Abstract: The global solved problem is the calculation of the
parameters of ceramic material from a set of destruction tests of
ceramic heads of total hip joint endoprosthesis. The standard way of
calculation of the material parameters consists in carrying out a set of
3 or 4 point bending tests of specimens cut out from parts of the
ceramic material to be analysed. In case of ceramic heads, it is not
possible to cut out specimens of required dimensions because the
heads are too small (if the cut out specimens were smaller than the
normalised ones, the material parameters derived from them would
exhibit higher strength values than those which the given ceramic
material really has). A special destruction device for heads
destruction was designed and the solved local problem is the
modification of this destructive device based on the analysis of
tensile stress in the head for two different values of the depth of the
conical hole in the head. The goal of device modification is a shift of
the location with extreme value of σ1max from the region of head’s
hole bottom to its opening. This modification will increase the
credibility of the obtained material properties of bioceramics, which
will be determined from a set of head destructions using the Weibull
weakest link theory.
Abstract: A noble low NOx combustion technology, based on
partial oxidation combustion concept in a fuel rich combustion zone, is
successfully applied in this research. The burner is designed such that
a portion of fuel is heated and pre-vaporized in the furnace then
injected into a fuel rich combustion zone so that a partial oxidation
reaction occurs. The effects of equivalence ratio, thermal load, and
fuel distribution ratio on the emissions of NOx and CO are
experimentally investigated. This newly developed combustion
technology showed very low NOx emission level, about 12 ppm, when
light oil is used as a fuel.
Abstract: Folic acid (FA) is known to be an important
supplement to prevent neural tube defect (NTD) in pregnant women.
Similar to some commercial formulations, sodium bicarbonate
solution is used as a solvent for FA. This work uses the antisolvent
vapour precipitation (AVP), incorporating ethanol vapour as the
convective drying medium in place of air to produce branch-like
micro-structure FA particles. Interestingly, the dissolution rate of the
resultant particle is 2-3 times better than the particle produce from
conventional air drying due to the higher surface area of particles
produced. The higher dissolution rate could possibly improve the
delivery and absorption of FA in human body. This application could
potentially be extended to other commercial products, particularly in
less soluble drugs to improve its solubility.
Abstract: This paper presents a real-time visualization technique
and filtering of classified LiDAR point clouds. The visualization is
capable of displaying filtered information organized in layers by the
classification attribute saved within LiDAR datasets. We explain the
used data structure and data management, which enables real-time
presentation of layered LiDAR data. Real-time visualization is
achieved with LOD optimization based on the distance from the
observer without loss of quality. The filtering process is done in two
steps and is entirely executed on the GPU and implemented using
programmable shaders.
Abstract: The North-eastern part of India, which receives
heavier rainfall than other parts of the subcontinent, is of great
concern now-a-days with regard to climate change. High intensity
rainfall for short duration and longer dry spell, occurring due to
impact of climate change, affects river morphology too. In the present
study, an attempt is made to delineate the North-eastern region of
India into some homogeneous clusters based on the Fuzzy Clustering
concept and to compare the resulting clusters obtained by using
conventional methods and nonconventional methods of clustering.
The concept of clustering is adapted in view of the fact that, impact
of climate change can be studied in a homogeneous region without
much variation, which can be helpful in studies related to water
resources planning and management. 10 IMD (Indian Meteorological
Department) stations, situated in various regions of the North-east,
have been selected for making the clusters. The results of the Fuzzy
C-Means (FCM) analysis show different clustering patterns for
different conditions. From the analysis and comparison it can be
concluded that nonconventional method of using GCM data is
somehow giving better results than the others. However, further
analysis can be done by taking daily data instead of monthly means to
reduce the effect of standardization.
Abstract: Metallic foams have good potential for lightweight
structures for impact and blast mitigation. Therefore it is important to
find out the optimized foam structure (i.e. cell size, shape, relative
density, and distribution) to maximise energy absorption. In this
paper, quasistatic compression and microstructural characterization
of closed-cell aluminium foams of different pore size and cell
distributions have been carried out. We present results for two
different aluminium metal foams of density 0.49-0.51 g/cc and 0.31-
0.34 g/cc respectively that have been tested in quasi-static
compression. The influence of cell geometry and cell topology on
quasistatic compression behaviour has been investigated using optical
microscope and computed tomography (micro-CT) analysis. It is
shown that the deformation is not uniform in the structure and
collapse begins at the weakest point.
Abstract: In this paper, the effect of WC-12Co particle
temperature in HVOF thermal spraying process on the coating
thickness has been studied. The statistical results show that the spray
distance and oxygen-to-fuel ratio are effective factors on particle
characterization and thickness of HVOF thermal spraying coatings.
Spray Watch diagnostic system, scanning electron microscopy
(SEM), X-ray diffraction and thickness measuring system were used
for this purpose.
Abstract: Medical imaging technology has experienced a
dramatic change in the last few years. Medical imaging refers to the
techniques and processes used to create images of the human body
(or parts thereof) for various clinical purposes such as medical
procedures and diagnosis or medical science including the study of
normal anatomy and function. With the growth of computers and
image technology, medical imaging has greatly influenced the
medical field. The diagnosis of a health problem is now highly
dependent on the quality and the credibility of the image analysis.
