Abstract: Since the 80s huge efforts have been made to utilize
renewable energy sources to generate electric power. This paper
reports some aspects of integration of the distributed generators into
the low voltage distribution networks. An assessment of impact of the
distributed generators on the reliability indices of low voltage
network is performed. Results obtained from case study using low
voltage network, are presented and discussed.
Abstract: A diamond-like carbon (DLC) based solid-lubricant
film was designed and DLC films were successfully prepared using a
microwave plasma enhanced magnetron sputtering deposition
technology. Post-test characterizations including Raman
spectrometry, X-ray diffraction, nano-indentation test, adhesion test,
friction coefficient test were performed to study the influence of
substrate bias voltage on the mechanical properties of the W- and
S-doped DLC films. The results indicated that the W- and S-doped
DLC films also had the typical structure of DLC films and a better
mechanical performance achieved by the application of a substrate
bias of -200V.
Abstract: Physical urban form is recognized to be the media for
human transactions. It directly influences the travel demand of people
in a specific urban area and the amount of energy used for
transportation. Distorted, sprawling form often creates sustainability
problems in urban areas. It is declared in EU strategic planning
documents that compact urban form and mixed land use pattern must
be given the main focus to achieve better sustainability in urban
areas, but the methods to measure and compare these characteristics
are still not clear.
This paper presents the simple methods to measure the spatial
characteristics of urban form by analyzing the location and
distribution of objects in an urban environment. The extended CA
(cellular automata) model is used to simulate urban development
scenarios.
Abstract: Medical negligence disputes in Malaysia are mainly resolved through litigation by using the tort system. The tort system, being adversarial in nature has subjected parties to litigation hazards such as delay, excessive costs and uncertainty of outcome. The dissatisfaction of the tort system in compensating medically injured victims has created various alternatives to litigation. Amongst them is the implementation of a no-fault compensation system which would allow compensation to be given without the need of proving fault on the medical personnel. Instead, the community now bears the burden of compensating and at the end, promotes collective responsibility. For Malaysia, introducing a no-fault system would provide a tempting solution and may ultimately, achieve justice for the medical injured victims. Nevertheless, such drastic change requires a great deal of consideration to determine the suitability of the system and whether or not it will eventually cater for the needs of the Malaysian population
Abstract: The consumption of lactose in acid cheese whey
anaerobic fermentation process under fed-batch conditions was
studied. During fermentation for 100 hours the biogas production
(CO2 and CH4) was analyzed online. Among the standard analyses
FT-IR spectroscopy was used to follow the consumption of lactose by
bacteria. The absorption bands at 990, 894 and 787 cm-1 in the 2nd
derivative spectra were shown to be characteristic for lactose and
were used to follow the lactose conversion. It was shown that acid
cheese whey lactose was converted by bacteria in first 7 hours. In the
spectra of 17, 18 and 95 hour fermentation samples lactose was not
identified and these results correlated with the HPLC data.
Abstract: The crossed cube is one of the most notable variations of hypercube, but some properties of the former are superior to those of the latter. For example, the diameter of the crossed cube is almost the half of that of the hypercube. In this paper, we focus on the problem embedding a Hamiltonian cycle through an arbitrary given edge in the crossed cube. We give necessary and sufficient condition for determining whether a given permutation with n elements over Zn generates a Hamiltonian cycle pattern of the crossed cube. Moreover, we obtain a lower bound for the number of different Hamiltonian cycles passing through a given edge in an n-dimensional crossed cube. Our work extends some recently obtained results.
Abstract: In this paper we present a soft timing phase estimation (STPE) method for wireless mobile receivers operating in low signal to noise ratios (SNRs). Discrete Polyphase Matched (DPM) filters, a Log-maximum a posterior probability (MAP) and/or a Soft-output Viterbi algorithm (SOVA) are combined to derive a new timing recovery (TR) scheme. We apply this scheme to wireless cellular communication system model that comprises of a raised cosine filter (RCF), a bit-interleaved turbo-coded multi-level modulation (BITMM) scheme and the channel is assumed to be memory-less. Furthermore, no clock signals are transmitted to the receiver contrary to the classical data aided (DA) models. This new model ensures that both the bandwidth and power of the communication system is conserved. However, the computational complexity of ideal turbo synchronization is increased by 50%. Several simulation tests on bit error rate (BER) and block error rate (BLER) versus low SNR reveal that the proposed iterative soft timing recovery (ISTR) scheme outperforms the conventional schemes.
