Abstract: Autonomous vehicles offer the possibility of significant benefits to social welfare. However, fully automated cars might not be going to happen in the near further. To speed the adoption of the self-driving technologies, many governments worldwide are passing laws requiring data recorders for the testing of autonomous vehicles. Currently, the self-driving vehicle, (e.g., shuttle bus) has to be monitored from a remote control center. When an autonomous vehicle encounters an unexpected driving environment, such as road construction or an obstruction, it should request assistance from a remote operator. Nevertheless, large amounts of data, including images, radar and lidar data, etc., have to be transmitted from the vehicle to the remote center. Therefore, this paper proposes a data compression method of in-vehicle networks for remote monitoring of autonomous vehicles. Firstly, the time-series data are rearranged into a multi-dimensional signal space. Upon the arrival, for controller area networks (CAN), the new data are mapped onto a time-data two-dimensional space associated with the specific CAN identity. Secondly, the data are sampled based on differential sampling. Finally, the whole set of data are encoded using existing algorithms such as Huffman, arithmetic and codebook encoding methods. To evaluate system performance, the proposed method was deployed on an in-house built autonomous vehicle. The testing results show that the amount of data can be reduced as much as 1/7 compared to the raw data.
Abstract: We present a chronological evolution for naval telecommunication networks. We distinguish periods: with or without multiplexers, with switch systems, with federative systems, with medium switching, and with medium switching with wireless networks. This highlights the introduction of new layers and technology in the architecture. These architectures are presented using layer models of transmission, in a unified way, which enables us to integrate pre-existing models. A ship of a naval fleet has internal communications (i.e. applications' networks of the edge) and external communications (i.e. the use of the means of transmission between edges). We propose architectures, deduced from the layer model, which are the point of convergence between the networks on board and the HF, UHF radio, and satellite resources. This modelling allows to consider end-to-end naval communications, and in a more global way, that is from the user on board towards the user on shore, including transmission and networks on the shore side. The new architectures need take care of quality of services for end-to-end communications, the more remote control develops a lot and will do so in the future. Naval telecommunications will be more and more complex and will use more and more advanced technologies, it will thus be necessary to establish clear global communication schemes to grant consistency of the architectures. Our latest model has been implemented in a military naval situation, and serves as the basic architecture for the RIFAN2 network.
Abstract: In this paper, a drift assist control system is proposed for remote control (RC) cars to get the perfect drift angle. A steering servo control scheme is given powerfully to assist the drift driving. A gyroscope sensor is included to detect the machine's tail sliding and to achieve a better automatic counter-steering to prevent RC car from spinning. To analysis tire traction and vehicle dynamics is used to obtain the dynamic track of RC cars. It comes with a control gain to adjust counter-steering amount according to the sensor condition. An illustrated example of 1:10 RC drift car is given and the real-time control algorithm is realized by Arduino Uno.
Abstract: In this paper, monitoring and control of tap changer
mechanism of a transformer implementation in an Intelligent
Electronic Device (IED) is discussed. It has been a custom for
decades to provide a separate panel for on load tap changer control
for monitoring the tap position. However, this facility cannot either
record or transfer the information to remote control centers. As there
is a technology shift towards the smart grid protection and control
standards, the need for implementing remote control and monitoring
has necessitated the implementation of this feature in numerical
relays. This paper deals with the programming, settings and logic
implementation which is applicable to both IEC 61850 compatible
and non-compatible IEDs thereby eliminating the need for separate
tap changer control equipment. The monitoring mechanism has been
implemented in a 28MVA, 110 /6.9kV transformer with 16 tap
position with GE make T60 IED at Ultratech cement limited
Gulbarga, Karnataka and is in successful service.
Abstract: This paper introduces a video sharing platform based
on WiFi, which consists of camera, mobile phone and PC server. This
platform can receive wireless signal from the camera and show the live
video on the mobile phone captured by camera. In addition, it is able to
send commands to camera and control the camera’s holder to rotate.
The platform can be applied to interactive teaching and dangerous
area’s monitoring and so on. Testing results show that the platform can
share the live video of mobile phone. Furthermore, if the system’s PC
server and the camera and many mobile phones are connected
together, it can transfer photos concurrently.
Abstract: In new energy development, wind power has boomed.
