Abstract: Paper presents a study about dynamic effects obtained
from the dynamic load testing of the city highway bridges in Latvia
carried out from 2005 to 2012. 9 prestressed concrete bridges and 4
composite bridges were considered. 11 of 13 bridges were designed
according to the Eurocodes but two according to the previous
structural codes used in Latvia (SNIP 2.05.03-84). The dynamic
properties of the bridges were obtained by heavy vehicle passing the
bridge roadway with different driving speeds and with or without
even pavement. The obtained values of the Dynamic amplification
factor (DAF) and the bridge natural frequency were analyzed and
compared to the values of built-in traffic load models provided in
Eurocode 1. The actual DAF values for even bridge pavement in the
most cases are smaller than the value adopted in Eurocode 1. Vehicle
speed for uneven pavements significantly influence Dynamic
amplification factor values.
Abstract: In this paper, we propose a new packing strategy to
find a free resource for run-time mapping of application tasks to
NoC-based Heterogeneous MPSoC. The proposed strategy minimizes
the task mapping time in addition to placing the communicating tasks
close to each other. To evaluate our approach, a comparative study is
carried out for a platform containing single task supported PEs.
Experiments show that our strategy provides better results when
compared to latest dynamic mapping strategies reported in the
literature.
Abstract: A computational fluid dynamics simulation is done for
non-Newtonian fluid in a baffled stirred tank. The CMC solution is
taken as non-Newtonian shear thinning fluid for simulation. The
Reynolds Average Navier Stocks equation with steady state multi
reference frame approach is used to simulate flow in the stirred tank.
The turbulent flow field is modelled using realizable k-ε turbulence
model. The simulated velocity profiles of Rushton turbine is
validated with literature data. Then, the simulated flow field of CD-6
impeller is compared with the Rushton turbine. The flow field
generated by CD-6 impeller is less in magnitude than the Rushton
turbine. The impeller global parameter, power number and flow
number, and entropy generation due to viscous dissipation rate is also
reported.
Abstract: This paper presents a study on Proportional Resonant
(PR) current control with additional PR harmonic compensators for
Grid Connected Photovoltaic (PV) Inverters. Both simulation and
experimental results will be presented. Testing was carried out on a
3kW Grid-Connected PV Inverter which was designed and
constructed for this research.
Abstract: The use of information and communication
technologies such as computers, mobile phones and the Internet is
becoming prevalent in today’s world; and it is facilitating access to a
vast amount of data, services and applications for the improvement of
people’s lives. However, this prevalence of ICTs is hampered by the
problem of low income levels in developing countries to the point
where people cannot timeously replace or repair their ICT devices
when damaged or lost; and this problem serves as a motivation for
this study whose aim is to examine the perceptions of teachers on the
reliability of cellphones when used for teaching and learning
purposes. The research objectives unfolding this aim are of two
types: Objectives on the selection and design of theories and models,
and objectives on the empirical testing of these theories and models.
The first type of objectives is achieved using content analysis in an
extensive literature survey: and the second type of objectives is
achieved through a survey of high school teachers from the ILembe
and UMgungundlovu districts in the KwaZulu-Natal province of
South Africa. Data collected from this questionnaire based survey is
analysed in SPSS using descriptive statistics and Pearson correlations
after checking the reliability and validity of the questionnaires. The
main hypothesis driving this study is that there is a relationship
between the demographics and the attribution identity of teachers on
one hand, and their perceptions on the reliability of cellphones on the
other hand, as suggested by existing literature; except that attribution
identities are considered in this study under three angles: intention,
knowledge and ability, and action. The results of this study confirm
that the perceptions of teachers on the reliability of cellphones for
teaching and learning are affected by the school location of these
teachers, and by their perceptions on learners’ cellphones usage
intentions and actual use.
Abstract: An investigation into the effect of countersunk depth,
plate thickness, countersunk angle and plate width on the stress
concentration around countersunk hole is carried out with the help of
finite element analysis. The variation of stress concentration with
respect to these parameters is studied for three types of loading viz.
uniformly distributed load, uniformly varying load and functionally
distributed load. The results of the finite element analysis are
interpreted and some conclusions are drawn. The distribution of
stress concentration around countersunk hole in isotropic plates
simply supported at all the edges is found similar and is independent
of loading. The maximum stress concentration also occurs at a
particular point irrespective of the loading conditions.