This paper deals with the various aspects and types of medical
imaging.
Abstract: The purpose of the present work is to review some
data for the management challenges that the aquaculture industry in
Greece is currently facing. The results indicate that Greek
aquaculture fish farms apply Human Resources Management (HRM)
practices which can increase motivation, commitment and job
satisfaction of their personnel. In turn, these practices can increase
the productivity of the business. The Greek fish farms appear to
invest in research and technological innovation with a good record in
research activities and the generation of patents. Interestingly, the
results of the present work were carried out during the period of the
recent economic crisis in Greece. Several sectors of the Greek
economy were severely affected by the financial problems of the
Greek government and the Greek banks. Under the adverse
economical conditions created by the Greek economic crisis, even the
Greek aquaculture industry, which historically is considered as a
thriving national exporting business sector, experienced harsh
economic and market conditions. As a result of the global, European
and national economic crisis, consumption of fish dropped while
companies had to hold most of their stocked fish in order to regulated
the flow to the market and the price. This occurred at a time where
Banks in Greece had their own financial crisis – banking crisis -
which resulted in limited access to lending for the all business sectors
of the national economy including the Greek aquaculture industry. In
spite of these economic conditions, the Greek aquaculture industry,
after a series of mergers and acquisitions, has now stabilized
production and exhibits very good prospects for future growth.
Evidently, the firms had to cut salaries and on some occasions even
pay their staff in arrears. Nevertheless, the results presented in this
paper indicate that during the economic crisis, the surveyed fish
farms maintained their HRM practices, investing in their human
capital and technological input. In fact, human capital and
technological input are the ticket for future success of companies in
any business sector.
Abstract: A novel simulation method to determine the
displacements of machine tools due to thermal factors is presented.
The specific characteristic of this method is the employment of
original CAD data from the design process chain, which is
interpreted by an algorithm in terms of geometry-based allocation of
convection and radiation parameters. Furthermore analogous models
relating to the thermal behaviour of machine elements are
automatically implemented, which were gained by extensive
experimental testing with thermography imaging. With this a
transient simulation of the thermal field and in series of the
displacement of the machine tool is possible simultaneously during
the design phase. This method was implemented and is already used
industrially in the design of machining centres in order to improve
the quality of herewith manufactured workpieces.
Abstract: This paper presents a comparison between using a
desktop web application and a mobile application for students
enrolling in courses at Rangsit University, Thailand. In addition,
Rangsit University has enhanced the enrollment process by
leveraging its information systems, which allows students to choose
to enroll in courses online. In order to use the system, students must
provide their identification and personal documents for registration.
The reason to have a mobile application is to support students’ ability
to access the system at anytime, anywhere and anyplace. The
objective of this paper was to: 1. Evaluate the success of developing a
user friendly mobile device system and 2. Measure user interest in
future mobile development.
Abstract: The article discusses multimodal mobility in
contemporary societies as a main planning and organization issue in
the functioning of administrative bodies, a problem which really
exists in the space of contemporary cities in terms of shaping modern
transport systems. The article presents classification of available
resources and initiatives undertaken for developing multimodal
mobility. Solutions can be divided into three groups of measures –
physical measures in the form of changes of the transport network
infrastructure, organizational ones (including transport policy) and
information measures. The latter ones include in particular direct
support for people travelling in the transport network by providing
information about ways of using available means of transport. A
special measure contributing to this end is a trip planner. The article
compares several selected planners. It includes a short description of
the Green Travelling Project, which aims at developing a planner
supporting environmentally friendly solutions in terms of transport
network operation. The article summarizes preliminary findings of
the project.
Abstract: reliability-based methodology for the assessment
and evaluation of reinforced concrete (R/C) structural elements of
concrete structures is presented herein. The results of the reliability
analysis and assessment for R/C structural elements were verified by
the results obtained through deterministic methods. The outcomes of
the reliability-based analysis were compared against currently
adopted safety limits that are incorporated in the reliability indices
β’s, according to international standards and codes. The methodology
is based on probabilistic analysis using reliability concepts and
statistics of the main random variables that are relevant to the subject
matter, and for which they are to be used in the performance-function
equation(s) associated with the structural elements under study.
These methodology techniques can result in reliability index β, which
is commonly known as the reliability index or reliability measure
value that can be utilized to assess and evaluate the safety, human
risk, and functionality of the structural component. Also, these
methods can result in revised partial safety factor values for certain
target reliability indices that can be used for the purpose of
redesigning the R/C elements of the building and in which they could
assist in considering some other remedial actions to improve the
safety and functionality of the member.
Abstract: In this paper, design of solid-state battery/supercapacitor emulator based on dc-dc boost converter is described.
The emulator mimics charging behavior of any storage device based
on a predefined behavior set by the user. The device is operated by a
two-level control structure: high-level emulating controller and low-
level input voltage controller. Simulation and experimental results are
shown to demonstrate the emulator operation.
