Abstract: Erosion and abrasion are wear mechanisms reducing
the lifetime of machine elements like valves, pump and pipe systems.
Both wear mechanisms are acting at the same time, causing a
“Synergy” effect, which leads to a rapid damage of the surface.
Different parameters are effective on erosive abrasive wear rate. In
this study effect of particle impact angle on wear rate and wear
mechanism of ductile and brittle materials was investigated. A new
slurry pot was designed for experimental investigation. As abrasive
particle, silica sand was used. Particle size was ranking between 200-
500 μm. All tests were carried out in a sand-water mixture of 20%
concentration for four hours. Impact velocities of the particles were
4.76 m/s. As ductile material steel St 37 with Vickers Hardness
Number (VHN) of 245 and quenched St 37 with 510 VHN was used
as brittle material. After wear tests, morphology of the eroded
surfaces were investigated for better understanding of the wear
mechanisms acting at different impact angles by using Scanning
Electron Microscope. The results indicated that wear rate of ductile
material was higher than brittle material. Maximum wear rate was
observed by ductile material at a particle impact angle of 300 and
decreased further by an increase in attack angle. Maximum wear rate
by brittle materials was by impact angle of 450 and decreased further
up to 900. Ploughing was the dominant wear mechanism by ductile
material. Microcracks on the surface were detected by ductile
materials, which are nucleation centers for crater formation. Number
of craters decreased and depth of craters increased by ductile
materials by attack angle higher than 300. Deformation wear
mechanism was observed by brittle materials. Number and depth of
pits decreased by brittle materials by impact angles higher than 450.
At the end it is concluded that wear rate could not be directly related
to impact angle of particles due to the different reaction of ductile and
brittle materials.
Abstract: Graphene was dispersed using a tip sonicator and the
effect of surfactants were analysed. Sodium Dodecyl Sulphate (SDS)
and Polyvinyl Alcohol (PVA) were compared to observe whether or
not they had any effect on any de-wrinkling, and secondly whether
they aided to achieve better dispersions. There is a huge demand for
wrinkle free graphene as this will greatly increase its usefulness in
various engineering applications. A comprehensive literature on dewrinkling
graphene has been discussed. Low magnification Scanning
Electronic Microscopy (SEM) was conducted to assess the quality of
graphene de-wrinkling. The utilization of the PVA has significant
effect on de-wrinkling whereas SDS had minimal effect on the dewrinkling
of graphene.
Abstract: Financial innovations can be regarded as the cause
and the effect of the evolution of the financial system. Most of
financial innovations are created by various financial institutions for
their own purposes and needs. However, due to their diversity,
financial innovations can be also applied by various business entities
(other than financial institutions).
This paper focuses on the potential application of financial
innovations by non-financial companies. It is assumed that financial
innovations may be effectively applied in all fields of corporate
financial decisions integrating financial management with the risk
management process. Appropriate application of financial
innovations may enhance the development of the company and
increase its value by improving its financial situation and reducing
the level of risk. On the other hand, misused financial innovations
may become the source of extra risk for the company threatening its
further operation.
The main objective of the paper is to identify the major types of
financial innovations offered to non-financial companies by the
banking system in Poland. It also aims at identifying the main factors
determining the creation of financial innovations in the banking
system in Poland and indicating future directions of their
development.
This paper consists of conceptual and empirical part. Conceptual
part based on theoretical study is focused on the determinants of the
process of financial innovations and their application by the nonfinancial
companies. Theoretical study is followed by the empirical
research based on the analysis of the actual offer of the 20 biggest
banks operating in Poland with regard to financial innovations
offered to SMEs and large corporations. These innovations are
classified according to the main functions of the integrated financial
management, such as financing, investment, working capital
management and risk management.
Empirical study has proved that the biggest banks operating in the
Polish market offer to their business customers many types and
classes of financial innovations. This offer appears vast and adequate
to the needs and purposes of the Polish non-financial companies. It
was observed that financial innovations pertained to financing
decisions dominate in the banks’ offer. However, due to high
diversification of the offered financial innovations, business
customers may effectively apply them in all fields and areas of
integrated financial management. It should be underlined, that the
banks’ offer is highly dispersed, which may limit the implementation
of financial innovations in the corporate finance. It would be also
recommended for the banks operating in the Polish market to
intensify the education campaign aiming at increasing knowledge
about financial innovations among business customers.
