Abstract: In this paper, solution of fuzzy differential equation
under general differentiability is obtained by simulink. The simulink
solution is equivalent or very close to the exact solution of the
problem. Accuracy of the simulink solution to this problem is
qualitatively better. An illustrative numerical example is presented
for the proposed method.
Abstract: The automatic transmission (AT) is one of the most
important components of many automobile transmission systems. The
shift quality has a significant influence on the ride comfort of the
vehicle. During the AT shift process, the joint elements such as the
clutch and bands engage or disengage, linking sets of gears to create a
fixed gear ratio. Since these ratios differ between gears in a fixed gear
ratio transmission, the motion of the vehicle could change suddenly
during the shift process if the joint elements are engaged or disengaged
inappropriately, additionally impacting the entire transmission system
and increasing the temperature of connect elements.The objective was
to establish a system model for an AT powertrain using
Matlab/Simulink. This paper further analyses the effect of varying
hydraulic pressure and the associated impact on shift quality during
both engagment and disengagement of the joint elements, proving that
shift quality improvements could be achieved with appropriate
hydraulic pressure control.
Abstract: The Object of this paper is to design and analyze a
Hysteresis modulation based sliding mode control (HMSMC) for
positive output elementary super lift Luo converter (POESLLC),
which is the start-of-the-art DC-DC converter. The positive output
elementary super lift Luo converter performs the voltage
conversion from positive source voltage to positive load voltage.
This paper proposes a HMSMC capable of providing the good
steady state and dynamic performance compared to conventional
controllers. Dynamic equations describing the positive output
elementary super lift luo converter are derived by using state space
average method. The simulation model of the positive output
elementary super lift Luo converter with its control circuit is
implemented in Matlab/Simulink. The HMSMC for positive
output elementary super lift Luo converter is tested for line
changes, load changes and also for components variations.
Abstract: This paper deals with the application of artificial
neural network (ANN) and fuzzy based Adaptive Neuro Fuzzy
Inference System(ANFIS) approach to Load Frequency Control
(LFC) of multi unequal area hydro-thermal interconnected power
system. The proposed ANFIS controller combines the advantages of
fuzzy controller as well as quick response and adaptability nature of
ANN. Area-1 and area-2 consists of thermal reheat power plant
whereas area-3 and area-4 consists of hydro power plant with electric
governor. Performance evaluation is carried out by using intelligent
controller like ANFIS, ANN and Fuzzy controllers and conventional
PI and PID control approaches. To enhance the performance of
intelligent and conventional controller sliding surface is included.
The performances of the controllers are simulated using
MATLAB/SIMULINK package. A comparison of ANFIS, ANN,
Fuzzy, PI and PID based approaches shows the superiority of
proposed ANFIS over ANN & fuzzy, PI and PID controller for 1%
step load variation.
Abstract: This paper presents a fuzzy control system for a three degree of freedom (3-DOF) stabilized platform with explicit decoupling scheme. The system under consideration is a system with strong interactions between three channels. By using the concept of decentralized control, a control structure is developed that is composed of three control loops, each of which is associated with a single-variable fuzzy controller and a decoupling unit. Takagi-Sugeno (TS) fuzzy control algorithm is used to implement the fuzzy controller. The decoupling units design is based on the adaptive theory reasoning. Simulation tests were established using Simulink of Matlab. The obtained results have demonstrated the feasibility and effectiveness of the proposed approach. Simulation results are represented in this paper.
Abstract: An efficient transient flow simulation for gas
pipelines and networks is presented. The proposed transient flow
simulation is based on the transfer function models and MATLABSimulink.
The equivalent transfer functions of the nonlinear
governing equations are derived for different types of the boundary
conditions. Next, a MATLAB-Simulink library is developed and
proposed considering any boundary condition type. To verify the
accuracy and the computational efficiency of the proposed
simulation, the results obtained are compared with those of the
conventional finite difference schemes (such as TVD, method of
lines, and other finite difference implicit and explicit schemes). The
effects of the flow inertia and the pipeline inclination are
incorporated in this simulation. It is shown that the proposed
simulation has a sufficient accuracy and it is computationally more
efficient than the other methods.
Abstract: Electric vehicle (EV) is one of the effective solutions to
control emission of greenhouses gases in the world. It is of interest
for future transportation due to its sustainability and efficiency by
automotive manufacturers. Various electrical motors have been used
for propulsion system of electric vehicles in last decades. In this
paper brushed DC motor, Induction motor (IM), switched reluctance
motor (SRM) and brushless DC motor (BLDC) are simulated and
compared. BLDC motor is recommended for high performance
electric vehicles. PWM switching technique is implemented for speed
control of BLDC motor. Behavior of different modes of PWM speed
controller of BLDC motor are simulated in MATLAB/SIMULINK.
BLDC motor characteristics are compared and discussed for various
PWM switching modes under normal and inverter fault conditions.
Comparisons and discussions are verified through simulation results.
