Abstract: This paper presents a new sufficient condition for the
existence, uniqueness and global asymptotic stability of the equilibrium point for Cohen-Grossberg neural networks with multiple time delays. The results establish a relationship between the network parameters
of the neural system independently of the delay parameters. The results are also compared with the previously reported results in
the literature.
Abstract: The objective of this work is to show a procedure for
mesh generation in a fluidized bed using large eddy simulations
(LES) of a filtered two-fluid model. The experimental data were
obtained by [1] in a laboratory fluidized bed. Results show that it is
possible to use mesh with less cells as compared to RANS turbulence
model with granular kinetic theory flow (KTGF). Also, the numerical
results validate the experimental data near wall of the bed, which
cannot be predicted by RANS.model.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production.
Abstract: Multi-loop (De-centralized) Proportional-Integral-
Derivative (PID) controllers have been used extensively in process
industries due to their simple structure for control of multivariable
processes. The objective of this work is to design multiple-model
adaptive multi-loop PID strategy (Multiple Model Adaptive-PID)
and neural network based multi-loop PID strategy (Neural Net
Adaptive-PID) for the control of multivariable system. The first
method combines the output of multiple linear PID controllers,
each describing process dynamics at a specific level of operation.
The global output is an interpolation of the individual multi-loop
PID controller outputs weighted based on the current value of the
measured process variable. In the second method, neural network
is used to calculate the PID controller parameters based on the
scheduling variable that corresponds to major shift in the process
dynamics. The proposed control schemes are simple in structure with
less computational complexity. The effectiveness of the proposed
control schemes have been demonstrated on the CSTR process,
which exhibits dynamic non-linearity.
Abstract: THEOS is the first earth observation spacecraft of Thailand which was launched on the 1st October 2008 and is currently operated by GISTDA. The transfer phase has been performed by Astrium Flight Dynamics team leading to a hand over to GISTDA teams starting mid-October 2008. The THEOS spacecraft-s orbit is LEO and has the same repetitivity (14+5/26) as the SPOT spacecraft, i.e. the same altitude of 822 km but it has a different mean local solar time (LST). Ground track maintenance manoeuvres are performed to maintain the ground track within a predefined control band around the reference ground track and the band is ±40 km for THEOS spacecraft. This paper presents the first ground track maintenance manoeuvre of THEOS spacecraft and the detailed results. In addition, it also includes one and a half year of operation as seen by GISTDA operators. It finally describes the foreseenable activities for the next orbit control manoeuvre (OCM) preparation.
Abstract: TiO2/MgO composite films were prepared by coating
the magnesium acetate solution in the pores of mesoporous TiO2
films using a dip coating method. Concentrations of magnesium
acetate solution were varied in a range of 1x10-4 – 1x10-1 M. The
TiO2/MgO composite films were characterized by scanning electron
microscopy (SEM), transmission electron microscropy (TEM),
electrochemical impedance spectroscopy(EIS) , transient voltage
decay and I-V test. The TiO2 films and TiO2/MgO composite films
were immersed in a 0.3 mM N719 dye solution. The Dye-sensitized
solar cells with the TiO2/MgO/N719 structure showed an optimal
concentration of magnesium acetate solution of 1x10-3 M resulting in
the MgO film estimated thickness of 0.0963 nm and giving the
maximum efficiency of 4.85%. The improved efficiency of dyesensitized
solar cell was due to the magnesium oxide film as the wide
band gap coating decays the electron back transfer to the triiodide
electrolyte and reduce charge recombination.
Abstract: Perhaps no single issue has been cited as either the root
cause and / or the greatest challenge to the restructured power system then the lack of adequate reliable transmission. Probabilistic transmission planning has become increasingly necessary and important in recent
years. The transmission planning analysis carried out by the authors,
spans a 10-year horizon, taking into consideration a value of 2 % load
increase / year at each consumer. Taking into consideration this increased
load, a probabilistic power flow was carried out, all the system components
being regarded from probabilistic point of view. Several contingencies
have been generated, for assessing the security of the power system. The results have been analyzed and several important conclusions were pointed. The objective is to achieve a network that works without limit violations for all (or most of) scenario realizations. The case study is represented by the IEEE 14 buses test power system.
Abstract: The Bayesian Optimization Algorithm (BOA) is an algorithm based on the estimation of distributions. It uses techniques from modeling data by Bayesian networks to estimating the joint distribution of promising solutions. To obtain the structure of Bayesian network, different search algorithms can be used. The key point that BOA addresses is whether the constructed Bayesian network could generate new and useful solutions (strings), which could lead the algorithm in the right direction to solve the problem. Undoubtedly, this ability is a crucial factor of the efficiency of BOA. Varied search algorithms can be used in BOA, but their performances are different. For choosing better ones, certain suitable method to present their ability difference is needed. In this paper, a greedy search algorithm and a stochastic search algorithm are used in BOA to solve certain optimization problem. A method using Kullback-Leibler (KL) Divergence to reflect their difference is described.
