Abstract: Selected Mapping (SLM) is a PAPR reduction technique, which converts the OFDM signal into several independent signals by multiplication with the phase sequence set and transmits one of the signals with lowest PAPR. But it requires the index of the selected signal i.e. side information (SI) to be transmitted with each OFDM symbol. The PAPR reduction capability of the SLM scheme depends on the selection of phase sequence set. In this paper, we have proposed a new phase sequence set generation scheme based on M-ary chaotic sequence and a mapping scheme to map quaternary data to concentric circle constellation (CCC) is used. It is shown that this method does not require SI and provides better SER performance with good PAPR reduction capability as compared to existing SLMOFDM methods.
Abstract: Multicarrier transmission system such as Orthogonal
Frequency Division Multiplexing (OFDM) is a promising technique
for high bit rate transmission in wireless communication system.
OFDM is a spectrally efficient modulation technique that can achieve
high speed data transmission over multipath fading channels without
the need for powerful equalization techniques. However the price
paid for this high spectral efficiency and less intensive equalization
is low power efficiency. OFDM signals are very sensitive to nonlinear
effects due to the high Peak-to-Average Power Ratio (PAPR),
which leads to the power inefficiency in the RF section of the
transmitter. This paper investigates the effect of PAPR reduction on
the performance parameter of multicarrier communication system.
Performance parameters considered are power consumption of Power
Amplifier (PA) and Digital-to-Analog Converter (DAC), power amplifier
efficiency, SNR of DAC and BER performance of the system.
From our analysis it is found that irrespective of PAPR reduction
technique being employed, the power consumption of PA and DAC
reduces and power amplifier efficiency increases due to reduction in
PAPR. Moreover, it has been shown that for a given BER performance
the requirement of Input-Backoff (IBO) reduces with reduction in
PAPR.
Abstract: This paper investigates the performance of Multiple- Input Multiple-Output (MIMO) feedback system combined with Orthogonal Frequency Division Multiplexing (OFDM). Two types of codebook based channel feedback techniques are used in this work. The first feedback technique uses a combination of both the long-term and short-term channel state information (CSI) at the transmitter, whereas the second technique uses only the short term CSI. The long-term and short-term CSI at the transmitter is used for efficient channel utilization. OFDM is a powerful technique employed in communication systems suffering from frequency selectivity. Combined with multiple antennas at the transmitter and receiver, OFDM proves to be robust against delay spread. Moreover, it leads to significant data rates with improved bit error performance over links having only a single antenna at both the transmitter and receiver. The effectiveness of these techniques has been demonstrated through the simulation of a MIMO-OFDM feedback system. The results have been evaluated for 4x4 MIMO channels. Simulation results indicate the benefits of the MIMO-OFDM channel feedback system over the one without incorporating OFDM. Performance gain of about 3 dB is observed for MIMO-OFDM feedback system as compared to the one without employing OFDM. Hence MIMO-OFDM becomes an attractive approach for future high speed wireless communication systems.
Abstract: Integrated fiber-wireless (FiWi) access networks are a viable solution that can deliver the high profile quadruple play services. Passive optical networks (PON) networks integrated with wireless access networks provide ubiquitous characteristics for high bandwidth applications. Operation of PON improves by employing a variety of multiplexing techniques. One of it is time division/wavelength division multiplexed (TDM/WDM) architecture that improves the performance of optical-wireless access networks. This paper proposes a novel feedback-based TDM/WDM-PON architecture and introduces a model of integrated PON-FiWi networks. Feedback-based link architecture is an efficient solution to improves the performance of optical-line-terminal (OLT) and interlink optical-network-units (ONUs) communication. Furthermore, the feedback-based WDM/TDM-PON architecture is compared with existing architectures in terms of capacity of network throughput.
Abstract: In this paper, we evaluate the performance of the
Hybrid-MIMO Receiver Scheme (HMRS) in Cognitive Radio
network (CR-network). We investigate the efficiency of the proposed
scheme which the energy level and user number of primary user are
varied according to the characteristic of CR-network. HMRS can
allow users to transmit either Space-Time Block Code (STBC) or
Spatial-Multiplexing (SM) streams simultaneously by using
Successive Interference Cancellation (SIC) and Maximum Likelihood
Detection (MLD). From simulation, the results indicate that the
interference level effects to the performance of HMRS. Moreover,
the exact closed-form capacity of the proposed scheme is derived and
compared with STBC scheme.
