Abstract: In this paper, a novel fuzzy approach is developed
while solving the Dynamic Routing and Wavelength Assignment
(DRWA) problem in optical networks with Wavelength Division
Multiplexing (WDM). In this work, the effect of nonlinear and linear
impairments such as Four Wave Mixing (FWM) and amplifier
spontaneous emission (ASE) noise are incorporated respectively. The
novel algorithm incorporates fuzzy logic controller (FLC) to reduce
the effect of FWM noise and ASE noise on a requested lightpath
referred in this work as FWM aware fuzzy dynamic routing and
wavelength assignment algorithm. The FWM crosstalk products and
the static FWM noise power per link are pre computed in order to
reduce the set up time of a requested lightpath, and stored in an
offline database. These are retrieved during the setting up of a
lightpath and evaluated online taking the dynamic parameters like
cost of the links into consideration.
Abstract: Multiple Input Multiple Output (MIMO) systems are
wireless systems with multiple antenna elements at both ends of the
link. Wireless communication systems demand high data rate and
spectral efficiency with increased reliability. MIMO systems have
been popular techniques to achieve these goals because increased
data rate is possible through spatial multiplexing scheme and
diversity. Spatial Multiplexing (SM) is used to achieve higher
possible throughput than diversity. In this paper, we propose a Zero-
Forcing (ZF) detection using a combination of Ordered Successive
Interference Cancellation (OSIC) and Zero Forcing using
Interference Cancellation (ZF-IC). The proposed method used an
OSIC based on Signal to Noise Ratio (SNR) ordering to get the
estimation of last symbol, then the estimated last symbol is
considered to be an input to the ZF-IC. We analyze the Bit Error Rate
(BER) performance of the proposed MIMO system over Rayleigh
Fading Channel, using Binary Phase Shift Keying (BPSK)
modulation scheme. The results show better performance than the
previous methods.
Abstract: The Orthogonal Frequency Division Multiplexing
(OFDM) with high data rate, high spectral efficiency and its ability to
mitigate the effects of multipath makes them most suitable in wireless
application. Impulsive noise distorts the OFDM transmission and
therefore methods must be investigated to suppress this noise. In this
paper, a State Space Recursive Least Square (SSRLS) algorithm
based adaptive impulsive noise suppressor for OFDM
communication system is proposed. And a comparison with another
adaptive algorithm is conducted. The state space model-dependent
recursive parameters of proposed scheme enables to achieve steady
state mean squared error (MSE), low bit error rate (BER), and faster
convergence than that of some of existing algorithm.
Abstract: We propose new multiple-channel piezoelectric (PZT)
actuated tunable optical filter based on racetrack multi-ring
resonators for wavelength de-multiplexing network applications. We
design tunable eight-channel wavelength de-multiplexer consisting of
eight cascaded PZT actuated tunable multi-ring resonator filter with a
channel spacing of 1.6nm. The filter for each channel is basically
structured on a suspended beam, sandwiched with piezoelectric
material and built in integrated ring resonators which are placed on
the middle of the beam to gain uniform stress and linearly varying
longitudinal strain. A reference single mode serially coupled multi
stage racetrack ring resonator with the same radii and coupling length
is designed with a line width of 0.8974nm with a flat top pass band at
1dB of 0.5205nm and free spectral range of about 14.9nm. In each
channel, a small change in the perimeter of the rings is introduced to
establish the shift in resonance wavelength as per the defined channel
spacing. As a result, when a DC voltage is applied, the beams will
elongate, which involves mechanical deformation of the ring
resonators that induces a stress and a strain, which brings a change in
refractive index and perimeter of the rings leading to change in the
output spectrum shift providing the tunability of central wavelength
in each channel. Simultaneous wave length shift as high as
45.54pm/
Abstract: Wavelength Division Multiplexing (WDM) is the dominant transport technology used in numerous high capacity backbone networks, based on optical infrastructures. Given the importance of costs (CapEx and OpEx) associated to these networks, resource management is becoming increasingly important, especially how the optical circuits, called “lightpaths”, are routed throughout the network. This requires the use of efficient algorithms which provide routing strategies with the lowest cost. We focus on the lightpath routing and wavelength assignment problem, known as the RWA problem, while optimizing wavelength fragmentation over the network. Wavelength fragmentation poses a serious challenge for network operators since it leads to the misuse of the wavelength spectrum, and then to the refusal of new lightpath requests. In this paper, we first establish a new Integer Linear Program (ILP) for the problem based on a node-link formulation. This formulation is based on a multilayer approach where the original network is decomposed into several network layers, each corresponding to a wavelength. Furthermore, we propose an efficient heuristic for the problem based on a greedy algorithm followed by a post-treatment procedure. The obtained results show that the optimal solution is often reached. We also compare our results with those of other RWA heuristic methods
Abstract: We address a new integer frequency offset (IFO)
estimation scheme with an aid of a pilot for orthogonal frequency
division multiplexing systems. After correlating each continual pilot
with a predetermined scattered pilot, the correlation value is again
correlated to alleviate the influence of the timing offset. From
numerical results, it is demonstrated that the influence of the timing
offset on the IFO estimation is significantly decreased.
