Abstract: An accurate optimal design of laminated composite
structures may present considerable difficulties due to the complexity
and multi-modality of the functional design space. The Big Bang
– Big Crunch (BB-BC) optimization method is a relatively new
technique and has already proved to be a valuable tool for structural
optimization. In the present study the exceptional efficiency of the
method is demonstrated by an example of the lay-up optimization
of multilayered anisotropic cylinders based on a three-dimensional
elasticity solution. It is shown that, due to its simplicity and speed,
the BB-BC is much more efficient for this class of problems when
compared to the genetic algorithms.
Abstract: This article gives a short preview of the new software
created especially for palletizing process in automated production
systems. Each chapter of this article is about problem solving in
development of modules in Java programming language. First part
describes structure of the software, its modules and data flow
between them. Second part describes all deployment methods, which
are implemented in the software. Next chapter is about twodimensional
editor created for manipulation with objects in each
layer of the load and gives calculations for collision control. Module
of virtual reality used for three-dimensional preview and creation of
the load is described in the fifth chapter. The last part of this article
describes communication and data flow between control system of
the robot, vision system and software.
Abstract: A three-dimensional finite element modeling for austenitic stainless steel AISI 304 annealed condition sheets of 1.0 mm thickness are developed using ABAQUS® software. This includes spot welded and weld bonded joints models. Both models undergo thermal heat caused by spot welding process and then are subjected to axial load up to the failure point. The properties of elastic and plastic regions, modulus of elasticity, fracture limit, nugget and heat affected zones are determined. Complete loaddisplacement curve for each joining model is obtained and compared with the experiment data and with the finite element models without including the effect of thermal process. In general, the results obtained for both spot welded and weld-bonded joints affected by thermal process showed an excellent agreement with the experimental data.
Abstract: For evaluating the severity of Chronic Obstructive Pulmonary Disease (COPD), one is interested in inspecting the airway wall thickening due to inflammation. Although airway segmentations have being well developed to reconstruct in high order, airway wall segmentation remains a challenge task. While tackling such problem as a multi-surface segmentation, the interrelation within surfaces needs to be considered. We propose a new method for three-dimensional airway wall segmentation using spring structural active contour model. The method incorporates the gravitational field of the image and repelling force field of the inner lumen as the soft constraint and the geometric spring structure of active contour as the hard constraint to approximate a three-dimensional coupled surface readily for thickness measurements. The results show the preservation of topology constraints of coupled surfaces. In conclusion, our springy, soft-tissue-like structure ensures the globally optimal solution and waives the shortness following by the inevitable improper inner surface constraint.
Abstract: Channel junctions can be analyzed in two ways of
division (lateral intake) and combined flows (confluence). The
present paper investigates 3D flow pattern at lateral intake using
Navier-Stokes equation and κ -ε (RNG) turbulent model. The
equations are solved by Finite-Volume Method (FVM) and results
are compared with the experimental data of (Barkdoll, B.D., 1997)
to test the validity of the findings. Comparison of the results with
the experimental data indicated a close proximity between the two
sets of data which suggest a very close simulation. Results further
indicated an inverse relation between the effects of discharge ratio
( r Q ) on the length and width of the separation zone. In other words,
as the discharge ration increases, the length and width of separation
zone decreases.
Abstract: The flow field over a flat roof model building has been numerically investigated in order to determine threedimensional CFD guidelines for the calculation of the turbulent flow over a structure immersed in an atmospheric boundary layer. To this purpose, a complete validation campaign has been performed through a systematic comparison of numerical simulations with wind tunnel experimental data. Wind tunnel measurements and numerical predictions have been compared for five different vertical positions, respectively from the upstream leading edge to the downstream bottom edge of the analyzed model. Flow field characteristics in the neighborhood of the building model have been numerically investigated, allowing a quantification of the capabilities of the CFD code to predict the flow separation and the extension of the recirculation regions. The proposed calculations have allowed the development of a preliminary procedure to be used as guidance in selecting the appropriate grid configuration and corresponding turbulence model for the prediction of the flow field over a three-dimensional roof architecture dominated by flow separation.
Abstract: In this paper, a generalized self-consistent scheme, or “three phase model", is used to set up a micro-mechanics model for rough surface contact with randomly distributed asperities. The dimensionless average real pressure p is obtained as function of the ratio of the real contact area to the apparent contact area, 0 A / A r . Both elastic and plastic materials are considered, and the influence of the plasticity of material on p is discussed. Both two-dimensional and three-dimensional rough surface contact problems are considered.
Abstract: In this paper, we have proposed a novel FinFET with
extended body under the poly gate, which is called EB-FinFET, and
its characteristic is demonstrated by using three-dimensional (3-D)
numerical simulation. We have analyzed and compared it with
conventional FinFET. The extended body height dependence on the
drain induced barrier lowering (DIBL) and subthreshold swing (S.S)
have been also investigated. According to the 3-D numerical
simulation, the proposed structure has a firm structure, an acceptable
short channel effect (SCE), a reduced series resistance, an increased
on state drain current (I
on) and a large normalized I
DS. Furthermore,
the structure can also improve corner effect and reduce self-heating
effect due to the extended body. Our results show that the EBFinFET
is excellent for nanoscale device.
