Abstract: The High Voltage (HV) transmission mains into the community necessitate earthing design to ensure safety compliance of the system. Concrete poles are widely used within HV transmission mains; which could have an impact on the earth grid impedance and input impedance of the system from the fault point of view. This paper provides information on concrete pole earthing to enhance the split factor of the system; further, it discusses the deployment of concrete structures in high soil resistivity area to reduce the earth grid system of the plant. This paper introduces the cut off soil resistivity SC ρ when replacing timber poles with concrete ones.
Abstract: The electric power industry is currently undergoing an unprecedented reform. One of the most exciting and potentially profitable recent developments is increasing usage of artificial intelligence techniques. The intention of this paper is to give an overview of using neural network (NN) techniques in power systems. According to the growth rate of NNs application in some power system subjects, this paper introduce a brief overview in fault diagnosis, security assessment, load forecasting, economic dispatch and harmonic analyzing. Advantages and disadvantages of using NNs in above mentioned subjects and the main challenges in these fields have been explained, too.
Abstract: This paper is part of an ongoing research on the
development of systemic maintenance management model Malaysian
university buildings. In order to achieve this aim, there is a need to
develop a performance model against which services are measure.
Measuring performance is a significant part of maintenance
management service delivery. Maintenance organization needs to
know where they are in order to provide user-driven services and to
enhance productivity. The aim of this paper is to formulate a
template or model for university maintenance organization in
Malaysia. The model is based on literature review and survey
questionnaire and has been validated. Through grounded theory, this
paper developed a 8 points matrix for the university maintenance
organizations for measuring and improving their service delivery.
The potential of the model is guide and assists towards providing
value added service delivery through initiating maintenance
according to user value system rather than on the condition of the
building.
Abstract: This paper presents the use of the predictive fuzzy logic controller (PFLC) applied to attitude control system for agile micro-satellite. In order to reduce the effect of unpredictable time delays and large uncertainties, the algorithm employs predictive control to predict the attitude of the satellite. Comparison of the PFLC and conventional fuzzy logic controller (FLC) is presented to evaluate the performance of the control system during attitude maneuver. The two proposed models have been analyzed with the same level of noise and external disturbances. Simulation results demonstrated the feasibility and advantages of the PFLC on the attitude determination and control system (ADCS) of agile satellite.
Abstract: The purpose of this study was to find out the
effectiveness of neurological impress method and repeated reading
technique on reading fluency of children with learning disabilities.
Thirty primary four pupils in three public primary schools
participated in the study. There were two experimental groups and a
control. This research employed a 3 by 2 factorial matrix and the
participants were taught for one session. Two hypotheses were
formulated to guide the research. T-test was used to analyse the data
gathered, and data analysis revealed that pupils exposed to the two
treatment strategies had improvement in their reading fluency. It was
recommended that the two strategies used in the study can be used to
intervene in reading fluency problems in children with learning
disabilities.
Abstract: The transition to sustainable development requires
considerable investments from stakeholders, both financial and
immaterial. However, accounting for such investments often poses a
challenge, as ventures with intangible or non-financial returns remain
oblivious to conventional accounting techniques and risk assessment.
That such investments may significantly contribute to the welfare of
those affected may act as a driving force behind attempting to bridge
this gap. This gains crucial importance as investments must be also
backed by governments and administrations; entities whose budget
depends on taxpayers- contributions and whose tasks are based on
securing the welfare of their citizens. Besides economic welfare,
citizens also require social and environmental wellbeing too.
However, administrations must also safeguard that welfare is
guaranteed not only to present, but to future generations too. With
already strained budgets and the requirement of sustainable
development, governments on all levels face the double challenge of
making both of these ends meet.
Abstract: Biclustering is a very useful data mining technique for
identifying patterns where different genes are co-related based on a
subset of conditions in gene expression analysis. Association rules
mining is an efficient approach to achieve biclustering as in
BIMODULE algorithm but it is sensitive to the value given to its
input parameters and the discretization procedure used in the
preprocessing step, also when noise is present, classical association
rules miners discover multiple small fragments of the true bicluster,
but miss the true bicluster itself. This paper formally presents a
generalized noise tolerant bicluster model, termed as μBicluster. An
iterative algorithm termed as BIDENS based on the proposed model
is introduced that can discover a set of k possibly overlapping
biclusters simultaneously. Our model uses a more flexible method to
partition the dimensions to preserve meaningful and significant
biclusters. The proposed algorithm allows discovering biclusters that
hard to be discovered by BIMODULE. Experimental study on yeast,
human gene expression data and several artificial datasets shows that
our algorithm offers substantial improvements over several
previously proposed biclustering algorithms.
Abstract: Research has suggested that implicit learning tasks
may rely on episodic processing to generate above chance
performance on the standard classification tasks. The current
research examines the invariant features task (McGeorge and Burton,
1990) and argues that such episodic processing is indeed important.