Abstract: This report aims to utilize existing and future Multiple-Input Multiple-Output Orthogonal Frequency Division Multiplexing Wireless Local Area Network (MIMO-OFDM WLAN) systems characteristics–such as multiple subcarriers, multiple antennas, and channel estimation characteristics–for indoor location estimation systems based on the Direction of Arrival (DOA) and Radio Signal Strength Indication (RSSI) methods. Hybrid of DOA-RSSI methods also evaluated. In the experimental data result, we show that location estimation accuracy performances can be increased by minimizing the multipath fading effect. This is done using multiple subcarrier frequencies over wideband frequencies to estimate one location. The proposed methods are analyzed in both a wide indoor environment and a typical room-sized office. In the experiments, WLAN terminal locations are estimated by measuring multiple subcarriers from arrays of three dipole antennas of access points (AP). This research demonstrates highly accurate, robust and hardware-free add-on software for indoor location estimations based on a MIMO-OFDM WLAN system.
Abstract: This paper describes the gain and noise performances
of discrete Raman amplifier as a function of fiber lengths and the
signal input powers for different pump configurations. Simulation has
been done by using optisystem 7.0 software simulation at signal
wavelength of 1550 nm and a pump wavelength of 1450nm. The
results showed that the gain is higher in bidirectional pumping than in
counter pumping, the gain changes with increasing the fiber length
while the noise figure remain the same for short fiber lengths and the
gain saturates differently for different pumping configuration at
different fiber lengths and power levels of the signal.
Abstract: Stochastic modeling of network traffic is an area of
significant research activity for current and future broadband
communication networks. Multimedia traffic is statistically
characterized by a bursty variable bit rate (VBR) profile. In this
paper, we develop an improved model for uniform activity level
video sources in ATM using a doubly stochastic autoregressive
model driven by an underlying spatial point process. We then
examine a number of burstiness metrics such as the peak-to-average
ratio (PAR), the temporal autocovariance function (ACF) and the
traffic measurements histogram. We found that the former measure is
most suitable for capturing the burstiness of single scene video
traffic. In the last phase of this work, we analyse statistical
multiplexing of several constant scene video sources. This proved,
expectedly, to be advantageous with respect to reducing the
burstiness of the traffic, as long as the sources are statistically
independent. We observed that the burstiness was rapidly
diminishing, with the largest gain occuring when only around 5
sources are multiplexed. The novel model used in this paper for
characterizing uniform activity video was thus found to be an
accurate model.
Abstract: This paper presents a new algorithm for the channel estimation of the OFDM system based on a pilot signal for the new generation of high data rate communication systems. In orthogonal frequency division multiplexing (OFDM) systems over fast-varying fading channels, channel estimation and tracking is generally carried out by transmitting known pilot symbols in given positions of the frequency-time grid. In this paper, we propose to derive an improved algorithm based on the calculation of the mean and the variance of the adjacent pilot signals for a specific distribution of the pilot signals in the OFDM frequency-time grid then calculating of the entire unknown channel coefficients from the equation of the mean and the variance. Simulation results shows that the performance of the OFDM system increase as the length of the channel increase where the accuracy of the estimated channel will be increased using this low complexity algorithm, also the number of the pilot signal needed to be inserted in the OFDM signal will be reduced which lead to increase in the throughput of the signal over the OFDM system in compared with other type of the distribution such as Comb type and Block type channel estimation.