Abstract: Direct Torque Control is a control technique in AC
drive systems to obtain high performance torque control. The
conventional DTC drive contains a pair of hysteresis comparators.
DTC drives utilizing hysteresis comparators suffer from high torque
ripple and variable switching frequency. The most common solution
to those problems is to use the space vector depends on the reference
torque and flux. In this Paper The space vector modulation technique
(SVPWM) is applied to 2 level inverter control in the proposed
DTC-based induction motor drive system, thereby dramatically
reducing the torque ripple. Then the controller based on space vector
modulation is designed to be applied in the control of Induction
Motor (IM) with a three-level Inverter. This type of Inverter has
several advantages over the standard two-level VSI, such as a greater
number of levels in the output voltage waveforms, Lower dV/dt, less
harmonic distortion in voltage and current waveforms and lower
switching frequencies. This paper proposes a general SVPWM
algorithm for three-level based on standard two-level SVPWM. The
proposed scheme is described clearly and simulation results are
reported to demonstrate its effectiveness. The entire control scheme is
implemented with Matlab/Simulink.
Abstract: This paper focuses on a critical component of the situational awareness (SA), the neural control of depth flight of an autonomous underwater vehicle (AUV). Constant depth flight is a challenging but important task for AUVs to achieve high level of autonomy under adverse conditions. With the SA strategy, we proposed a multirate neural control of an AUV trajectory for a nontrivial mid-small size AUV “r2D4" stochastic model. This control system has been demonstrated and evaluated by simulation of diving maneuvers using software package Simulink. From the simulation results it can be seen that the chosen AUV model is stable in the presence of noises, and also can be concluded that the proposed research technique will be useful for fast SA of similar AUV systems in real-time search-and-rescue operations.
Abstract: Renewable energy resources are inexhaustible, clean as compared with conventional resources. Also, it is used to supply regions with no grid, no telephone lines, and often with difficult accessibility by common transport. Satellite earth stations which located in remote areas are the most important application of renewable energy. Neural control is a branch of the general field of intelligent control, which is based on the concept of artificial intelligence. This paper presents the mathematical modeling of satellite earth station power system which is required for simulating the system.Aswan is selected to be the site under consideration because it is a rich region with solar energy. The complete power system is simulated using MATLAB–SIMULINK.An artificial neural network (ANN) based model has been developed for the optimum operation of earth station power system. An ANN is trained using a back propagation with Levenberg–Marquardt algorithm. The best validation performance is obtained for minimum mean square error. The regression between the network output and the corresponding target is equal to 96% which means a high accuracy. Neural network controller architecture gives satisfactory results with small number of neurons, hence better in terms of memory and time are required for NNC implementation. The results indicate that the proposed control unit using ANN can be successfully used for controlling the satellite earth station power system.
Abstract: This paper presents a hybrid electric scooter model developed and simulated using Matlab/Simulink. This hybrid scooter modeled has a parallel hybrid structure. The main propulsion units consist of a two stroke internal combustion engine and a hub motor attached to the front wheel of the scooter. The methodology used to optimize the energy and fuel consumption of the hybrid electric scooter is the multi-mode approach. Various case studies were presented to check the model and were compared to the literatures. Results shown that the model developed was feasible and valuable.
Abstract: This paper focuses on developing an integrated
reliable and sophisticated model for ultra large wind turbines And to
study the performance and analysis of vector control on large wind
turbines. With the advance of power electronics technology, direct
driven multi-pole radial flux PMSG (Permanent Magnet Synchronous
Generator) has proven to be a good choice for wind turbines
manufacturers. To study the wind energy conversion systems, it is
important to develop a wind turbine simulator that is able to produce
realistic and validated conditions that occur in real ultra MW wind
turbines. Three different packages are used to simulate this model,
namely, Turbsim, FAST and Simulink. Turbsim is a Full field wind
simulator developed by National Renewable Energy Laboratory
(NREL). The wind turbine mechanical parts are modeled by FAST
(Fatigue, Aerodynamics, Structures and Turbulence) code which is
also developed by NREL. Simulink is used to model the PMSG, full
scale back to back IGBT converters, and the grid.
Abstract: The object of this paper is to design and analyze a
proportional – integral (PI) control for positive output elementary
super lift Luo converter (POESLLC), which is the start-of-the-art
DC-DC converter. The positive output elementary super lift Luo
converter performs the voltage conversion from positive source
voltage to positive load voltage. This paper proposes a
development of PI control capable of providing the good static and
dynamic performance compared to proportional – integralderivative
(PID) controller. Using state space average method
derives the dynamic equations describing the positive output
elementary super lift luo converter and PI control is designed. The
simulation model of the positive output elementary super lift Luo
converter with its control circuit is implemented in
Matlab/Simulink. The PI control for positive output elementary
super lift Luo converter is tested for transient region, line changes,
load changes, steady state region and also for components
variations.