Abstract: Innovations not only contribute to competitiveness of
the company but have also positive effects on revenues. On average,
product innovations account to 14 percent of companies’ sales.
Innovation management has substantially changed during the last
decade, because of growing reliance on external partners. As a
consequence, a new task for purchasing arises, as firms need to
understand which suppliers actually do have high potential
contributing to the innovativeness of the firm and which do not.
Proper organization of the purchasing function is important since
for the majority of manufacturing companies deal with substantial
material costs which pass through the purchasing function. In the past
the purchasing function was largely seen as a transaction-oriented,
clerical function but today purchasing is the intermediate with supply
chain partners contributing to innovations, be it product or process
innovations. Therefore, purchasing function has to be organized
differently to enable firm innovation potential.
However, innovations are inherently risky. There are behavioral
risk (that some partner will take advantage of the other party),
technological risk in terms of complexity of products and processes
of manufacturing and incoming materials and finally market risks,
which in fact judge the value of the innovation. These risks are
investigated in this work. Specifically, technological risks which deal
with complexity of the products, and processes will be investigated
more thoroughly. Buying components or such high edge technologies
necessities careful investigation of technical features and therefore is
usually conducted by a team of experts. Therefore it is hypothesized
that higher the technological risk, higher will be the centralization of
the purchasing function as an interface with other supply chain
members.
Main contribution of this research lies is in the fact that analysis
was performed on a large data set of 1493 companies, from 25
countries collected in the GMRG 4 survey. Most analyses of
purchasing function are done by case study analysis of innovative
firms. Therefore this study contributes with empirical evaluations that
can be generalized.
Abstract: The goal of this article is the analysis of knowledge
transfer at the regional level of the Czech Republic. We show how
goals of enterprises´ innovative activities are related to the rate of
cooperation with different actors within regional innovative systems
as well as in other world regions. The results show that the most
important partners of enterprises are their suppliers and clients in
most Czech regions. The cooperation rate of enterprises correlates
significantly mainly with enterprises´ efforts to enter new markets
and reduce labour costs per unit output. The meaning of this
cooperation decreases with the increase of partner’s distance.
Regarding the type of a cooperating partner, cooperation within an
enterprise had to do with the increase of market share and decrease of
labour costs. On the other hand, cooperation with clients had to do
with efforts to replace outdated products or processes or enter new
markets. We can pay less attention to the cooperation with
government authorities and organizations. The reasons for
marginalization of this cooperation should be submitted to further
detailed investigation.
Abstract: Urban greenery remains the bastion of urban
landscape and a key to sustainable development due to its integral
connections to the general health and wellbeing of urban residents.
However, in an era of rapid urbanisation, recent studies indicate that
urban greenery, especially ecologically sensitive areas, in many
African cities is becoming increasingly depleted. Given the scale and
rate of natural and anthropogenic change, effective management of
urban greenery as the ultimate goal of restoring depleting urban
landscapes is urgent. This review advocates for an urban resilience
model to managing urban greenery.
Abstract: The theoretical approach is developed to describe the
change of drops in the atmosphere of own steam and buffer gas under
irradiation. It is shown that the irradiation influences on size of stable
droplet and on the conditions under which the droplet exists. Under
irradiation the change of drop becomes more complex: the not
monotone and periodical change of size of drop becomes possible.
All possible solutions are represented by means of phase portrait. It is
found all qualitatively different phase portraits as function of critical
parameters: rate generation of clusters and substance density.
Abstract: The systematic evaluation of manufacturing
technologies with regard to the potential for product designing
constitutes a major challenge. Until now, conventional evaluation
methods primarily consider the costs of manufacturing technologies.
Thus, the potential of manufacturing technologies for achieving
additional product design features is not completely captured. To
compensate this deficit, final evaluations of new technologies are
mainly intuitive in practice. Therefore, an additional evaluation
dimension is needed which takes the potential of manufacturing
technologies for specific realizable product designs into account. In
this paper, we present the approach of an evaluation method for
selecting manufacturing technologies with regard to their potential
for product designing. This research is done within the Fraunhofer
innovation cluster »AdaM« (Adaptive Manufacturing) which targets
the development of resource efficient and adaptive manufacturing
technology processes for complex turbomachinery components.
Abstract: The use of IT equipment has become a part of every
day. However, each device that is part of cyberspace should be
secured against unauthorized use. It is very important to know the
basics of these security devices, but also the basics of safe conduct
their owners. This information should be part of every curriculum
computer science education in primary and secondary schools.
Therefore, the work focuses on the education of pupils in primary and
secondary schools on the Internet. Analysis of the current state
describes approaches to the education of pupils in security issues on
the Internet. The paper presents a questionnaire-based survey which
was carried out in the Czech Republic, whose task was to ascertain
the level of opinion pupils in primary and secondary schools on the
issue of communication in social networks. The research showed that
awareness of socio-pathological phenomena on the Internet
environment is very low. Based on the results it was proposed
appropriate ways of teaching to this issue and its inclusion a proposal
of curriculum for primary and secondary schools.