Abstract: Solution for the complete removal of carbon
monoxide from the exhaust gases still poses a challenge to the
researchers and this problem is still under development. Modeling for
reduction of carbon monoxide is carried out using heterogeneous
reaction using low cost non-noble metal based catalysts for the
purpose of controlling emissions released to the atmosphere. A
simple one-dimensional model was developed for the monolith using
hopcalite catalyst. The converter is assumed to be an adiabatic
monolith operating under warm-up conditions. The effect of inlet gas
temperatures and catalyst loading on carbon monoxide reduction
during cold start period in the converter is analysed.
Abstract: The phenomenon of global warming or climate
change has led to many environmental issues including higher
atmospheric temperatures, intense precipitation, increased
greenhouse gaseous emissions and increased indoor discomfort.
Studies have shown that bringing nature to the roof such as
constructing green roof and implementing high-reflective roof may
give positive impact in mitigating the effects of global warming and
in increasing thermal comfort sensation inside buildings. However,
no study has been conducted to compare both types of passive roof
treatments in Malaysia in order to increase thermal comfort in
buildings. Therefore, this study is conducted to investigate the effect
of green roof and white painted roof as passive roof treatment in
improving indoor comfort of Malaysian homes. This study uses an
experimental approach in which the measurements of temperatures
are conducted on the case study building. The measurements of
outdoor and indoor environments were conducted on the flat roof
with two different types of roof treatment that are green roof and
white roof. The measurement of existing black bare roof was also
conducted to act as a control for this study.
Abstract: The last Assessment Report of the Intergovernmental
Panel on Climate Change, stating that the greatest risk in climate
change affects sustainability is now widely known and accepted.
However, it has not provoked substantial reaction and attention in
Hungary, while international and national efforts have also not
achieved expected results so far. Still, there are numerous examples
on different levels (national, regional, local, household) making
considerable progress in limiting their own emissions and making
steps toward mitigation of and adaptation to climate change. The
local level is exceptionally important in sustainability adaptation, as
local communities are often able to adapt more flexibly to changes in
the natural environment.The aim of this paper is to attempt a review
of the national climate policy and the local climate change strategies
in Hungary considering sustainable development.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: Hydrogen that used as fuel in fuel cell vehicles can be
produced from renewable sources such as wind, solar, and hydro
technologies. PV-electrolyzer is one of the promising methods to
produce hydrogen with zero pollution emission. Hydrogen
production from a PV-electrolyzer system depends on the efficiency
of the electrolyzer and photovoltaic array, and sun irradiance at that
site. In this study, the amount of hydrogen is obtained using
mathematical equations for difference driving distance and sun peak
hours. The results show that the minimum of 99 PV modules are used
to generate 1.75 kgH2 per day for two vehicles.
Abstract: A Positron Emission Tomography (PET) is a radioisotope imaging technique that illustrates the organs and the metabolisms of the human body. This technique is based on the simultaneous detection of 511 keV annihilation photons, annihilated as a result of electrons annihilating positrons that radiate from positron-emitting radioisotopes that enter biological active molecules in the body. This study was conducted on ten patients in an effort to conduct patient-related experimental studies. Dosage monitoring for the bladder, which was the organ that received the highest dose during PET applications, was conducted for 24 hours. Assessment based on measuring urination activities after injecting patients was also a part of this study. The MIRD method was used to conduct dosage calculations for results obtained from experimental studies. Results obtained experimentally and theoretically were assessed comparatively.
Abstract: Proximate (moisture, protein, total fat, total ash) and mineral (K, P, Na, Mg, Ca, Zn, Fe, Cu and Mn) composition of chicken giblets (heart, liver and gizzard) were investigated. Phosphorous content, as well as proximate composition, were determined according to recommended ISO methods. The content of all elements, except phosphorus, of the giblets tissues were determined using inductively coupled plasma-optical emission spectrometry (ICP-OES), after dry ashing mineralization. Regarding proximate composition heart was the highest in total fat content, and the lowest in protein content. Liver was the highest in protein and total ash content, while gizzard was the highest in moisture and the lowest in total fat content. Regarding mineral composition liver was the highest for K, P, Ca, Mg, Fe, Zn, Cu, and Mn, while heart was the highest for Na content. The contents of almost all investigated minerals in analysed giblets tissues of chickens from Vojvodina were similar to values reported in the literature, i.e. in national food composition databases of other countries.