Abstract: The design of Automatic Generation Control (AGC) system plays a vital role in automation of power system. This paper proposes Hybrid Neuro Fuzzy (HNF) approach for AGC of two-area interconnected reheat thermal power system with the consideration of Generation Rate Constraint (GRC). The advantage of proposed controller is that it can handle the system non-linearities and at the same time the proposed approach is faster than conventional controllers. The performance of HNF controller has been compared with that of both conventional Proportional Integral (PI) controller as well as Fuzzy Logic Controller (FLC) both in the absence and presence of Generation Rate Constraint (GRC). System performance is examined considering disturbance in each area of interconnected power system.
Abstract: Induction motors are being used in greater numbers
throughout a wide variety of industrial and commercial applications
because it provides many benefits and reliable device to convert the
electrical energy into mechanical motion. In some application it-s
desired to control the speed of the induction motor. Because of the
physics of the induction motor the preferred method of controlling its
speed is to vary the frequency of the AC voltage driving the motor. In
recent years, with the microcontroller incorporated into an appliance
it becomes possible to use it to generate the variable frequency AC
voltage to control the speed of the induction motor.
This study investigates the microcontroller based variable
frequency power inverter. the microcontroller is provide the variable
frequency pulse width modulation (PWM) signal that control the
applied voltage on the gate drive, which is provides the required
PWM frequency with less harmonics at the output of the power
inverter.
The fully controlled bridge voltage source inverter has been
implemented with semiconductors power devices isolated gate
bipolar transistor (IGBT), and the PWM technique has been
employed in this inverter to supply the motor with AC voltage.
The proposed drive system for three & single phase power inverter
is simulated using Matlab/Simulink. The Matlab Simulation Results
for the proposed system were achieved with different SPWM. From
the result a stable variable frequency inverter over wide range has
been obtained and a good agreement has been found between the
simulation and hardware of a microcontroller based single phase
inverter.
Abstract: This paper proposes the study of a robust control of
the doubly fed induction generator (DFIG) used in a wind energy
production. The proposed control is based on the linear active
disturbance rejection control (ADRC) and it is applied to the control
currents rotor of the DFIG, the DC bus voltage and active and
reactive power exchanged between the DFIG and the network. The
system under study and the proposed control are simulated using
MATLAB/SIMULINK.
Abstract: This paper will focus on modeling, analysis and simulation of a 42V/14V dc/dc converter based architecture. This architecture is considered to be technically a viable solution for automotive dual-voltage power system for passenger car in the near further. An interleaved dc/dc converter system is chosen for the automotive converter topology due to its advantages regarding filter reduction, dynamic response, and power management. Presented herein, is a model based on one kilowatt interleaved six-phase buck converter designed to operate in a Discontinuous Conduction Mode (DCM). The control strategy of the converter is based on a voltagemode- controlled Pulse Width Modulation (PWM) with a Proportional-Integral-Derivative (PID). The effectiveness of the interleaved step-down converter is verified through simulation results using control-oriented simulator, MatLab/Simulink.
Abstract: The Proton Exchange Membrane Fuel Cell (PEMFC)
control system has an important effect on operation of cell.
Traditional controllers couldn-t lead to acceptable responses because
of time- change, long- hysteresis, uncertainty, strong- coupling and
nonlinear characteristics of PEMFCs, so an intelligent or adaptive
controller is needed. In this paper a neural network predictive
controller have been designed to control the voltage of at the
presence of fluctuations of temperature. The results of
implementation of this designed NN Predictive controller on a
dynamic electrochemical model of a small size 5 KW, PEM fuel cell
have been simulated by MATLAB/SIMULINK.
Abstract: Pulse width modulation (PWM) techniques have been
the subject of intensive research for different industrial and power
sector applications. A large variety of methods, different in concept
and performance, have been newly developed and described. This
paper analyzes the comparative merits of Sinusoidal Pulse Width
Modulation (SPWM) and Space Vector Pulse Width Modulation
(SVPWM) techniques and the suitability of these techniques in a
Shunt Active Filter (SAF). The objective is to select the scheme that
offers effective utilization of DC bus voltage and also harmonic
reduction at the input side. The effectiveness of the PWM techniques
is tested in the SAF configuration with a non linear load. The
performance of the SAF with the SPWM and (SVPWM) techniques
are compared with respect to the THD in source current. The study
reveals that in the context of closed loop SAF control with the
SVPWM technique there is only a minor improvement in THD. The
utilization of the DC bus with SVPWM is also not significant
compared to that with SPWM because of the non sinusoidal
modulating signal from the controller in SAF configuration.
Abstract: In this paper we propose the study of a centrifugal pump control system driven by a three-phase induction motor, which is supplied by a PhotoVoltaic PV generator. The system includes solar panel, a DC / DC converter equipped with its MPPT control, a voltage inverter to three-phase Pulse Width Modulation - PWM and a centrifugal pump driven by a three phase induction motor. In order to control the flow of the centrifugal pump, a Direct Torque Control - DTC of the induction machine is used. To illustrate the performances of the control, simulation results are carried out using Matlab/Simulink.