Abstract: In the present study, a numerical approach to describe the pyrolysis of a single solid particle of wood is used to study the influence of various conditions such as particle size, heat transfer coefficient, reactor temperature and heating rate. The influence of these parameters in the change of the duration of the pyrolysis cycle was studied. Mathematical modeling was employed to simulate the heat, mass transfer, and kinetic processes inside the reactor. The evolutions of the mass loss as well as the evolution of temperature inside the thick piece are investigated numerically. The elaborated model was also employed to study the effect of the reactor temperature and the rate of heating on the change of the temperature and the local loss of the mass inside the piece of wood. The obtained results are in good agreement with the experimental data available in the literature.
Abstract: Fermentation is well known as an essential process to
develop chocolate flavor in dried cocoa beans. Besides developing
the precursor of cocoa flavor, it also induces the color changes in the
beans. The fermentation process is influenced by various factors such
as planting material, preconditioning of cocoa pod and fermentation
technique. Therefore, this study was conducted to evaluate color of
Malaysian cocoa beans and how the duration of pods storage and
fermentation technique using shallow box will effect on its color
characteristics. There are two factors being studied i.e. duration of
cocoa pod storage (0, 2, 4 and 6 days) and duration of cocoa
fermentation (0, 1, 2, 3, 4 and 5 days). The experiment is arranged in
4 x 6 factorial designs with 24 treatments and arrangement is in a
Completely Randomised Design (CRD). The produced beans are
inspected for color changes under artificial light during cut test and
divided into four groups of color namely fully brown, purple brown,
fully purple and slaty. Cut tests indicated that cocoa beans which are
directly dried without undergone fermentation has the highest slaty
percentage. However, application of pods storage before fermentation
process is found to decrease the slaty percentage. In contrast, the
percentages of fully brown beans start to dominate after two days of
fermentation, especially from four and six days of pods storage batch.
Whereas, almost all batches of cocoa beans have a percentage of fully
purple less than 20%. Interestingly, the percentage of purple brown
beans are scattered in the entire beans batch regardless any specific
trend. Meanwhile, statistical analysis using General Linear Model
showed that the pods storage has a significant effect on the color
characteristic of the Malaysian dried beans compared to fermentation
duration.
Abstract: Rapid developments in technology in the present age
have made it necessary for communities to follow technological
developments and adapt themselves to these developments. One of
the fields that are most rapidly affected by these developments is
undoubtedly education. Determination of the attitudes of preservice
teachers, who live in an age of technology and get ready to raise
future individuals, is of paramount importance both educationally and
professionally. The purpose of this study was to analyze attitudes of
preservice teachers towards technology and some variables that
predict these attitudes (gender, daily duration of internet use, and the
number of technical devices owned). 329 preservice teachers
attending the education faculty of a large university in central Turkey
participated, on a volunteer basis, in this study, where relational
survey model was used as the research method. Research findings
reveal that preservice teachers’ attitudes towards technology are
positive and at the same time, the attitudes of male preservice
teachers towards technology are more positive than their female
counterparts. As a result of the stepwise multiple regression analysis
where factors predicting preservice teachers’ attitudes towards
technology, it was found that duration of daily internet use was the
strongest predictor of attitudes towards technology.
Abstract: Online measurement of the product quality is a
challenging task in cement production, especially in the production of
Celitement, a novel environmentally friendly hydraulic binder. The
mineralogy and chemical composition of clinker in ordinary Portland
cement production is measured by X-ray diffraction (XRD) and
X-ray fluorescence (XRF), where only crystalline constituents can be
detected. But only a small part of the Celitement components can be
measured via XRD, because most constituents have an amorphous
structure. This paper describes the development of algorithms
suitable for an on-line monitoring of the final processing step of
Celitement based on NIR-data. For calibration intermediate products
were dried at different temperatures and ground for variable
durations. The products were analyzed using XRD and
thermogravimetric analyses together with NIR-spectroscopy to
investigate the dependency between the drying and the milling
processes on one and the NIR-signal on the other side. As a result,
different characteristic parameters have been defined. A short
overview of the Celitement process and the challenging tasks of the
online measurement and evaluation of the product quality will be
presented. Subsequently, methods for systematic development of
near-infrared calibration models and the determination of the final
calibration model will be introduced. The application of the model on
experimental data illustrates that NIR-spectroscopy allows for a quick
and sufficiently exact determination of crucial process parameters.
