Abstract: The influence of axial magnetic field (B=0.48 T) on
the variation of ionization efficiency coefficient h and secondary
electron emission coefficient g with respect to reduced electric field
E/P is studied at a new range of plane-parallel electrode spacing (0<
d< 20 cm) and different nitrogen working pressure between 0.5-20
Pa. The axial magnetic field is produced from an inductive copper
coil of radius 5.6 cm. The experimental data of breakdown voltage is
adopted to estimate the mean Paschen curves at different working
features. The secondary electron emission coefficient is calculated
from the mean Paschen curve and used to determine the minimum
breakdown voltage. A reduction of discharge voltage of about 25% is
investigated by the applied of axial magnetic field. At high interelectrode
spacing, the effect of axial magnetic field becomes more
significant for the obtained values of h but it was less for the values
of g.
Abstract: This paper presents the experimental results of a
single cylinder Enfield engine using an electronically controlled fuel
injection system which was developed to carry out exhaustive tests
using neat CNG, and mixtures of hydrogen in compressed natural gas
(HCNG) as 0, 5, 10, 15 and 20% by energy. Experiments were
performed at 2000 and 2400 rpm with wide open throttle and varying
the equivalence ratio. Hydrogen which has fast burning rate, when
added to compressed natural gas, enhances its flame propagation rate.
The emissions of HC, CO, decreased with increasing percentage of
hydrogen but NOx was found to increase. The results indicated a
marked improvement in the brake thermal efficiency with the
increase in percentage of hydrogen added. The improved thermal
efficiency was clearly observed to be more in lean region as
compared to rich region. This study is expected to reduce vehicular
emissions along with increase in thermal efficiency and thus help in
reduction of further environmental degradation.
Abstract: The benefits of rooftop greenery systems (such as
energy savings, reduction of greenhouse gas emission for mitigating
climate change and maintaining sustainable development, indoor
temperature control etc.) in buildings are well recognized, however
there remains very little research conducted for quantifying the
benefits in subtropical climates such as in Australia. This study
mainly focuses on measuring/determining temperature profile and air
conditioning energy savings by implementing rooftop greenery
systems in subtropical Central Queensland in Australia. An
experimental set-up was installed at Rockhampton campus of Central
Queensland University, where two standard shipping containers (6m
x 2.4m x 2.4m) were converted into small offices, one with green
roof and one without. These were used for temperature, humidity and
energy consumption data collection. The study found that an energy
savings of up to 11.70% and temperature difference of up to 4°C can
be achieved in March in subtropical Central Queensland climate in
Australia. It is expected that more energy can be saved in peak
summer days (December/February) as temperature difference
between green roof and non-green roof is higher in December-
February.
Abstract: PCCI engines can reduce NOx and PM emissions
simultaneously without sacrificing thermal efficiency, but a low
combustion temperature resulting from early fuel injection, and
ignition occurring prior to TDC, can cause higher THC and CO
emissions and fuel consumption. In conclusion, it was found that the
PCCI combustion achieved by the 2-stage injection strategy with
optimized calibration factors (e.g. EGR rate, injection pressure, swirl
ratio, intake pressure, injection timing) can reduce NOx and PM
emissions simultaneously. This research works are expected to
provide valuable information conducive to a development of an
innovative combustion engine that can fulfill upcoming stringent
emission standards.
Abstract: Chlorine is one of the most abundant elements in
nature, which undergoes a complex biogeochemical cycle. Chlorine
bound in some substances is partly responsible for atmospheric ozone
depletion and contamination of some ecosystems. As due to
international regulations anthropogenic burden of volatile
organochlorines (VOCls) in atmosphere decreases, natural sources
(plants, soil, abiotic formation) are expected to dominate VOCl
production in the near future. Examples of plant VOCl production are
methyl chloride, and bromide emission from (sub)tropical ferns,
chloroform, 1,1,1-trichloroethane and tetrachloromethane emission
from temperate forest fern and moss. Temperate forests are found to
emit in addition to the previous compounds tetrachloroethene, and
brominated volatile compounds. VOCls can be taken up and further
metabolized in plants. The aim of this work is to identify and
quantitatively analyze the formed VOCls in temperate forest
ecosystems by a cryofocusing/GC-ECD detection method, hence
filling a gap of knowledge in the biogeochemical cycle of chlorine.
