Abstract: A laboratory study on the influence of compactive
effort on expansive black cotton specimens treated with up to 8%
ordinary Portland cement (OPC) admixed with up to 8% bagasse ash
(BA) by dry weight of soil and compacted using the energies of the
standard Proctor (SP), West African Standard (WAS) or
“intermediate” and modified Proctor (MP) were undertaken. The
expansive black cotton soil was classified as A-7-6 (16) or CL using
the American Association of Highway and Transportation Officials
(AASHTO) and Unified Soil Classification System (USCS),
respectively. The 7day unconfined compressive strength (UCS)
values of the natural soil for SP, WAS and MP compactive efforts are
286, 401 and 515kN/m2 respectively, while peak values of 1019,
1328 and 1420kN/m2 recorded at 8% OPC/ 6% BA, 8% OPC/ 2% BA
and 6% OPC/ 4% BA treatments, respectively were less than the
UCS value of 1710kN/m2 conventionally used as criterion for
adequate cement stabilization. The soaked California bearing ratio
(CBR) values of the OPC/BA stabilized soil increased with higher
energy level from 2, 4 and 10% for the natural soil to Peak values of
55, 18 and 8% were recorded at 8% OPC/4% BA 8% OPC/2% BA
and 8% OPC/4% BA, treatments when SP, WAS and MP compactive
effort were used, respectively. The durability of specimens was
determined by immersion in water. Soils treatment at 8% OPC/ 4%
BA blend gave a value of 50% resistance to loss in strength value
which is acceptable because of the harsh test condition of 7 days
soaking period specimens were subjected instead of the 4 days
soaking period that specified a minimum resistance to loss in strength
of 80%. Finally An optimal blend of is 8% OPC/ 4% BA is
recommended for treatment of expansive black cotton soil for use as
a sub-base material.
Abstract: A low bit rate still image compression scheme by
compressing the indices of Vector Quantization (VQ) and generating
residual codebook is proposed. The indices of VQ are compressed by
exploiting correlation among image blocks, which reduces the bit per
index. A residual codebook similar to VQ codebook is generated that
represents the distortion produced in VQ. Using this residual
codebook the distortion in the reconstructed image is removed,
thereby increasing the image quality. Our scheme combines these two
methods. Experimental results on standard image Lena show that our
scheme can give a reconstructed image with a PSNR value of 31.6 db
at 0.396 bits per pixel. Our scheme is also faster than the existing VQ
variants.
Abstract: Implicit equations play a crucial role in Engineering.
Based on this importance, several techniques have been applied to
solve this particular class of equations. When it comes to practical
applications, in general, iterative procedures are taken into account.
On the other hand, with the improvement of computers, other
numerical methods have been developed to provide a more
straightforward methodology of solution. Analytical exact approaches
seem to have been continuously neglected due to the difficulty
inherent in their application; notwithstanding, they are indispensable
to validate numerical routines. Lagrange-s Inversion Theorem is a
simple mathematical tool which has proved to be widely applicable to
engineering problems. In short, it provides the solution to implicit
equations by means of an infinite series. To show the validity of this
method, the tree-parameter infiltration equation is, for the first time,
analytically and exactly solved. After manipulating these series,
closed-form solutions are presented as H-functions.
Abstract: The most planted cover crops in the Czech Republic
are mustard (Sinapis alba) and phacelia (Phacelia tanacetifolia
Benth.). A field trial was executed to evaluate root system size (RSS)
in eight varieties of mustard and five varieties of phacelia on two
locations, in three BBCH phases and in two years. The relationship
between RSS and aboveground biomass was inquired. The root
system was assessed by measuring its electric capacity. Aboveground
mass and root samples to be evaluated by means of a digital image
analysis were recovered in the BBCH phase 70. The yield of
aboveground biomass of mustard was always statistically
significantly higher than that of phacelia. Mustard showed a
statistically significant negative correlation between root length
density (RLD) within 10 cm and aboveground biomass weight (r = -
0.46*). Phacelia featured a statistically significant correlation
between aboveground biomass production and nitrate nitrogen
content in soil (r=0.782**).
Abstract: The impact of OO design on software quality
characteristics such as defect density and rework by mean of
experimental validation. Encapsulation, inheritance, polymorphism,
reusability, Data hiding and message-passing are the major attribute
of an Object Oriented system. In order to evaluate the quality of an
Object oriented system the above said attributes can act as indicators.
The metrics are the well known quantifiable approach to express any
attribute. Hence, in this paper we tried to formulate a framework of
metrics representing the attributes of object oriented system.
Empirical Data is collected from three different projects based on
object oriented paradigms to calculate the metrics.
Abstract: It is crucial to quantitatively evaluate the treatment of
epilepsy patients. This study was undertaken to test the hypothesis that
compared to the healthy control subjects, the epilepsy patients have
abnormal resting-state connectivity. In this study, we used the
imaginary part of coherency to measure the resting-state connectivity.
