Abstract: This paper attempts to model and design a simple
fuzzy logic controller with Variable Reference. The Variable
Reference (VR) is featured as an adaptability element which is
obtained from two known variables – desired system-input and actual
system-output. A simple fuzzy rule-based technique is simulated to
show how the actual system-input is gradually tuned in to a value
that closely matches the desired input. The designed controller is
implemented and verified on a simple heater which is controlled by
PIC Microcontroller harnessed by a code developed in embedded C.
The output response of the PIC-controlled heater is analyzed and
compared to the performances by conventional fuzzy logic
controllers. The novelty of this work lies in the fact that it gives
better performance by using less number of rules compared to
conventional fuzzy logic controllers.
Abstract: This paper is concerned with the existence and unique¬ness of pseudo-almost periodic solutions to the chaotic delayed neural networks (t)= —Dx(t) ± A f (x (t)) B f (x (t — r)) C f (x(p))dp J (t) . t-o Under some suitable assumptions on A, B, C, D, J and f, the existence and uniqueness of a pseudo-almost periodic solution to equation above is obtained. The results of this paper are new and they complement previously known results.
Abstract: This paper discusses the Urdu script characteristics,
Urdu Nastaleeq and a simple but a novel and robust technique to
recognize the printed Urdu script without a lexicon. Urdu being a
family of Arabic script is cursive and complex script in its nature, the
main complexity of Urdu compound/connected text is not its
connections but the forms/shapes the characters change when it is
placed at initial, middle or at the end of a word. The characters
recognition technique presented here is using the inherited
complexity of Urdu script to solve the problem. A word is scanned
and analyzed for the level of its complexity, the point where the level
of complexity changes is marked for a character, segmented and
feeded to Neural Networks. A prototype of the system has been
tested on Urdu text and currently achieves 93.4% accuracy on the
average.
Abstract: A word recognition architecture based on a network
of neural associative memories and hidden Markov models has been
developed. The input stream, composed of subword-units like wordinternal
triphones consisting of diphones and triphones, is provided
to the network of neural associative memories by hidden Markov
models. The word recognition network derives words from this input
stream. The architecture has the ability to handle ambiguities on
subword-unit level and is also able to add new words to the
vocabulary during performance. The architecture is implemented to
perform the word recognition task in a language processing system
for understanding simple command sentences like “bot show apple".
Abstract: The approaches to make an agent generate intelligent actions in the AI field might be roughly categorized into two ways–the classical planning and situated action system. It is well known that each system have its own strength and weakness. However, each system also has its own application field. In particular, most of situated action systems do not directly deal with the logical problem. This paper first briefly mentions the novel action generator to situatedly extract a set of actions, which is likely to help to achieve the goal at the current situation in the relaxed logical space. After performing the action set, the agent should recognize the situation for deciding the next likely action set. However, since the extracted action is an approximation of the action which helps to achieve the goal, the agent could be caught into the deadlock of the problem. This paper proposes the newly developed hybrid architecture to solve the problem, which combines the novel situated action generator with the conventional planner. The empirical result in some planning domains shows that the quality of the resultant path to the goal is mostly acceptable as well as deriving the fast response time, and suggests the correlation between the structure of problems and the organization of each system which generates the action.
Abstract: Potassium monopersulfate has been decomposed in aqueous solution in the presence of Co(II). The process has been simulated by means of a mechanism based on elementary reactions. Rate constants have been taken from literature reports or, alternatively, assimilated to analogous reactions occurring in Fenton's chemistry. Several operating conditions have been successfully applied.
Abstract: This paper presents the mathematical model and
control strategy on DQ frame of shunt active power filter. The
structure of the shunt active power filter is the voltage source inverter
(VSI). The pulse width modulation (PWM) with PI controller is used
in the paper. The concept of DQ frame to apply with the shunt active
power filter is described. Moreover, the detail of the PI controller
design for two current loops and one voltage loop are fully explained.
The DQ axis with Fourier (DQF) method is applied to calculate the
reference currents on DQ frame. The simulation results show that the
control strategy and the design method presented in the paper can
provide the good performance of the shunt active power filter.
Moreover, the %THD of the source currents after compensation can
follow the IEEE Std.519-1992.