Abstract: Small cracks or chips of a product appear very
frequently in the course of continuous production of an automatic
press process system. These phenomena become the cause of not only
defective product but also damage of a press mold. In order to solve
this problem AE system was introduced. AE system was expected to
be very effective to real time detection of the defective product and to
prevention of the damage of the press molds.
In this study, for pick and analysis of AE signals generated from the
press process, AE sensors/pre-amplifier/analysis and processing board
were used as frequently found in the other similar cases. For analysis
and processing the AE signals picked in real time from the good or bad
products, specialized software called cdm8 was used. As a result of
this work it was conformed that intensity and shape of the various AE
signals differ depending on the weight and thickness of metal sheet
and process type.
Abstract: Wood pyrolysis for Casuarina glauca, Casuarina cunninghamiana, Eucalyptus camaldulensis, Eucalyptus microtheca was made at 450°C with 2.5°C/min. in a flowing N2-atmosphere. The Eucalyptus genus wood gave higher values of specific gravity, ash , total extractives, lignin, N2-liquid trap distillate (NLTD) and water trap distillate (WSP) than those for Casuarina genus. The GHC of NLTD was higher for Casuarina genus than that for Eucalyptus genus with the highest value for Casuarina cunninghamiana. Guiacol, 4-ethyl-2-methoxyphenol and syringol were observed in the NLTD of all the four wood species reflecting their parent hardwood lignin origin. Eucalyptus camaldulensis wood had the highest lignin content (28.89%) and was pyrolyzed to the highest values of phenolics (73.01%), guaiacol (11.2%) and syringol (32.28%) contents in methylene chloride fraction (MCF) of NLTD. Accordingly, recoveries of syringol and guaiacol may become economically attractive from Eucalyptus camaldulensis.
Abstract: Hydrogenated biodiesel is one of the most promising
renewable fuels. It has many advantages over conventional biodiesel,
including higher cetane number, higher heating value, lower
viscosity, and lower corrosiveness due to its absence of oxygen.
From previous work, Pd/TiO2 gave high conversion and selectivity in
hydrogenated biodiesel. In this work, the effect of biomass feedstocks
(i.e. beef fat, chicken fat, pork fat, and jatropha oil) on the production
of hydrogenated biodiesel over Pd/TiO2 has been studied. Biomass
feedstocks were analyzed by ICP-OES (inductively coupled plasma
optical emission spectrometry) to identify the content of impurities
(i.e. P, K, Ca, Na, and Mg). The deoxygenation catalyst, Pd/TiO2,
was prepared by incipient wetness impregnation (IWI) and tested in a
continuous flow packed-bed reactor at 500 psig, 325°C, H2/feed
molar ratio of 30, and LHSV of 4 h-1 for its catalytic activity and
selectivity in hydrodeoxygenation. All feedstocks gave high
selectivity in diesel specification range hydrocarbons and the main
hydrocarbons were n-pentadecane (n-C15) and n-heptadecane (n-
C17), resulting from the decarbonylation/decarboxylation reaction.
Intermediates such as oleic acid, stearic acid, palmitic acid, and esters
were also detected in minor amount. The conversion of triglycerides
in jatropha oil is higher than those of chicken fat, pork fat, and beef
fat, respectively. The higher concentration of metal impurities in
feedstock, the lower conversion of feedstock.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: The use of wind energy for electricity generation is
growing rapidly across the world and in Portugal. However, the
geographical characteristics of the country along with the average
wind regime and with the environmental restrictions imposed to these
projects create limitations to the exploit of the onshore wind
resource. The best onshore wind spots are already committed and the
possibility of offshore wind farms in the Portuguese cost is now
being considered. This paper aims to make a contribution to the
evaluation of offshore wind power projects in Portugal. The technical
restrictions are addressed and the strategic, environmental and
financial interest of the project is analysed from the private company
and public points of view. The results suggest that additional support
schemes are required to ensure private investors interest for these
projects. Assuming an approach of direct substitution of energy
sources for electricity generation, the avoided CO2 equivalent
emissions for an offshore wind power project were quantified. Based
on the conclusions, future research is proposed to address the
environmental and social impacts of these projects.