Abstract: This study investigated the effects of thermal
treatment on Tualang honey sample in terms of honey colour and
heat-induced small metabolites. The heating process was carried out
in a temperature controlled water batch at 90oC for 4 hours. The
honey samples were put in cylinder tubes with the dimension of 1 cm
diameter and 10 cm length for homogenous heat transfer. The results
found that the thermal treatment produced not only
hydroxylmethylfurfural, but also other harmful substances such as
phthalic anhydride and radiolytic byproducts. The degradation of
honey protein was due to the detection of free amino acids such as
cysteine and phenylalanine in heat-treated honey samples. Sugar
dehydration was also occurred because fragmented di-galactose was
identified based on the presence of characteristic ions in the mass
fragmentation pattern. The honey colour was found getting darker as
the heating duration was increased up to 4 hours. Approximately, 60
mm PFund of increment was noticed for the honey colour with the
colour change rate of 14.8 mm PFund per hour. Based on the
principal component analysis, the score plot clearly shows that the
chemical profile of Tualang honey was significantly altered after 2
hours of heating at 90oC.
Abstract: When evaluating the capacity of a generation park to
cover the load in transmission systems, traditional Loss of Load
Expectation (LOLE) and Expected Energy not Served (EENS)
indices can be used. If those indices allow computing the annual
duration and severity of load non covering situations, they do not take
into account the fact that the load excess is generally shifted from one
penury state (hour or quarter of an hour) to the following one. In this
paper, a sequential Monte Carlo framework is introduced in order to
compute adjusted LOLE and EENS indices. Practically, those
adapted indices permit to consider the effect of load excess transfer
on the global adequacy of a generation park, providing thus a more
accurate evaluation of this quantity.
Abstract: We have studied the temporal characteristics of
bistable perception of the stimuli of two types: one involves
alterations in a perceived depth and another one has an ambiguous
content. We used the Necker lattice and lines of shadowed circles
ambiguously perceived either as spheres or holes as stimuli of the
first type. The Winson figure (the Eskimo/Indian picture) was a
stimulus of the second type. We have analyzed how often the
reversals occurred (reversal rate) and for how long each of the two
interpretations, or percepts, was observed during one presentation
(stability durations). For all three ambiguous images the reversal rate
and the stability durations had similar values, which provide another
evidence for a significant role of top-down processes in multistable
perception.
Abstract: This research aimed to investigate the relationship
between attitude towards marketing mix, brand image and consumer
behavior of the passengers of low-cost airlines service. This study
employed by quantitative research and the questionnaire was used to
collect the data from 400 sampled of the passengers who have ever
used the low-cost airline services based in Bangkok, Thailand. The
descriptive statistics and Pearson’s correlation analysis were used to
analyze data. The research results revealed that the attitude of the marketing mix
of the low-cost airline services including product, price, place,
promotion and process had related to the consumer behavior on the
aspects of duration of service and frequency of service. While, the
brand image of the low cost airline including the characteristics of
organization, service quality and company identity had related to the
consumer behavior on duration of service, frequency of service and
cost of service at the significant statistically acceptable levels.
Abstract: This study aims to examine the sensory quality of
meatballs made from Balinese beef and buffalo meat after the
addition of smoke powder prior to storage at the temperatures of 2-
5°C for 7 days. This study used meat from Longissimus dorsi muscle
of male Balinese cattle aged 3 years and of male buffalo aged 5 years
as the main raw materials, and smoke powder as a binder and
preservative in making meatballs. The study was based on completely
randomized design (CRD) of factorial pattern of 2 x 3 x 2 where
factors 1, 2 and 3 included the types of meat (cattle and buffalo),
types of smoke powder (oven dried, freeze dried and spray dried)
with a level of 2% of the weight of the meat (w/w), and storage
duration (0 and 7 days) with three replications, respectively. The
parameters measured were the meatball sensory quality (scores of
tenderness, firmness, chewing residue, and intensity of flavor). The
results of this study show that each type of meat has produced
different sensory characteristics. The meatballs made from buffalo
meat have higher tenderness and elasticity scores than the Balinese
beef. Meanwhile, the buffalo meatballs have a lower residue
mastication score than the Balinese beef. Each type of smoke
powders has produced a relatively similar sensory quality of
meatballs. It can be concluded that the smoke powder of 2% of the
weight of the meat (w/w) could maintain the sensory quality of the
meatballs for 7 days of storage.
