Abstract: The application of ESS (Energy Storage Systems) in
the future grids has been the solution of the microgrid. However, high
investment costs necessitate accurate modeling and control strategy of
ESS to justify its economic viability and further underutilization.
Therefore, the reasonable control strategy for ESS which is subjected
to generator and usage helps to curtail the cost of investment and
operation costs. The rated frequency in power system is decreased
when the load is increasing unexpectedly; hence the thermal power is
operated at the capacity of only its 95% for the Governor Free (GF) to
adjust the frequency as reserve (5%) in practice. The ESS can be
utilized with governor at the same time for the frequency response due
to characteristic of its fast response speed and moreover, the cost of
ESS is declined rapidly to the reasonable price. This paper presents the
ESS control strategy to extend usage of the ESS taken account into
governor’s ramp rate and reduce the governor’s intervention as well.
All results in this paper are simulated by MATLAB.
Abstract: Broiler slaughter waste has become a major source of
pollution throughout the world. Utilization of broiler slaughter waste
by dry rendering process produced Rendered Chicken Oil (RCO), a
cheap raw material for biodiesel production and Carcass Meal a feed
ingredient for pets and fishes. Conversion of RCO into biodiesel may
open new vistas for generating wealth from waste besides controlling
the major havoc of environmental pollution. A two-step process to
convert RCO to good quality Biodiesel was invented. Acid catalysed
esterification of FFA followed by base catalysed transesterification of
triglycerides was carried out after meticulously standardizing the
methanol molar ratio, catalyst concentration, reaction temperature,
and reaction time to obtain the maximum biodiesel yield of 97.62%
and lowest glycerol yield of 6.96%. RCO biodiesel blend was tested
in a CRDI diesel engine. The results revealed that the blending of
commercial diesel with 20% RCO biodiesel (B20) lead to less engine
wear, a quieter engine and better fuel economy. The better lubricating
qualities of RCO B20 prevented over heating of engine, which
prolongs the engine life. RCO B20 can reduce the import of crude oil
and substantially reduce the engine emissions as proved by
significantly lower smoke levels, thus mitigating climatic changes.
Abstract: Revenue leakages are one of the major challenges
manufacturers face in production processes, as most of the input
materials that should emanate as products from the lines are lost as
waste. Rather than generating income from material input which is
meant to end-up as products, losses are further incurred as costs in
order to manage waste generated. In addition, due to the lack of a
clear view of the flow of resources on the lines from input to output
stage, acquiring information on the true cost of waste generated have
become a challenge. This has therefore given birth to the
conceptualization and implementation of waste minimization
strategies by several manufacturing industries. This paper reviews the
principles and applications of three environmental management
accounting tools namely Activity-based Costing (ABC), Life-Cycle
Assessment (LCA) and Material Flow Cost Accounting (MFCA) in
the manufacturing industry and their effectiveness in curbing revenue
leakages. The paper unveils the strengths and limitations of each of
the tools; beaming a searchlight on the tool that could allow for
optimal resource utilization, transparency in production process as
well as improved cost efficiency. Findings from this review reveal
that MFCA may offer superior advantages with regards to the
provision of more detailed information (both in physical and
monetary terms) on the flow of material inputs throughout the
production process compared to the other environmental accounting
tools. This paper therefore makes a case for the adoption of MFCA as
a viable technique for the identification and reduction of waste in
production processes, and also for effective decision making by
production managers, financial advisors and other relevant
stakeholders.
Abstract: The aim of the performed work is to establish the 2D
and 3D model of direct unsteady task of sample heat treatment by
moving source employing computer model on the basis of finite
element method. Complex boundary condition on heat loaded sample
surface is the essential feature of the task. Computer model describes
heat treatment of the sample during heat source movement over the
sample surface. It is started from 2D task of sample cross section as a
basic model. Possibilities of extension from 2D to 3D task are
discussed. The effect of the addition of third model dimension on
temperature distribution in the sample is showed. Comparison of
various model parameters on the sample temperatures is observed.
Influence of heat source motion on the depth of material heat
treatment is shown for several velocities of the movement. Presented
computer model is prepared for the utilization in laser treatment of
machine parts.
Abstract: A Mobile Adhoc Network (MANET) is a collection of mobile nodes that communicate with each other with wireless links and without pre-existing communication infrastructure. Routing is an important issue which impacts network performance. As MANETs lack central administration and prior organization, their security concerns are different from those of conventional networks. Wireless links make MANETs susceptible to attacks. This study proposes a new trust mechanism to mitigate wormhole attack in MANETs. Different optimization techniques find available optimal path from source to destination. This study extends trust and reputation to an improved link quality and channel utilization based Adhoc Ondemand Multipath Distance Vector (AOMDV). Differential Evolution (DE) is used for optimization.