Abstract: The mixture formation prior to the ignition process
plays as a key element in the diesel combustion. Parametric studies of
mixture formation and ignition process in various injection parameter
has received considerable attention in potential for reducing
emissions. Purpose of this study is to clarify the effects of injection
pressure on mixture formation and ignition especially during ignition
delay period, which have to be significantly influences throughout the
combustion process and exhaust emissions. This study investigated
the effects of injection pressure on diesel combustion fundamentally
using rapid compression machine. The detail behavior of mixture
formation during ignition delay period was investigated using the
schlieren photography system with a high speed camera. This method
can capture spray evaporation, spray interference, mixture formation
and flame development clearly with real images. Ignition process and
flame development were investigated by direct photography method
using a light sensitive high-speed color digital video camera. The
injection pressure and air motion are important variable that strongly
affect to the fuel evaporation, endothermic and prolysis process
during ignition delay. An increased injection pressure makes spray tip
penetration longer and promotes a greater amount of fuel-air mixing
occurs during ignition delay. A greater quantity of fuel prepared
during ignition delay period thus predominantly promotes more rapid
heat release.
Abstract: In this paper, an automated algorithm to estimate and remove the continuous baseline from measured spectra containing both continuous and discontinuous bands is proposed. The algorithm uses previous information contained in a Continuous Database Spectra (CDBS) to obtain a linear basis, with minimum number of sampled vectors, capable of representing a continuous baseline. The proposed algorithm was tested by using a CDBS of flame spectra where Principal Components Analysis and Non-negative Matrix Factorization were used to obtain linear bases. Thus, the radical emissions of natural gas, oil and bio-oil flames spectra at different combustion conditions were obtained. In order to validate the performance in the baseline estimation process, the Goodness-of-fit Coefficient and the Root Mean-squared Error quality metrics were evaluated between the estimated and the real spectra in absence of discontinuous emission. The achieved results make the proposed method a key element in the development of automatic monitoring processes strategies involving discontinuous spectral bands.
Abstract: A long-term campaign for monitoring the
concentration of atmospheric Particulate Matter (PM) was conducted
at multiple sites located in the center and suburbs of the Tokyo
Metropolitan Area in Japan. The concentration of fine PM has shown a
declining trend over the last two decades. A positive matrix
factorization model elucidated that the contribution of combustion
sources was drastically reduced. In Japan, the regulations on vehicle
exhaust emissions were phased in and gradually tightened over the last
two decades, which has triggered a notable reduction in PM emissions
from automobiles and has contributed to the mitigation of the problem
of fine PM pollution.
Abstract: The Long-range Energy and Alternatives Planning (LEAP) energy planning system has been developed for South Africa, for the 2005 base year and a limited number of plausible future scenarios that may have significant implications (negative or positive) in terms of environmental impacts. The system quantifies the national energy demand for the domestic, commercial, transport, industry and agriculture sectors, the supply of electricity and liquid fuels, and the resulting emissions. The South African National Energy Research Institute (SANERI) identified the need to develop an environmental assessment tool, based on the LEAP energy planning system, to provide decision-makers and stakeholders with the necessary understanding of the environmental impacts associated with different energy scenarios. A comprehensive analysis of indicators that are used internationally and in South Africa was done and the available data was accessed to select a reasonable number of indicators that could be utilized in energy planning. A consultative process was followed to determine the needs of different stakeholders on the required indicators and also the most suitable form of reporting. This paper demonstrates the application of Energy Environmental Sustainability Indicators (EESIs) as part of the developed tool, which assists with the identification of the environmental consequences of energy generation and use scenarios and thereby promotes sustainability, since environmental considerations can then be integrated into the preparation and adoption of policies, plans, programs and projects. Recommendations are made to refine the tool further for South Africa.