Abstract: Background: Breast milk may impact early brain
development, with potentially important biological, medical and
social implications. There is an important discussion on which is the
adequate breastfeeding extension to the development consolidation
and how the children breastfeeding affects their psychomotor
development, in the first year of life, and in following periods as
well. Some special fats (LC PUFA) contained in breast milk play a
key role in the brain’s maturation and cognitive development or
social skills. These capacities created during breastfeeding time
would be unfolded throughout all lifespan. Aim of the study: In our research, we have studied the effect of
breastfeeding in preschooler's psychomotor assessment.
Method: This study was conducted in a sample of 158 preschool
children in Vlorë, Albania. We have measured the psychometric
parameters of preschoolers with ASQ-3 (Age&Stage Questionnaires-
3). The studied sample was divided in three groups according to their
breastfeeding duration (3, 6 and 12 months). Results: Children breastfed for only 3 months have definitely
lower psychometric scores compared to the ones with 6 or more
months of breastfeeding (respectively 217 to 239 ASQ-3 scores). Six
and twelvemonth breastfed children have progressively more odds to
have high levels of psychomotor development comparing to those
with only 3 months of breastfeeding. The most affected psychometric
domains by shortness of breastfeeding are Communication and
Global motor. Conclusion: This leads to conclusion that to ensure high
psychomotor parameters during childhood is necessary breastfeeding
for at least 6 months.
Abstract: Lateral Geniculate Nucleus (LGN) is the relay center
in the visual pathway as it receives most of the input information
from retinal ganglion cells (RGC) and sends to visual cortex. Low
threshold calcium currents (IT) at the membrane are the unique
indicator to characterize this firing functionality of the LGN neurons
gained by the RGC input. According to the LGN functional
requirements such as functional mapping of RGC to LGN, the
morphologies of the LGN neurons were developed. During the
neurological disorders like glaucoma, the mapping between RGC and
LGN is disconnected and hence stimulating LGN electrically using
deep brain electrodes can restore the functionalities of LGN. A
computational model was developed for simulating the LGN neurons
with three predominant morphologies each representing different
functional mapping of RGC to LGN. The firings of action potentials
at LGN neuron due to IT were characterized by varying the
stimulation parameters, morphological parameters and orientation. A
wide range of stimulation parameters (stimulus amplitude, duration
and frequency) represents the various strengths of the electrical
stimulation with different morphological parameters (soma size,
dendrites size and structure). The orientation (0-1800) of LGN
neuron with respect to the stimulating electrode represents the angle
at which the extracellular deep brain stimulation towards LGN
neuron is performed. A reduced dendrite structure was used in the
model using Bush–Sejnowski algorithm to decrease the
computational time while conserving its input resistance and total
surface area. The major finding is that an input potential of 0.4 V is
required to produce the action potential in the LGN neuron which is
placed at 100 μm distance from the electrode. From this study, it can
be concluded that the neuroprostheses under design would need to
consider the capability of inducing at least 0.4V to produce action
potentials in LGN.
Abstract: Concurrent planning of project scheduling and
material ordering can provide more flexibility to the project
scheduling problem, as the project execution costs can be enhanced.
Hence, the issue has been taken into account in this paper. To do so, a
mixed-integer mathematical model is developed which considers the
aforementioned flexibility, in addition to the materials quantity
discount and space availability restrictions. Moreover, the activities
duration has been treated as decision variables. Finally, the efficiency
of the proposed model is tested by different instances. Additionally,
the influence of the aforementioned parameters is investigated on the
model performance.