Abstract: Ceramic Waste Aggregates (CWAs) were made from
electric porcelain insulator wastes supplied from an electric power
company, which were crushed and ground to fine aggregate sizes. In
this study, to develop the CWA mortar as an eco–efficient, ground
granulated blast–furnace slag (GGBS) as a Supplementary
Cementitious Material (SCM) was incorporated. The water–to–binder
ratio (W/B) of the CWA mortars was varied at 0.4, 0.5, and 0.6. The
cement of the CWA mortar was replaced by GGBS at 20 and 40% by
volume (at about 18 and 37% by weight). Mechanical properties of
compressive and splitting tensile strengths, and elastic modulus were
evaluated at the age of 7, 28, and 91 days. Moreover, the chloride
ingress test was carried out on the CWA mortars in a 5.0% NaCl
solution for 48 weeks. The chloride diffusion was assessed by using an
electron probe microanalysis (EPMA). To consider the relation of the
apparent chloride diffusion coefficient and the pore size, the pore size
distribution test was also performed using a mercury intrusion
porosimetry at the same time with the EPMA. The compressive
strength of the CWA mortars with the GGBS was higher than that
without the GGBS at the age of 28 and 91 days. The resistance to the
chloride ingress of the CWA mortar was effective in proportion to the
GGBS replacement level.
Abstract: This paper reviews the model-based qualitative and
quantitative Operations Management research in the context of
Construction Supply Chain Management (CSCM). Construction
industry has been traditionally blamed for low productivity, cost and
time overruns, waste, high fragmentation and adversarial
relationships. The construction industry has been slower than other
industries to employ the Supply Chain Management (SCM) concept
and develop models that support the decision-making and planning.
However the last decade there is a distinct shift from a project-based
to a supply-based approach of construction management. CSCM
comes up as a new promising management tool of construction
operations and improves the performance of construction projects in
terms of cost, time and quality. Modeling the Construction Supply
Chain (CSC) offers the means to reap the benefits of SCM, make
informed decisions and gain competitive advantage. Different
modeling approaches and methodologies have been applied in the
multi-disciplinary and heterogeneous research field of CSCM. The
literature review reveals that a considerable percentage of the CSC
modeling research accommodates conceptual or process models
which present general management frameworks and do not relate to
acknowledged soft Operations Research methods. We particularly
focus on the model-based quantitative research and categorize the
CSCM models depending on their scope, objectives, modeling
approach, solution methods and software used. Although over the last
few years there has been clearly an increase of research papers on
quantitative CSC models, we identify that the relevant literature is
very fragmented with limited applications of simulation,
mathematical programming and simulation-based optimization. Most
applications are project-specific or study only parts of the supply
system. Thus, some complex interdependencies within construction
are neglected and the implementation of the integrated supply chain
management is hindered. We conclude this paper by giving future
research directions and emphasizing the need to develop optimization
models for integrated CSCM. We stress that CSC modeling needs a
multi-dimensional, system-wide and long-term perspective. Finally,
prior applications of SCM to other industries have to be taken into
account in order to model CSCs, but not without translating the
generic concepts to the context of construction industry.
Abstract: The rationale behind this study is considering
combating and preventing the phenomenon of trafficking in human
beings from a multidisciplinary perspective that involves many layers
of the society.
Trafficking in human beings is an abhorrent phenomenon highly
affecting negatively the victims and their families in both human and
material aspect, sometimes causing irreversible damages. The longer
term effects of this phenomenon, in countries with a weak economic
development and extremely young and dynamic population, such as
Kosovo, without proper measures to prevented and control can cause
tremendous damages in the society. Given the fact that a complete
eradication of this phenomenon is almost impossible, efforts should
be concentrated at least on the prevention and controlling aspects.
Treating trafficking in human beings based on traditional police
tactics, methods and proceedings cannot bring satisfactory results.
There is no doubt that a multi-disciplinary approach is an
irreplaceable requirement, in other words, a combination of authentic
and functional proactive and reactive methods, techniques and tactics.
Obviously, police must exercise its role in preventing and combating
trafficking in human beings, a role sanctioned by the law, however,
police role and contribution cannot by any means considered
complete if all segments of the society are not included in these
efforts. Naturally, civil society should have an important share in
these collaborative and interactive efforts especially in preventive
activities such as: awareness on trafficking risks and damages,
proactive engagement in drafting appropriate legislation and
strategies, law enforcement monitoring and direct or indirect
involvement in protective and supporting activities which benefit the
victims of trafficking etc.
Abstract: Aim of this work is to determine the theoretical and
experimental properties of filament wound glass fiber/epoxy resin
composite pipes with different winding design subjected under
bending. For determination of bending strength of composite samples
three point bending tests were conducted. Good correlation between
theoretical and experimental results has been obtained, where sample
No4 has shown the highest value of bending strength. All samples
have demonstrated matrix cracking and fiber failure followed by
layers delamination during testing. Also, it was found that smaller
winding angles lead to an increase in bending stress. From presented
results good merger between glass fibers and epoxy resin was
confirmed by SEM analysis.