The results of the experiment suggest that both rejection and
similarity strategies are used by participants in this task to
simultaneously reject unfamiliar items and to accept (falsely) familiar
items. Primarily these decisions are based on the presence of low or
high frequency goal based features of the stimuli presented in the
incidental learning phase. It is proposed that a goal based analysis of
the incidental learning task provides a simple step in understanding
which features of the episodic processing are most important for
explaining the match between incidental, implicit learning and test
performance.
Abstract: The human knee joint has a three dimensional
geometry with multiple body articulations that produce complex
mechanical responses under loads that occur in everyday life and
sports activities. To produce the necessary joint compliance and
stability for optimal daily function various menisci and ligaments are
present while muscle forces are used to this effect. Therefore,
knowledge of the complex mechanical interactions of these load
bearing structures is necessary when treatment of relevant diseases is
evaluated and assisting devices are designed.
Numerical tools such as finite element analysis are suitable for
modeling such joints in order to understand their physics. They have
been used in the current study to develop an accurate human knee
joint and model its mechanical behavior. To evaluate the efficacy of
this articulated model, static load cases were used for comparison
purposes with previous experimentally verified modeling works
drawn from literature.
Abstract: The present study has been conducted to characterize
the prophenoloxidase (PPO) system of the desert locust, Schistocerca
gregaria following injection of Bacillus thuringiensis kurstaki (Bt).
The bulk of PPO system was associated with haemocytes and a little
amount was found in plasma. This system was activated by different
activators such as laminarin, lipopolysaccharide (LPS) and trypsin
suggesting that the stimulatory mechanism may involve an enzyme
cascade of one or more associated molecules. These activators did
not activate all the molecules of the cascade. Presence of
phenoloxidase activity (PO) coincides with the appearance of protein
band with molecular weight (MW) 70.154 KD (Kilo Dalton).
Abstract: Deep Brain Stimulation or DBS is the second solution
for Parkinson's Disease. Its three parameters are: frequency, pulse
width and voltage. They must be optimized to achieve successful
treatment. Nowadays it is done clinically by neurologists and there is
not certain numerical method to detect them. The aim of this research
is to introduce simulation and modeling of Parkinson's Disease
treatment as a computational procedure to select optimum voltage.
We recorded finger tremor signals of some Parkinsonian patients
under DBS treatment at constant frequency and pulse width but
variable voltages; then, we adapted a new model to fit these data. The
optimum voltages obtained by data fitting results were the same as
neurologists- commented voltages, which means modeling can be
used as an engineering method to select optimum stimulation
voltages.
Abstract: An on-demand routing protocol for wireless ad hoc
networks is one that searches for and attempts to discover a route to
some destination node only when a sending node originates a data
packet addressed to that node. In order to avoid the need for such a
route discovery to be performed before each data packet is sent, such
routing protocols must cache routes previously discovered. This
paper presents an analysis of the effect of intelligent caching in a non
clustered network, using on-demand routing protocols in wireless ad
hoc networks. The analysis carried out is based on the Dynamic
Source Routing protocol (DSR), which operates entirely on-demand.
DSR uses the cache in every node to save the paths that are learnt
during route discovery procedure. In this implementation, caching
these paths only at intermediate nodes and using the paths from these
caches when required is tried. This technique helps in storing more
number of routes that are learnt without erasing the entries in the
cache, to store a new route that is learnt.
The simulation results on DSR have shown that this technique
drastically increases the available memory for caching the routes
discovered without affecting the performance of the DSR routing
protocol in any way, except for a small increase in end to end delay.
Abstract: Insulation used in transformer is mostly oil pressboard insulation. Insulation failure is one of the major causes of catastrophic failure of transformers. It is established that partial discharges (PD) cause insulation degradation and premature failure of insulation. Online monitoring of PDs can reduce the risk of catastrophic failure of transformers. There are different techniques of partial discharge measurement like, electrical, optical, acoustic, opto-acoustic and ultra high frequency (UHF). Being non invasive and non interference prone, acoustic emission technique is advantageous for online PD measurement. Acoustic detection of p.d. is based on the retrieval and analysis of mechanical or pressure signals produced by partial discharges. Partial discharges are classified according to the origin of discharges. Their effects on insulation deterioration are different for different types. This paper reports experimental results and analysis for classification of partial discharges using acoustic emission signal of laboratory simulated partial discharges in oil pressboard insulation system using three different electrode systems. Acoustic emission signal produced by PD are detected by sensors mounted on the experimental tank surface, stored on an oscilloscope and fed to computer for further analysis. The measured AE signals are analyzed using discrete wavelet transform analysis and wavelet packet analysis. Energy distribution in different frequency bands of discrete wavelet decomposed signal and wavelet packet decomposed signal is calculated. These analyses show a distinct feature useful for PD classification. Wavelet packet analysis can sort out any misclassification arising out of DWT in most cases.
