Abstract: It is essential to have a uniform and calm flow field
for a settling tank to have high performance. In general, the
recirculation zones always occurred in sedimentation tanks. The
presence of these regions may have different effects. The nonuniformity
of the velocity field, the short-circuiting at the surface and
the motion of the jet at the bed of the tank that occurs because of the
recirculation in the sedimentation layer, are affected by the geometry
of the tank. There are some ways to decrease the size of these dead
zones, which would increase the performance. One of the ways is to
use a suitable baffle configuration. In this study, the presence of
baffle with different position has been investigated by a finite volume
method, with VOF (Volume of Fluid) model. Besides, the k-ε
turbulence model is used in the numerical calculations. The results
indicate that the best position of the baffle is obtained when the
volume of the recirculation region is minimized or is divided to
smaller part and the flow field trend to be uniform in the settling
zone.
Abstract: A simple method for the simultaneous determination
of hippuric acid and benzoic acid in urine using reversed-phase high
performance liquid chromatography was described. Chromatography
was performed on a Nova-Pak C18 (3.9 x 150 mm) column with a
mobile phase of mixed solution methanol: water: acetic acid
(20:80:0.2) and UV detection at 254 nm. The calibration curve was
linear within concentration range at 0.125 to 6.0 mg/ml of hippuric
acid and benzoic acid. The recovery, accuracy and coefficient
variance of hippuric acid were 104.54%, 0.2% and 0.2% respectively
and for benzoic acid were 98.48%, 1.25% and 0.60% respectively.
The detection limit of this method was 0.01ng/l for hippuric acid and
0.06ng/l for benzoic acid. This method has been applied to the
analysis of urine samples from the suspected of toluene abuser or
glue sniffer among secondary school students at Johor Bahru.
Abstract: In this paper, we propose a fully-utilized, block-based 2D DWT (discrete wavelet transform) architecture, which consists of four 1D DWT filters with two-channel QMF lattice structure. The proposed architecture requires about 2MN-3N registers to save the intermediate results for higher level decomposition, where M and N stand for the filter length and the row width of the image respectively. Furthermore, the proposed 2D DWT processes in horizontal and vertical directions simultaneously without an idle period, so that it computes the DWT for an N×N image in a period of N2(1-2-2J)/3. Compared to the existing approaches, the proposed architecture shows 100% of hardware utilization and high throughput rates. To mitigate the long critical path delay due to the cascaded lattices, we can apply the pipeline technique with four stages, while retaining 100% of hardware utilization. The proposed architecture can be applied in real-time video signal processing.
Abstract: A high performance computer includes a fast
processor and millions bytes of memory. During the data processing,
huge amount of information are shuffled between the memory and
processor. Because of its small size and its effectiveness speed, cache
has become a common feature of high performance computers.
Enhancing cache performance proved to be essential in the speed up
of cache-based computers. Most enhancement approaches can be
classified as either software based or hardware controlled. The
performance of the cache is quantified in terms of hit ratio or miss
ratio. In this paper, we are optimizing the cache performance based
on enhancing the cache hit ratio. The optimum cache performance is
obtained by focusing on the cache hardware modification in the way
to make a quick rejection to the missed line's tags from the hit-or
miss comparison stage, and thus a low hit time for the wanted line in
the cache is achieved. In the proposed technique which we called
Even- Odd Tabulation (EOT), the cache lines come from the main
memory into cache are classified in two types; even line's tags and
odd line's tags depending on their Least Significant Bit (LSB). This
division is exploited by EOT technique to reject the miss match line's
tags in very low time compared to the time spent by the main
comparator in the cache, giving an optimum hitting time for the
wanted cache line. The high performance of EOT technique against
the familiar mapping technique FAM is shown in the simulated
results.