It is due to the proliferation of wind parks and their operation in
supplying the national electric grid with low cost and clean resources.
Hence, there is an increased need to establish a proactive
maintenance for wind turbine machines based on remote control and
monitoring. That is necessary with a real-time wireless connection in
offshore or inaccessible locations while the wired method has many
flaws. The objective of this strategy is to prolong wind turbine
lifetime and to increase productivity. The hardware of a remote
control and monitoring system for wind turbine parks is designed. It
takes advantage of GPRS or Wi-Max wireless module to collect data
measurements from different wind machine sensors through IP based
multi-hop communication. Computer simulations with Proteus ISIS
and OPNET software tools have been conducted to evaluate the
performance of the studied system. Study findings show that the
designed device is suitable for application in a wind park.
Abstract: The paper describes software for remote control and measuring with new Graphical User Interface for Rohde & Schwarz instruments. Software allows remote control through Ethernet and supports basic and advanced functions for control various type of instruments like network and spectrum analyzers, power meters, signal generators and oscilloscopes. Standard Commands for Programmable Instruments (SCPI) and Virtual Instrument Software Architecture (VISA) are used for remote control and setup of instruments. Developed software is modular with user friendly graphic user interface for each instrument with automatic identification of instruments.
Abstract: In this paper, an energy efficient digital baseband circuit for piezoelectric (PE) harvester powered batteryless remote control system is presented. Pulse mode PE harvester, which provides short duration of energy, is adopted to replace conventional chemical battery in wireless remote controller. The transmitter digital baseband repeats the control command transmission once the digital circuit is initiated by the power-on-reset. A power efficient data frame format is proposed to maximize the transmission repetition time. By using the proposed frame format and receiver clock and data recovery method, the receiver baseband is able to decode the command even when the received data has 20% error. The proposed transmitter and receiver baseband are implemented using FPGA and simulation results are presented.
Abstract: A packet analyzer is a tool for debugging sensor
network systems and is convenient for developers. In this paper, we
introduce a new packet analyzer based on an embedded system. The
proposed packet analyzer is compatible with IEEE 802.15.4, which is
suitable for the wireless communication standard for sensor networks,
and is available for remote control by adopting a server-client scheme
based on the Ethernet interface. To confirm the operations of the
packet analyzer, we have developed two types of sensor nodes based
on PIC4620 and ATmega128L microprocessors and tested the
functions of the proposed packet analyzer by obtaining the packets
from the sensor nodes.
Abstract: Using Internet communication, new home electronics
have functions of monitoring and control from remote. However in
many case these electronics work as standalone, and old electronics
are not followed. Then, we developed the total remote system include
not only new electronics but olds. This systems node is a adapter of
electrical power plug that embed relay switch and some sensors, and
these nodes communicate with each other. the system server was build
on the Internet, and users access to this system from web browsers.
To reduce the cost to set up of this system, communication between
adapters are used ZigBee wireless network instead of wired LAN
cable[3]. From measured RSSI(received signal strength indicator)
information between each nodes, the system can estimate roughly
adapters were mounted on which room, and where in the room. So
also it reduces the cost of mapping nodes. Using this system, energy
saving and house monitoring are expected.
Abstract: This paper discusses the development of wireless
structure control of an induction motor scalar drives. This was
realised up on the wireless WiFi networks. This strategy of control is
ensured by the use of Wireless ad hoc networks and a virtual network
interface based on VNC which is used to make possible to take the
remote control of a PC connected on a wireless Ethernet network.
Verification of the proposed strategy of control is provided by
experimental realistic tests on scalar controlled induction motor
drives. The experimental results of the implementations with their
analysis are detailed.
Abstract: An electric power system includes a generating, a
transmission, a distribution, and consumers subsystems. An electrical
power network in Tanzania keeps growing larger by the day and
become more complex so that, most utilities have long wished for
real-time monitoring and remote control of electrical power system
elements such as substations, intelligent devices, power lines,
capacitor banks, feeder switches, fault analyzers and other physical
facilities. In this paper, the concept of automation of management of
power systems from generation level to end user levels was
determined by using Power System Simulator for Engineering
(PSS/E) version 30.3.2.