Abstract: This paper presents system level CMOS solid-state
nanopore techniques enhancement for speedup next generation
molecular recording and high throughput channels. This discussion
also considers optimum number of base-pair (bp) measurements
through channel as an important role to enhance potential read
accuracy. Effective power consumption estimation offered suitable
range of multi-channel configuration. Nanopore bp extraction model
in statistical method could contribute higher read accuracy with
longer read-length (200 < read-length). Nanopore ionic current
switching with Time Multiplexing (TM) based multichannel readout
system contributed hardware savings.
Abstract: In this paper, we investigate the effect of friendly
jamming power allocation strategies on the achievable average
secrecy rate over a bank of parallel fading wiretap channels.
We investigate the achievable average secrecy rate in parallel
fading wiretap channels subject to Rayleigh and Rician fading.
The achievable average secrecy rate, due to the presence of a
line-of-sight component in the jammer channel is also evaluated.
Moreover, we study the detrimental effect of correlation across the
parallel sub-channels, and evaluate the corresponding decrease in the
achievable average secrecy rate for the various fading configurations.
We also investigate the tradeoff between the transmission power
and the jamming power for a fixed total power budget. Our
results, which are applicable to current orthogonal frequency division
multiplexing (OFDM) communications systems, shed further light on
the achievable average secrecy rates over a bank of parallel fading
channels in the presence of friendly jammers.
Abstract: We address the integer frequency offset (IFO)
estimation under the influence of the timing offset (TO) in orthogonal
frequency division multiplexing (OFDM) systems. Incorporating the
IFO and TO into the symbol set used to represent the received
OFDM symbol, we investigate the influence of the TO on the IFO,
and then, propose a combining method between two consecutive
OFDM correlations, reducing the influence. The proposed scheme
has almost the same complexity as that of the conventional
schemes, whereas it does not need the TO knowledge contrary to
the conventional schemes. From numerical results it is confirmed
that the proposed scheme is insensitive to the TO, consequently,
yielding an improvement of the IFO estimation performance over
the conventional schemes when the TO exists.
Abstract: High Peak to Average Power Ratio (PAPR) of the
transmitted signal is a serious problem in multicarrier systems (MC),
such as Orthogonal Frequency Division Multiplexing (OFDM), or in
Multi-Carrier Code Division Multiple Access (MC-CDMA) systems,
due to large number of subcarriers. This effect is possible reduce with
some PAPR reduction techniques. Spreading sequences at the
presence of Saleh and Rapp models of high power amplifier (HPA)
have big influence on the behavior of system. In this paper we
investigate the bit-error-rate (BER) performance of MC-CDMA
systems. Basically we can see from simulations that the MC-CDMA
system with Iterative algorithm can be providing significantly better
results than the MC-CDMA system. The results of our analyses are
verified via simulation.