Abstract: Green concrete are generally composed of recycling
materials as hundred or partial percent substitutes for aggregate,
cement, and admixture in concrete. To reduce greenhouse gas
emissions, efforts are needed to develop environmentally friendly
construction materials. Using of fly ash based geopolymer as an
alternative binder can help reduce CO2 emission of concrete. The
binder of geopolymer concrete is different from the ordinary Portland
cement concrete. Geopolymer Concrete specimens were prepared
with different concentration of NaOH solution M10, M14, and, M16
and cured at 60ºC in duration of 24 hours and 8 hours, in addition to
the curing in direct sunlight. Thus, it is necessary to study the effects
of the geopolymer binder on the behavior of concrete. Concrete is
made by using geopolymer technology is environmental friendly and
could be considered as part of the sustainable development. In this
study, the Local Alkaline Activator in Egypt and crashed stone as
coarse aggregate in fly ash based-geopolymer concrete was
investigated. This paper illustrates the development of mechanical
properties. Since the gained compressive strength for geopolymer
concrete at 28 days was in the range of 22.5MPa – 43.9MPa.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: This investigation is focused on using of Mon dance
in Pathum Thani Province’s tradition and has the following
objectives: 1) to study the background of Mon dance in Pathum
Thani Province; 2) to study Mon dance in Pathum Thani Province;
and 3) to study of using Mon dance in Pathum Thani province’s
tradition. This qualitative research was conducted in Pathum Thani
province (in the central of Thailand). Data was collected from
documentary study and field data by means of observation, interview,
and group discussion. Workshops were also held with a total of 100
attendees, comprised of 20 key informants, 40 casual informants and
40 general informants. Data was validated using the triangulation
technique and the findings are presented using the descriptive
analysis. The results of the study show that the historical background
of Mon dance in Pathum Thani Province initiated during the war
evacuation from Martaban (south of Burma) to settle down in Sam
Khok, Pathum Thani Province in Ayutthaya period to Rattanakosin.
The study found that Mon dance typically consists of 12-13 dancing
process. The melodies have 12-13 songs. Piphat Mon (Mon
traditional music ensemble) is used in the performance. Performers
are dressed in Mon traditional costumes. The performers are 6-12
women and depending on the employer’s demands. Length of the
performance varies from the duration of music orchestration. Rituals
and customs performed are paying homage to teachers before the
performance. The offerings are composed of flowers, incense sticks,
candles, money gifts which are well arranged on a tray with pedestal,
and also liquors, tobaccos and pure water for asking propitiousness.
For the use of Mon dance in Pathum Thani Province’s tradition, it is
found that the dance is commonly performed in the funeral
ceremonial tradition at present because the physical postures of the
performance are considered graceful and exquisite. In addition, as for
its value, it has long been believed since the ancient times that Mon
dance was a sacred thing considered as the dignity and glorification
especially for funeral ceremonies of priest or royal hierarchy classes.
However, Mon dance has continued to be used in the traditions
associated with Mon people activities in Pathum Thani Province for
instance customary welcome for honor guest and Songkran festival.
Abstract: The UK is leading in online retail and mobile
adoption. However, there is a dearth of information relating to mobile
apparel retail, and developing an understanding about consumer
browsing and purchase behaviour in m-retail channel would provide
apparel marketers, mobile website and app developers with the
necessary understanding of consumers’ needs. Despite the rapid
growth of mobile retail businesses, no published study has examined
shopping behaviour on fashion mobile apps and websites. A mixed method approach helped to understand why fashion
consumers prefer websites on smartphones, when diverse mobile
apps are also available. The following research methods were
employed: survey, eye-tracking experiments, observation, and
interview with retrospective think aloud. The mobile gaze tracking
device by SensoMotoric Instruments was used to understand
frustrations in navigation and other issues facing consumers in
mobile channel. This method helped to validate and compliment
other traditional user-testing approaches in order to optimize user
experience and enhance the development of mobile retail channel.
