Abstract: This paper uses quasi-steady molecular statics model
and diamond tool to carry out simulation temperature rise of nanoscale
orthogonal cutting single-crystal silicon. It further qualitatively
analyzes temperature field of silicon workpiece without considering
heat transfer and considering heat transfer. This paper supposes that
the temperature rise of workpiece is mainly caused by two heat sources:
plastic deformation heat and friction heat. Then, this paper develops a
theoretical model about production of the plastic deformation heat and
friction heat during nanoscale orthogonal cutting. After the increased
temperature produced by these two heat sources are added up, the
acquired total temperature rise at each atom of the workpiece is
substituted in heat transfer finite difference equation to carry out heat
transfer and calculates the temperature field in each step and makes
related analysis.
Abstract: Development, calibration and validation of a threedimensional
model of the Legform impactor for pedestrian crash with
bumper are presented. Lower limb injury is becoming an increasingly
important concern in vehicle safety for both occupants and
pedestrians. In order to prevent lower extremity injuries to a
pedestrian when struck by a car, it is important to elucidate the
loadings from car front structures on the lower extremities and the
injury mechanism caused by these loadings. An impact test
procedure with a legform addressing lower limb injuries in car
pedestrian accidents has been proposed by EEVC/WG17. In this
study a modified legform impactor is introduced and validated
against EEVC/WG17 criteria. The finite element model of this
legform is developed using LS-DYNA software. Total mass of
legform impactor is 13.4 kg.Technical specifications including the
mass and location of the center of gravity and moment of inertia
about a horizontal axis through the respective centre of gravity in
femur and tibia are determined. The obtained results of legform
impactor static and dynamic tests are as specified in the
EEVC/WG17.
Abstract: This is the second part of the paper. It, aside from the
core subroutine test reported previously, focuses on the simulation of
turbulence governed by the full STF Navier-Stokes equations on a
large scale. Law of the wall is found plausible in this study as a model
of the boundary layer dynamics. Model validations proceed to
include velocity profiles of a stationary turbulent Couette flow, pure
sloshing flow simulations, and the identification of water-surface
inclination due to fluid accelerations. Errors resulting from the
irrotational and hydrostatic assumptions are explored when studying
a wind-driven water circulation with no shakings. Illustrative
examples show that this numerical strategy works for the simulation
of sloshing-shear mixed flow in a 3-D rigid rectangular base tank.
Abstract: E-tailing websites are often perceived to be static, impersonal and distant. However, with the movement of the World Wide Web to Web 2.0 in recent years, these online websites have been found to display personalities akin to 'humanistic' qualities and project impressions much like its retailing counterpart i.e. salespeople. This paper examines the personality of e-tailing websites and their impact on consumers- initial trust towards the sites. A total of 239 Internet users participated in this field experiment study which utilized 6 online book retailers- websites that the participants had not previously visited before. Analysis revealed that out of four website personalities (sincerity, competence, excitement and sophistication) only sincerity and competence are able to exert an influence in building consumers- trust upon their first visit to the website. The implications of the findings are further elaborated in this paper.
Abstract: Nowadays there are lots of applications of power and
free conveyors in logistics. They are the most frequently used
conveyor systems worldwide. Overhead conveyor technologies like
power and free systems are used in the most intra-logistics
applications in trade and industry. The automotive, food, beverage
and textile industry as well as aeronautic catering or engineering are
among the applications. Power and free systems employ different
manufacturing intervals in manufacturing as well as in production as
temporary store and buffer. Depending on the application area, power
and free conveyors are equipped with target controls enabling
complex distribution-and sorting tasks. This article introduces a new
power and free conveyor design in intra-logistics and explains its
components. According to the explanation of the components, a
model is created by means of their technical characteristics. Through
the CAD software, the model is visualized. After that, the static
analysis is evaluated. This analysis helps the calculation of the
mandatory state of structures under force action. This powerful model
helps companies achieve lower development costs as well as quicker
market maturity.
Abstract: The design of a steam turbine is a very complex
engineering operation that can be simplified and improved thanks to
computer-aided multi-objective optimization. This process makes use
of existing optimization algorithms and losses correlations to identify
those geometries that deliver the best balance of performance (i.e.
Pareto-optimal points).
This paper deals with a one-dimensional multi-objective and
multi-point optimization of a single-stage steam turbine. Using a
genetic optimization algorithm and an algebraic one-dimensional
ideal gas-path model based on loss and deviation correlations, a code
capable of performing the optimization of a predefined steam turbine
stage was developed. More specifically, during this study the
parameters modified (i.e. decision variables) to identify the best
performing geometries were solidity and angles both for stator and
rotor cascades, while the objective functions to maximize were totalto-
static efficiency and specific work done.
Finally, an accurate analysis of the obtained results was carried
out.
Abstract: In this paper, the computation of the electrical field distribution around AC high-voltage lines is demonstrated. The advantages and disadvantages of two different methods are described to evaluate the electrical field quantity. The first method is a seminumerical method using the laws of electrostatic techniques to simulate the two-dimensional electric field under the high-voltage overhead line. The second method which will be discussed is the finite element method (FEM) using specific boundary conditions to compute the two- dimensional electric field distributions in an efficient way.