Abstract: Happening of Ferroresonance phenomenon is one of the reasons of consuming and ruining transformers, so recognition of Ferroresonance phenomenon has a special importance. A novel method for classification of Ferroresonance presented in this paper. Using this method Ferroresonance can be discriminate from other transients such as capacitor switching, load switching, transformer switching. Wavelet transform is used for decomposition of signals and Competitive Neural Network used for classification. Ferroresonance data and other transients was obtained by simulation using EMTP program. Using Daubechies wavelet transform signals has been decomposed till six levels. The energy of six detailed signals that obtained by wavelet transform are used for training and trailing Competitive Neural Network. Results show that the proposed procedure is efficient in identifying Ferroresonance from other events.
Abstract: Bio-chips are used for experiments on genes and
contain various information such as genes, samples and so on. The
two-dimensional bio-chips, in which one axis represent genes and the
other represent samples, are widely being used these days. Instead of
experimenting with real genes which cost lots of money and much
time to get the results, bio-chips are being used for biological
experiments. And extracting data from the bio-chips with high
accuracy and finding out the patterns or useful information from such
data is very important. Bio-chip analysis systems extract data from
various kinds of bio-chips and mine the data in order to get useful
information. One of the commonly used methods to mine the data is
classification. The algorithm that is used to classify the data can be
various depending on the data types or number characteristics and so
on. Considering that bio-chip data is extremely large, an algorithm that
imitates the ecosystem such as the ant algorithm is suitable to use as an
algorithm for classification. This paper focuses on finding the
classification rules from the bio-chip data using the Ant Colony
algorithm which imitates the ecosystem. The developed system takes
in consideration the accuracy of the discovered rules when it applies it
to the bio-chip data in order to predict the classes.
Abstract: Knowledge Discovery of Databases (KDD) is the
process of extracting previously unknown but useful and significant
information from large massive volume of databases. Data Mining is
a stage in the entire process of KDD which applies an algorithm to
extract interesting patterns. Usually, such algorithms generate huge
volume of patterns. These patterns have to be evaluated by using
interestingness measures to reflect the user requirements.
Interestingness is defined in different ways, (i) Objective measures
(ii) Subjective measures. Objective measures such as support and
confidence extract meaningful patterns based on the structure of the
patterns, while subjective measures such as unexpectedness and
novelty reflect the user perspective. In this report, we try to brief the
more widely spread and successful subjective measures and propose
a new subjective measure of interestingness, i.e. shocking.
Abstract: Green Lean Total Quality Management (TQM)
System is a system comprises of Environmental Management System
(EMS) practices which is integrated to TQM with Lean
Manufacturing (LM) principles. The ultimate goal of this system is to
focus on achieving total customer satisfaction and environmental care by removing eight wastes available in any process in an
organization. A survey questionnaire was developed and distributed to 30 highly active automotive vendors in Malaysia and analyzed by
SPSS v.17. It was found out that some vendors have been practicing TQM and LM while some have started to implement EMS. This
study is only focusing on highly active companies that have been involved in MAJAICO Program and Proton Vendor Development
Program. This is the first study conducted to know the current status of TQM, LM and EMS practices in highly active automotive companies in Malaysia. It was found out that EMS has been
practiced by 16 companies out of 30. Within these 16 companies the
approach is more holistic and green. This is a preliminary study that combined 4 awards practices, ISO/TS16949, Toyota Production
System SAEJ4000, MAJAICO Lean Production System and EMS.