The analysis results shown that compared to the healthy control
subjects, epilepsy patients tend to have abnormal rhythm brain
connectivity over their epileptic focus.
Abstract: In this research, Response Surface Methodology (RSM) is used to investigate the effect of four controllable input variables namely: discharge current, pulse duration, pulse off time and applied voltage Surface Roughness (SR) of on Electrical Discharge Machined surface. To study the proposed second-order polynomial model for SR, a Central Composite Design (CCD) is used to estimation the model coefficients of the four input factors, which are alleged to influence the SR in Electrical Discharge Machining (EDM) process. Experiments were conducted on AISI D2 tool steel with copper electrode. The response is modeled using RSM on experimental data. The significant coefficients are obtained by performing Analysis of Variance (ANOVA) at 5% level of significance. It is found that discharge current, pulse duration, and pulse off time and few of their interactions have significant effect on the SR. The model sufficiency is very satisfactory as the Coefficient of Determination (R2) is found to be 91.7% and adjusted R2-statistic (R2 adj ) 89.6%.
Abstract: This project relates to a two-wheeled self balancing
robot for transferring loads on different locations along a path. This
robot specifically functions as a dual mode navigation to navigate
efficiently along a desired path. First, as a plurality of distance
sensors mounted at both sides of the body for collecting information
on tilt angle of the body and second, as a plurality of speed sensors
mounted at the bottom of the body for collecting information of the
velocity of the body in relative to the ground. A microcontroller for
processing information collected from the sensors and configured to
set the path and to balance the body automatically while a processor
operatively coupled to the microcontroller and configured to compute
change of the tilt and velocity of the body. A direct current motor
operatively coupled to the microcontroller for controlling the wheels
and characterized in that a remote control is operatively coupled to
the microcontroller to operate the robot in dual navigation modes.
Abstract: This paper presents Simulated Annealing based
approach to estimate solar cell model parameters. Single diode solar
cell model is used in this study to validate the proposed approach
outcomes. The developed technique is used to estimate different
model parameters such as generated photocurrent, saturation current,
series resistance, shunt resistance, and ideality factor that govern the
current-voltage relationship of a solar cell. A practical case study is
used to test and verify the consistency of accurately estimating
various parameters of single diode solar cell model. Comparative
study among different parameter estimation techniques is presented
to show the effectiveness of the developed approach.
Abstract: The sensitivity of UAVs to the atmospheric effects are
apparent. All the same the meteorological support for the UAVs
missions is often non-adequate or partly missing.
In our paper we show a new complex meteorological support
system for different types of UAVs pilots, specialists and decision
makers, too. The mentioned system has two important parts with
different forecasts approach such as the statistical and dynamical
ones.
The statistical prediction approach is based on a large
climatological data base and the special analog method which is able
to select similar weather situations from the mentioned data base to
apply them during the forecasting procedure.
The applied dynamic approach uses the specific WRF model runs
twice a day and produces 96 hours, high resolution weather forecast
for the UAV users over the Hungary. An easy to use web-based
system can give important weather information over the Carpathian
basin in Central-Europe. The mentioned products can be reached via
internet connection.
Abstract: When designing satellites, one of the major issues aside for designing its primary subsystems is to devise its thermal. The thermal management of satellites requires solving different sets of issues with regards to modelling. If the satellite is well conditioned all other parts of the satellite will have higher temperature no matter what. The main issue of thermal modelling for satellite design is really making sure that all the other points of the satellite will be within the temperature limits they are designed. The insertion of power electronics in aerospace technologies is becoming widespread and the modern electronic systems used in space must be reliable and efficient with thermal management unaffected by outer space constraints. Many advanced thermal management techniques have been developed in recent years that have application in high power electronic systems. This paper presents a Three-Dimensional Modal Transmission Line Matrix (3D-TLM) implementation of transient heat flow in space power electronics. In such kind of components heat dissipation and good thermal management are essential. Simulation provides the cheapest tool to investigate all aspects of power handling. The 3DTLM has been successful in modeling heat diffusion problems and has proven to be efficient in terms of stability and complex geometry. The results show a three-dimensional visualisation of self-heating phenomena in the device affected by outer space constraints, and will presents possible approaches for increasing the heat dissipation capability of the power modules.
Abstract: This work investigated the phenology of Parah tree
(Elateriospermum tapos) using the General Purpose Atmosphere
Plant Soil Simulator (GAPS model) to determine the amount of Plant
Available Water (PAW) in the soil. We found the correlation
between PAW and the timing of budburst and flower burst at Khao
Nan National Park, Nakhon Si Thammarat, Thailand. PAW from the
GAPS model can be used as an indicator of soil water stress. The low
amount of PAW may lead to leaf shedding in Parah trees.