Abstract: It is hard to percept the interaction process with machines when visual information is not available. In this paper, we have addressed this issue to provide interaction through visual techniques. Posture recognition is done for American Sign Language to recognize static alphabets and numbers. 3D information is exploited to obtain segmentation of hands and face using normal Gaussian distribution and depth information. Features for posture recognition are computed using statistical and geometrical properties which are translation, rotation and scale invariant. Hu-Moment as statistical features and; circularity and rectangularity as geometrical features are incorporated to build the feature vectors. These feature vectors are used to train SVM for classification that recognizes static alphabets and numbers. For the alphabets, curvature analysis is carried out to reduce the misclassifications. The experimental results show that proposed system recognizes posture symbols by achieving recognition rate of 98.65% and 98.6% for ASL alphabets and numbers respectively.
Abstract: This paper proposes an analytical method for the
dynamics of generating firms- alliance networks along with business
phases. Dynamics in network developments have previously been
discussed in the research areas of organizational strategy rather than in
the areas of regional cluster, where the static properties of the
networks are often discussed. The analytical method introduces the
concept of business phases into innovation processes and uses
relationships called prior experiences; this idea was developed in
organizational strategy to investigate the state of networks from the
viewpoints of tradeoffs between link stabilization and node
exploration. This paper also discusses the results of the analytical
method using five cases of the network developments of firms. The
idea of Embeddedness helps interpret the backgrounds of the
analytical results. The analytical method is useful for policymakers of
regional clusters to establish concrete evaluation targets and a
viewpoint for comparisons of policy programs.
Abstract: A theoretical study of the rigidities of slabs with
circular voids oriented in the longitudinal and in the transverse
direction is discussed. Equations are presented for predicting the
bending and torsional rigidities of the voided slabs. This paper
summarizes the results of an extensive literature search and initial
review of the current methods of analyzing voided slab. The various
methods of calculating the equivalent plate parameters, which are
necessary for two-dimensional analysis, are also reviewed. Static
deflections on voided slabs are shown to be in good agreement with
proposed equation.
Abstract: The main objectives of this study are to inspect and
identify any damage of jaimusi highway prestressed concrete bridge
after repair and strengthening of damaged structural members and to
evaluate the performance of the bridge structural members by
adopting static load test. Inspection program after repair and
strengthening includes identifying and evaluating the structural
members of bridge such as T-shape cantilever structure, hanging
beams, corbels, external tendons, anchor beams, sticking steel plate,
and piers. The results of inspection show that the overall state of the
bridge structural member after repair and strengthening is good. The
results of rebound test of concrete strength show that the average
strength of concrete is 46.31Mpa. Whereas, the average value of
concrete strength of anchor beam is 49.82Mpa. According to the
results of static load test, the experimental values are less than
theoretical values of internal forces, deflection, and strain, indicating
that the stiffness of the experimental structure, overall deformation
and integrity satisfy the designed standard and the working
performance is good, and the undertaking capacity has a certain
surplus. There is not visible change in the length and width of cracks
and there are not new cracks under experimental load.
Abstract: Using finite element method (FEM), the elastic
new strain-concentration factor (SNCF) of cylindrical bars
with circumferential flat-bottom groove is studied. This new
SNCF has been defined under triaxial stress state. The
employed specimens have constant groove depth with net
section and gross diameters of 10.0 and 16.7 mm,
respectively. The length of flatness ao has been varied form
0.0 ~12.5 mm to study the elastic SNCF of this type of
geometrical irregularities. The results that the elastic new
SNCF rapidly drops from its elastic value of the groove with
ao = 0.0, i.e. circumferential U-notch, and reaches minimum
value at ao = 2 mm. After that the elastic new SNCF becomes
nearly constant with increasing flatness length (ao). The value
of tensile load at yielding at the groove root increases with
increasing ao. The current results show that severity of the
notch decreases with increasing flatness length ao.
Abstract: Comparison of two approaches for the simulation of
the dynamic behaviour of a permanent magnet linear actuator is
presented. These are full coupled model, where the electromagnetic
field, electric circuit and mechanical motion problems are solved
simultaneously, and decoupled model, where first a set of static
magnetic filed analysis is carried out and then the electric circuit and
mechanical motion equations are solved employing bi-cubic spline
approximations of the field analysis results. The results show that the
proposed decoupled model is of satisfactory accuracy and gives more
flexibility when the actuator response is required to be estimated for
different external conditions, e.g. external circuit parameters or
mechanical loads.
Abstract: Skin color based tracking techniques often assume a
static skin color model obtained either from an offline set of library
images or the first few frames of a video stream. These models
can show a weak performance in presence of changing lighting or
imaging conditions. We propose an adaptive skin color model based
on the Gaussian mixture model to handle the changing conditions.
Initial estimation of the number and weights of skin color clusters
are obtained using a modified form of the general Expectation
maximization algorithm, The model adapts to changes in imaging
conditions and refines the model parameters dynamically using spatial
and temporal constraints. Experimental results show that the method
can be used in effectively tracking of hand and face regions.
