mass of fluids, natural frequency
of an especial bearing (Fig. 1) in an electric field (or, a periodic
force) is calculated in different stiffness and different geometric. In
final, the results of two models and analytical solution are compared.
Abstract: In this paper the complete rotor system including
elastic shaft with distributed mass, allowing for the effects of oil film
in bearings. Also, flexibility of foundation is modeled. As a whole
this article is a relatively complete research in modeling and
vibration analysis of rotor considering gyroscopic effect, damping,
dependency of stiffness and damping coefficients on frequency and
solving the vibration equations including these parameters. On the
basis of finite element method and utilizing four element types
including element of shaft, disk, bearing and foundation and using
MATLAB, a computer program is written. So the responses in
several cases and considering different effects are obtained. Then the
results are compared with each other, with exact solutions and results
of other papers.
Abstract: This experiment was conducted in attempt of
improving hydrodynamic efficiency of the propulsion mechanism by
installing a spring to the wing so that the opening angle of the wing in
one stroke can be changed automatically, compared to the existing
method of fixed maximum opening angle in Weis-Fogh type ship
propulsion mechanism. Average thrust coefficient was almost fixed
with all velocity ratio with the prototype, but with the spring type,
thrust coefficient increased sharply as velocity ratio increased.
Average propulsive efficiency was larger with bigger opening angle in
the prototype, but in the spring type, the one with smaller spring
coefficient had larger value. In the range over 1.0 in velocity ratio
where big thrust can be generated, spring type had more than twice of
propulsive efficiency increase compared to the prototype.
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.
Abstract: This paper gives an introduction to Web mining, then
describes Web Structure mining in detail, and explores the data
structure used by the Web. This paper also explores different Page
Rank algorithms and compare those algorithms used for Information
Retrieval. In Web Mining, the basics of Web mining and the Web
mining categories are explained. Different Page Rank based
algorithms like PageRank (PR), WPR (Weighted PageRank), HITS
(Hyperlink-Induced Topic Search), DistanceRank and DirichletRank
algorithms are discussed and compared. PageRanks are calculated for
PageRank and Weighted PageRank algorithms for a given hyperlink
structure. Simulation Program is developed for PageRank algorithm
because PageRank is the only ranking algorithm implemented in the
search engine (Google). The outputs are shown in a table and chart
format.
Abstract: In this study the mixed mode fracture mechanics
parameters were investigated for high tensile steel butt welded joint
based on modified Arcan test and finite element analysis was used to
evaluate the effect of crack length on fracture criterion. The nondimensional
stress intensity factors, strain energy release rates and Jintegral
energy on crack tip were obtained for various in-plane
loading combinations on Arcan specimen starting from pure mode-I
to pure mode-II loading conditions. The specimen and apparatus were
modeled by finite element method and analyzed under various
loading angles (between 0 to 90 degrees with 15 degree interval) to
simulate the pure mode-I, II and mixed mode fracture. Since the
analytical results are independent from elasticity modules for
isotropic materials, therefore the results in elastic fields can be used
for Arcan specimens. The main objective of this study was to
evaluate the geometric calibration factors for modified Arcan test
specimen in order to obtain fracture toughness under mixed mode
loading conditions.
Abstract: Construction of portable device for fast analysis of energetic materials is described in this paper. The developed analytical system consists of two main parts: a miniaturized microcolumn liquid chromatograph of unique construction and original chemiluminescence detector. This novel portable device is able to determine selectively most of nitramine- and nitroester-based explosives as well as inorganic nitrates at trace concentrations in water or soil extracts in less than 8 minutes.
Abstract: Most of the academics connect a theory of
multiculturalism with globalization and limit it by last decades of
20th century. However, Kazakh society encountered with this
problem when the Soviet-s rule emerged. As a result of repression,
the Second World War, development of virgin lands representatives
of more than 100 nationalities lives in Kazakhstan. Communist
ideology propagandized internationalism, which would defined
principles of multicultural community but a common ideology
demands a single culture. As a result multicultural society in the
USSR developed under control of Russian culture. Education in the
USSR was conducted in two departments: autochthonous and
Russian. Autochthonous education narrowed student capabilities.
