Abstract: The importance of happiness understanding research is caused by cardinal changes experiences in system of people values in the post-Soviet countries territory. «The time of changes», which characterized with destruction of old values and not creativeness of new, stimulating experiences by the person of existential vacuum. The given research is actual not only in connection with sense formation, but also in connection with necessity creatively to adapt in integrative space. According to numerous works [1,2,3], we define happiness as the peak experience connected with satisfaction correlated system of needs, dependent on style of subject's coping behavior.
Abstract: A solar refrigeration system based on the adsorptiondesorption
phenomena is designed and analyzed. An annular tubular
generator filled with silica gel adsorbent and with a perforated inner
cylinder is integrated within a flat solar collector. The working fluid
in the refrigeration cycle is water. The thermodynamic analysis and
because of the temperature level that could be attained with a flat
solar collector it is required that the system operates under vacuum
conditions. In order to enhance the performance of the system and to
get uniform temperature in the silica gel and higher desorbed mass,
an apparatus for rotation of the generator is incorporated in the
system. Testing is carried out and measurements are taken on the
designed installation. The effect of rotation is checked on the
temperature distribution and on the performance of this machine and
compared to the flat solar collector with fixed generator.
Abstract: The use of electronic sensors in the electronics
industry has become increasingly popular over the past few years,
and it has become a high competition product. The frequency
adjustment process is regarded as one of the most important process
in the electronic sensor manufacturing process. Due to inaccuracies
in the frequency adjustment process, up to 80% waste can be caused
due to rework processes; therefore, this study aims to provide a
preliminary understanding of the role of parameters used in the
frequency adjustment process, and also make suggestions in order to
further improve performance. Four parameters are considered in this
study: air pressure, dispensing time, vacuum force, and the distance
between the needle tip and the product. A full factorial design for
experiment 2k was considered to determine those parameters that
significantly affect the accuracy of the frequency adjustment process,
where a deviation in the frequency after adjustment and the target
frequency is expected to be 0 kHz. The experiment was conducted on
two levels, using two replications and with five center-points added.
In total, 37 experiments were carried out. The results reveal that air
pressure and dispensing time significantly affect the frequency
adjustment process. The mathematical relationship between these
two parameters was formulated, and the optimal parameters for air
pressure and dispensing time were found to be 0.45 MPa and 458 ms,
respectively. The optimal parameters were examined by carrying out
a confirmation experiment in which an average deviation of 0.082
kHz was achieved.
Abstract: Since 2005, an SRF module of CESR type serves as the
accelerating cavity at the Taiwan Light Source in the National
Synchrotron Radiation Research Center. A 500-MHz niobium cavity
is immersed in liquid helium inside this SRF module. To reduce heat
load, the liquid helium vessel is thermally shielded by
liquid-nitrogen-cooled copper layer, and the beam chambers are also
anchored with pipes of the liquid nitrogen flow in middle of the liquid
helium vessel and the vacuum vessel. A strong correlation of the
movement of the cavity-s frequency tuner with the temperature
variation of parts cooled with liquid nitrogen was observed. A
previous study on a spare SRF module with the niobium cavity cooled
by liquid nitrogen instead of liquid helium, satisfactory suppression of
the thermal oscillation was achieved by attaching a temporary buffer
tank for the vented shielding nitrogen flow from the SRF module. In
this study, a home-made buffer tank is designed and integrated to the
spare SRF module with cavity cooled by liquid helium. Design,
construction, integration, and preliminary test results of this buffer
tank are presented.
Abstract: A series of Ti based shape memory alloys with
composition of Ti50Ni49Cr1, Ti50Ni47Cr3 and Ti50Ni45Cr5 were
developed by vacuum arc-melting under a purified argon atmosphere.
The histometric and corrosion evaluation of Ti-Ni-Cr shape memory
alloys have been considered in this research work. The alloys were
developed by vacuum arc melting and implanted subcutaneously in
rabbits for 4, 8 and 12 weeks. Metallic implants were embedded in
order to determine the outcome of implantation on histometric and
corrosion evaluation of Ti-Ni-Cr metallic strips. Encapsulating
membrane formation around the alloys was minimal in the case of all
materials. After histomorphometric analyses it was possible to
demonstrate that there were no statistically significant differences
between the materials. Corrosion rate was also determined in this
study which is within acceptable range. The results showed the Ti-
Ni-Cr alloy was neither cytotoxic, nor have any systemic reaction on
living system in any of the test performed. Implantation shows good
compatibility and a potential of being used directly in vivo system.