Abstract: Nowadays, new home appliances and office appliances
have been developed that communicate with users through the
Internet, for remote monitor and remote control. However, developments
and sales of these new appliances are just started, then,
many products in our houses and offices do not have these useful
functions. In few years, we add these new functions to the outlet,
it means multifunctional electrical power socket plug adapter. The
outlet measure power consumption of connecting appliances, and it
can switch power supply to connecting appliances, too. Using this
outlet, power supply of old appliances can be control and monitor.
And we developed the interface system using web browser to operate
it from users[1]. But, this system need to set up LAN cables between
outlets and so on. It is not convenience that cables around rooms. In
this paper, we develop the system that use wireless mobile ad hoc
network instead of wired LAN to communicate with the outlets.
Abstract: This project relates to a two-wheeled self balancing
robot for transferring loads on different locations along a path. This
robot specifically functions as a dual mode navigation to navigate
efficiently along a desired path. First, as a plurality of distance
sensors mounted at both sides of the body for collecting information
on tilt angle of the body and second, as a plurality of speed sensors
mounted at the bottom of the body for collecting information of the
velocity of the body in relative to the ground. A microcontroller for
processing information collected from the sensors and configured to
set the path and to balance the body automatically while a processor
operatively coupled to the microcontroller and configured to compute
change of the tilt and velocity of the body. A direct current motor
operatively coupled to the microcontroller for controlling the wheels
and characterized in that a remote control is operatively coupled to
the microcontroller to operate the robot in dual navigation modes.
Abstract: This document describes an electronic speed control designed to drive two DC motors from a 6 V battery pack to be controlled by a commercial universal infrared remote control hand set. Conceived for a tank-like vehicle, one motor drives the left side wheels or tracks and the other motor drives the right side. As it is shown here, there is a left-right steering input and a forward– backward throttles input, like would be used on a model car. It is designed using a microcontroller PIC16F873A.
Abstract: This paper presents design features of a rescue robot, named CEO Mission II. Its body is designed to be the track wheel type with double front flippers for climbing over the collapse and the rough terrain. With 125 cm. long, 5-joint mechanical arm installed on the robot body, it is deployed not only for surveillance from the top view but also easier and faster access to the victims to get their vital signs. Two cameras and sensors for searching vital signs are set up at the tip of the multi-joint mechanical arm. The third camera is at the back of the robot for driving control. Hardware and software of the system, which controls and monitors the rescue robot, are explained. The control system is used for controlling the robot locomotion, the 5-joint mechanical arm, and for turning on/off devices. The monitoring system gathers all information from 7 distance sensors, IR temperature sensors, 3 CCD cameras, voice sensor, robot wheels encoders, yawn/pitch/roll angle sensors, laser range finder and 8 spare A/D inputs. All sensors and controlling data are communicated with a remote control station via IEEE 802.11b Wi-Fi. The audio and video data are compressed and sent via another IEEE 802.11g Wi-Fi transmitter for getting real-time response. At remote control station site, the robot locomotion and the mechanical arm are controlled by joystick. Moreover, the user-friendly GUI control program is developed based on the clicking and dragging method to easily control the movement of the arm. Robot traveling map is plotted from computing the information of wheel encoders and the yawn/pitch data. 2D Obstacle map is plotted from data of the laser range finder. The concept and design of this robot can be adapted to suit many other applications. As the Best Technique awardee from Thailand Rescue Robot Championship 2006, all testing results are satisfied.
Abstract: In this paper, a multi-agent robot system is presented. The system consists of four robots. The developed robots are able to automatically enter and patrol a harmful environment, such as the building infected with virus or the factory with leaking hazardous gas. Further, every robot is able to perform obstacle avoidance and search for the victims. Several operation modes are designed: remote control, obstacle avoidance, automatic searching, and so on.
Abstract: This paper presents a wrap-around view system with 4
smart cameras module and remote motion mobile robot control equipped with smart camera module system. The two-level scheme for
remote motion control with smart-pad(IPAD) is introduced on this
paper. In the low-level, the wrap-around view system is controlled or operated to keep the reference points lying around top view image
plane. On the higher level, a robot image based motion controller is utilized to drive the mobile platform to reach the desired position or
track the desired motion planning through image feature feedback. The
design wrap-around view system equipped on presents such advantages as follows: 1) a satisfactory solution for the FOV and affine
problem; 2) free of any complex and constraint with robot pose. The performance of the wrap-around view equipped on mobile robot
remote control is proven by experimental results.