Abstract: The objective of this research was to find the
relationship between auspicious meaning in eastern wisdom and the
interpretation as a guideline for the design and development of
community souvenirs. The sample group included 400 customers in
Bangkok who used to buy community souvenir products. The
information was applied to design the souvenirs which were
considered for the appropriateness by 5 design specialists. The data
were analyzed to find frequency, percentage, and SD with the results
as follows. 1) The best factor referring to the auspicious meaning is
color. The application of auspicious meaning can make the value
added to the product and bring the fortune to the receivers. 2) The
effectiveness of the auspicious meaning integration on the design of
community souvenir product was in high level. When considering in
each aspect, it was found that the interpretation aspect was in high
level, the congruency of the auspicious meaning and the utility of the
product was in high level. The attractiveness and the good design
were in very high level while the potential of the value added in the
product design was in high level. The suitable application to the
design of community souvenir product was in high level.
Abstract: Information theory and Statistics play an important role in Biological Sciences when we use information measures for the study of diversity and equitability. In this communication, we develop the link among the three disciplines and prove that sampling distributions can be used to develop new information measures. Our study will be an interdisciplinary and will find its applications in Biological systems.
Abstract: This paper describes a novel monitoring scheme to
minimize total active power in digital circuits depend on the demand
frequency, by adjusting automatically both supply voltage and
threshold voltages based on circuit operating conditions such as
temperature, process variations, and desirable frequency. The delay
monitoring results, will be control and apply so as to be maintained at
the minimum value at which the chip is able to operate for a given
clock frequency. Design details of power monitor are examined using
simulation framework in 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 40 μW for 32nm technology;
moreover the results show that our proposed circuit design is not far
sensitive to the temperature variations and also process variations.
Besides, uses the simple blocks which offer good sensitivity, high
speed, the continuously feedback loop. This design provides up to
40% reduction in power consumption in active mode.
Abstract: The scientific perspective, the practice area of physical education and sports activities improve power capacity in all its forms of expression, being a generator of the research topics. Today theories that strength training athletes and slow down development progress will affect the strength and flexibility are discredited. On the other hand there are sectors and / or samples whose results are sports of the way higher manifestation of power as a result of the composition of the force and velocity, being based in this respect on the systematic and continuous development of both bio-motric capacities said. Training of force for children was and is controversial. Teama de accidentări sau a stopării premature a procesului de creştere a făcut ca în trecut copiii să fie ţinuţi departe de lucrul cu diferite greutăţi.Fear of injury or premature stop the growth process in the past made the children to be kept away from working with different weights. Recent studies have shown that the risk of accidents is relatively small and the strength training can help prevent them. For example, most accidents occur at the level of athletics ligaments and tendons. From this point of view, it can be said that a progressive intervention of force training, optimal design, will help enhancing their process, such as athlete much better prepared to meet training requests and competitions. Preparation of force provides a solid basis for further phases in the highest performance.
Abstract: In this paper a systematic method via H∞ control
design is proposed to select a sensor set that satisfies a number
of input criteria for a MAGLEV suspension system. The proposed
method recovers a number of optimised controllers for each possible
sensor set that satisfies the performance and constraint criteria using
evolutionary algorithms.
Abstract: This paper shows that the economy of any country
can be presented as three different shells such as: economic shell of a
big, a medium and a small business. The new concepts were
introduced such as: volume of an economic shell, coefficient of
shell-s expansion (compression) etc. These shells can expansion or
compress under action by internal or external powers and when shell
expansions - it means the rising of a business activity and
compression shows us that economy goes on recession. This process
of an expansion or a compression can develop in the various ways
like linear, logarithm or any other mathematical laws.
Abstract: An effect of rolling temperature on the mechanical properties and microstructural evolution of an Al-Mg-Si alloy was studied. The material was rolled up to a true strain of ~0.7 at three different temperatures viz; room temperature, liquid propanol and liquid nitrogen. The liquid nitrogen rolled sample exhibited superior properties with a yield and tensile strength of 332 MPa and 364 MPa, respectively, with a reasonably good ductility of ~9%. The liquid nitrogen rolled sample showed around 54 MPa increase in tensile strength without much reduction in the ductility as compared to the as received T6 condition alloy. The microstructural details revealed equiaxed grains in the annealed and solutionized sample and elongated grains in the rolled samples. In addition, the cryorolled samples exhibited fine grain structure compared to the room temperature rolled samples.