Abstract: Self-Excited Induction Generator (SEIG) builds up voltage while it enters in its magnetic saturation region. Due to non-linear magnetic characteristics, the performance analysis of SEIG involves cumbersome mathematical computations. The dependence of air-gap voltage on saturated magnetizing reactance can only be established at rated frequency by conducting a laboratory test commonly known as synchronous run test. But, there is no laboratory method to determine saturated magnetizing reactance and air-gap voltage of SEIG at varying speed, terminal capacitance and other loading conditions. For overall analysis of SEIG, prior information of magnetizing reactance, generated frequency and air-gap voltage is essentially required. Thus, analytical methods are the only alternative to determine these variables. Non-existence of direct mathematical relationship of these variables for different terminal conditions has forced the researchers to evolve new computational techniques. Artificial Neural Networks (ANNs) are very useful for solution of such complex problems, as they do not require any a priori information about the system. In this paper, an attempt is made to use cascaded neural networks to first determine the generated frequency and magnetizing reactance with varying terminal conditions and then air-gap voltage of SEIG. The results obtained from the ANN model are used to evaluate the overall performance of SEIG and are found to be in good agreement with experimental results. Hence, it is concluded that analysis of SEIG can be carried out effectively using ANNs.
Abstract: A heuristic conceptual model for to develop the
Reliability Centered Maintenance (RCM), especially in preventive
strategy, has been explored during this paper. In most real cases
which complicity of system obligates high degree of reliability, this
model proposes a more appropriate reliability function between life
time distribution based and another which is based on relevant
Extreme Value (EV) distribution. A statistical and mathematical
approach is used to estimate and verify these two distribution
functions. Then best one is chosen just among them, whichever is
more reliable. A numeric Industrial case study will be reviewed to
represent the concepts of this paper, more clearly.
Abstract: Endemic Artemia franciscana populations can be found throughout the American continent and also as an introduced specie in several country all over the world, such as in the Mediterranean region where Artemia franciscana was identified as an invasive specie replacing native Artemia parthenogenetica and Artemia salina. In the present study, the characterization of the new invasive Artemia franciscana reported from Sabkhet Halk El-Menzel (Tunisia) was done based on the cysts biometry, nauplii instar-I length, Adult sexual dimorphism and fatty acid profile. The mean value of the diameter of non-decapsulated and decapsulated cysts, chorion thickness and naupliar length is 235.8, 226.3, 4.75 and 426.8 μm, respectively. Sexual dimorphism for adults specimen showed that maximal distance between compound eyes, diameter for compound eyes, length of first antenna and the abdomen length compared to the total body length ratio, are the most important variables for males and females discrimination with a total contribution of 62.39 %. The analysis of fatty acid methyl esters profile of decapsulated cysts resulted in low levels of linolenic acid (LLA, C18:3n-3) and high levels of eicosapentaenoic acid (EPA, C20:5n-3) with 3.11 and 11.10 %, respectively. Low quantity of docosahexaenoic acid (DHA, 22:6n-3) was also observed with 0.17 mg.g-1 dry weight.
Abstract: This paper discusses EM algorithm and Bootstrap
approach combination applied for the improvement of the satellite
image fusion process. This novel satellite image fusion method based
on estimation theory EM algorithm and reinforced by Bootstrap
approach was successfully implemented and tested. The sensor
images are firstly split by a Bayesian segmentation method to
determine a joint region map for the fused image. Then, we use the
EM algorithm in conjunction with the Bootstrap approach to develop
the bootstrap EM fusion algorithm, hence producing the fused
targeted image. We proposed in this research to estimate the
statistical parameters from some iterative equations of the EM
algorithm relying on a reference of representative Bootstrap samples
of images. Sizes of those samples are determined from a new
criterion called 'hybrid criterion'. Consequently, the obtained results
of our work show that using the Bootstrap EM (BEM) in image
fusion improve performances of estimated parameters which involve
amelioration of the fused image quality; and reduce the computing
time during the fusion process.
