Abstract: The main objective of this research is to synthesize silk fibroin fiber for indoor air particulate removal. Silk cocoons were de-gummed using 0.5 wt % Na2CO3 alkaline solutions at 90 Ó╣ìC for 60 mins, washed with distilled water, and dried at 80 Ó╣ìC for 3 hrs in a vacuum oven. Two sets of experiment were conducted to investigate the impacts of initial particulate matter (PM) concentration and that of air flow rate on the removal efficiency. Rice bran collected from a local rice mill in Ubonratchathani province was used as indoor air contaminant in this work. The morphology and physical properties of silk fibroin (SF) fiber were measured. The SEM revealed the deposition of PM on the used fiber. The PM removal efficiencies of 72.29 ± 3.03 % and 39.33 ± 1.99 % were obtained of PM10 and PM2.5, respectively, when using the initial PM concentration at 0.040 mg/m3 and 0.020 mg/m3 of PM10 and PM2.5, respectively, with the air flow rate of 5 L/min.
Abstract: A measurement apparatus is designed and fabricated to
measure the effective thermal conductivity (keff) of a VIP (vacuum
insulation panel) core specimen under various vacuum states and
external loads. The apparatus consists of part for measuring keff, and
parts for controlling external load and vacuum condition. Uncertainty
of the apparatus is validated by measuring the standard reference
material and comparing with commercial devices with VIP samples.
Assessed uncertainty is maximum 2.5 % in case of the standard
reference material, 10 % in case of VIP samples. Using the apparatus,
keff of glass paper under various vacuum levels is examined.
Abstract: KSLV-I(Korea Space Launch Vehicle-I) is designed as
a launch vehicle to enter a 100 kg-class satellite to the LEO(Low Earth
Orbit). Attitude angles of the upper-stage, including roll, pitch and
yaw are controlled by the cold gas thruster system using nitrogen gas.
The cold gas thruster is an actuator in the RCS(Reaction Control
System). To design an attitude controller for the upper-stage, thrust
measurement in vacuum condition is required. In this paper, the new
thrust measurement system and calibration mechanism are developed
and measurement errors and signal processing method are presented.
Abstract: This study investigated the use of modified
atmosphere packaging (MAP) and different packaging to extend the
shelf life of Barbari flat bread. Three atmospheres including 70%CO2
and 30%N2, 50% CO2 and 50%N2 and a normal air as control were
used. The bread samples were packaged in three type pouches. The
shelf life was determined by appearance of mold and yeast (M +Y) in
Barbari bread samples stored at 25 ± 1°C and 38 ± 2% relative
humidity. The results showed that it is possible to prolong the shelf
life of Barbari bread from four days to about 21 days by using
modified atmosphere packaging with high carbon dioxide
concentration and high-barrier laminated and vacuum bags packages.
However, the hardness of samples kept in MAP increase significantly
by increase of carbon dioxide concentration. The correlation
coefficient (r) between headspace CO2 concentration and hardness
was 0.997, 0.997 and 0.599 for A, B and C packaging respectively.
High negative correlation coefficients were found between the crumb
moisture and the hardness values in various packaging. There were
significant negative correlation coefficients between sensory
parameters and hardness of texture.
Abstract: There has been a growing interest in utilizing surfactants in remediation processes to separate the hydrophobic volatile organic compounds (HVOCs) from aqueous solution. One attractive process is cloud point extraction (CPE), which utilizes nonionic surfactants as a separating agent. Since the surfactant cost is a key determination of the economic viability of the process, it is important that the surfactants are recycled and reused. This work aims to study the performance of the co-current vacuum stripping using a packed column for HVOCs removal from contaminated surfactant solution. Six types HVOCs are selected as contaminants. The studied surfactant is the branched secondary alcohol ethoxylates (AEs), Tergitol TMN-6 (C14H30O2). The volatility and the solubility of HVOCs in surfactant system are determined in terms of an apparent Henry’s law constant and a solubilization constant, respectively. Moreover, the HVOCs removal efficiency of vacuum stripping column is assessed in terms of percentage of HVOCs removal and the overall liquid phase volumetric mass transfer coefficient. The apparent Henry’s law constant of benzenz , toluene, and ethyl benzene were 7.00×10-5, 5.38×10-5, 3.35× 10-5 respectively. The solubilization constant of benzene, toluene, and ethyl benzene were 1.71, 2.68, 7.54 respectively. The HVOCs removal for all solute were around 90 percent.