Abstract: As a basic physiology need, threat to sufficient food
production is threat to human survival. Food security has been an
issue that has gained global concern. This paper looks at the food
security in Nigeria by assessing the availability of food and
accessibility of the available food. The paper employed multiple
linear regression technique and graphic trends of growth rates of
relevant variables to show the situation of food security in Nigeria.
Results of the tests revealed that population growth rate was higher
than the growth rate of food availability in Nigeria for the earlier
period of the study. Commercial bank credit to agricultural sector,
foreign exchange utilization for food and the Agricultural Credit
Guarantee Scheme Fund (ACGSF) contributed significantly to food
availability in Nigeria. Food prices grew at a faster rate than the
average income level, making it difficult to access sufficient food. It
implies that prior to the year 2012; there was insufficient food to feed
the Nigerian populace. However, continued credit to the food and
agricultural sector will ensure sustained and sufficient production of
food in Nigeria. Microfinance banks should make sufficient credit
available to smallholder farmer. Government should further control
and subsidize the rising price of food to make it more accessible by
the people.
Abstract: As a by-product of the biodiesel industries, glycerol
has been vastly generated which surpasses the market demand. It is
imperative to develop an efficient glycerol valorization processes in
minimizing the net energy requirement and intensifying the biodiesel
production. In this study, base-catalyzed transesterification of
glycerol with dimethyl carbonate using microwave irradiation as
heating method to produce glycerol carbonate was conducted by
varying grades of glycerol, i.e. 70%, 86% and 99% purity, that is
obtained from biodiesel plant. Metal oxide catalysts were used with
varying operating parameters including reaction time, DMC/glycerol
molar ratio, catalyst weight %, temperature and stirring speed. From
the study on the effect of different operating parameters it was found
that the type of catalyst used has the most significant effect on the
transesterification reaction. Amidst the metal oxide catalysts
examined, CaO gave the best performance. This study indicates the
feasibility of producing glycerol carbonate using different grade of
glycerol in both conventional thermal activation and microwave
irradiation with CaO as catalyst. Microwave assisted
transesterification (MAT) of glycerol into glycerol carbonate has
demonstrated itself as an energy efficient route by achieving 94.2%
yield of GC at 65°C, 5 minutes reaction time, 1 wt% CaO and
DMC/glycerol molar ratio of 2. The advantages of MAT
transesterification route has made the direct utilization of bioglycerol
from biodiesel production without the need of purification. This has
marked a more economical and less-energy intensive glycerol
carbonate synthesis route.
Abstract: Graphene was dispersed using a tip sonicator and the
effect of surfactants were analysed. Sodium Dodecyl Sulphate (SDS)
and Polyvinyl Alcohol (PVA) were compared to observe whether or
not they had any effect on any de-wrinkling, and secondly whether
they aided to achieve better dispersions. There is a huge demand for
wrinkle free graphene as this will greatly increase its usefulness in
various engineering applications. A comprehensive literature on dewrinkling
graphene has been discussed. Low magnification Scanning
Electronic Microscopy (SEM) was conducted to assess the quality of
graphene de-wrinkling. The utilization of the PVA has significant
effect on de-wrinkling whereas SDS had minimal effect on the dewrinkling
of graphene.
Abstract: Tannase (tannin acyl hydrolase, E.C.3.1.1.20) is an
important hydrolysable enzyme with innumerable applications and
industrial potential. In the present study, a kinetic model has been
developed for the batch fermentation used for the production of
tannase by A.flavus MTCC 3783. Maximum tannase activity of
143.30 U/ml was obtained at 96 hours under optimum operating
conditions at 35oC, an initial pH of 5.5 and with an inducer tannic
acid concentration of 3% (w/v) for a fermentation period of 120
hours. The biomass concentration reaches a maximum of 6.62 g/l at
96 hours and further there was no increase in biomass concentration
till the end of the fermentation. Various unstructured kinetic models
were analyzed to simulate the experimental values of microbial
growth, tannase activity and substrate concentration. The Logistic
model for microbial growth , Luedeking - Piret model for production
of tannase and Substrate utilization kinetic model for utilization of
substrate were capable of predicting the fermentation profile with
high coefficient of determination (R2) values of 0.980, 0.942 and
0.983 respectively. The results indicated that the unstructured models
were able to describe the fermentation kinetics more effectively.
Abstract: High Voltage Direct Current (HVDC) power
transmission is employed to move large amounts of electric power.