Abstract: This paper presents a new approach using Combined Artificial Neural Network (CANN) module for daily peak load forecasting. Five different computational techniques –Constrained method, Unconstrained method, Evolutionary Programming (EP), Particle Swarm Optimization (PSO), and Genetic Algorithm (GA) – have been used to identify the CANN module for peak load forecasting. In this paper, a set of neural networks has been trained with different architecture and training parameters. The networks are trained and tested for the actual load data of Chennai city (India). A set of better trained conventional ANNs are selected to develop a CANN module using different algorithms instead of using one best conventional ANN. Obtained results using CANN module confirm its validity.
Abstract: Polynomial bases and normal bases are both used for
elliptic curve cryptosystems, but field arithmetic operations such as
multiplication, inversion and doubling for each basis are implemented
by different methods. In general, it is said that normal bases, especially
optimal normal bases (ONB) which are special cases on normal bases,
are efficient for the implementation in hardware in comparison with
polynomial bases. However there seems to be more examined by
implementing and analyzing these systems under similar condition. In
this paper, we designed field arithmetic operators for each basis over
GF(2233), which field has a polynomial basis recommended by SEC2
and a type-II ONB both, and analyzed these implementation results.
And, in addition, we predicted the efficiency of two elliptic curve
cryptosystems using these field arithmetic operators.
Abstract: A feed-forward, back-propagation Artificial Neural
Network (ANN) model has been used to forecast the occurrences of
wastewater overflows in a combined sewerage reticulation system.
This approach was tested to evaluate its applicability as a method
alternative to the common practice of developing a complete
conceptual, mathematical hydrological-hydraulic model for the
sewerage system to enable such forecasts. The ANN approach
obviates the need for a-priori understanding and representation of the
underlying hydrological hydraulic phenomena in mathematical terms
but enables learning the characteristics of a sewer overflow from the
historical data.
The performance of the standard feed-forward, back-propagation
of error algorithm was enhanced by a modified data normalizing
technique that enabled the ANN model to extrapolate into the
territory that was unseen by the training data. The algorithm and the
data normalizing method are presented along with the ANN model
output results that indicate a good accuracy in the forecasted sewer
overflow rates. However, it was revealed that the accurate
forecasting of the overflow rates are heavily dependent on the
availability of a real-time flow monitoring at the overflow structure
to provide antecedent flow rate data. The ability of the ANN to
forecast the overflow rates without the antecedent flow rates (as is
the case with traditional conceptual reticulation models) was found to
be quite poor.
Abstract: This study created new graphical icons and operating
functions in a CAD/CAM software system by analyzing icons in some
of the popular systems, such as AutoCAD, AlphaCAM, Mastercam
and the 1st edition of LiteCAM. These software systems all focused on
geometric design and editing, thus how to transmit messages
intuitively from icon itself to users is an important function of
graphical icons. The primary purpose of this study is to design
innovative icons and commands for new software.
This study employed the TRIZ method, an innovative design
method, to generate new concepts systematically. Through literature
review, it then investigated and analyzed the relationship between
TRIZ and idea development. Contradiction Matrix and 40 Principles
were used to develop an assisting tool suitable for icon design in
software development. We first gathered icon samples from the
selected CAD/CAM systems. Then grouped these icons by
meaningful functions, and compared useful and harmful properties.
Finally, we developed new icons for new software systems in order to
avoid intellectual property problem.
Abstract: Drying characteristics of rough rice (variety of lenjan) with an initial moisture content of 25% dry basis (db) was studied in a hot air dryer assisted by infrared heating. Three arrival air temperatures (30, 40 and 500C) and four infrared radiation intensities (0, 0.2 , 0.4 and 0.6 W/cm2) and three arrival air speeds (0.1, 0.15 and 0.2 m.s-1) were studied. Bending strength of brown rice kernel, percentage of cracked kernels and time of drying were measured and evaluated. The results showed that increasing the drying arrival air temperature and radiation intensity of infrared resulted decrease in drying time. High bending strength and low percentage of cracked kernel was obtained when paddy was dried by hot air assisted infrared dryer. Between this factors and their interactive effect were a significant difference (p