Abstract: Present study is aimed on the cutting process of circular
cross-section rods where the fracture is used to separate one rod
into two pieces. Incorporating the phenomenological ductile fracture
model into the explicit formulation of finite element method, the
process can be analyzed without the necessity of realizing too many
real experiments which could be expensive in case of repetitive
testing in different conditions. In the present paper, the steel AISI
1045 was examined and the tensile tests of smooth and notched
cylindrical bars were conducted together with biaxial testing of the
notched tube specimens to calibrate material constants of selected
phenomenological ductile fracture models. These were implemented
into the Abaqus/Explicit through user subroutine VUMAT and used
for cutting process simulation. As the calibration process is based
on variables which cannot be obtained directly from experiments,
numerical simulations of fracture tests are inevitable part of the
calibration. Finally, experiments regarding the cutting process were
carried out and predictive capability of selected fracture models is
discussed. Concluding remarks then make the summary of gained
experience both with the calibration and application of particular
ductile fracture criteria.
Abstract: The postharvest quality management of tomatoes is
important to limit the amount of losses that occur due to deterioration
between harvest and consumption. This study was undertaken to
investigate the effects of pre- and postharvest integrated agrotechnologies,
involving greenhouse microclimate and postharvest
storage conditions, on the postharvest quality attributes of four
tomato cultivars. Tomato fruit firmness, colour (hue angle (h°) and
L* value), pH and total soluble solids for the cultivars Bona,
Star 9037, Star 9009 and Zeal, grown in a fan-pad evaporativelycooled
and an open-ended naturally-ventilated tunnel, were harvested
at the mature-green stage. The tomatoes were stored for 28 days
under cold storage conditions, with a temperature of 13°C and RH of
85%, and under ambient air conditions, with a temperature of 23±
2°C and RH of 52± 4%. This study has provided information on the
effect of integrated pre-harvest and postharvest agro-technologies,
involving greenhouse microclimate and postharvest storage
environment on the postharvest quality attributes of four of the
tomato cultivars in South Africa. NVT-grown tomatoes retained
better textural qualities, but ripened faster by changing from green to
red faster, although these were reduced under cold storage conditions.
FPVT-grown tomatoes had lower firmness, but ripened slowly with
higher colour attributes. With cold storage conditions, the firmness of
FPVT-grown tomatoes was maintained. Cultivar Bona firmness and
colour qualities depreciated the fastest, but it had higher TSS content
and lower pH values. Star 9009 and Star 9037 presented better
quality, by retaining higher firmness and ripening slowly, but they
had the lowest TSS contents and high pH values, especially
Star 9037. Cold storage improved the firmness of tomato cultivars
with poor textural quality and faster colour changes.
Abstract: In this paper, we introduce a generalized Chebyshev
collocation method (GCCM) based on the generalized Chebyshev
polynomials for solving stiff systems. For employing a technique
of the embedded Runge-Kutta method used in explicit schemes, the
property of the generalized Chebyshev polynomials is used, in which
the nodes for the higher degree polynomial are overlapped with those
for the lower degree polynomial. The constructed algorithm controls
both the error and the time step size simultaneously and further
the errors at each integration step are embedded in the algorithm
itself, which provides the efficiency of the computational cost. For
the assessment of the effectiveness, numerical results obtained by the
proposed method and the Radau IIA are presented and compared.
Abstract: In today’s world, the LED display has been used for
presenting visual information under various circumstances. Such
information is an important intermediary in the human information
processing. Researchers have been investigated diverse factors that
influence this process effectiveness. The letter size is undoubtedly
one major factor that has been tested and recommended by many
standards and guidelines. However, viewing information on the
display from direct perpendicular position is a typical assumption
whereas many actual events are required viewing from the angles.
This current research aims to study the effect of oblique viewing
angle and viewing distance on ability to recognize alphabet, number,
and English word. The total of ten participants was volunteered to our
3 x 4 x 4 within subject study. Independent variables include three
distance levels (2, 6, and 12 m), four oblique angles (0, 45, 60, 75
degree), and four target types (alphabet, number, short word, and
long word). Following the method of constant stimuli our study
suggests that the larger oblique angle, ranging from 0 to 75 degree
from the line of sight, results in significant higher legibility threshold
or larger font size required (p-value < 0.05). Viewing distance factor
also shows to have significant effect on the threshold (p-value
Abstract: The substantial similarity of fatigue mechanism in a
new test rig for rolling contact fatigue (RCF) has been investigated. A
new reduced-scale test rig is designed to perform controlled RCF
tests in wheel-rail materials. The fatigue mechanism of the rig is
evaluated in this study using a combined finite element-fatigue
prediction approach. The influences of loading conditions on fatigue
crack initiation have been studied. Furthermore, the effects of some
artificial defects (squat-shape) on fatigue lives are examined. To
simulate the vehicle-track interaction by means of the test rig, a threedimensional
finite element (FE) model is built up. The nonlinear
material behaviour of the rail steel is modelled in the contact
interface. The results of FE simulations are combined with the critical
plane concept to determine the material points with the greatest
possibility of fatigue failure. Based on the stress-strain responses, by
employing of previously postulated criteria for fatigue crack initiation
(plastic shakedown and ratchetting), fatigue life analysis is carried
out. The results are reported for various loading conditions and
different defect sizes. Afterward, the cyclic mechanism of the test rig
is evaluated from the operational viewpoint. The results of fatigue
life predictions are compared with the expected number of cycles of
the test rig by its cyclic nature. Finally, the estimative duration of the
experiments until fatigue crack initiation is roughly determined.