The study involved eight participants - females aged 18 to 35 years
old, who are existing mobile shoppers. The participants used the
Topshop mobile app and website on a smart phone to complete a task
according to a specified scenario leading to a purchase. The
comparative study was based on: duration and time spent at different
stages of the shopping journey, number of steps involved and product
pages visited, search approaches used, layout and visual clues, as
well as consumer perceptions and expectations. The results from the data analysis show significant differences in
consumer behaviour when using a mobile app or website on a smart
phone. Moreover, two types of problems were identified, namely
technical issues and human errors. Having a mobile app does not
guarantee success in satisfying mobile fashion consumers. The
differences in the layout and visual clues seem to influence the
overall shopping experience on a smart phone. The layout of search
results on the website was different from the mobile app. Therefore,
participants, in most cases, behaved differently on different
platforms. The number of product pages visited on the mobile app
was triple the number visited on the website due to a limited visibility
of products in the search results. Although, the data on traffic trends
held by retailers to date, including retail sector breakdowns for visits
and views, data on device splits and duration, might seem a valuable
source of information, it cannot explain why consumers visit many
product pages, stay longer on the website or mobile app, or abandon
the basket. A comprehensive list of pros and cons was developed by
highlighting issues for website and mobile app, and recommendations
provided. The findings suggest that fashion retailers need to be aware of
actual consumers’ behaviour on the mobile channel and their expectations in order to offer a seamless shopping experience. Added
to which is the challenge of retaining existing and acquiring new
customers. There seem to be differences in the way fashion
consumers search and shop on mobile, which need to be explored in
further studies.
Abstract: This study, tries to suggest a design method based on
displacement using finite difference numerical modeling in
reinforcing soil retaining wall with steel strip. In this case, dynamic
loading characteristics such as duration, frequency, peak ground
acceleration, geometrical characteristics of reinforced soil structure
and type of the site are considered to correct the pseudo static method
and finally introduce the pseudo static coefficient as a function of
seismic performance level and peak ground acceleration. For this
purpose, the influence of dynamic loading characteristics,
reinforcement length, height of reinforced system and type of the site
are investigated on seismic behavior of reinforcing soil retaining wall
with steel strip. Numerical results illustrate that the seismic response
of this type of wall is highly dependent to cumulative absolute
velocity, maximum acceleration, and height and reinforcement length
so that the reinforcement length can be introduced as the main factor
in shape of failure. Considering the loading parameters, geometric parameters of the
wall and type of the site showed that the used method in this study
leads to efficient designs in comparison with other methods, which
are usually based on limit-equilibrium concept. The outputs show the
over-estimation of equilibrium design methods in comparison with
proposed displacement based methods here.
Abstract: The photovoltaic (PV) panel with no galvanic
isolation system is well known technique in the world which is
effective and delivers power with enhanced efficiency. The PV
generation presented here is for stand-alone system installed in
remote areas when as the resulting power gets connected to electronic
load installation instead of being tied to the grid. Though very small,
even then transformer-less topology is shown to be with leakage in
pico-ampere range. By using PWM technique PWM, leakage current
in different situations is shown. The results shown in this paper show
how the pico-ampere current is reduced to femto-ampere through use
of inductors and capacitors of suitable values of inductor and
capacitors with the load.
Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: Research has shown that techno-entrepreneurship is
economically significant. Therefore, it is suggested that teaching
techno-entrepreneurship may be important because such programmes
would prepare current and future generations of learners to recognise
and act on high-technology opportunities. Education in technoentrepreneurship
may increase the knowledge of how to start one’s
own enterprise and recognise the technological opportunities for
commercialisation to improve decision-making about starting a new
venture; also it influence decisions about capturing the business
opportunities and turning them into successful ventures. Universities
can play a main role in connecting and networking technoentrepreneurship
students towards a cooperative attitude with real
business practice and industry knowledge. To investigate and answer
whether education for techno-entrepreneurs really helps, this paper
choses a comparison of literature reviews as its method of research.
After reviewing literature related to the impact of technoentrepreneurship
education on self-employment 6 studies which had
similar aim and objective to this paper were. These particular papers
were selected based on a keywords search and as their aim,
objectives, and gaps were close to the current research. In addition,
they were all based on the influence of techno-entrepreneurship
education in self-employment and intention of students to start new
ventures. The findings showed that teaching techno-entrepreneurship
education may have an influence on students’ intention and their
future self-employment, but which courses should be covered and the
duration of programmes, needs further investigation.