Abstract: Martensitic stainless steels have been extensively used for their good corrosion resistance and better mechanical properties. Heat treatment was suggested as one of the most excellent ways to this regard; hence, it affects the microstructure, mechanical and corrosion properties of the steel. In the current research work the microstructural changes and corrosion behavior in an AISI 420A stainless steel exposed to temperatures in the 980-1035oC range were investigated. The heat treatment is carried out in vacuum furnace within the said temperature range. The quenching of the samples was carried out in oil, brine and water media. The formation and stability of passive film was studied by Open Circuit Potential, Potentiodynamic polarization and Electrochemical Scratch Tests. The Electrochemical Impedance Spectroscopy results simulated with Equivalent Electrical Circuit suggested bilayer structure of outer porous and inner barrier oxide films. The quantitative data showed thick inner barrier oxide film retarded electrochemical reactions. Micrographs of the quenched samples showed sigma and chromium carbide phases which prove the corrosion resistance of steel alloy.
Abstract: Experiments with pumpkin-rowanberry marmalade
candies were carried out at the Faculty of Food Technology of the
Latvia University of Agriculture. The objective of this investigation
was to evaluate the quality changes of pumpkin-rowanberry
marmalade candies packed in different packaging materials during
the storage of 15 weeks, and to find the most suitable packaging
material for prolongation of low sugar marmalade candies shelf-life.
An active packaging in combination with modified atmosphere
(MAP, CO2 100%) was examined and compared with traditional
packaging in air ambiance. Polymer Multibarrier 60 and paper bags
were used. Influence of iron based oxygen absorber in sachets of 500
cc obtained from Mitsubishi Gas Chemical Europe Ageless® on the
marmalade candies’ quality was tested during shelf life. Samples of
80±5 g were packaged in polymer pouches (110 mm x 110 mm),
hermetically sealed by MULTIVAC C300 vacuum chamber machine,
and stored in a room temperature +21±0.5 °C. The physiochemical
properties –moisture content, hardness, aw, pH, changes of
atmosphere content (CO2 and O2), ascorbic acid, total carotenoids,
total phenols in headspace of packs, and microbial conditions were
analysed before packaging and in the 1st, 3rd , 5th, 8th, 11th and 15th
weeks of storage.
Abstract: The voltage/current characteristics and the effect of
NO2 gas on the electrical conductivity of a PbPc gas sensor array is
investigated. The gas sensor is manufactured using vacuum
deposition of gold electrodes on sapphire substrate with the leadphathalocyanine
vacuum sublimed on the top of the gold electrodes.
Two versions of the PbPc gas sensor array are investigated. The
tested types differ in the gap sizes between the deposited gold
electrodes. The sensors are tested at different temperatures to account
for conductivity changes as the molecular adsorption/desorption rate
is affected by heat. The obtained results found to be encouraging as
the sensors shoed stability and sensitivity towards low concentration
of applied NO2 gas.
Abstract: The nonlinear damping behavior is usually ignored in
the design of a miniature moving-coil loudspeaker. But when the
loudspeaker operated in air, the damping parameter varies with the
voice-coil displacement corresponding due to viscous air flow. The
present paper presents an identification model as inverse problem to
identify the nonlinear damping parameter in the lumped parameter
model for the loudspeaker. Theoretical results for the nonlinear
damping are verified by using laser displacement measurement
scanner. These results indicate that the damping parameter has the
greatly different nonlinearity between in air and vacuum. It is believed
that the results of the present work can be applied in diagnosis and
sound quality improvement of a miniature loudspeaker.
Abstract: The research object was apple-black currant
marmalade candies. Experiments were carried out at the Faculty of
Food Technology of the Latvia University of Agriculture. An active
packaging in combination with modified atmosphere (MAP, CO2
100%) was examined and compared with traditional packaging in air
ambiance. Polymer Multibarrier 60 and paper bags were used.
Influence of iron based oxygen absorber in sachets of 500 cc
obtained from Mitsubishi Gas Chemical Europe Ageless® was tested
on the quality during the shelf of marmalade. Samples of 80±5 g
were packaged in polymer pouches (110 mm x 110 mm),
hermetically sealed by MULTIVAC C300 vacuum chamber machine,
and stored in room temperature +20.0±1.0 °C. The physiochemical
properties – weight losses, moisture content, hardness, aw, pH, colour,
changes of atmosphere content (CO2 and O2) in headspace of packs,
and microbial conditions were analysed before packaging and in the
1st, 3rd , 5th, 8th, 11th and 15th weeks of storage.