There are several possibilities to enhance the transient stability in a
power system. One adequate option is by using the high
controllability of the HVDC if HVDC is available in the system. This
paper presents a control technique for HVDC to enhance the transient
stability. The strategy controls the power through the HVDC to help
make the system more transient stable during disturbances. Loss of
synchronism is prevented by quickly producing sufficient
decelerating energy to counteract accelerating energy gained during.
In this study, the power flow in the HVDC link is modulated with the
addition of an auxiliary signal to the current reference of the rectifier
firing angle controller. This modulation control signal is derived from
speed deviation signal of the generator utilizing a PD controller; the
utilization of a PD controller is suitable because it has the property of
fast response. The effectiveness of the proposed controller is
demonstrated with a SMIB test system.
Abstract: Mustard leaves are rich in folates, vitamin A, K and
B-complex. Mustard greens are low in calories and fats and rich in
dietary fiber. They are rich in potassium, manganese, iron, copper,
calcium, magnesium and low in sodium. It is very rich in antioxidants
and Phytonutrients. For the optimization of process variables
(moisture content and mustard leave powder), the experiments were
conducted according to central composite Face Centered Composite
design of RSM. The mustard leaves powder was replaced with
composite flour (a combination of rice, chickpea and corn in the ratio
of 70:15:15). The extrudate was extruded in a twin screw extruder at
a barrel temperature of 120°C. The independent variables were
mustard leaves powder (2-10 %) and moisture content (12-20 %).
Responses analyzed were bulk density, water solubility index, water
absorption index, lateral expansion, antioxidant activity, total
phenolic content, and overall acceptability. The optimum conditions
obtained were 7.19 g mustard leaves powder in 100g premix having
16.8% moisture content (w.b).
Abstract: UAV’s are small remote operated or automated aerial
surveillance systems without a human pilot aboard. UAV’s generally
finds its use in military and special operation application, a recent
growing trend in UAV’s finds its application in several civil and nonmilitary
works such as inspection of power or pipelines. The
objective of this paper is the augmentation of a UAV in order to
replace the existing expensive sonar (Sound Navigation And
Ranging) based equipment amongst small scale fisherman, for whom
access to sonar equipment are restricted due to limited economic
resources. The surveillance equipment’s present in the UAV will
relay data and GPS (Global Positioning System) location onto a
receiver on the fishing boat using RF signals, using which the
location of the schools of fishes can be found. In addition to this, an
emergency beacon system is present for rescue operations and drone
recovery.
Abstract: A sensory network consists of multiple detection
locations called sensor nodes, each of which is tiny, featherweight
and portable. A single path routing protocols in wireless sensor
network can lead to holes in the network, since only the nodes
present in the single path is used for the data transmission. Apart
from the advantages like reduced computation, complexity and
resource utilization, there are some drawbacks like throughput,
increased traffic load and delay in data delivery. Therefore, multipath
routing protocols are preferred for WSN. Distributing the traffic
among multiple paths increases the network lifetime. We propose a
scheme, for the data to be transmitted through a dominant path to
save energy. In order to obtain a high delivery ratio, a basic route
reconstruction protocol is utilized to reconstruct the path whenever a
failure is detected. A basic reconstruction routing (BRR) algorithm is
proposed, in which a node can leap over path failure by using the
already existing routing information from its neighbourhood while
the composed data is transmitted from the source to the sink. In order
to save the energy and attain high data delivery ratio, data is
transmitted along a multiple path, which is achieved by BRR
algorithm whenever a failure is detected. Further, the analysis of
how the proposed protocol overcomes the drawback of the existing
protocols is presented. The performance of our protocol is compared
to AOMDV and energy efficient node-disjoint multipath routing
protocol (EENDMRP). The system is implemented using NS-2.34.
The simulation results show that the proposed protocol has high
delivery ratio with low energy consumption.
Abstract: Whey is the lactose rich by-product of the dairy
industry, having good amount of nutrient reservoir. Most abundant
nutrients are lactose, soluble proteins, lipids and mineral salts.
Disposing of whey by most of milk plants which do not have proper
pre-treatment system is the major issue. As a result of which, there
can be significant loss of potential food and energy source. Thus,
whey has been explored as the substrate for the synthesis of different
value added products such as enzymes. β-galactosidase is one of the
important enzymes and has become the major focus of research due
to its ability to catalyze both hydrolytic as well as
transgalactosylation reaction simultaneously. The enzyme is widely
used in dairy industry as it catalyzes the transformation of lactose to
glucose and galactose, making it suitable for the lactose intolerant
people. The enzyme is intracellular in both bacteria and yeast,
whereas for molds, it has an extracellular location. The present work
was carried to utilize the whey for the production of β-galactosidase
enzyme using both yeast and fungal cultures. The yeast isolate
Kluyveromyces marxianus WIG2 and various fungal strains have
been used in the present study. Different disruption techniques have
also been investigated for the extraction of the enzyme produced
intracellularly from yeast cells. Among the different methods tested
for the disruption of yeast cells, SDS-chloroform showed the
maximum β-galactosidase activity. In case of the tested fungal
cultures, Aureobasidium pullulans NCIM 1050 was observed to be
the maximum extracellular enzyme producer.