Abstract: In this paper, a new method of information fusion – DSmT (Dezert and Smarandache Theory) is introduced to apply to managing and dealing with the uncertain information from robot map building. Here we build grid map form sonar sensors and laser range finder (LRF). The uncertainty mainly comes from sonar sensors and LRF. Aiming to the uncertainty in static environment, we propose Classic DSm (DSmC) model for sonar sensors and laser range finder, and construct the general basic belief assignment function (gbbaf) respectively. Generally speaking, the evidence sources are unreliable in physical system, so we must consider the discounting theory before we apply DSmT. At last, Pioneer II mobile robot serves as a simulation experimental platform. We build 3D grid map of belief layout, then mainly compare the effect of building map using DSmT and DST. Through this simulation experiment, it proves that DSmT is very successful and valid, especially in dealing with highly conflicting information. In short, this study not only finds a new method for building map under static environment, but also supplies with a theory foundation for us to further apply Hybrid DSmT (DSmH) to dynamic unknown environment and multi-robots- building map together.
Abstract: Physical and mechanical properties of Russian olive
fruits were measured at moisture content of 14.43% w.b. The results
revealed that the mean length, width and thickness of Russian olive
fruits were 20.72, 15.73 and 14.69mm, respectively. Mean mass and
volume of Russian olive fruits were measured as 1.45 g and 2.55 cm3,
respectively. The sphericity, aspect ratio and surface area were
calculated as 0.81, 0.72 and 8.96 cm2, respectively, while arithmetic
mean diameter, geometric mean diameter and equivalent diameter of
Russian olive fruits were 17.05, 16.83 and 16.84 mm, respectively.
Whole fruit density, bulk density and porosity of jujube fruits were
measured and found to be 1.01 g/cm3, 0.29 g/cm3 and 69.5%,
respectively. The values of static coefficient of friction on three
surfaces of glass, galvanized iron and plywood were 0.35, 0.36 and
0.43, respectively. The skin color (L*, a*, b*) varied from 9.92 to
16.08; 2.04 to 3.91 and 1.12 to 3.83, respectively. The values of
rupture force, deformation, energy absorbed and hardness were found
to be between 12.14-16.85 N, 2.16-4.25 mm, 3.42-6.99 N mm and
17.1-23.85 N/mm.
Abstract: This paper presents a method of model selection and
identification of Hammerstein systems by hybridization of the genetic
algorithm (GA) and particle swarm optimization (PSO). An unknown
nonlinear static part to be estimated is approximately represented
by an automatic choosing function (ACF) model. The weighting
parameters of the ACF and the system parameters of the linear
dynamic part are estimated by the linear least-squares method. On
the other hand, the adjusting parameters of the ACF model structure
are properly selected by the hybrid algorithm of the GA and PSO,
where the Akaike information criterion is utilized as the evaluation
value function. Simulation results are shown to demonstrate the
effectiveness of the proposed hybrid algorithm.
Abstract: Due to the mobility of users, many information
systems are now developed with the capability of supporting retrieval
of information from both static and mobile users. Hence, the
amount, content and format of the information retrieved will need to
be tailored according to the device and the user who requested for it.
Thus, this paper presents a framework for the design and
implementation of such a system, which is to be developed for
communicating final examination related information to the
academic community at one university in Malaysia. The concept of
personalization will be implemented in the system so that only highly
relevant information will be delivered to the users. The
personalization concept used will be based on user profiling as well
as context. The system in its final state will be accessible through cell
phones as well as intranet connected personal computers.
Abstract: Fake finger submission attack is a major problem in fingerprint recognition systems. In this paper, we introduce an aliveness detection method based on multiple static features, which derived from a single fingerprint image. The static features are comprised of individual pore spacing, residual noise and several first order statistics. Specifically, correlation filter is adopted to address individual pore spacing. The multiple static features are useful to reflect the physiological and statistical characteristics of live and fake fingerprint. The classification can be made by calculating the liveness scores from each feature and fusing the scores through a classifier. In our dataset, we compare nine classifiers and the best classification rate at 85% is attained by using a Reduced Multivariate Polynomial classifier. Our approach is faster and more convenient for aliveness check for field applications.
Abstract: The paper presents the brief information on particular results of experimental study focused to the problems of behavior of structural plated components made of fiber-cement-based materials and used in building constructions, exposed to atmospheric physical effects given by the weather changes in the summer period. Weather changes represented namely by temperature and rain cause also the changes of the temperature and moisture of the investigated structural components. This can affect their static behavior that means stresses and deformations, which have been monitored as the main outputs of tests performed. Experimental verification is based on the simulation of the influence of temperature and rain using the defined procedure of warming and water sprinkling with respect to the corresponding weather conditions during summer period in the South Moravian region at the Czech Republic, for which the application of these structural components is mainly planned. Two types of components have been tested: (i) glass-fiber-concrete panels used for building façades and (ii) fiber-cement slabs used mainly for claddings, but also as a part of floor structures or lost shuttering, and so on.