Abstract: Dedicated Short Range Communication (DSRC) is a
key enabling technology for the next generation of
communication-based safety applications. One of the important
problems for DSRC deployment is maintaining high performance
under heavy channel load. Many studies focus on congestion control
mechanisms for simulating hundreds of physical radios deployed on
vehicles. The U.S. department of transportation-s (DOT) Intelligent
Transportation Systems (ITS) division has a plan to chosen prototype
on-board devices capable of transmitting basic “Here I am" safety
messages to other vehicles. The devices will be used in an IntelliDrive
safety pilot deployment of up to 3,000 vehicles. It is hard to log the
information of 3,000 vehicles. In this paper we present the designs and
issues related to the DSRC Radio Testbed under heavy channel load.
The details not only include the architecture of DSRC Radio Testbed,
but also describe how the Radio Interfere System is used to help for
emulating the congestion radio environment.
Abstract: RF performance of SOI CMOS device has attracted
significant amount of interest recently. In order to improve RF
parameters, Strained Si/Relaxed Si0.8Ge0.2 investigated as a
replacement for Si technology .Enhancement of carrier mobility
associated with strain engineering makes Strained Si a promising
candidate for improving RF performance of CMOS technology.
From the simulation, the cut-off frequency is estimated to be 224
GHZ, whereas in SOI at similar bias is about 188 GHZ. Therefore,
Strained Si exhibits 19% improvement in cut-off frequency over
similar Si counterpart. In this paper, Ion/Ioff ratio is studied as one of
the key parameters in logic and digital application. Strained Si/SiGe
demonstrates better Ion/Ioff characteristic than SOI, in similar channel
length of 100 nm.Another important key analog figures of merit such
as Early Voltage (VEA) ,transconductance vs drain current (gm /Ids)
are studied. They introduce the efficiency of the devices to convert
dc power into ac frequency.
Abstract: Since 1984 many schemes have been proposed for
digital signature protocol, among them those that based on discrete
log and factorizations. However a new identification scheme based
on iterated function (IFS) systems are proposed and proved to be
more efficient. In this study the proposed identification scheme is
transformed into a digital signature scheme by using a one way hash
function. It is a generalization of the GQ signature schemes. The
attractor of the IFS is used to obtain public key from a private one,
and in the encryption and decryption of a hash function. Our aim is
to provide techniques and tools which may be useful towards
developing cryptographic protocols. Comparisons between the
proposed scheme and fractal digital signature scheme based on RSA
setting, as well as, with the conventional Guillou-Quisquater
signature, and RSA signature schemes is performed to prove that, the
proposed scheme is efficient and with high performance.
Abstract: Long term rainfall analysis and prediction is a
challenging task especially in the modern world where the impact of
global warming is creating complications in environmental issues.
These factors which are data intensive require high performance
computational modeling for accurate prediction. This research paper
describes a prototype which is designed and developed on grid
environment using a number of coupled software infrastructural
building blocks. This grid enabled system provides the demanding
computational power, efficiency, resources, user-friendly interface,
secured job submission and high throughput. The results obtained
using sequential execution and grid enabled execution shows that
computational performance has enhanced among 36% to 75%, for
decade of climate parameters. Large variation in performance can be
attributed to varying degree of computational resources available for
job execution.
Grid Computing enables the dynamic runtime selection, sharing
and aggregation of distributed and autonomous resources which plays
an important role not only in business, but also in scientific
implications and social surroundings. This research paper attempts to
explore the grid enabled computing capabilities on weather indices
from HOAPS data for climate impact modeling and change
detection.