Also because of soviet ideology science was conducted in Russian
Universities provided education in Russian and all science literature
were in Russian. Exceptions were humanitarian fields where Kazakh
departments were admitted. Naturally non-Kazakhs studied in
Russian departments, moreover Kazakhs preferred to study in
Russian as most do nowadays preferring English. As a result Kazakh
society consisted of Kazakhs, Kazakhs who recognized Russian as a
mother tongue and other nationalities who were also Russian
speakers. This aspect continues to distinguish particular qualities of
multicultural community in Kazakhstan.
Abstract: Hazardous Material transportation by road is coupled
with inherent risk of accidents causing loss of lives, grievous injuries,
property losses and environmental damages. The most common type
of hazmat road accident happens to be the releases (78%) of
hazardous substances, followed by fires (28%), explosions (14%) and
vapour/ gas clouds (6 %.).
The paper is discussing initially the probable 'Impact Zones'
likely to be caused by one flammable (LPG) and one toxic (ethylene
oxide) chemicals being transported through a sizable segment of a
State Highway connecting three notified Industrial zones in Surat
district in Western India housing 26 MAH industrial units. Three
'hotspots' were identified along the highway segment depending on
the particular chemical traffic and the population distribution within
500 meters on either sides. The thermal radiation and explosion
overpressure have been calculated for LPG / Ethylene Oxide BLEVE
scenarios along with toxic release scenario for ethylene oxide.
Besides, the dispersion calculations for ethylene oxide toxic release
have been made for each 'hotspot' location and the impact zones
have been mapped for the LOC concentrations. Subsequently, the
maximum Initial Isolation and the protective zones were calculated
based on ERPG-3 and ERPG-2 values of ethylene oxide respectively
which are estimated taking the worst case scenario under worst
weather conditions. The data analysis will be helpful to the local
administration in capacity building with respect to rescue /
evacuation and medical preparedness and quantitative inputs to
augment the District Offsite Emergency Plan document.
Abstract: Warranty is a powerful marketing tool for the
manufacturer and a good protection for both the manufacturer and the
customer. However, warranty always involves additional costs to the
manufacturer, which depend on product reliability characteristics and
warranty parameters. This paper presents an approach to optimisation
of warranty parameters for known product failure distribution to
reduce the warranty costs to the manufacturer while retaining the
promotional function of the warranty. Combination free replacement
and pro-rata warranty policy is chosen as a model and the length of
free replacement period and pro-rata policy period are varied, as well
as the coefficients that define the pro-rata cost function. Multiparametric
warranty optimisation is done by using genetic algorithm.
Obtained results are guideline for the manufacturer to choose the
warranty policy that minimises the costs and maximises the profit.
Abstract: This paper presents ageing experiments controlled by the evolution of junction parameters. The deterioration of the device is related to high injection effects which modified the transport mechanisms in the space charge region of the junction. Physical phenomena linked to the degradation of junction parameters that affect the devices reliability are reported and discussed. We have used the method based on numerical analysis of experimental current-voltage characteristic of the junction, in order to extract the electrical parameters. The simultaneous follow-up of the evolutions of the series resistance and of the transition voltage allow us to introduce a new parameter for reliability evaluation.
Abstract: We proposed a technique to identify road traffic
congestion levels from velocity of mobile sensors with high accuracy
and consistent with motorists- judgments. The data collection utilized
a GPS device, a webcam, and an opinion survey. Human perceptions
were used to rate the traffic congestion levels into three levels: light,
heavy, and jam. Then the ratings and velocity were fed into a
decision tree learning model (J48). We successfully extracted vehicle
movement patterns to feed into the learning model using a sliding
windows technique. The parameters capturing the vehicle moving
patterns and the windows size were heuristically optimized. The
model achieved accuracy as high as 99.68%. By implementing the
model on the existing traffic report systems, the reports will cover
comprehensive areas. The proposed method can be applied to any
parts of the world.