Abstract: The main purpose of this research is the calculation of implicit prices of the environmental level of air quality in the city of Moscow on the basis of housing property prices. The database used contains records of approximately 20 thousand apartments and has been provided by a leading real estate agency operating in Russia. The explanatory variables include physical characteristics of the houses, environmental (industry emissions), neighbourhood sociodemographic and geographic data: GPS coordinates of each house. The hedonic regression results for ecological variables show «negative» prices while increasing the level of air contamination from such substances as carbon monoxide, nitrogen dioxide, sulphur dioxide, and particles (CO, NO2, SO2, TSP). The marginal willingness to pay for higher environmental quality is presented for linear and log-log models.
Abstract: The rapidly increasing costs of power line extensions
and fossil fuel, combined with the desire to reduce carbon dioxide
emissions pushed the development of hybrid power system suited for
remote locations, the purpose in mind being that of autonomous local
power systems. The paper presents the suggested solution for a “high
penetration" hybrid power system, it being determined by the
location of the settlement and its “zero policy" on carbon dioxide
emissions. The paper focuses on the technical solution and the power
flow management algorithm of the system, taking into consideration
local conditions of development.
Abstract: Electronic nose (array of chemical sensors) are widely
used in food industry and pollution control. Also it could be used to
locate or detect the direction of the source of emission odors. Usually
this task is performed by electronic nose (ENose) cooperated with
mobile vehicles, but when a source is instantaneous or surrounding is
hard for vehicles to reach, problem occurs. Thus a method for
stationary ENose to detect the direction of the source and locate the
source will be required. A novel method which uses the ratio between
the responses of different sensors as a discriminant to determine the
direction of source in natural wind surroundings is presented in this
paper. The result shows that the method is accurate and easily to be
implemented. This method could be also used in movably, as an
optimized algorithm for robot tracking source location.
Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: Breast carcinoma is the most common form of cancer
in women. Multicolour fluorescent in-situ hybridisation (m-FISH) is
a common method for staging breast carcinoma. The interpretation
of m-FISH images is complicated due to two effects: (i) Spectral
overlap in the emission spectra of fluorochrome marked DNA probes
and (ii) tissue autofluorescence. In this paper hyper-spectral images of
m-FISH samples are used and spectral unmixing is applied to produce
false colour images with higher contrast and better information
content than standard RGB images. The spectral unmixing is realised
by combinations of: Orthogonal Projection Analysis (OPA), Alterating
Least Squares (ALS), Simple-to-use Interactive Self-Modeling
Mixture Analysis (SIMPLISMA) and VARIMAX. These are applied
on the data to reduce tissue autofluorescence and resolve the spectral
overlap in the emission spectra. The results show that spectral unmixing
methods reduce the intensity caused by tissue autofluorescence by
up to 78% and enhance image contrast by algorithmically reducing
the overlap of the emission spectra.
Abstract: Environmental awareness and the recent
environmental policies have forced many electric utilities to
restructure their operational practices to account for their emission
impacts. One way to accomplish this is by reformulating the
traditional economic dispatch problem such that emission effects are
included in the mathematical model. This paper presents a Particle
Swarm Optimization (PSO) algorithm to solve the Economic-
Emission Dispatch problem (EED) which gained recent attention due
to the deregulation of the power industry and strict environmental
regulations. The problem is formulated as a multi-objective one with
two competing functions, namely economic cost and emission
functions, subject to different constraints. The inequality constraints
considered are the generating unit capacity limits while the equality
constraint is generation-demand balance. A novel equality constraint
handling mechanism is proposed in this paper. PSO algorithm is
tested on a 30-bus standard test system. Results obtained show that
PSO algorithm has a great potential in handling multi-objective
optimization problems and is capable of capturing Pareto optimal
solution set under different loading conditions.