Abstract: An important step in three-dimensional reconstruction
and computer vision is camera calibration, whose objective is to
estimate the intrinsic and extrinsic parameters of each camera. In this
paper, two linear methods based on the different planes are given. In
both methods, the general plane is used to replace the calibration
object with very good precision. In the first method, after controlling
the camera to undergo five times- translation movements and taking
pictures of the orthogonal planes, a set of linear constraints of the
camera intrinsic parameters is then derived by means of homography
matrix. The second method is to get all camera parameters by taking
only one picture of a given radius circle. experiments on simulated
data and real images,indicate that our method is reasonable and is a
good supplement to camera calibration.
Abstract: Direct numerical simulation (DNS) is used to study the evolution of a boundary layer that was laminar initially followed by separation and then reattachment owing to generation of turbulence. This creates a closed region of recirculation, known as the laminar-separation bubble. The present simulation emulates the flow environment encountered in a modern LP turbine blade, where a laminar separation bubble may occur on the suction surface. The unsteady, incompressible three-dimensional (3-D) Navier-Stokes (NS) equations have been solved over a flat plate in the Cartesian coordinates. The adverse pressure gradient, which causes the flow to separate, is created by a boundary condition. The separated shear layer undergoes transition through appearance of ╬ø vortices, stretching of these create longitudinal streaks. Breakdown of the streaks into small and irregular structures makes the flow turbulent downstream.
Abstract: Hydrocyclones flow field study is conducted by performing a parametric study. Effect of cone angle on deoiling hydrocyclones flow behaviour is studied in this research. Flow field of hydrocyclone is obtained by three-dimensional simulations with OpenFOAM code. Because of anisotropic behaviour of flow inside hydrocyclones LES is a suitable method to predict the flow field since it resolves large scales and model isotropic small scales. Large eddy simulation is used to predict the flow behavior of three different cone angles. Differences in tangential velocity and pressure distribution are reported in some figures.
Abstract: We present new finite element methods for Helmholtz and Maxwell equations on general three-dimensional polyhedral meshes, based on domain decomposition with boundary elements on the surfaces of the polyhedral volume elements. The methods use the lowest-order polynomial spaces and produce sparse, symmetric linear systems despite the use of boundary elements. Moreover, piecewise constant coefficients are admissible. The resulting approximation on the element surfaces can be extended throughout the domain via representation formulas. Numerical experiments confirm that the convergence behavior on tetrahedral meshes is comparable to that of standard finite element methods, and equally good performance is attained on more general meshes.
Abstract: Equal Channel Angular Pressing (ECAP) is currently
being widely investigated because of its potential to produce ultrafine
grained microstructures in metals and alloys. A sound
knowledge of the plastic deformation and strain distribution is
necessary for understanding the relationships between strain
inhomogeneity and die geometry. Considerable research has been
reported on finite element analysis of this process, assuming threedimensional
plane strain condition. However, the two-dimensional
models are not suitable due to the geometry of the dies, especially in
cylindrical ones. In the present work, three-dimensional simulation of
ECAP process was carried out for six outer corner radii (sharp to 10
mm in steps of 2 mm), with channel angle 105¶Çü▒, for strain hardening
aluminium alloy (AA 6101) using ABAQUS/Standard software.
Strain inhomogeneity is presented and discussed for all cases. Pattern
of strain variation along selected radial lines in the body of the workpiece
is presented. It is found from the results that the outer corner
has a significant influence on the strain distribution in the body of
work-piece. Based on inhomogeneity and average strain criteria,
there is an optimum outer corner radius.
Abstract: Due to the three- dimensional flow pattern interacting with bed material, the process of local scour around bridge piers is complex. Modeling 3D flow field and scour hole evolution around a bridge pier is more feasible nowadays because the computational cost and computational time have significantly decreased. In order to evaluate local flow and scouring around a bridge pier, a completely three-dimensional numerical model, SSIIM program, was used. The model solves 3-D Navier-Stokes equations and a bed load conservation equation. The model was applied to simulate local flow and scouring around a bridge pier in a large natural river with four piers. Computation for 1 day of flood condition was carried out to predict the maximum local scour depth. The results show that the SSIIM program can be used efficiently for simulating the scouring in natural rivers. The results also showed that among the various turbulence models, the k-ω model gives more reasonable results.
Abstract: By the application of an improved back-propagation
neural network (BPNN), a model of current densities for a solid oxide
fuel cell (SOFC) with 10 layers is established in this study. To build
the learning data of BPNN, Taguchi orthogonal array is applied to
arrange the conditions of operating parameters, which totally 7 factors
act as the inputs of BPNN. Also, the average current densities
achieved by numerical method acts as the outputs of BPNN.
Comparing with the direct solution, the learning errors for all learning
data are smaller than 0.117%, and the predicting errors for 27
forecasting cases are less than 0.231%. The results show that the
presented model effectively builds a mathematical algorithm to predict
performance of a SOFC stack immediately in real time.