Abstract: A simple adaptive voice activity detector (VAD) is
implemented using Gabor and gammatone atomic decomposition of
speech for high Gaussian noise environments. Matching pursuit is
used for atomic decomposition, and is shown to achieve optimal
speech detection capability at high data compression rates for low
signal to noise ratios. The most active dictionary elements found by
matching pursuit are used for the signal reconstruction so that the
algorithm adapts to the individual speakers dominant time-frequency
characteristics. Speech has a high peak to average ratio enabling
matching pursuit greedy heuristic of highest inner products to isolate
high energy speech components in high noise environments. Gabor
and gammatone atoms are both investigated with identical
logarithmically spaced center frequencies, and similar bandwidths.
The algorithm performs equally well for both Gabor and gammatone
atoms with no significant statistical differences. The algorithm
achieves 70% accuracy at a 0 dB SNR, 90% accuracy at a 5 dB SNR
and 98% accuracy at a 20dB SNR using 30d B SNR as a reference
for voice activity.
Abstract: A chromium-loaded ash originating from incineration of tannery sludge under anoxic conditions was mixed with low grade soda-lime glass powder coming from commercial glass bottles. The relative weight proportions of ash over glass powder tested were 30/70, 40/60 and 50/50. The solid mixtures, formed in green state compacts, were sintered at the temperature range of 800o C up to 1200o C. The resulting products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDXS) and micro-indentation. The above methods were employed to characterize the various phases, microstructure and hardness of the produced materials. Thermal treatment at 800o C and 1000o C produced opaque ceramic products composed of a variety of chromium-containing and chromium-free crystalline phases. Thermal treatment at 1200o C gave rise to composite products, where only chromium-containing crystalline phases were detected. Hardness results suggest that specific products are serious candidates for structural applications.
Abstract: Moving into a new era of healthcare, new tools and
devices are developed to extend and improve health services, such as
remote patient monitoring and risk prevention. In this concept,
Internet of Things (IoT) and Cloud Computing present great
advantages by providing remote and efficient services, as well as
cooperation between patients, clinicians, researchers and other health
professionals. This paper focuses on patients suffering from bipolar
disorder, a brain disorder that belongs to a group of conditions
called affective disorders, which is characterized by great mood
swings. We exploit the advantages of Semantic Web and Cloud
Technologies to develop a patient monitoring system to support
clinicians. Based on intelligently filtering of evidence-knowledge and
individual-specific information we aim to provide treatment
notifications and recommended function tests at appropriate times or
concluding into alerts for serious mood changes and patient’s nonresponse
to treatment. We propose an architecture as the back-end
part of a cloud platform for IoT, intertwining intelligence devices
with patients’ daily routine and clinicians’ support.
Abstract: This article discusses event monitoring options for
heterogeneous event sources as they are given in nowadays
heterogeneous distributed information systems. It follows the central
assumption, that a fully generic event monitoring solution cannot
provide complete support for event monitoring; instead, event source
specific semantics such as certain event types or support for certain
event monitoring techniques have to be taken into account.
Following from this, the core result of the work presented here is
the extension of a configurable event monitoring (Web) service for a
variety of event sources. A service approach allows us to trade
genericity for the exploitation of source specific characteristics. It
thus delivers results for the areas of SOA, Web services, CEP and
EDA.
Abstract: The problem of toughening in brittle materials
reinforced by fibers is complex, involving all of the mechanical
properties of fibers, matrix and the fiber/matrix interface, as well as
the geometry of the fiber. Development of new numerical methods
appropriate to toughening simulation and analysis is necessary. In
this work, we have performed simulations and analysis of toughening
in brittle matrix reinforced by randomly distributed fibers by means
of the discrete elements method. At first, we put forward a
mechanical model of toughening contributed by random fibers. Then
with a numerical program, we investigated the stress, damage and
bridging force in the composite material when a crack appeared in the
brittle matrix. From the results obtained, we conclude that: (i) fibers
of high strength and low elasticity modulus are beneficial to
toughening; (ii) fibers of relatively high elastic modulus compared to
the matrix may result in substantial matrix damage due to spalling
effect; (iii) employment of high-strength synthetic fibers is a good
option for toughening. We expect that the combination of the discrete
element method (DEM) with the finite element method (FEM) can
increase the versatility and efficiency of the software developed. The
present work can guide the design of ceramic composites of high
performance through the optimization of the parameters.