Abstract: The idea of the asynchronous transmission in
wavelength division multiplexing (WDM) ring MANs is studied in
this paper. Especially, we present an efficient access technique to
coordinate the collisions-free transmission of the variable sizes of IP
traffic in WDM ring core networks. Each node is equipped with a
tunable transmitter and a tunable receiver. In this way, all the
wavelengths are exploited for both transmission and reception. In
order to evaluate the performance measures of average throughput,
queuing delay and packet dropping probability at the buffers, a
simulation model that assumes symmetric access rights among the
nodes is developed based on Poisson statistics. Extensive numerical
results show that the proposed protocol achieves apart from high
bandwidth exploitation for a wide range of offered load, fairness of
queuing delay and dropping events among the different packets size
categories.
Abstract: This paper proposes frequency offset (FO) estimation
schemes robust to the non-Gaussian noise for orthogonal frequency
division multiplexing (OFDM) systems. A maximum-likelihood (ML)
scheme and a low-complexity estimation scheme are proposed by
applying the probability density function of the cyclic prefix of
OFDM symbols to the ML criterion. From simulation results, it is
confirmed that the proposed schemes offer a significant FO estimation
performance improvement over the conventional estimation scheme
in non-Gaussian noise environments.
Abstract: ICT services are a key element of communications and important for socio-economic development. In recognition of the importance of this, the Tanzanian Government started to implement a National ICT Broadband Infrastructure Fibre Optic Backbone (NICTBB) in 2009; this development was planned to be implemented in four phases using an optical dense wavelength division multiplexing (DWDM) network technology in collaboration with the Chinese Government through the Chinese International Telecommunications Construction Corporation (CITCC) under a bilateral agreement. This paper briefly explores the NICTBB network technologies implementation, operations and Internet bandwidth costs. It also provides an in depth assessment of the delivery of ICT services such as e-services and m-services in both urban and rural areas following commissioning of the NICTBB system. Following quantitative and qualitative approaches, the study shows that there have been significant improvements in utilization efficiency, effectiveness and the reliability of the ICT service such as e-services and m-services the NICTCBB was commissioned.
Abstract: Performance of Orthogonal Frequency Division Multiplexing (OFDM) system can be improved by adding channel coding (error correction code) to detect and correct errors that occur during data transmission. One can use the convolution code. This paper present performance of OFDM using Space Time Block Codes (STBC) diversity technique use QAM modulation with code rate ½. The evaluation is done by analyzing the value of Bit Error Rate (BER) vs. Energy per Bit to Noise Power Spectral Density Ratio (Eb/No). This scheme is conducted 256 subcarrier transmits Rayleigh multipath channel in OFDM system. To achieve a BER of 10-3 is required 10dB SNR in SISO-OFDM scheme. For 2x2 MIMO-OFDM scheme requires 10 dB to achieve a BER of 10-3. For 4x4 MIMO-OFDM scheme requires 5 dB while adding convolution in a 4x4 MIMO-OFDM can improve performance up to 0 dB to achieve the same BER. This proves the existence of saving power by 3 dB of 4x4 MIMO-OFDM system without coding, power saving 7dB of 2x2 MIMO-OFDM and significant power savings from SISO-OFDM system
Abstract: Wavelet analysis has some strong advantages over Fourier analysis, as it allows a time-frequency domain analysis, allowing optimal resolution and flexibility. As a result, they have been satisfactorily applied in almost all the fields of communication systems including OFDM which is a strong candidate for next generation of wireless technology. In this paper, the performances of wavelet based Multiuser Multiple Input and Multiple Output Orthogonal Frequency Division Multiplexing (MU-MIMO OFDM) systems are analyzed in terms of BER. It has been shown that the wavelet based systems outperform the classical FFT based systems. This analysis also unfolds an interesting result, where wavelet based OFDM system will have a constant error performance using Regularized Channel Inversion (RCI) beamforming for any number of users, and outperforms in all possible scenario in a multiuser environment. An extensive computer simulations show that a PAPR reduction of up to 6.8dB can be obtained with M=64.