Abstract: Two seperate experiments by barley and alfalfa were
conducted to a 2×8 factorial completely randomised design, with four
replicates. Factors were inoculation (M) with Gomus mosseae or uninoculation
(M0) and seven levels of contaminants (Co, Cd, Pb and
combinations) plus an uncontaminated control treatment (C). Heavy
metals in plant tissues and soil were quantified by Inductively
Coupled Plasma Optical Emission Spectrometer (ICP-OES) (Variant-
Liberty 150AX Turbo). Phytoextraction coefficient of contaminants
calculated by concentration of heavy metals in the shoot (mgkg-1) /
concentration of heavy metals in soil (mgkg-1). In the barley, the
highest rate of phytoextraction coefficient of Pb, Cd and Co was in
M0Pb, M0PbCoCd and MCo, respectively (P
Abstract: This paper presents an environmental and technoeconomic
evaluation of light duty vehicles in Iran. A comprehensive
well-to-wheel (WTW) analysis is applied to compare different
automotive fuel chains, conventional internal combustion engines and
innovative vehicle powertrains. The study examines the
competitiveness of 15 various pathways in terms of energy
efficiencies, GHG emissions, and levelized cost of different energy
carriers. The results indicate that electric vehicles including battery
electric vehicles (BEV), fuel cell vehicles (FCV) and plug-in hybrid
electric vehicles (PHEV) increase the WTW energy efficiency by
54%, 51% and 46%, respectively, compared to common internal
combustion engines powered by gasoline. On the other hand,
greenhouse gas (GHG) emissions per kilometer of FCV and BEV
would be 48% lower than that of gasoline engines. It is concluded
that BEV has the lowest total cost of energy consumption and
external cost of emission, followed by internal combustion engines
(ICE) fueled by CNG. Conventional internal combustion engines
fueled by gasoline, on the other hand, would have the highest costs.
Abstract: The reduction in vehicle exhaust emissions achieved
in the last two decades is offset by the growth in traffic, as well as by
changes in the composition of emitted pollutants. The present
investigation illustrates the emissions of in-use gasoline and diesel
passenger cars using the official European driving cycle and the
ARTEMIS real-world driving cycle. It was observed that some of the
vehicles do not comply with the corresponding regulations.
Significant differences in emissions were observed between driving
cycles. Not all pollutants showed a tendency to decrease from Euro 3
to Euro 5.
Abstract: Post growth annealing of solution grown ZnO
nanowire array is performed under controlled oxygen ambience. The
role of annealing over surface defects and their consequence on
dark/photo-conductivity and photosensitivity of nanowire array is
investigated. Surface defect properties are explored using various
measurement tools such as contact angle, photoluminescence, Raman
spectroscopy and XPS measurements. The contact angle of the NW
films reduces due to oxygen annealing and nanowire film surface
changes from hydrophobic (96°) to hydrophilic (16°). Raman and
XPS spectroscopy reveal that oxygen annealing improves the crystal
quality of the nanowire films. The defect band emission intensity
(relative to band edge emission, ID/IUV) reduces from 1.3 to 0.2 after
annealing at 600 °C at 10 SCCM flow of oxygen. An order
enhancement in dark conductivity is observed in O2 annealed
samples, while photoconductivity is found to be slightly reduced due
to lower concentration of surface related oxygen defects.
Abstract: Fabrication and efficiency enhancement of non-mercury, high efficiency and green field emission lamps using carbon nano-materials such as carbon nanotubes as cathode field emitters was studied. Phosphor was coated on the ITO glass or metal substrates as the anode. The luminescence efficiency enhancement was carried out by upgrading the uniform of the emitters, improving electron and thermal conductivity of the phosphor and the optimization of the design of different cathode/anode configurations. After evaluation of the aforementioned parameters, the luminescence efficiency of the field emission lamps was raised.
Abstract: The analysis of Acoustic Emission (AE) signal
generated from metal cutting processes has often approached
statistically. This is due to the stochastic nature of the emission
signal as a result of factors effecting the signal from its generation
through transmission and sensing. Different techniques are applied in
this manner, each of which is suitable for certain processes. In metal
cutting where the emission generated by the deformation process is
rather continuous, an appropriate method for analysing the AE signal
based on the root mean square (RMS) of the signal is often used and
is suitable for use with the conventional signal processing systems.
The aim of this paper is to set a strategy in tool failure detection in
turning processes via the statistic analysis of the AE generated from
the cutting zone. The strategy is based on the investigation of the
distribution moments of the AE signal at predetermined sampling.
The skews and kurtosis of these distributions are the key elements in
the detection. A normal (Gaussian) distribution has first been
suggested then this was eliminated due to insufficiency. The so
called Beta distribution was then considered, this has been used with
an assumed β density function and has given promising results with
regard to chipping and tool breakage detection.
Abstract: In this study, a reformer model simulation to use
refinery (Farashband refinery, Iran) waste natural gas. In the
petroleum and allied sectors where natural gas is being encountered
(in form of associated gas) without prior preparation for its positive
use, its combustion (which takes place in flares, an equipment through
which they are being disposed) has become a great problem because
of its associated environmental problems in form of gaseous emission.
The proposed model is used to product syngas from waste natural gas.
A detailed steady model described by a set of ordinary differential and
algebraic equations was developed to predict the behavior of the
overall process. The proposed steady reactor model was validated
against process data of a reformer synthesis plant recorded and a good
agreement was achieved. H2/CO ratio has important effect on Fischer-
Tropsch synthesis reactor product and we try to achieve this parameter
with best designing reformer reactor. We study different kind of
reformer reactors and then select auto thermal reforming process of
natural gas in a fixed bed reformer that adjustment H2/CO ratio with
CO2 and H2O injection. Finally a strategy was proposed for prevention
of extra natural gas to atmosphere.