Abstract: Everyday life is and will be influenced depending on
the developments that society undergoes throughout the history.
Particularly, countries undergoing transition from one system to
another sustain the greatest impact in trying to embrace the modern
system. Kosovo society had the fortune to experience a change,
which began in late 1999 to continue up to date. One of the
'developments' of the time with the evolution in Kosovo society was
the transition from the traditional education system into the modern
one. This transformation began immediately after the war, to
continue even today. It was started by internationals, which governed
and administered Kosovo society, including education. There was a
great 'evolution', because almost the entire system was 'changed'.
Among other things, for the first time it was enabled the opening of
private schools from the lowest level up to the colleges and
universities. This paper will address: how much was ready the society
to embrace such a 'cultural' change in education, respectively, how
much were prepared teachers for such changes; as it was actually
thought to be a modern education system, how much was it according
to international standards; what are the results and current situation in
Kosovo education.
Abstract: This research aimed to study the characteristics of a
community in the social, economic and cultural context. This
research used interviews and surveys of the members in the Patthana
Soi Ranongklang community, Dusit District, Bangkok. The results
are as follows: In terms of overall conditions and characteristics, the
Patthana Soi Ranongklang community is located on the property of
the Treasury Department. 50 years ago, the location of this
community consisted of paddy fields with limited convenience in
terms of transportation. Rama V Road was only a small narrow road
accessed only by three-wheelers there were no buses. The majority of
community members moved in from Mak Khawan Rangsan Bridge.
Thus, most community members were either workers or government
officials as they were routers not the owners of the land. Therefore,
there were no primary occupations within the 7 acres of this
community. The development of the community started in 1981. At
present, the community is continuously being developed and
modernization is rapidly flowing in. One of the reasons was because
the main roads were widened, especially Rama V Road that allows
more convenient transportation, leading to heightened citizens’
convenience. In terms of the economy and society, Rama V Road
causes the research to find out the development and expansion of
change in the conditions of the area and buildings. Some buildings
were improved and changed along the time, as well as the
development of new facilities that caused the community members to
continually become more materialistic. In the community, it has well
organized and managed jobs to each part of community members,
and areas were improved to allow the new buildings and apartments.
The trend of jobs became more varied, in terms of both jobs at home,
such as workers, merchandizing and small own businesses, and the
community jobs outside, which became much more convenient to car
drivers as they got used to the narrow roads inside the community.
The location of the community next to Rama V Road also allows
assistance from government agencies to reach the community with
ease. Moreover, the welfare of the community was well taken care of
by the community committee. In terms of education, the research
found that there are two schools: Wat Pracharabuedham School and
Wat Noi Noppakun School that are providing education within the
community. The majority in the community have received Bachelor
degrees. In areas of culture, the research found that the culture,
traditions and beliefs of people in the community were mainly
transferred from the old community: the majorities are Buddhists, so
especially beliefs in Buddhism; the main reason for this is because
the old community was situated near Wat Makut Kasattriyaram.
Therefore, the community members have always had Buddhist
temples as the centre of the community. Later years, more citizens
moved along culture in and bring traditions and beliefs with them.
The community members also took part in building a Dharma hall
named Wat Duang Jai which is 72 year old.
Abstract: Zinc oxide (ZnO) is one of the light emitting materials in ultraviolet (UV) region. In addition, ZnO nanostructures are also attracting increasing research interest as buildingblocks for UV optoelectronic applications. We have succeeded in synthesizing vertically-aligned ZnO nanostructures by laser interference patterning, which is catalyst-free and non-contact technique. In this study, vertically-aligned ZnO nanowall arrays were synthesized using two-beam interference. The maximum height and average thickness of the ZnO nanowalls were about 4.5µm and 200 nm, respectively.UV lasing from a piece of the ZnO nanowall was obtained under the third harmonic of a Q-switched Nd:YAG laser excitation, and the estimated threshold power density for lasing was about 150 kW/cm2. Furthermore, UV lasing from the vertically-aligned ZnO nanowall was also achieved. The results indicate that ZnO nanowalls can be applied to random laser.
Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.
Abstract: In medical imaging, segmentation of different areas of
human body like bones, organs, tissues, etc. is an important issue.
Image segmentation allows isolating the object of interest for further
processing that can lead for example to 3D model reconstruction of
whole organs. Difficulty of this procedure varies from trivial for
bones to quite difficult for organs like liver. The liver is being
considered as one of the most difficult human body organ to segment.