Abstract: Plasma Wind Tunnels (PWT) are extensively used for screening and qualification of re-entry Thermel Protection System (TPS) materials. Proper design of a supersonic diffuser for plasma wind tunnel is of importance for achieving good pressurerecovery (thereby reducing vacuum pumping requirement & run time costs) and isolating downstream stream fluctuations from propagating costs) and isolating downstream stream fluctuationnts the details of a rapid design methodology successfully employed for designing supersonic diffuser for high power (several megawatts)plasma wind tunnels and numerical performance analysis of a diffuser configuration designed for one megawatt power rated plasma wind tunnel(enthalpy ~ 30 MJ/kg) using FLUENT 6.3® solver for different diffuser operating sub-atmospheric back-pressures.
Abstract: Water contains oxygen which may make a human
breathe under water like a fish. Centrifugal separator can separate
dissolved gases from water. Carrier solution can increase the
separation of dissolved oxygen from water. But, to develop an
breathing device for a human under water, the enhancement of
separation of dissolved gases including oxygen and portable devices
which have dc battery based device and proper size are needed.
In this study, we set up experimental device for analyzing
separation characteristics of dissolved gases including oxygen from
water using a battery based portable vacuum pump. We characterized
vacuum state, flow rate of separation of dissolved gases and oxygen
concentration which were influenced by the manufactured vacuum
pump.
Abstract: The effect of chemical treatment in CdCl2 and thermal
annealing in 400°C, on the defect structures of potentially useful
ZnS\CdS solar cell thin films deposited onto quartz substrate and
prepared by vacuum deposition method was studied using the
Thermoluminesence (TL) techniques. A series of electron and hole
traps are found in the various deposited samples studied. After
annealing, however, it was observed that the intensity and activation
energy of TL signal increases with loss of the low temperature
electron traps.
Abstract: Vickers indentation is used to measure the hardness
of materials. In this study, numerical simulation of Vickers
indentation experiment was performed for Diamond like Carbon
(DLC) coated materials. DLC coatings were deposited on stainless
steel 304 substrates with Chromium buffer layer using RF Magnetron
and T-shape Filtered Cathodic Vacuum Arc Dual system The
objective of this research is to understand the elastic plastic
properties, stress strain distribution, ring and lateral crack growth and
propagation, penetration depth of indenter and delamination of
coating from substrate with effect of buffer layer thickness. The
effect of Poisson-s ratio of DLC coating was also analyzed. Indenter
penetration is more in coated materials with thin buffer layer as
compared to thicker one, under same conditions. Similarly, the
specimens with thinner buffer layer failed quickly due to high
residual stress as compared to the coated materials with reasonable
thickness of 200nm buffer layer. The simulation results suggested the
optimized thickness of 200 nm among the prepared specimens for
durable and long service.
Abstract: Attachment of the circulating monocytes to the
endothelium is the earliest detectable events during formation of
atherosclerosis. The adhesion molecules, chemokines and matrix
proteases genes were identified to be expressed in atherogenesis.
Expressions of these genes may influence structural integrity of the
luminal endothelium. The aim of this study is to relate changes in the
ultrastructural morphology of the aortic luminal surface and gene
expressions of the endothelial surface, chemokine and MMP-12 in
normal and hypercholesterolemic rabbits. Luminal endothelial
surface from rabbit aortic tissue was examined by scanning electron
microscopy (SEM) using low vacuum mode to ascertain
ultrastructural changes in development of atherosclerotic lesion. Gene
expression of adhesion molecules, MCP-1 and MMP-12 were studied
by Real-time PCR. Ultrastructural observations of the aortic luminal
surface exhibited changes from normal regular smooth intact
endothelium to irregular luminal surface including marked globular
appearance and ruptures of the membrane layer. Real-time PCR
demonstrated differentially expressed of studied genes in
atherosclerotic tissues. The appearance of ultrastructural changes in
aortic tissue of hypercholesterolemic rabbits is suggested to have
relation with underlying changes of endothelial surface molecules,
chemokine and MMP-12 gene expressions.
Abstract: This paper presents the fundamentals of Origami engineering and its application in nowadays as well as future industry. Several main cores of mathematical approaches such as Huzita- Hatori axioms, Maekawa and Kawasaki-s theorems are introduced briefly. Meanwhile flaps and circle packing by Robert Lang is explained to make understood the underlying principles in designing crease pattern. Rigid origami and its corrugation patterns which are potentially applicable for creating transformable or temporary spaces is discussed to show the transition of origami from paper to thick material. Moreover, some innovative applications of origami such as eyeglass, origami stent and high tech origami based on mentioned theories and principles are showcased in section III; while some updated origami technology such as Vacuumatics, self-folding of polymer sheets and programmable matter folding which could greatlyenhance origami structureare demonstrated in Section IV to offer more insight in future origami.