Abstract: A hardware efficient, multi mode, re-configurable
architecture of interleaver/de-interleaver for multiple standards,
like DVB, WiMAX and WLAN is presented. The interleavers
consume a large part of silicon area when implemented by using
conventional methods as they use memories to store permutation
patterns. In addition, different types of interleavers in different
standards cannot share the hardware due to different construction
methodologies. The novelty of the work presented in this paper is
threefold: 1) Mapping of vital types of interleavers including
convolutional interleaver onto a single architecture with flexibility
to change interleaver size; 2) Hardware complexity for channel
interleaving in WiMAX is reduced by using 2-D realization of the
interleaver functions; and 3) Silicon cost overheads reduced by
avoiding the use of small memories. The proposed architecture
consumes 0.18mm2 silicon area for 0.12μm process and can
operate at a frequency of 140 MHz. The reduced complexity helps
in minimizing the memory utilization, and at the same time
provides strong support to on-the-fly computation of permutation
patterns.
Abstract: In an Orthogonal Frequency Division Multiplexing (OFDM) systems, the Peak to Average power Ratio (PAR) is high. The clipping signal scheme is a useful and simple method to reduce the PAR. However, it introduces additional noise that degrades the systems performance. We propose an oversampling scheme to deal with the received signal in order to reduce the clipping noise by using Finite Impulse Response (FIR) filter. Coefficients of filter are obtained by correlation function of the received signal and the oversampling information at receiver. The performance of the proposed technique is evaluated for frequency selective channel. Results show that the proposed scheme can mitigate the clipping noise significantly for OFDM systems and in order to maintain the system's capacity, the clipping ratio should be larger than 2.5.
Abstract: The modern telecommunication industry demands
higher capacity networks with high data rate. Orthogonal frequency
division multiplexing (OFDM) is a promising technique for high data
rate wireless communications at reasonable complexity in wireless
channels. OFDM has been adopted for many types of wireless
systems like wireless local area networks such as IEEE 802.11a, and
digital audio/video broadcasting (DAB/DVB). The proposed research
focuses on a concatenated coding scheme that improve the
performance of OFDM based wireless communications. It uses a
Redundant Residue Number System (RRNS) code as the outer code
and a convolutional code as the inner code. Here, a direct conversion
of analog signal to residue domain is done to reduce the conversion
complexity using sigma-delta based parallel analog-to-residue
converter. The bit error rate (BER) performances of the proposed
system under different channel conditions are investigated. These
include the effect of additive white Gaussian noise (AWGN),
multipath delay spread, peak power clipping and frame start
synchronization error. The simulation results show that the proposed
RRNS-Convolutional concatenated coding (RCCC) scheme provides
significant improvement in the system performance by exploiting the
inherent properties of RRNS.
Abstract: In this paper, we have proposed two novel plasmonic demultiplexing structures based on metal-insulator-metal surfaces which, beside their compact size, have a very good transmission spectrum. The impact of the key internal parameters on the transmission spectrum is numerically analyzed by using the twodimensional (2D) finite difference time domain (FDTD) method. The proposed structures could be used to develop ultra-compact photonic wavelength demultiplexing devices for large-scale photonic integration.
Abstract: Space Vector Modulation (SVM) is an optimum Pulse Width Modulation (PWM) technique for an inverter used in a variable frequency drive applications. It is computationally rigorous and hence limits the inverter switching frequency. Increase in switching frequency can be achieved using Neural Network (NN) based SVM, implemented on application specific chips. This paper proposes a neural network based SVM technique for a Voltage Source Inverter (VSI). The network proposed is independent of switching frequency. Different architectures are investigated keeping the total number of neurons constant. The performance of the inverter is compared for various switching frequencies for different architectures of NN based SVM. From the results obtained, the network with minimum resource and appropriate word length is identified. The bit precision required for this application is identified. The network with 8-bit precision is implemented in the IC XCV 400 and the results are presented. The performance of NN based general purpose SVM with higher bit precision is discussed.
Abstract: Internet infrastructures in most places of the world
have been supported by the advancement of optical fiber technology,
most notably wavelength division multiplexing (WDM) system.
Optical technology by means of WDM system has revolutionized
long distance data transport and has resulted in high data capacity,
cost reductions, extremely low bit error rate, and operational
simplification of the overall Internet infrastructure. This paper
analyses and compares the system impairments, which occur at data
transmission rates of 2.5Gb/s and 10 Gb/s per wavelength channel in
our proposed optical WDM system for Internet infrastructure in
Tanzania. The results show that the data transmission rate of 2.5 Gb/s
has minimum system impairments compared with a rate of 10 Gb/s
per wavelength channel, and achieves a sufficient system
performance to provide a good Internet access service.
