Abstract: In the first part of the research work, an electrolyzer (10.16 cm dia and 24.13 cm height) to produce hydrogen and oxygen was constructed for single slice O2/H2 fuel cell using cation exchange membrane. The electrolyzer performance was tested with 23% NaOH, 30% NaOH, 30% KOH and 35% KOH electrolyte solution with current input 4 amp and 2.84 V from the rectifier. Rates of volume of hydrogen produced were 0.159 cm3/sec, 0.155 cm3/sec, 0.169 cm3/sec and 0.163 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution. Rates of volume of oxygen produced were 0.212 cm3/sec, 0.201 cm3/sec, 0.227 cm3/sec and 0.219 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution (1.5 L). In spite of being tested the increased concentration of electrolyte solution, the gas rate does not change significantly. Therefore, inexpensive 23% NaOH electrolyte solution was chosen to use as the electrolyte in the electrolyzer. In the second part of the research work, graphite serpentine flow plates, fiberglass end plates, stainless steel screen electrodes, silicone rubbers were made to assemble the single slice O2/H2 polymer electrolyte membrane fuel cell (PEMFC).
Abstract: The expansive nature of soils containing high
amounts of clay minerals can be altered through chemical
stabilization, resulting in a material suitable for construction
purposes. The primary objective of this investigation was to
study the changes induced in the molecular structure of
phosphoric acid stabilized bentonite and lateritic soil using
Nuclear Magnetic Resonance (NMR) and Fourier Transform
Infrared (FTIR) spectroscopy. Based on the obtained data, it
was found that a surface alteration mechanism was the main
reason responsible for the improvement of treated soils.
Furthermore, the results indicated that the Al present in the
octahedral layer of clay minerals were more amenable to
chemical attacks and also partly responsible for the formation
of new products.
Abstract: In this paper, we present an analytical framework for the evaluation of the uplink performance of multihop cellular networks based on dynamic time division duplex (TDD). New wireless broadband protocols, such as WiMAX, WiBro, and 3G-LTE apply TDD, and mobile communication protocols under standardization (e.g., IEEE802.16j) are investigating mobile multihop relay (MMR) as a future technology. In this paper a novel MMR TDD scheme is presented, where the dynamic range of the frame is shared to traffic resources of asymmetric nature and multihop relaying. The mobile communication channel interference model comprises of inner and co-channel interference (CCI). The performance analysis focuses on the uplink due to the fact that the effects of dynamic resource allocation show significant performance degradation only in the uplink compared to time division multiple access (TDMA) schemes due to CCI [1-3], where the downlink results to be the same or better.The analysis was based on the signal to interference power ratio (SIR) outage probability of dynamic TDD (D-TDD) and TDMA systems,which are the most widespread mobile communication multi-user control techniques. This paper presents the uplink SIR outage probability with multihop results and shows that the dynamic TDD scheme applying MMR can provide a performance improvement compared to single hop applications if executed properly.
Abstract: The paper proposes a way of parallel processing of
SURF and Optical Flow for moving object recognition and tracking.
The object recognition and tracking is one of the most important task
in computer vision, however disadvantage are many operations cause
processing speed slower so that it can-t do real-time object recognition
and tracking. The proposed method uses a typical way of feature
extraction SURF and moving object Optical Flow for reduce
disadvantage and real-time moving object recognition and tracking,
and parallel processing techniques for speed improvement. First
analyse that an image from DB and acquired through the camera using
SURF for compared to the same object recognition then set ROI
(Region of Interest) for tracking movement of feature points using
Optical Flow. Secondly, using Multi-Thread is for improved
processing speed and recognition by parallel processing. Finally,
performance is evaluated and verified efficiency of algorithm
throughout the experiment.