Abstract: Nigerian bread is baked with vitamin A fortified wheat flour. Study aimed at determining its contribution to preschoolers- vitamin A nutriture. A cross-sectional/experimental study was carried out in four poor-urban Local Government Areas (LGAs) of Metropolitan Lagos, Nigeria. A pretested food frequency questionnaire was administered to randomly selected mothers of 1600 preschoolers (24-59 months). Retinyl Palmitate content of fourteen bread samples randomly collected from bakeries in all LGAs was analyzed at 0 and 5 days at 25oC using High Performance Liquid Chromatography. Data analysis was done at p
Abstract: The highly nonlinear characteristics of drying
processes have prompted researchers to seek new nonlinear control
solutions. However, the relation between the implementation
complexity, on-line processing complexity, reliability control
structure and controller-s performance is not well established. The
present paper proposes high performance nonlinear fuzzy controllers
for a real-time operation of a drying machine, being developed under
a consistent match between those issues. A PCI-6025E data
acquisition device from National Instruments® was used, and the
control system was fully designed with MATLAB® / SIMULINK
language. Drying parameters, namely relative humidity and
temperature, were controlled through MIMOs Hybrid Bang-bang+PI
(BPI) and Four-dimensional Fuzzy Logic (FLC) real-time-based
controllers to perform drying tests on biological materials. The
performance of the drying strategies was compared through several
criteria, which are reported without controllers- retuning. Controllers-
performance analysis has showed much better performance of FLC
than BPI controller. The absolute errors were lower than 8,85 % for
Fuzzy Logic Controller, about three times lower than the
experimental results with BPI control.
Abstract: with increasing circuits- complexity and demand to
use portable devices, power consumption is one of the most
important parameters these days. Full adders are the basic block of
many circuits. Therefore reducing power consumption in full adders
is very important in low power circuits. One of the most powerconsuming
modules in full adders is XOR/XNOR circuit. This paper
presents two new full adders based on two new logic approaches. The
proposed logic approaches use one XOR or XNOR gate to implement
a full adder cell. Therefore, delay and power will be decreased. Using
two new approaches and two XOR and XNOR gates, two new full
adders have been implemented in this paper. Simulations are carried
out by HSPICE in 0.18μm bulk technology with 1.8V supply voltage.
The results show that the ten-transistors proposed full adder has 12%
less power consumption and is 5% faster in comparison to MB12T
full adder. 9T is more efficient in area and is 24% better than similar
10T full adder in term of power consumption. The main drawback of
the proposed circuits is output threshold loss problem.
Abstract: Image mosaicing is a technique that permits to enlarge the field of view of a camera. For instance, it is employed to achieve panoramas with common cameras or even in scientific applications, to achieve the image of a whole culture in microscopical imaging. Usually, a mosaic of cell cultures is achieved through using automated microscopes. However, this is often performed in batch, through CPU intensive minimization algorithms. In addition, live stem cells are studied in phase contrast, showing a low contrast that cannot be improved further. We present a method to study the flat field from live stem cells images even in case of 100% confluence, this permitting to build accurate mosaics on-line using high performance algorithms.
Abstract: Renewable natural fibres such as oil palm, flax, and
pineapple leaf can be utilized to obtain new high performance
polymer materials. The reuse of waste natural fibres as reinforcement
for polymer is a sustainable option to the environment. However, due
to its high hydroxyl content of cellulose, natural fibres are
susceptible to absorb water that affects the composite mechanical
properties adversely. Research found that Nano materials such as
Nano Silica Carbide (n-SiC) and Nano Clay can be added into the
polymer composite to overcome this problem by enhancing its
mechanical properties in wet condition. The addition of Nano
material improves the tensile and wear properties, flexural stressstrain
behaviour, fracture toughness, and fracture strength of polymer
natural composites in wet and dry conditions.
Abstract: Many studies have shown that parallelization decreases efficiency [1], [2]. There are many reasons for these decrements. This paper investigates those which appear in the context of parallel data integration. Integration processes generally cannot be allocated to packages of identical size (i. e. tasks of identical complexity). The reason for this is unknown heterogeneous input data which result in variable task lengths. Process delay is defined by the slowest processing node. It leads to a detrimental effect on the total processing time. With a real world example, this study will show that while process delay does initially increase with the introduction of more nodes it ultimately decreases again after a certain point. The example will make use of the cloud computing platform Hadoop and be run inside Amazon-s EC2 compute cloud. A stochastic model will be set up which can explain this effect.