Abstract: Thanks to informational technologies development
every sphere of economics is becoming more and more datacentralized
as people are generating huge datasets containing
information on any aspect of their life. Applying research of such
data to human resources management allows getting scarce statistics
on labor market state including salary expectations and potential
employees’ typical career behavior, and this information can become
a reliable basis for management decisions.
The following article presents results of career behavior research
based on freely accessible resume data. Information used for study is
much wider than one usually uses in human resources surveys. That
is why there is enough data for statistically significant results even
for subgroups analysis.
Abstract: One of the most important tasks in the risk
management is the correct determination of probability of default
(PD) of particular financial subjects. In this paper a possibility of
determination of financial institution’s PD according to the creditscoring
models is discussed. The paper is divided into the two parts.
The first part is devoted to the estimation of the three different
models (based on the linear discriminant analysis, logit regression
and probit regression) from the sample of almost three hundred US
commercial banks. Afterwards these models are compared and
verified on the control sample with the view to choose the best one.
The second part of the paper is aimed at the application of the chosen
model on the portfolio of three key Czech banks to estimate their
present financial stability. However, it is not less important to be able
to estimate the evolution of PD in the future. For this reason, the
second task in this paper is to estimate the probability distribution of
the future PD for the Czech banks. So, there are sampled randomly
the values of particular indicators and estimated the PDs’ distribution,
while it’s assumed that the indicators are distributed according to the
multidimensional subordinated Lévy model (Variance Gamma model
and Normal Inverse Gaussian model, particularly). Although the
obtained results show that all banks are relatively healthy, there is
still high chance that “a financial crisis” will occur, at least in terms
of probability. This is indicated by estimation of the various quantiles
in the estimated distributions. Finally, it should be noted that the
applicability of the estimated model (with respect to the used data) is
limited to the recessionary phase of the financial market.
Abstract: In the second decade of the XXI century the role of
tourism destination attractiveness is becoming increasingly important
for destination management. Competition in tourism market moves
from ordinary service quality to provision of unforgettable emotional
experience for tourists. The main purpose of the present study is to
identify the perception of the tourism destinations based on the
number of factors related to its tourist attractiveness.
The content analysis method was used to analyze the on-line
tourist feedback data immensely available in Social Media and in
travel related sites. The collected data made it possible to procure the
information which is necessary to understand the perceived
attractiveness of the destinations and key destination appeal factors
that are important for Russian leisure travelers.
Results of the present study demonstrate key attractiveness factors
or destination ‘properties’ that were unveiled as the most important
for Russian leisure tourists. The study targeted five main Spanish
tourism destinations that initially were determined by in-depth
interview with a number of Russian nationals who had visited Spain
at least once.
The research results can be useful for Spanish Tourism
Organization Representation office in Russia as well as for the other
national tourism organizations in order to promote their respective
destinations for Russian travelers focusing on main attractiveness
factors identified in this study.
Abstract: Aluminium and its alloys have excellent corrosion
resistant properties, ease of fabrication and high specific strength to
weight ratio. In this investigation an attempt has been made to study
the effect of different post weld heat treatment methods on the
mechanical and metallurgical properties of TIG welded joints of the
commercial aluminium alloy. Three different methods of post weld
heat treatments are solution heat treatment, artificial ageing and
combination of solution heat treatment and artificial aging are given
to TIG welded aluminium joints. Mechanical and metallurgical
properties of As welded joints of the aluminium alloys and post weld
heat treated joints of the aluminium alloys were examined.
Abstract: Esterification of p-bromo-m-cresol led to formation of
2-(4-bromo-3-methylphenoxy)acetate (1). 2-(4-Bromo-3-methyl
phenoxy)acetohydrazide (2) is derived from Compound (1) by
hydrazination. Compound (2) was reacted with different aromatic
aldehydes to yield N-(substituted benzylidiene)-2-(4-bromo-3-methyl
phenoxy)acetamide(3a-c). Cyclization of compound (3a-c) with
thioglycolic acid yielded 2-(4-bromo-3-methylphenoxy)-N-(4-oxo-2-
arylthiazolidin-3-yl) acetamide (4a-c). The newly synthesized
compounds were characterized on the basis of spectral studies and
evaluated for antibacterial and antifungal activities.