Abstract: The electrical substation components are often subject to degradation due to over-voltage or over-current, caused by a short circuit or a lightning. A particular interest is given to the circuit breaker, regarding the importance of its function and its dangerous failure. This component degrades gradually due to the use, and it is also subject to the shock process resulted from the stress of isolating the fault when a short circuit occurs in the system. In this paper, based on failure mechanisms developments, the wear out of the circuit breaker contacts is modeled. The aim of this work is to evaluate its reliability and consequently its residual lifetime. The shock process is based on two random variables such as: the arrival of shocks and their magnitudes. The arrival of shocks was modeled using homogeneous Poisson process (HPP). By simulation, the dates of short-circuit arrivals were generated accompanied with their magnitudes. The same principle of simulation is applied to the amount of cumulative wear out contacts. The objective reached is to find the formulation of the wear function depending on the number of solicitations of the circuit breaker.
Abstract: Dill contains range of phytochemicals, such as vitamin C and polyphenols, which significantly contribute to their total antioxidant activity. The aim of the current research was to determine the best blanching method for processing of dill prior to microwave vacuum drying based on the content of phenolic compounds, vitamin C and free radical scavenging activity. Two blanching mediums were used – water and steam, and for part of the samples microwave pretreatment was additionally used. Evaluation of vitamin C, phenolic contents and scavenging of DPPH˙ radical in dried dill was performed. Blanching had an effect on all tested parameters and the blanching conditions are very important. After evaluation of the results, as the best method for dill pretreatment was established blanching at 90 °C for 30 seconds.
Abstract: Nowadays, desalination of salt water is considered an important industrial process. In many parts of the world, particularly in the gulf countries, the multi-stage flash (MSF) water desalination has an essential contribution in the production of fresh water. In this study, a simple mathematical model is defined to design a MSF desalination system and the feasibility of using the MSF desalination process in proximity of a 42 MW power plant is investigated. This power plant can just provide 10 ton/h superheated steam from low pressure (LP) section of heat recovery steam generator (HRSG) for thermal desalting system. The designed MSF system with gained output ratio (GOR) of 10.3 has 24 flashing stages and can produce 2480 ton/d of fresh water. The expected performance characteristics of the designed MSF desalination plant are determined. In addition, the effect of motive water pressure on the amount of non-condensable gases removed by water jet vacuum pumps is investigated.
Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.
Abstract: In this work, simulation algorithms for contact drying
of agitated particulate materials under vacuum and at atmospheric
pressure were developed. The implementation of algorithms gives a
predictive estimation of drying rate curves and bulk bed temperature
during contact drying. The calculations are based on the penetration
model to describe the drying process, where all process parameters
such as heat and mass transfer coefficients, effective bed properties,
gas and liquid phase properties are estimated with proper
correlations. Simulation results were compared with experimental
data from the literature. In both cases, simulation results were in good
agreement with experimental data. Few deviations were identified
and the limitations of the predictive capabilities of the models are
discussed. The programs give a good insight of the drying behaviour
of the analysed powders.
Abstract: Experiments have been carried out at the Latvia
University of Agriculture Department of Food Technology. The aim
of this work was to assess the effect of thermal treatment in flexible
retort pouch packaging on the quality of potatoes’ produce during the
storage time. Samples were evaluated immediately after retort
thermal treatment; and following 1; 2; 3 and 4 storage months at the
ambient temperature of +18±2ºC in vacuum packaging from
polyamide/polyethylene (PA/PE) and aluminum/polyethylene
(Al/PE) film pouches with barrier properties. Experimentally the
quality of the potatoes’ produce in dry butter and mushroom
dressings was characterized by measuring pH, hardness, color,
microbiological properties and sensory evaluation. The sterilization
was effective in protecting the produce from physical, chemical, and
microbial quality degradation. According to the study of obtained
data, it can be argued that the selected product processing technology
and packaging materials could be applied to provide the safety and
security during four-month storage period.
Abstract: The possibility of producing drinking water from
brackish ground water using Vacuum membrane distillation (VMD)
process was studied. It is a rising technology for seawater or brine
desalination process. The process simply consists of a flat sheet
hydrophobic micro porous PTFE membrane and diaphragm vacuum
pump without a condenser for the water recovery or trap. In this
work, VMD performance was investigated for aqueous NaCl solution
and natural ground water. The influence of operational parameters
such as feed flow rate (30 to 55 l/h), feed temperature (313 to 333 K),
feed salt concentration (5000 to 7000 mg/l) and permeate pressure
(1.5 to 6 kPa) on the membrane distillation (MD) permeation flux
have been investigated. The maximum flux reached to 28.34 kg/m2 h
at feed temperature, 333 K; vacuum pressure, 1.5 kPa; feed flow rate,
55 l/h and feed salt concentration, 7000 mg/l. The negligible effects
in the reduction of permeate flux found over 150 h experimental run
for salt water. But for the natural ground water application over 75 h,
scale deposits observed on the membrane surface and 29% reduction
in the permeate flux over 75 h. This reduction can be eliminated by
acidification of feed water. Hence, promote the research attention in
apply of VMD for the ground water purification over today-s
conventional RO operation.