Abstract: Fast speed drives for Permanent Magnet Synchronous
Motor (PMSM) is a crucial performance for the electric traction
systems. In this paper, PMSM is derived with a Model-based
Predictive Control (MPC) technique. Fast speed tracking is achieved
through optimization of the DC source utilization using MPC. The
technique is based on predicting the optimum voltage vector applied
to the driver. Control technique is investigated by comparing to the
cascaded PI control based on Space Vector Pulse Width Modulation
(SVPWM). MPC and SVPWM-based FOC are implemented with the
TMS320F2812 DSP and its power driver circuits. The designed MPC
for a PMSM drive is experimentally validated on a laboratory test
bench. The performances are compared with those obtained by a
conventional PI-based system in order to highlight the improvements,
especially regarding speed tracking response.
Abstract: Among various active filters, shunt active filter is a
viable solution for reactive power and harmonics compensation. In
this paper, the SRF plan is used to generate current reference for
compensation and conventional PI controllers were used as the
controller to compensate the reactive power. The design of the closed
loop controllers is reserved simple by modeling them as first order
systems. Computationally uncomplicated and efficient SVM system
is used in the present work for better utilization of dc bus voltage.
The rating of shunt active filter has been finalized based on the
reactive power demand of the selected reactive load. The proposed
control and SVM technique are validated by simulating in MATLAB
software.
Abstract: The addition of lime as Ca(OH)2 to sewage sludge to
destroy pathogens (Escherichia coli), was evaluated also in relation
to heavy metal bioavailability.
The obtained results show that the use of calcium hydroxide at the
dose of 3% effectively destroyed pathogens ensuring the stability at
high pH values over long period and the duration of the sewage
sludge stabilization. In general, lime addition decreased the total
extractability of heavy metals indicating a reduced bioavailability of
these elements. This is particularly important for a safe utilization in
agricultural soils to reduce the possible transfer of heavy metals to
the food chain.
Abstract: This paper examines the utilization of public-private
partnerships for the building and operation of wastewater treatment
plants. Our research focuses on risk allocation in this kind of projects.
Our analysis builds on more than hundred wastewater treatment
plants built and operated through PPP projects in Aragon (Spain).
The paper illustrates the consequences of an inadequate management
of construction risk and an unsuitable transfer of demand risk in
wastewater treatment plants. It also shows that the involvement of
many public bodies at local, regional and national level further
increases the complexity of this kind of projects and make time
delays more likely.
Abstract: An efficient remanufacturing network lead to an
efficient design of sustainable manufacturing enterprise. In
remanufacturing network, products are collected from the customer
zone, disassembled and remanufactured at a suitable remanufacturing
facility. In this respect, another issue to consider is how the returned
product to be remanufactured, in other words, what is the best layout
for such facility. In order to achieve a sustainable manufacturing
system, Cellular Manufacturing System (CMS) designs are highly
recommended, CMSs combine high throughput rates of line layouts
with the flexibility offered by functional layouts (job shop).
Introducing the CMS while designing a remanufacturing network will
benefit the utilization of such a network. This paper presents and
analyzes a comprehensive mathematical model for the design of
Dynamic Cellular Remanufacturing Systems (DCRSs). In this paper,
the proposed model is the first one to date that considers CMS and
remanufacturing system simultaneously. The proposed DCRS model
considers several manufacturing attributes such as multi period
production planning, dynamic system reconfiguration, duplicate
machines, machine capacity, available time for workers, worker
assignments, and machine procurement, where the demand is totally
satisfied from a returned product. A numerical example is presented
to illustrate the proposed model.
Abstract: Present study is carried out on six lane divided urban
arterial road in Patna and Pune city of India. Both the road having
distinct differences in terms of the vehicle composition and the road
side parking. Arterial road in Patan city has 33% of non-motorized
mode, whereas Pune arterial road dominated by 65% of Two wheeler.
Also road side parking is observed in Patna city. The field studies
using videography techniques are carried out for traffic data
collection. Data are extracted for one minute duration for vehicle
composition, speed variation and flow rate on selected arterial road of
the two cities. Speed flow relationship is developed and capacity is
determine. Equivalency factor in terms of dynamic car unit is
determine to represent the vehicle is single unit. The variation in the
capacity due to side friction, presence of non motorized traffic and
effective utilization of lane width is compared at concluding remarks.