Abstract: OFDM systems are known to have a high PAPR (Peak-to-Average Power Ratio) compared with single-carrier systems. In fact, the high PAPR is one of the most detrimental aspects in the OFDM system, as it can cause power degradation (Inband distortion) and spectral spreading (Out-of-band radiation). In this paper, from the foundation of the PAPR analysis an effective method of PAPR reduction has been proposed based on Orthogonal Eigenvector Matrix (OEM) transform. Extensive computer simulations show that a PAPR reduction of up to 4.4 dB can be obtained without introducing in-band distortion or out-of-band radiation in the system.
Abstract: In mobile communication systems, performance and capacity are affected by multi-path fading, delay spread and Co-Channel Interference (CCI). For this reason Orthogonal Frequency Division Multiplexing (OFDM) and adaptive antenna array are used is required. The goal of the OFDM is to improve the system performance against Inter-Symbol Interference (ISI). An array of adaptive antennas has been employed to suppress CCI by spatial technique. To suppress CCI in OFDM systems two main schemes the pre-FFT and the post-FFT have been proposed. In this paper, through a system level simulation, the behavior of the pre-FFT and post-FFT beamformers for OFDM system has been investigated based on two algorithms namely, Least Mean Squares (LMS) and Recursive Least Squares (RLS). The performance of the system is also discussed in multipath fading channel system specified by 3GPP Long Term Evolution (LTE).
Abstract: The performance of the Optical Code Division Multiplexing/ Wavelength Division Multiplexing (WDM/OCDM) technique for Optical Packet Switch is investigated. The impact on the performance of the impairment due to both Multiple Access Interference and Beat noise is studied. The Packet Loss Probability due to output packet contentions is evaluated as a function of the main switch and traffic parameters when Gold coherent optical codes are adopted. The Packet Loss Probability of the OCDM/WDM switch can reach 10-9 when M=16 wavelengths, Gold code of length L=511 and only 24 wavelength converters are used in the switch.
Abstract: In this paper, we study statistical multiplexing of VBR
video in ATM networks. ATM promises to provide high speed realtime
multi-point to central video transmission for telemedicine
applications in rural hospitals and in emergency medical services.
Video coders are known to produce variable bit rate (VBR) signals
and the effects of aggregating these VBR signals need to be
determined in order to design a telemedicine network infrastructure
capable of carrying these signals. We first model the VBR video
signal and simulate it using a generic continuous-data autoregressive
(AR) scheme. We carry out the queueing analysis by the Fluid
Approximation Model (FAM) and the Markov Modulated Poisson
Process (MMPP). The study has shown a trade off: multiplexing
VBR signals reduces burstiness and improves resource utilization,
however, the buffer size needs to be increased with an associated
economic cost. We also show that the MMPP model and the Fluid
Approximation model fit best, respectively, the cell region and the
burst region. Therefore, a hybrid MMPP and FAM completely
characterizes the overall performance of the ATM statistical
multiplexer. The ramifications of this technology are clear: speed,
reliability (lower loss rate and jitter), and increased capacity in video
transmission for telemedicine. With migration to full IP-based
networks still a long way to achieving both high speed and high
quality of service, the proposed ATM architecture will remain of
significant use for telemedicine.
Abstract: Power line channel is proposed as an alternative for broadband data transmission especially in developing countries like Tanzania [1]. However the channel is affected by stochastic attenuation and deep notches which can lead to the limitation of channel capacity and achievable data rate. Various studies have characterized the channel without giving exactly the maximum performance and limitation in data transfer rate may be this is due to complexity of channel modeling being used. In this paper the channel performance of medium voltage, low voltage and indoor power line channel is presented. In the investigations orthogonal frequency division multiplexing (OFDM) with phase shift keying (PSK) as carrier modulation schemes is considered, for indoor, medium and low voltage channels with typical ten branches and also Golay coding is applied for medium voltage channel. From channels, frequency response deep notches are observed in various frequencies which can lead to reduce the achievable data rate. However, is observed that data rate up to 240Mbps is realized for a signal to noise ratio of about 50dB for indoor and low voltage channels, however for medium voltage a typical link with ten branches is affected by strong multipath and coding is required for feasible broadband data transfer.