Abstract: This paper deals with automatic sentence modality
recognition in French. In this work, only prosodic features are
considered. The sentences are recognized according to the three
following modalities: declarative, interrogative and exclamatory
sentences. This information will be used to animate a talking head for
deaf and hearing-impaired children. We first statistically study a real
radio corpus in order to assess the feasibility of the automatic
modeling of sentence types. Then, we test two sets of prosodic
features as well as two different classifiers and their combination. We
further focus our attention on questions recognition, as this modality
is certainly the most important one for the target application.
Abstract: In today-s highly globalised and competitive world
access to information plays key role in having an upper hand between
business rivals. Hence, proper protection of such crucial resource is
core to any modern business. Implementing a successful information
security system is basically centered around three pillars; technical
solution involving both software and hardware, information security
controls to translate the policies and procedure in the system and the
people to implement. This paper shows that a lot needs to be done for
countries adapting information technology to process, store and
distribute information to secure adequately such core resource.
Abstract: The aim of this study is to discover secondary school students’ perceptions related to information technologies and the connections between concepts in their cognitive structures. A word association test consisting of six concepts related to information technologies is used to collect data from 244 secondary school students. Concept maps that present students’ cognitive structures are drawn with the help of frequency data. Data are analyzed and interpreted according to the connections obtained as a result of the concept maps. It is determined students associate most with these concepts—computer, Internet, and communication of the given concepts, and associate least with these concepts—computer-assisted education and information technologies. These results show the concepts, Internet, communication, and computer, are an important part of students’ cognitive structures. In addition, students mostly answer computer, phone, game, Internet and Facebook as the key concepts. These answers show students regard information technologies as a means for entertainment and free time activity, not as a means for education.
Abstract: To maximise furnace production it-s necessary to
optimise furnace control, with the objectives of achieving maximum
power input into the melting process, minimum network distortion
and power-off time, without compromise on quality and safety. This
can be achieved with on the one hand by an appropriate electrode
control and on the other hand by a minimum of AC transformer
switching.
Electrical arc is a stochastic process; witch is the principal cause
of power quality problems, including voltages dips, harmonic
distortion, unbalance loads and flicker. So it is difficult to make an
appropriate model for an Electrical Arc Furnace (EAF). The factors
that effect EAF operation are the melting or refining materials,
melting stage, electrode position (arc length), electrode arm control
and short circuit power of the feeder. So arc voltages, current and
power are defined as a nonlinear function of the arc length. In this
article we propose our own empirical function of the EAF and model,
for the mean stages of the melting process, thanks to the
measurements in the steel factory.
Abstract: To measure the thickness of the subcutaneous adipose
tissue layer, a non-invasive optical measurement system (λ=1300 nm)
is introduced. Animal and human subjects are used for the
experiments. The results of human subjects are compared with the data
of ultrasound device measurements, and a high correlation (r=0.94 for
n=11) is observed. There are two modes in the corresponding signals
measured by the optical system, which can be explained by
two-layered and three-layered tissue models. If the target tissue is
thinner than the critical thickness, detected data using diffuse
reflectance method follow the three-layered tissue model, so the data
increase as the thickness increases. On the other hand, if the target
tissue is thicker than the critical thickness, the data follow the
two-layered tissue model, so they decrease as the thickness increases.
Abstract: Today modern simulations solutions in the wind turbine industry have achieved a high degree of complexity and detail in result. Limitations exist when it is time to validate model results against measurements. Regarding Model validation it is of special interest to identify mode frequencies and to differentiate them from the different excitations. A wind turbine is a complex device and measurements regarding any part of the assembly show a lot of noise. Input excitations are difficult or even impossible to measure due to the stochastic nature of the environment. Traditional techniques for frequency analysis or features extraction are widely used to analyze wind turbine sensor signals, but have several limitations specially attending to non stationary signals (Events). A new technique based on autoregresive analysis techniques is introduced here for a specific application, a comparison and examples related to different events in the wind turbine operations are presented.
Abstract: The purpose of this paper is to provide an overview on methodological aspects of the information technology outsourcing (ITO) surveys, in an attempt to improve the data quality and reporting in survey research. It is based on a review of thirty articles on ITO surveys and focuses on two commonly explored dimensions of ITO, namely what are outsourced and why should there be ITO. This study highlights weaknesses in ITO surveys including lack of a clear definition of population, lack of information regarding the sampling method used, not citing the response rate, no information pertaining to pilot testing of survey instrument and absence of information on internal validity in the use or reporting of surveys. This study represents an attempt with a limited scope to point to shortfalls in the use survey methodology in ITO, and thus raise awareness among researchers in enhancing the reliability of survey findings.