Also, the calculating algorithms are applied to proceed with the
optimization of the average current density for a SOFC stack. The
operating performance window of a SOFC stack is found to be
between 41137.11 and 53907.89. Furthermore, an inverse predicting
model of operating parameters of a SOFC stack is developed here by
the calculating algorithms of the improved BPNN, which is proved to
effectively predict operating parameters to achieve a desired
performance output of a SOFC stack.
Abstract: For many chemical and biological processes, the understanding of the mixing phenomenon and flow behavior in a stirred tank is of major importance. A three-dimensional numerical study was performed using the software Fluent, to study the flow field in a stirred tank with a Rushton turbine. In this work, we first studied the flow generated in the tank with a Rushton turbine. Then, we studied the effect of the variation of turbine’s submergence on the thermodynamic quantities defining the flow field. For that, four submergences were considered, while maintaining the same rotational speed (N =250rpm). This work intends to optimize the aeration performances of a Rushton turbine in a stirred tank.
Abstract: During the last decade ultrafine grained (UFG) and nano-structured (NS) materials have experienced a rapid development. In this research work finite element analysis has been carried out to investigate the plastic strain distribution in equal channel angular process (ECAP). The magnitudes of Standard deviation (S. D.) and inhomogeneity index (Ci) were compared for different ECAP passes. Verification of a three-dimensional finite element model was performed with experimental tests. Finally the mechanical property including impact energy of ultrafine grained pure commercially pure Aluminum produced by severe plastic deformation method has been examined. For this aim, equal channel angular pressing die with the channel angle, outer corner angle and channel diameter of 90°, 20° and 20mm had been designed and manufactured. Commercial pure Aluminum billets were ECAPed up to four passes by route BC at the ambient temperature. The results indicated that there is a great improvement at the hardness measurement, yield strength and ultimate tensile strength after ECAP process. It is found that the magnitudes of HV reach 67HV from 21HV after the final stage of process. Also, about 330% and 285% enhancement at the YS and UTS values have been obtained after the fourth pass as compared to the as-received conditions, respectively. On the other hand, the elongation to failure and impact energy have been reduced by 23% and 50% after imposing four passes of ECAP process, respectively.
Abstract: Fatigue life prediction and evaluation are the key
technologies to assure the safety and reliability of automotive rubber
components. The objective of this study is to develop the fatigue
analysis process for vulcanized rubber components, which is
applicable to predict fatigue life at initial product design step. Fatigue
life prediction methodology of vulcanized natural rubber was
proposed by incorporating the finite element analysis and fatigue
damage parameter of maximum strain appearing at the critical location
determined from fatigue test. In order to develop an appropriate
fatigue damage parameter of the rubber material, a series of
displacement controlled fatigue test was conducted using threedimensional
dumbbell specimen with different levels of mean
displacement. It was shown that the maximum strain was a proper
damage parameter, taking the mean displacement effects into account.
Nonlinear finite element analyses of three-dimensional dumbbell
specimens were performed based on a hyper-elastic material model
determined from the uni-axial tension, equi-biaxial tension and planar
test. Fatigue analysis procedure employed in this study could be used
approximately for the fatigue design.
Abstract: In this paper, three dimensional flow characteristic was
presented by a revision of an impeller of an axial turbo fan for
improving the airflow rate and the static pressure. TO consider an
incompressible steady three-dimensional flow, the RANS equations
are used as the governing equations, and the standard k-ε turbulence
model is chosen. The pitch angles of 44°, 54°, 59°, and 64° are
implemented for the numerical model. The numerical results show that
airflow rates of each pitch angle are 1,175 CMH, 1,270 CMH, 1,340
CMH, and 800 CMH, respectively. The difference of the static
pressure at impeller inlet and outlet are 120 Pa, 214 Pa, 242 Pa, and 60
Pa according to respective pitch angles. It means that the 59° of the
impeller pitch angle is optimal to improve the airflow rate and the
static pressure.
Abstract: When designing satellites, one of the major issues aside for designing its primary subsystems is to devise its thermal. The thermal management of satellites requires solving different sets of issues with regards to modelling. If the satellite is well conditioned all other parts of the satellite will have higher temperature no matter what. The main issue of thermal modelling for satellite design is really making sure that all the other points of the satellite will be within the temperature limits they are designed. The insertion of power electronics in aerospace technologies is becoming widespread and the modern electronic systems used in space must be reliable and efficient with thermal management unaffected by outer space constraints. Many advanced thermal management techniques have been developed in recent years that have application in high power electronic systems. This paper presents a Three-Dimensional Modal Transmission Line Matrix (3D-TLM) implementation of transient heat flow in space power electronics. In such kind of components heat dissipation and good thermal management are essential. Simulation provides the cheapest tool to investigate all aspects of power handling. The 3DTLM has been successful in modeling heat diffusion problems and has proven to be efficient in terms of stability and complex geometry. The results show a three-dimensional visualisation of self-heating phenomena in the device affected by outer space constraints, and will presents possible approaches for increasing the heat dissipation capability of the power modules.