Abstract: This study investigates CO2 mitigation by methanol
synthesis from flue gas CO2 and H2 generation through water
electrolysis. Electrolytic hydrogen generation is viable provided that
the required electrical power is supplied from renewable energy
resources; whereby power generation from renewable resources is yet
commercial challenging. This approach contribute to zero-emission,
moreover it produce oxygen which could be used as feedstock for
chemical process. At ZPC, however, oxygen would be utilized
through partial oxidation of methane in autothermal reactor (ATR);
this makes ease the difficulties of O2 delivery and marketing. On the
other hand, onboard hydrogen storage and consumption; in methanol
plant; make the project economically more competitive.
Abstract: Many systems in the natural world exhibit chaos or non-linear behavior, the complexity of which is so great that they appear to be random. Identification of chaos in experimental data is essential for characterizing the system and for analyzing the predictability of the data under analysis. The Lyapunov exponents provide a quantitative measure of the sensitivity to initial conditions and are the most useful dynamical diagnostic for chaotic systems. However, it is difficult to accurately estimate the Lyapunov exponents of chaotic signals which are corrupted by a random noise. In this work, a method for estimation of Lyapunov exponents from noisy time series using unscented transformation is proposed. The proposed methodology was validated using time series obtained from known chaotic maps. In this paper, the objective of the work, the proposed methodology and validation results are discussed in detail.
Abstract: Pipeline ADCs are becoming popular at high speeds
and with high resolution. This paper discusses the options of number
of bits/stage conversion techniques in pipelined ADCs and their
effect on Area, Speed, Power Dissipation and Linearity. The basic
building blocks like op-amp, Sample and Hold Circuit, sub converter,
DAC, Residue Amplifier used in every stage is assumed to be
identical. The sub converters use flash architectures. The design is
implemented using 0.18
Abstract: Huge losses in apple production are caused by pathogens that cannot be seen shortly after harvest. After-harvest thermotherapy treatments can considerably improve control of storage diseases on apples and become an alternative to chemical pesticides. In the years 2010-2012 carried out research in this area. Apples of 'Topaz' cultivar were harvested at optimal maturity time for long storage and subject to water bath treatment at 45, 50, 52, 55°C for 60, 120, 180 and 240 seconds. The control was untreated fruits. After 12 and 24 weeks and during so called simulated trade turnover the fruits were checked for their condition and the originators of diseases were determined by using the standard phytopathological methods. The most common originator of 'Topaz' apple infection during storage were the fungi of genus Gloeosporium. In this paper it was proven that for effective protection of 'Topaz' apples against diseases, thermotherapy by using water treatments at temperature range of 50-52°C is quite sufficient.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: Electronic Systems are the core of everyday lives.
They form an integral part in financial networks, mass transit,
telephone systems, power plants and personal computers. Electronic
systems are increasingly based on complex VLSI (Very Large Scale
Integration) integrated circuits. Initial electronic design automation is
concerned with the design and production of VLSI systems. The next
important step in creating a VLSI circuit is Physical Design. The
input to the physical design is a logical representation of the system
under design. The output of this step is the layout of a physical
package that optimally or near optimally realizes the logical
representation. Physical design problems are combinatorial in nature
and of large problem sizes. Darwin observed that, as variations are
introduced into a population with each new generation, the less-fit
individuals tend to extinct in the competition of basic necessities.
This survival of fittest principle leads to evolution in species. The
objective of the Genetic Algorithms (GA) is to find an optimal
solution to a problem .Since GA-s are heuristic procedures that can
function as optimizers, they are not guaranteed to find the optimum,
but are able to find acceptable solutions for a wide range of
problems. This survey paper aims at a study on Efficient Algorithms
for VLSI Physical design and observes the common traits of the
superior contributions.
Abstract: A new analytical method to predict the torsional
capacity and behavior of R.C multi-cell box girders strengthened with
carbon fiber reinforced polymer (CFRP) sheets is presented.
Modification was done on the Softened Truss Model (STM) in the
proposed method; the concrete torsional problem is solved by
combining the equilibrium conditions, compatibility conditions and
constitutive laws of materials by taking into account the confinement
of concrete with CFRP sheets. A specific algorithm is developed to
predict the torsional behavior of reinforced concrete multi-cell box
girders with or without strengthening by CFRP sheets. Applications
of the developed method as an assessment tool to strengthened multicell
box girders with CFRP and first analytical example that
demonstrate the contribution of the CFRP materials on the torsional
response is also included.
Abstract: This paper focuses on cost and profit analysis of
single-server Markovian queuing system with two priority classes. In
this paper, functions of total expected cost, revenue and profit of the
system are constructed and subjected to optimization with respect to
its service rates of lower and higher priority classes. A computing
algorithm has been developed on the basis of fast converging
numerical method to solve the system of non linear equations formed
out of the mathematical analysis. A novel performance measure of
cost and profit analysis in view of its economic interpretation for the
system with priority classes is attempted to discuss in this paper. On
the basis of computed tables observations are also drawn to enlighten
the variational-effect of the model on the parameters involved
therein.