Abstract: In this paper we investigate the electrical
characteristics of a new structure of gate all around strained silicon
nanowire field effect transistors (FETs) with dual dielectrics by
changing the radius (RSiGe) of silicon-germanium (SiGe) wire and
gate dielectric. Indeed the effect of high-κ dielectric on Field Induced
Barrier Lowering (FIBL) has been studied. Due to the higher electron
mobility in tensile strained silicon, the n-type FETs with strained
silicon channel have better drain current compare with the pure Si
one. In this structure gate dielectric divided in two parts, we have
used high-κ dielectric near the source and low-κ dielectric near the
drain to reduce the short channel effects. By this structure short
channel effects such as FIBL will be reduced indeed by increasing
the RSiGe, ID-VD characteristics will be improved. The leakage
current and transfer characteristics, the threshold-voltage (Vt), the
drain induced barrier height lowering (DIBL), are estimated with
respect to, gate bias (VG), RSiGe and different gate dielectrics. For
short channel effects, such as DIBL, gate all around strained silicon
nanowire FET have similar characteristics with the pure Si one while
dual dielectrics can improve short channel effects in this structure.
Abstract: Different problems may causes distortion of the rotor,
and hence vibration, which is the most severe damage of the turbine
rotors. In many years different techniques have been developed for
the straightening of bent rotors. The method for straightening can be
selected according to initial information from preliminary inspections
and tests such as nondestructive tests, chemical analysis, run out tests
and also a knowledge of the shaft material. This article covers the
various causes of excessive bends and then some applicable common
straightening methods are reviewed. Finally, hot spotting is opted for
a particular bent rotor. A 325 MW steam turbine rotor is modeled and
finite element analyses are arranged to investigate this straightening
process. Results of experimental data show that performing the exact
hot spot straightening process reduced the bending of the rotor
significantly.
Abstract: This paper is concerned with the delay-distributiondependent
stability criteria for bidirectional associative memory
(BAM) neural networks with time-varying delays. Based on the
Lyapunov-Krasovskii functional and stochastic analysis approach,
a delay-probability-distribution-dependent sufficient condition is derived
to achieve the globally asymptotically mean square stable of
the considered BAM neural networks. The criteria are formulated in
terms of a set of linear matrix inequalities (LMIs), which can be
checked efficiently by use of some standard numerical packages. Finally,
a numerical example and its simulation is given to demonstrate
the usefulness and effectiveness of the proposed results.
Abstract: A complex valued neural network is a neural network
which consists of complex valued input and/or weights and/or thresholds
and/or activation functions. Complex-valued neural networks
have been widening the scope of applications not only in electronics
and informatics, but also in social systems. One of the most important
applications of the complex valued neural network is in signal
processing. In Neural networks, generalized mean neuron model
(GMN) is often discussed and studied. The GMN includes a new
aggregation function based on the concept of generalized mean of all
the inputs to the neuron. This paper aims to present exhaustive results
of using Generalized Mean Neuron model in a complex-valued neural
network model that uses the back-propagation algorithm (called
-Complex-BP-) for learning. Our experiments results demonstrate the
effectiveness of a Generalized Mean Neuron Model in a complex
plane for signal processing over a real valued neural network. We
have studied and stated various observations like effect of learning
rates, ranges of the initial weights randomly selected, error functions
used and number of iterations for the convergence of error required on
a Generalized Mean neural network model. Some inherent properties
of this complex back propagation algorithm are also studied and
discussed.
Abstract: Overcurrent (OC) relays are the major protection
devices in a distribution system. The operating time of the OC relays
are to be coordinated properly to avoid the mal-operation of the
backup relays. The OC relay time coordination in ring fed
distribution networks is a highly constrained optimization problem
which can be stated as a linear programming problem (LPP). The
purpose is to find an optimum relay setting to minimize the time of
operation of relays and at the same time, to keep the relays properly
coordinated to avoid the mal-operation of relays.
This paper presents two phase simplex method for optimum time
coordination of OC relays. The method is based on the simplex
algorithm which is used to find optimum solution of LPP. The
method introduces artificial variables to get an initial basic feasible
solution (IBFS). Artificial variables are removed using iterative
process of first phase which minimizes the auxiliary objective
function. The second phase minimizes the original objective function
and gives the optimum time coordination of OC relays.
Abstract: The reduction in vehicle exhaust emissions achieved
in the last two decades is offset by the growth in traffic, as well as by
changes in the composition of emitted pollutants. The present
investigation illustrates the emissions of in-use gasoline and diesel
passenger cars using the official European driving cycle and the
ARTEMIS real-world driving cycle. It was observed that some of the
vehicles do not comply with the corresponding regulations.
Significant differences in emissions were observed between driving
cycles. Not all pollutants showed a tendency to decrease from Euro 3
to Euro 5.