Abstract: This paper presents an architecture of current filesystem
implementations as well as our new filesystem SpadFS and operating
system Spad with rewritten VFS layer targeted at high performance
I/O applications. The paper presents microbenchmarks and real-world
benchmarks of different filesystems on the same kernel as well as
benchmarks of the same filesystem on different kernels – enabling
the reader to make conclusion how much is the performance of
various tasks affected by operating system and how much by physical
layout of data on disk. The paper describes our novel features–most
notably continuous allocation of directories and cross-file readahead
– and shows their impact on performance.
Abstract: In this paper, the implementation of low power,
high throughput convolutional filters for the one dimensional
Discrete Wavelet Transform and its inverse are presented. The
analysis filters have already been used for the implementation of a
high performance DWT encoder [15] with minimum memory
requirements for the JPEG 2000 standard. This paper presents the
design techniques and the implementation of the convolutional filters
included in the JPEG2000 standard for the forward and inverse DWT
for achieving low-power operation, high performance and reduced
memory accesses. Moreover, they have the ability of performing
progressive computations so as to minimize the buffering between
the decomposition and reconstruction phases. The experimental
results illustrate the filters- low power high throughput characteristics
as well as their memory efficient operation.
Abstract: A high performance thin layer chromatography
system (HPTLC) for the separation of vitamin B2 and B12 has been
developed. The separation was successfully using a solvent system of
methanol, water, ammonia 7.3.1 (V/V) as mobile phase on HPTLC
plates impregnated with boric acid. The effect of other mobile phases
on the separation of vitamins was also examined. The method is
based on different behavior of investigated compounds in
impregnated TLC plates with different amount of boric acid. The Rf
values of vitamin B2 and B12 are considered on non impregnated
and impregnated silica gel HPTLC plate with boric acid. The effect
of boric acid in the mobile phase and on HPTLC plates on the RF
values of the vitamins has also been studied.
Abstract: Large-scale systems such as Grids offer
infrastructures for both data distribution and parallel processing. The
use of Grid infrastructures is a more recent issue that is already
impacting the Distributed Database Management System industry. In
DBMS, distributed query processing has emerged as a fundamental
technique for ensuring high performance in distributed databases.
Database placement is particularly important in large-scale systems
because it reduces communication costs and improves resource
usage. In this paper, we propose a dynamic database placement
policy that depends on query patterns and Grid sites capabilities. We
evaluate the performance of the proposed database placement policy
using simulations. The obtained results show that dynamic database
placement can significantly improve the performance of distributed
query processing.
Abstract: The need for micromechanical inertial sensors is increasing
in future electronic stability control (ESC) and other positioning,
navigation and guidance systems. Due to the rising density of
sensors in automotive and consumer devices the goal is not only to get
high performance, robustness and smaller package sizes, but also to
optimize the energy management of the overall sensor system. This
paper presents an evaluation concept for a surface micromachined
yaw rate sensor. Within this evaluation concept an energy-efficient
operation of the drive mode of the yaw rate sensor is enabled. The
presented system concept can be realized within a power management
subsystem.
Abstract: This paper presents a novel template-based method to
detect objects of interest from real images by shape matching. To
locate a target object that has a similar shape to a given template
boundary, the proposed method integrates three components: contour
grouping, partial shape matching, and boundary verification. In the
first component, low-level image features, including edges and
corners, are grouped into a set of perceptually salient closed contours
using an extended ratio-contour algorithm. In the second component,
we develop a partial shape matching algorithm to identify the
fractions of detected contours that partly match given template
boundaries. Specifically, we represent template boundaries and
detected contours using landmarks, and apply a greedy algorithm to
search the matched landmark subsequences. For each matched
fraction between a template and a detected contour, we estimate an
affine transform that transforms the whole template into a hypothetic
boundary. In the third component, we provide an efficient algorithm
based on oriented edge lists to determine the target boundary from
the hypothetic boundaries by checking each of them against image
edges. We evaluate the proposed method on recognizing and
localizing 12 template leaves in a data set of real images with clutter
back-grounds, illumination variations, occlusions, and image noises.
The experiments demonstrate the high performance of our proposed
method1.