Abstract: Reasonably priced and well-constructed housing must
be an integral and element supporting a healthy society. The absence
of housing everyone in society can afford negatively affects the
people's health, education, ability to get jobs, develop their
community. Without access to decent housing, economic
development, integration of immigrants and inclusiveness, the society
is negatively impacted. Canada has a sterling record in creating
housing compared to many other nations around the globe. Canadian
housing gets support from a mature and responsive mortgage network
and a top-quality construction industry as well as safe and excellent
quality building materials that are readily available. Yet 1.7 million
Canadian households occupy substandard abodes. During the past
hundred years, Canada's government has made a wide variety of
attempts to provide decent residential facilities every Canadian can
afford. Despite these laudable efforts, today Canada is left with
housing that is inadequate for many Canadians. People who own their
housing are given all kinds of privileges and perks, while people with
relatively low incomes who rent their apartments or houses are
discriminated against.
To help solve these problems, zoning that is based on an
"inclusionary" philosophy is tool developed to help provide people
the affordable residences that they need. No, thirty years after its
introduction, this type of zoning has been shown effective in helping
build and provide Canadians with a houses or apartments they can
afford to pay for. Using this form of zoning can have different results
+depending on where and how it is used. After examining Canadian
affordable housing and four American cases where this type of
zoning was enforced in the USA, this makes various
recommendations for expanding Canadians' access to housing they
can afford.
Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: This paper describes an automated event detection and location system for water distribution pipelines which is based upon low-cost sensor technology and signature analysis by an Artificial
Neural Network (ANN). The development of a low cost failure sensor which measures the opacity or cloudiness of the local water
flow has been designed, developed and validated, and an ANN based system is then described which uses time series data produced by
sensors to construct an empirical model for time series prediction and
classification of events. These two components have been installed,
tested and verified in an experimental site in a UK water distribution
system. Verification of the system has been achieved from a series of
simulated burst trials which have provided real data sets. It is concluded that the system has potential in water distribution network
management.
Abstract: This paper presents a system for tracking the movement of laparoscopic instruments which is based on an orthogonal system of webcams and video image processing. The movements are captured with two webcams placed orthogonally inside of the physical trainer. On the image, the instruments were detected by using color markers placed on the distal tip of each instrument. The 3D position of the tip of the instrument within the work space was obtained by linear triangulation method. Preliminary results showed linearity and repeatability in the motion tracking with a resolution of 0.616 mm in each axis; the accuracy of the system showed a 3D instrument positioning error of 1.009 ± 0.101 mm. This tool is a portable and low-cost alternative to traditional tracking devices and a trustable method for the objective evaluation of the surgeon’s surgical skills.
Abstract: A design of communication area for infrared
electronic-toll-collection systems to provide an extended
communication interval in the vehicle traveling direction and
regular boundary between contiguous traffic lanes is proposed.
By utilizing two typical low-cost commercial infrared LEDs with
different half-intensity angles Φ1/2 = 22◦ and 10◦, the radiation
pattern of the emitter is designed to properly adjust the spatial
distribution of the signal power. The aforementioned purpose
can be achieved with an LED array in a three-piece structure
with appropriate mounting angles. With this emitter, the influence
of the mounting parameters, including the mounting height and
mounting angles of the on-board unit and road-side unit, on the
system performance in terms of the received signal strength and
communication area are investigated. The results reveal that, for
our emitter proposed in this paper, the ideal ”long-and-narrow”
characteristic of the communication area is very little affected by
these mounting parameters. An optimum mounting configuration is
also suggested.
Abstract: A two-dimensional numerical simulation of the contribution
of both inertial and aerodynamic forces on the blade loads of
a Vertical-Axis Wind Turbine (VAWT) is presented. After describing
the computational model and the relative validation procedure, a
complete campaign of simulations - based on full RANS unsteady
calculations - is proposed for a three-bladed rotor architecture characterized
by a NACA 0021 airfoil. For each analyzed angular velocity,
the combined effect of pressure and viscous forces acting on every
rotor blade are compared to the corresponding centrifugal forces,
due to the revolution of the turbine, thus achieving a preliminary
estimation of the correlation between overall rotor efficiency and
structural blade loads.