Abstract: SDMA (Space-Division Multiple Access) is a MIMO
(Multiple-Input and Multiple-Output) based wireless communication
network architecture which has the potential to significantly increase
the spectral efficiency and the system performance. The maximum
likelihood (ML) detection provides the optimal performance, but its
complexity increases exponentially with the constellation size of
modulation and number of users. The QR decomposition (QRD)
MUD can be a substitute to ML detection due its low complexity and
near optimal performance. The minimum mean-squared-error
(MMSE) multiuser detection (MUD) minimises the mean square
error (MSE), which may not give guarantee that the BER of the
system is also minimum. But the minimum bit error rate (MBER)
MUD performs better than the classic MMSE MUD in term of
minimum probability of error by directly minimising the BER cost
function. Also the MBER MUD is able to support more users than
the number of receiving antennas, whereas the rest of MUDs fail in
this scenario. In this paper the performance of various MUD
techniques is verified for the correlated MIMO channel models based
on IEEE 802.16n standard.
Abstract: New generation mobile communication networks have
the ability of supporting triple play. In order that, Orthogonal
Frequency Division Multiplexing (OFDM) access techniques have
been chosen to enlarge the system ability for high data rates
networks. Many of cross-layer modeling and optimization schemes
for Quality of Service (QoS) and capacity of downlink multiuser
OFDM system were proposed. In this paper, the Maximum Weighted
Capacity (MWC) based resource allocation at the Physical (PHY)
layer is used. This resource allocation scheme provides a much better
QoS than the previous resource allocation schemes, while
maintaining the highest or nearly highest capacity and costing similar
complexity. In addition, the Delay Satisfaction (DS) scheduling at the
Medium Access Control (MAC) layer, which allows more than one
connection to be served in each slot is used. This scheduling
technique is more efficient than conventional scheduling to
investigate both of the number of users as well as the number of
subcarriers against system capacity. The system will be optimized for
different operational environments: the outdoor deployment scenarios
as well as the indoor deployment scenarios are investigated and also
for different channel models. In addition, effective capacity approach
[1] is used not only for providing QoS for different mobile users, but
also to increase the total wireless network's throughput.
Abstract: Reconfigurable optical add/drop multiplexers
(ROADMs) can be classified into three categories based on their
underlying switching technologies. Category I consists of a single
large optical switch; category II is composed of a number of small
optical switches aligned in parallel; and category III has a single
optical switch and only one wavelength being added/dropped. In this
paper, to evaluate the wavelength-routing capability of ROADMs of
category-II in dynamic optical networks,the dynamic traffic models
are designed based on Bernoulli, Poisson distributions for smooth
and regular types of traffic. Through Analytical and Simulation
results, the routing power of cat-II of ROADM networks for two
traffic models are determined.
Abstract: In this paper, we propose a novel frequency offset
estimation scheme for orthogonal frequency division multiplexing
(OFDM) systems. By correlating the OFDM signals within the coherence
phase bandwidth and employing a threshold in the frequency
offset estimation process, the proposed scheme is not only robust to
the timing offset but also has a reduced complexity compared with
that of the conventional scheme. Moreover, a timing offset estimation
scheme is also proposed as the next stage of the proposed frequency
offset estimation. Numerical results show that the proposed scheme
can estimate frequency offset with lower computational complexity
and does not require additional memory while maintaining the same
level of estimation performance.
Abstract: For broadband wireless mobile communication
systems the orthogonal frequency division multiplexing (OFDM) is a
suitable modulation scheme. The frequency offset between
transmitter and receiver local oscillator is main drawback of OFDM
systems, which causes intercarrier interference (ICI) in the
subcarriers of the OFDM system. This ICI degrades the bit error rate
(BER) performance of the system. In this paper an improved self-ICI
cancellation scheme is proposed to improve the system performance.
The proposed scheme is based on discrete Fourier transform-inverse
discrete Fourier transform (DFT-IDFT). The simulation results show
that there is satisfactory improvement in the bit error rate (BER)
performance of the present scheme.