Abstract: In this paper, mathematical modeling of detonation in the ground is studied. Estimation of flow parameters such as velocity, maximum velocity, acceleration, maximum acceleration, shock pressure as a result of an explosion in the ground have been computed in an appropriate dynamic model approach. The variation of these parameters with the diameter of detonation place (L), density of earth or stone (¤ü), time decay of detonation (T), peak pressure (Pm), and time (t) have been analyzed. The model has been developed from the concept of underwater explosions [Refs. [1]-[3]] with appropriate changes to the present model requirements.
Abstract: In this paper, gate leakage current has been mitigated
by the use of novel nanoscale MOSFET with Source/Drain-to-Gate
Non-overlapped and high-k spacer structure for the first time. A
compact analytical model has been developed to study the gate
leakage behaviour of proposed MOSFET structure. The result
obtained has found good agreement with the Sentaurus Simulation.
Fringing gate electric field through the dielectric spacer induces
inversion layer in the non-overlap region to act as extended S/D
region. It is found that optimal Source/Drain-to-Gate Non-overlapped
and high-k spacer structure has reduced the gate leakage current to
great extent as compared to those of an overlapped structure. Further,
the proposed structure had improved off current, subthreshold slope
and DIBL characteristic. It is concluded that this structure solves the
problem of high leakage current without introducing the extra series
resistance.
Abstract: Open urban public spaces comprise an important
element for the development of social, cultural and economic
activities of the population in the modern cities. These spaces are also
considered regulators of the region-s climate conditions, providing
better thermal, visual and auditory conditions which can be optimized
by the application of appropriate strategies of bioclimatic design. The
paper focuses on the analysis and evaluation of the recent unification
of the open spaces in the centre of Xanthi, a medium – size city in
northern Greece, from a bioclimatic perspective, as well as in the
creation of suitable methodology. It is based both on qualitative
observation of the interventions by fieldwork research and
assessment and on quantitative analysis and modeling of the research
area.
Abstract: The Expert Witness Testimony in the Battered
Woman Syndrome Expert witness testimony (EWT) is a kind of
information given by an expert specialized in the field (here in BWS)
to the jury in order to help the court better understand the case. EWT
does not always work in favor of the battered women. Two main
decision-making models are discussed in the paper: the Mathematical
model and the Explanation model. In the first model, the jurors
calculate ″the importance and strength of each piece of evidence″
whereas in the second model they try to integrate the EWT with the
evidence and create a coherent story that would describe the crime.
The jury often misunderstands and misjudges battered women for
their action (or in this case inaction). They assume that these women
are masochists and accept being mistreated for if a man abuses a
woman constantly, she should and could divorce him or simply leave
at any time. The research in the domain found that indeed, expert
witness testimony has a powerful influence on juror’s decisions thus
its quality needs to be further explored. One of the important factors
that need further studies is a bias called the dispositionist worldview
(a belief that what happens to people is of their own doing). This
kind of attributional bias represents a tendency to think that a
person’s behavior is due to his or her disposition, even when the
behavior is clearly attributed to the situation. Hypothesis The
hypothesis of this paper is that if a juror has a dispositionist
worldview then he or she will blame the rape victim for triggering the
assault. The juror would therefore commit the fundamental
attribution error and believe that the victim’s disposition caused the
rape and not the situation she was in. Methods The subjects in the
study were 500 randomly sampled undergraduate students from
McGill, Concordia, Université de Montréal and UQAM.
Dispositional Worldview was scored on the Dispositionist
Worldview Questionnaire. After reading the Rape Scenarios, each
student was asked to play the role of a juror and answer a
questionnaire consisting of 7 questions about the responsibility,
causality and fault of the victim. Results The results confirm the
hypothesis which states that if a juror has a dispositionist worldview
then he or she will blame the rape victim for triggering the assault.
By doing so, the juror commits the fundamental attribution error
because he will believe that the victim’s disposition, and not the
constraints or opportunities of the situation, caused the rape scenario.
Abstract: This paper presents an application of power line
carrier (PLC) for electrical power telemetering. This system has a
special capability of transmitting the measured values to a centralized
computer via power lines. The PLC modem as a passive high-pass
filter is designed for transmitting and receiving information. Its
function is to send the information carrier together with transmitted
data by superimposing it on the 50 Hz power frequency signal. A
microcontroller is employed to function as the main processing of the
modem. It is programmed for PLC control and interfacing with other
devices. Each power meter, connected via a PLC modem, is assigned
with a unique identification number (address) for distinguishing each
device from one another.