Abstract: The counting process of cell colonies is always a long
and laborious process that is dependent on the judgment and ability
of the operator. The judgment of the operator in counting can vary in
relation to fatigue. Moreover, since this activity is time consuming it
can limit the usable number of dishes for each experiment. For these
purposes, it is necessary that an automatic system of cell colony
counting is used. This article introduces a new automatic system of
counting based on the elaboration of the digital images of cellular
colonies grown on petri dishes. This system is mainly based on the
algorithms of region-growing for the recognition of the regions of
interest (ROI) in the image and a Sanger neural net for the
characterization of such regions. The better final classification is
supplied from a Feed-Forward Neural Net (FF-NN) and confronted
with the K-Nearest Neighbour (K-NN) and a Linear Discriminative
Function (LDF). The preliminary results are shown.
Abstract: Copper based composites reinforced with WC and Ti
particles were prepared using planetary ball-mill. The experiment
was designed by using Taguchi technique and milling was carried out
in an air for several hours. The powder was characterized before and
after milling using the SEM, TEM and X-ray for microstructure and
for possible new phases. Microstructures show that milled particles
size and reduction in particle size depend on many parameters. The
distance d between planes of atoms estimated from X-ray powder
diffraction data and TEM image. X-ray diffraction patterns of the
milled powder did not show clearly any new peak or energy shift, but
the TEM images show a significant change in crystalline structure of
corporate on titanium in the composites.
Abstract: A dead leg is a typical subsea production system
component. CFD is required to model heat transfer within the dead
leg. Unfortunately its solution is time demanding and thus not
suitable for fast prediction or repeated simulations. Therefore there is
a need to create a thermal FEA model, mimicking the heat flows and
temperatures seen in CFD cool down simulations.
This paper describes the conventional way of tuning and a new
automated way using parametric model order reduction (PMOR)
together with an optimization algorithm. The tuned FE analyses
replicate the steady state CFD parameters within a maximum error in
heat flow of 6 % and 3 % using manual and PMOR method
respectively. During cool down, the relative error of the tuned FEA
models with respect to temperature is below 5% comparing to the
CFD. In addition, the PMOR method obtained the correct FEA setup
five times faster than the manually tuned FEA.
Abstract: This paper considers various channels of gammaquantum
generation via an ultra-short high-power laser pulse
interaction with different targets.We analyse the possibilities to create
a pulsed gamma-radiation source using laser triggering of some
nuclear reactions and isomer targets. It is shown that sub-MeV
monochromatic short pulse of gamma-radiation can be obtained with
pulse energy of sub-mJ level from isomer target irradiated by intense
laser pulse. For nuclear reaction channel in light- atom materials, it is
shown that sub-PW laser pulse gives rise to formation about million
gamma-photons of multi-MeV energy.
Abstract: On the basis of the linearized Phillips-Herffron model of a single-machine power system, a novel method for designing unified power flow controller (UPFC) based output feedback controller is presented. The design problem of output feedback controller for UPFC is formulated as an optimization problem according to with the time domain-based objective function which is solved by iteration particle swarm optimization (IPSO) that has a strong ability to find the most optimistic results. To ensure the robustness of the proposed damping controller, the design process takes into account a wide range of operating conditions and system configurations. The simulation results prove the effectiveness and robustness of the proposed method in terms of a high performance power system. The simulation study shows that the designed controller by Iteration PSO performs better than Classical PSO in finding the solution.
Abstract: Theexperiment was carried out with 2x5 male Merino
lambs raised under intensive conditions to investigate the effect of
dietary calcium soap of linseed oil on the color and fatty acid
composition of longissimusdorsi muscle. Control lambs fed a basal
diet and the experimental lambs consumed a diet supplemented with
3% calcium soap of linseed oil. The color values (L*, a*, b* a*/b*
and chroma) were not influenced by dietary treatment. The MUFA
proportion reduced, SFA and PUFA content did not alter. As
expected, the linolenic (C18:3 n3) and thusthe n-3 content
significantly improved by linseed supplement (0.47 and 0.81; 0.78
and 1.16 in control and in experimental samples, respectively). Other
n-3 and n-6 fatty acids had similar valuestocontrol samples. The n-
6/n-3 ratio was significantly narrower in the experimental group (6.31
vs. 9.38) but the P/S ratio did not differ betweenthe two groups.In
conclusion calcium soap of linseed oil seems to be a suitable
supplement form of n-3 fatty acids to improve the nutritive value of
lamb meat.
Abstract: Current technological advances pale in comparison to the changes in social behaviors and 'sense of place' that is being empowered since the Internet made it on the scene. Today-s students view the Internet as both a source of entertainment and an educational tool. The development of virtual environments is a conceptual framework that needs to be addressed by educators and it is important that they become familiar with who these virtual learners are and how they are motivated to learn. Massively multiplayer online role playing games (MMORPGs), if well designed, could become the vehicle of choice to deliver learning content. We suggest that these games, in order to accomplish these goals, must begin with well-established instructional design principles that are co-aligned with established principles of video game design. And have the opportunity to provide an instructional model of significant prescriptive power. The authors believe that game designers need to take advantage of the natural motivation player-learners have for playing games by developing them in such a way so as to promote, intrinsic motivation, content learning, transfer of knowledge, and naturalization.