It is mainly for its complexity, shape versatility and proximity of
other organs and tissues. Due to this facts usually substantial user
effort has to be applied to obtain satisfactory results of the image
segmentation. Process of image segmentation then deteriorates from
automatic or semi-automatic to fairly manual one. In this paper,
overview of selected available software applications that can handle
semi-automatic image segmentation with further 3D volume
reconstruction of human liver is presented. The applications are being
evaluated based on the segmentation results of several consecutive
DICOM images covering the abdominal area of the human body.
Abstract: The transition period of Kosovo society brought
fundamental changes in all the spheres of organizing life. This was
the period when also in the cultural tradition the biggest movement
and an emerging from ‘isolation’ or from the ‘shell’ occurred.
Transformation of the traditional and embracing of the modern began
here. The same was experienced and is currently being experienced
also by Gjakova and its surrounding which is historically renowned
for its great tradition and culture.
The population of this region is actually facing a transition from
the traditional system into the modern one and quite often with huge
leaps.
These ‘movements’ or ‘evolutions’ of the society of this region,
besides the numerous positive things it ‘harvested’, also brought
things that do not at all correspond with their tradition as well as new
criminal occurrences which in the past were not present in this area.
Furthermore, some of the ‘new’ behaviors that are embraced from
other ‘cultures’ and ‘civilizations’, and which are often exceeded, are
quite perturbing. The security situation is also worrying, particularly
following the appearance of some new criminal occurrences.
Therefore, with this research paper we will strive to analyze the
new cultural “intersections” as well as the nature of the origin of
some new very worrying criminal occurrences. We will present there
also some factors inciting into these occurrences, which were
confessed by the persons involved in these criminal occurrences and
who come from this very region.
Abstract: A key issue in seismic risk analysis within the context
of Performance-Based Earthquake Engineering is the evaluation of
the expected seismic damage of structures under a specific
earthquake ground motion. The assessment of the seismic
performance strongly depends on the choice of the seismic Intensity
Measure (IM), which quantifies the characteristics of a ground
motion that are important to the nonlinear structural response. Several
conventional IMs of ground motion have been used to estimate their
damage potential to structures. Yet, none of them has been proved to
be able to predict adequately the seismic damage. Therefore,
alternative, scalar intensity measures, which take into account not
only ground motion characteristics but also structural information
have been proposed. Some of these IMs are based on integration of
spectral values over a range of periods, in an attempt to account for
the information that the shape of the acceleration, velocity or
displacement spectrum provides. The adequacy of a number of these
IMs in predicting the structural damage of 3D R/C buildings is
investigated in the present paper. The investigated IMs, some of
which are structure specific and some are non structure-specific, are
defined via integration of spectral values. To achieve this purpose
three symmetric in plan R/C buildings are studied. The buildings are
subjected to 59 bidirectional earthquake ground motions. The two
horizontal accelerograms of each ground motion are applied along
the structural axes. The response is determined by nonlinear time
history analysis. The structural damage is expressed in terms of the
maximum interstory drift as well as the overall structural damage
index. The values of the aforementioned seismic damage measures
are correlated with seven scalar ground motion IMs. The comparative
assessment of the results revealed that the structure-specific IMs
present higher correlation with the seismic damage of the three
buildings. However, the adequacy of the IMs for estimation of the
structural damage depends on the response parameter adopted.
Furthermore, it was confirmed that the widely used spectral
acceleration at the fundamental period of the structure is a good
indicator of the expected earthquake damage level.
Abstract: The present study involved analysis of certain
characteristics of the perennial ryegrass (Lolium perenne L.)
genotypes collected from the natural flora of Ankara, and explores a
correlation among them. In order to evaluate the plants for breeding
purpose as per Turkey's environmental conditions, the perennial
ryegrass plants were collected from natural pasture of Ankara in 2004
and were utilized for the study. Seeds of the collected plants were
sown in pots and seedlings were prepared in a greenhouse. In 2005,
the seedlings were transplanted at 50 × 50 cm2 intervals in
Randomized Complete Blocks Design in an experimental field. In
2007 and 2008, data were recorded from the observations and
measurements of 568 perennial ryegrasses. The plant characteristics,
which were investigated, included re-growth time in spring, color,
density, growth habit, tendency to form inflorescence, time of
inflorescence, plant height, length of upper internode, spike length,
leaf length, leaf width, leaf area, leaf shape, number of spikelets per
spike, seed yield per spike and 1000 grain weight and the correlation
analyses were made using this data. Correlation coefficients were
estimated between all paired combinations of the studied traits. The
yield components exhibited varying trends of association among
themselves. Seed yield per spike showed significant and positive
association with the number of spikelets per spike, 1000 grain weight,
plant height, length of upper internode, spike length, leaf length, leaf
width, leaf area and color, but significant and negative association
with the growth habit and re-growth time in spring.