Abstract: Vacuum membrane distillation (VMD) process can be
used for water purification or the desalination of salt water. The
process simply consists of a flat sheet hydrophobic micro porous
PTFE membrane and diaphragm vacuum pump without a condenser
for the water recovery or trap. The feed was used aqueous NaCl
solution. The VMD experiments were performed to evaluate the heat
and mass transfer coefficient of the boundary layer in a membrane
module. The only operating parameters are feed inlet temperature,
and feed flow rate were investigated. The permeate flux was strongly
affected by the feed inlet temperature, feed flow rate, and boundary
layer heat transfer coefficient. Since lowering the temperature
polarization coefficient is essential enhance the process performance
considerable and maximizing the heat transfer coefficient for
maximizes the mass flux of distillate water. In this paper, the results
of VMD experiments are used to measure the boundary layer heat
transfer coefficient, and the experimental results are used to reevaluate
the empirical constants in the Dittus- Boelter equation.
Abstract: The aim of present experiment was to evaluate the
influence of cultivar to quality parameters of dried potato chips and
sticks produced in microwave-vacuum drier. The potatoes before
drying were blanched in oil and water at 180ºC and at 85ºC
respectively. The moisture content, crispiness, the colour (CIE
L*a*b*), the content of ascorbic acid, total carotenoids and total fat
content of dried potato chips and sticks was determined The highest
ascorbic acid content, high content of carotenoids, low total fat
content, low acrylamide content and good crispiness (low breaking
force) especially for sticks was determined in the samples of Gundega
cultivar.
Abstract: The research object was wheat bread. Experiments
were carried out at the Faculty of Food Technology of the Latvia
University of Agriculture. An active packaging in combination with
modified atmosphere (MAP, CO2 60% and N2 40%) was examined
and compared with traditional packaging in air ambiance. Polymer
Multibarrier 60, PP and OPP bags were used. Influence of iron based
oxygen absorber in sachets of 100 cc obtained from Mitsubishi Gas
Chemical Europe Ageless® was tested on the quality during the shelf
of wheat bread. Samples of 40±4 g were packaged in polymer
pouches (110 mm x 120 mm), hermetically sealed by MULTIVAC
C300 vacuum chamber machine, and stored in room temperature
+21.0±0.5 °C. The physiochemical properties – weight losses,
moisture content, hardness, pH, colour, changes of atmosphere
content (CO2 and O2) in headspace of packs, and microbial
conditions were analysed before packaging and in the 7th, 14th, 21st
and 28th days of storage.
Abstract: The aim of the present work is to study the effect of annealing on the vibration damping capacity of high-chromium (16%) ferromagnetic steel. The alloys were prepared from raw materials of 99.9% purity melted in a high frequency induction furnace under high vacuum. The samples were heat-treated in vacuum at various temperatures (800 to 1200ºC) for 1 hour followed by slow cooling (120ºC/h). The inverted torsional pendulum method was used to evaluate the vibration damping capacity. The results indicated that the vibration damping capacity of the alloys is influenced by annealing and there exists a critical annealing temperature after 1000ºC. The damping capacity increases quickly below the critical temperature since the magnetic domains move more easily.
Abstract: The electrical and structural properties of Hf/Al/Ni/Au
(20/100/25/50 nm) ohmic contact to n-GaN are reported in this study.
Specific contact resistivities of Hf/Al/Ni/Au based contacts have been
investigated as a function of annealing temperature and achieve the
lowest value of 1.09´10-6 Ω·cm2 after annealing at 650 oC in vacuum.
A detailed mechanism of ohmic contact formation is discussed. By
using different chemical analyses, it is anticipated that the formation of
Hf-Al-N alloy might be responsible to form low temperature ohmic
contacts for the Hf-based scheme to n-GaN.
Abstract: If an unsteady heat transfer or heat impulse happens in
part of the cryogenic pipeline system of large space environment
simulation equipment while running in vacuum environment, it will
lead to abnormal flow of the cryogenic fluid in the pipeline. When the
situation gets worse, the cryogenic fluid in the pipeline will have phase
change and a gas block which results in the malfunction of the
cryogenic pipeline system. Referring to the structural parameter of a
typical cryogenic pipeline system and the basic equation, an analytical
model and a calculation model for cryogenic pipeline system can be
built. The various factors which influence the thermal resistance of a
cryogenic pipeline system can be analyzed and calculated by using the
qualitative analysis relation deduced for thermal resistance of pipeline.
The research conclusion could provide theoretical support for the
design and operation of a cryogenic pipeline system
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: In this article, a high vacuum system for the evaporation of organic semiconductors is introduced and a mathematical model is given. Based on the exact input output linearization a deposition rate controller is designed and tested with different evaporation materials.