Abstract: Thermal water hammer is a special type of water
hammer which rarely occurs in heat exchangers. In biphasic fluids, if
steam bubbles are surrounded by condensate, regarding lower
condensate temperature than steam, they will suddenly collapse. As a
result, the vacuum caused by an extreme change in volume lead to
movement of the condensates in all directions and their collision the
force produced by this collision leads to a severe stress in the pipe
wall. This phenomenon is a special type of water hammer. According
to fluid mechanics, this phenomenon is a particular type of transient
flows during which abrupt change of fluid leads to sudden pressure
change inside the tube. In this paper, the mechanism of abrupt failure
of 80 tubes of 481 tubes of a methanol heat exchanger is discussed.
Initially, due to excessive temperature differences between heat
transfer fluids and simultaneous failure of 80 tubes, thermal shock
was presupposed as the reason of failure. Deeper investigation on
cross-section of failed tubes showed that failure was, ductile type of
failure, so the first hypothesis was rejected. Further analysis and more
accurate experiments revealed that failure of tubes caused by thermal
water hammer. Finally, the causes of thermal water hammer and
various solutions to avoid such mechanism are discussed.
Abstract: Wood as a natural renewable material is vulnerable to
degradation by microorganisms and susceptible to change in
dimension by water. In order to effectively improve the durability of
wood, an active reagent, maleic anhydride (Man) was selected for
wood modification. Man was first dissolved into a solvent, and then
penetrated into wood porous structure under a vacuum/pressure
condition. After a final catalyst-thermal treatment, wood modification
was finished. The test results indicate that acetone is a good solvent for
transporting Man into wood matrix. SEM observation proved that
wood samples treated by Man kept a good cellular structure, indicating
a well penetration of Man into wood cell walls. FTIR analysis
suggested that Man reacted with hydroxyl groups on wood cell walls
by its ring-ether group, resulting in reduction of amount of hydroxyl
groups and resultant good dimensional stability as well as fine decay
resistance. Consequently, Man modifying wood to improve its
durability is an effective method.
Abstract: In present work, drying characteristics of fresh papaya (Carica papaya L.) was studied to understand the dehydration process and its behavior. Drying experiments were carried out by a laboratory scaled microwave-vacuum oven. The parameters affecting drying characteristics including operating modes (continuous, pulsed), microwave power (400 and 800 W), and vacuum pressure (20, 30, and 40 cmHg) were investigated. For pulsed mode, two levels of power-off time (60 and 120 s) were used while the power-on time was fixed at 60 s and the vacuum pressure was fixed at 40 cmHg. For both operating modes, the effects of drying conditions on drying time, drying rate, and effective diffusivity were investigated. The results showed high microwave power, high vacuum, and pulsed mode of 60 s-on/60 s-off favored drying rate as shown by the shorten drying time and increased effective diffusivity. The drying characteristics were then described by Page-s model, which showed a good agreement with experimental data.
Abstract: Decentralized eco-sanitation system is a promising and sustainable mode comparing to the century-old centralized conventional sanitation system. The decentralized concept relies on an environmentally and economically sound management of water, nutrient and energy fluxes. Source-separation systems for urban waste management collect different solid waste and wastewater streams separately to facilitate the recovery of valuable resources from wastewater (energy, nutrients). A resource recovery centre constituted for 20,000 people will act as the functional unit for the treatment of urban waste of a high-density population community, like Singapore. The decentralized system includes urine treatment, faeces and food waste co-digestion, and horticultural waste and organic fraction of municipal solid waste treatment in composting plants. A design model is developed to estimate the input and output in terms of materials and energy. The inputs of urine (yellow water, YW) and faeces (brown water, BW) are calculated by considering the daily mean production of urine and faeces by humans and the water consumption of no-mix vacuum toilet (0.2 and 1 L flushing water for urine and faeces, respectively). The food waste (FW) production is estimated to be 150 g wet weight/person/day. The YW is collected and discharged by gravity into tank. It was found that two days are required for urine hydrolysis and struvite precipitation. The maximum nitrogen (N) and phosphorus (P) recovery are 150-266 kg/day and 20-70 kg/day, respectively. In contrast, BW and FW are mixed for co-digestion in a thermophilic acidification tank and later a decentralized/centralized methanogenic reactor is used for biogas production. It is determined that 6.16-15.67 m3/h methane is produced which is equivalent to 0.07-0.19 kWh/ca/day. The digestion residues are treated with horticultural waste and organic fraction of municipal waste in co-composting plants.