Abstract: In this paper, an Interactive Compromise Approach
with Particle Swarm Optimization(ICA-PSO) is presented to solve the
Economic Emission Dispatch(EED) problem. The cost function and
emission function are modeled as the nonsmooth functions,
respectively. The bi-objective including both the minimization of cost
and emission is formulated in this paper. ICA-PSO is proposed to
solve EED problem for finding a better compromise solution. The
solution methodology can offer a global or near-global solution for
decision-making requirements. The effectiveness and efficiency of
ICA-PSO are demonstrated by a sample test system. Test results can
be shown that the proposed method provide a practical and flexible
framework for power dispatch.
Abstract: The power consumption of an Optical Packet Switch
equipped with SOA technology based Spanke switching fabric is
evaluated. Sophisticated analytical models are introduced to evaluate
the power consumption versus the offered traffic, the main
switch parameters, and the used device characteristics. The impact
of Amplifier Spontaneous Emission (ASE) noise generated by a
transmission system on the power consumption is investigated. As
a matter of example for 32×32 switches supporting 64 wavelengths
and offered traffic equal to 0,8, the average energy consumption per
bit is 5, 07 · 10-2 nJ/bit and increases if ASE noise introduced by
the transmission systems is increased.
Abstract: Buildings and associated construction methods have a significant impact on the environment. As construction activity increases in Kuwait, there is a need to create design and construction strategies which will minimize the environmental impact of new buildings. Green construction is a design philosophy intended to improve the sustainability of construction by the minimization of resource depletion and CO2 emissions throughout the life cycle of buildings. This paper presents and discusses the results of a survey that was conducted in Kuwait, with the objective of investigating the awareness of developers and other stakeholders regarding their understanding and use of green construction strategies. The results of the survey demonstrate that whilst there seems to be a reasonable level of awareness amongst the stakeholders, this awareness is not currently well reflected in the design and construction practices actually being applied. It is therefore concluded is there is a pressing need for intervention from Government in order that the use of sustainable green design and construction strategies becomes the norm in Kuwait.
Abstract: The CMLP building was developed to be a model for
sustainability with strategies to reduce water, energy and pollution,
and to provide a healthy environment for the building occupants. The
aim of this paper is to investigate the environmental effects of energy
used by this building. A LCA (life cycle analysis) was led to measure
the real environmental effects produced by the use of energy. The
impact categories most affected by the energy use were found to be
the human health effects, as well as ecotoxicity. Natural gas
extraction, uranium milling for nuclear energy production, and the
blasting for mining and infrastructure construction are the processes
contributing the most to emissions in the human health effect. Data
comparing LCA results of CMLP building with a conventional
building results showed that energy used by the CMLP building has
less damage for the environment and human health than a
conventional building.
Abstract: In this study, the ability of Aspergillus niger and
Penicillium simplicissimum to extract heavy metals from a spent
refinery catalyst was investigated. For the first step, a spent
processing catalyst from one of the oil refineries in Iran was
physically and chemically characterized. Aspergillus niger and
Penicillium simplicissimum were used to mobilize Al/Co/Mo/Ni from
hazardous spent catalysts. The fungi were adapted to the mixture of
metals at 100-800 mg L-1 with increments in concentration of 100 mg
L-1. Bioleaching experiments were carried out in batch cultures. To
investigate the production of organic acids in sucrose medium,
analyses of the culture medium by HPLC were performed at specific
time intervals after inoculation. The results obtained from Inductive
coupled plasma-optical emission spectrometry (ICP-OES) showed
that after the one-step bioleaching process using Aspergillus niger,
maximum removal efficiencies of 27%, 66%, 62% and 38% were
achieved for Al, Co, Mo and Ni, respectively. However, the highest
removal efficiencies using Penicillium simplicissimum were of 32%,
67%, 65% and 38% for Al, Co, Mo and Ni, respectively
Abstract: Copper sulfide nanoparticles (CuS) were successfully synthesized by the pulsed plasma in liquid method, using two copper rod electrodes submerged in molten sulfur. Low electrical energy and no high temperature were applied for synthesis. Obtained CuS nanoparticles were then analyzed by means of X-ray diffraction, Low and High Resolution Transmission Electron Microscopy, Electron Diffraction, X-ray Photoelectron, Raman Spectroscopies and Field Emission Scanning Electron Microscopy. XRD analysis revealed peaks for CuS with hexagonal phase composition. TEM and HRTEM studies showed that sizes of CuS nanoparticles ranged between 10-60 nm, with the average size of about 20 nm. Copper sulfide nanoparticles have short nanorod-like structure. Raman spectroscopy found peak for CuS at 474.2cm-1of Raman region.