Abstract: Molluca Collision Zone is located at the junction of
the Eurasian, Australian, Pacific and the Philippines plates. Between
the Sangihe arc, west of the collision zone, and to the east of
Halmahera arc is active collision and convex toward the Molluca Sea.
This research will analyze the behavior of earthquake occurrence in
Molluca Collision Zone related to the distributions of an earthquake
in each partition regions, determining the type of distribution of a
occurrence earthquake of partition regions, and the mean occurence
of earthquakes each partition regions, and the correlation between the
partitions region. We calculate number of earthquakes using partition
method and its behavioral using conventional statistical methods. In
this research, we used data of shallow earthquakes type and its
magnitudes ≥4 SR (period 1964-2013). From the results, we can
classify partitioned regions based on the correlation into two classes:
strong and very strong. This classification can be used for early
warning system in disaster management.
Abstract: Kigelia africana (Lam.) Benth. (Bignoniaceae) is a
reputed traditional remedy for various human ailments such as skin
diseases, microbial infections, melanoma, stomach troubles,
metabolic disorders, malaria and general pains. In spite of the fruit
being widely used for purposes related to its antibacterial and
antifungal properties, the chemical constituents associated with the
activity have not been fully identified. To elucidate the active
principles, we evaluated the antimicrobial activity of fruit extracts
and purified fractions against Staphylococcus aureus, Enterococcus
faecalis, Moraxella catarrhalis, Escherichia coli, Candida albicans
and Candida tropicalis. Shade-dried fruits were powdered and
extracted with hydroalcoholic (1:1) mixture by soaking at room
temperature for 72 h. The crude extract was further fractionated by
column chromatography, with successive elution using hexane,
dichloromethane, ethyl acetate, acetone and methanol. The
dichloromethane and ethyl acetate fractions were combined and
subjected to column chromatography to furnish a wax and oil from
the eluates of 20% and 40% ethyl acetate in hexane, respectively. The
GC-MS and GC×GC-MS results revealed that linoleic acid, linolenic
acid, palmitic acid, arachidic acid and stearic acid were the major
constituents in both oil and wax. The crude hydroalcoholic extract
exhibited the strongest activity with MICs of 0.125-0.5 mg/mL,
followed by the ethyl acetate (MICs = 0.125-1.0 mg/mL),
dichloromethane (MICs = 0.250-2.0 mg/mL), hexane (MICs = 0.25-
2.0 mg/mL), acetone (MICs = 0.5-2.0 mg/mL) and methanol (MICs =
1.0-2.0 mg/mL), whereas the wax (MICs = 2.0-4.0 mg/mL) and oil
(MICs = 4.0-8.0 mg/mL) showed poor activity. The study concludes
that synergistic interactions of chemical constituents could be
responsible for the antimicrobial activity of K. africana fruits, which
needs a more holistic approach to understand the mechanism of its
antimicrobial activity.
Abstract: Apps are today the most important possibility to adapt
mobile phones and computers to fulfill the special needs of their
users. Location- and context-sensitive programs are hereby the key to
support the interaction of the user with his/her environment and also
to avoid an overload with a plenty of dispensable information. The
contribution shows, how a trusted, secure and really bi-directional
communication and interaction among users and their environment
can be established and used, e.g. in the field of home automation.
Abstract: Nations are still finding it quite difficult to win mega
sport competitions despite the major contribution of sport to society
in terms of social and economic development, personal health, and in
education. Even though the world of sports has been transformed into
a huge global economy, it is important to note that the first step of
sport is usually its introduction to children at school through physical
education or PE. In other words, nations who do not win mega sport
competitions also suffer from a weak and neglected PE system. This
problem of the neglect of PE systems is the main motivation of this
research aimed at examining the factors affecting the perceived
awareness of physical education teachers on the ICTs that are
adoptable for the teaching and learning of physical education. Two
types of research objectives will materialize this aim: relevant
theories will be identified in relation to the analysis of the perceived
ICT awareness of PE teachers and subsequent models will be
compiled and designed from existing literature; the empirical testing
of such theories and models will also be achieved through the survey
of PE teachers from the Camperdown magisterial district of the
KwaZulu-Natal province of South Africa. The main hypothesis at the
heart of this study is the relationship between the demographics of PE
teachers, their behavior both as individuals and as social entities, and
their perceived awareness of the ICTs that are adoptable for PE, as
postulated by existing literature; except that this study categorizes
human behavior under performance expectancy, computer attitude,
and social influence. This hypothesis was partially confirmed by the
survey conducted by this research in the sense that performance
expectancy and teachers’ age, gender, computer usage, and class size
were found to be the only factors affecting their awareness of ICTs
for physical education.