Abstract: In this study, we explore the use of information for inventory decision in the healthcare organization (HO). We consider the scenario when the HO can make use of the information collected from some correlated products to enhance its inventory planning. Motivated by our real world observations that HOs adopt RFID and bar-coding system for information collection purpose, we examine the effectiveness of these systems for inventory planning with Bayesian information updating. We derive the optimal ordering decision and study the issue of Pareto improvement in the supply chain. Our analysis demonstrates that RFID system will outperform the bar-coding system when the RFID system installation cost and the tag cost reduce to a level that is comparable with that of the barcoding system. We also show how an appropriately set wholesale pricing contract can achieve Pareto improvement in the HO supply chain.
Abstract: Four design alternatives for lateral force-resisting
systems of tall buildings in Dubai, UAE are presented. Quantitative
comparisons between the different designs are also made. This paper
is intended to provide different feasible lateral systems to be used in
Dubai in light of the available seismic hazard studies of the UAE.
The different lateral systems are chosen in conformance with the
International Building Code (IBC). Moreover, the expected behavior
of each system is highlighted and light is shed on some of the cost
implications associated with lateral system selection.
Abstract: The assessment of surface waters in Enugu metropolis
for fecal coliform bacteria was undertaken. Enugu urban was divided
into three areas (A1, A2 and A3), and fecal coliform bacteria
analysed in the surface waters found in these areas for four years
(2005-2008). The plate count method was used for the analyses. Data
generated were subjected to statistical tests involving; Normality test,
Homogeneity of variance test, correlation test, and tolerance limit
test. The influence of seasonality and pollution trends were
investigated using time series plots. Results from the tolerance limit
test at 95% coverage with 95% confidence, and with respect to EU
maximum permissible concentration show that the three areas suffer
from fecal coliform pollution. To this end, remediation procedure
involving the use of saw-dust extracts from three woods namely;
Chlorophora-Excelsa (C-Excelsa),Khayan-Senegalensis,(CSenegalensis)
and Erythrophylum-Ivorensis (E-Ivorensis) in
controlling the coliforms was studied. Results show that mixture of
the acetone extracts of the woods show the most effective
antibacterial inhibitory activities (26.00mm zone of inhibition)
against E-coli. Methanol extract mixture of the three woods gave best
inhibitory activity (26.00mm zone of inhibition) against S-areus, and
25.00mm zones of inhibition against E-Aerogenes. The aqueous
extracts mixture gave acceptable zones of inhibitions against the
three bacteria organisms.
Abstract: A current mirror (CM) based on self cascode MOSFETs low voltage analog and mixed mode structures has been proposed. The proposed CM has high output impedance and can operate at 0.5 V. P-Spice simulations confirm the high performance of this CM with a bandwidth of 6.0 GHz at input current of 100 μA.
Abstract: It is well known that Logistic Regression is the gold
standard method for predicting clinical outcome, especially
predicting risk of mortality. In this paper, the Decision Tree method
has been proposed to solve specific problems that commonly use
Logistic Regression as a solution. The Biochemistry and
Haematology Outcome Model (BHOM) dataset obtained from
Portsmouth NHS Hospital from 1 January to 31 December 2001 was
divided into four subsets. One subset of training data was used to
generate a model, and the model obtained was then applied to three
testing datasets. The performance of each model from both methods
was then compared using calibration (the χ2 test or chi-test) and
discrimination (area under ROC curve or c-index). The experiment
presented that both methods have reasonable results in the case of the
c-index. However, in some cases the calibration value (χ2) obtained
quite a high result. After conducting experiments and investigating
the advantages and disadvantages of each method, we can conclude
that Decision Trees can be seen as a worthy alternative to Logistic
Regression in the area of Data Mining.
Abstract: Over 90% of the world trade is carried by the
international shipping industry. As most of the countries are
developing, seaborne trade continues to expand to bring benefits for
consumers across the world. Studies show that world trade will
increase 70-80% through shipping in the next 15-20 years. Present
global fleet of 70000 commercial ships consumes approximately 200
million tonnes of diesel fuel a year and it is expected that it will be
around 350 million tonnes a year by 2020. It will increase the
demand for fuel and also increase the concentration of CO2 in the
atmosphere. So, it-s essential to control this massive fuel
consumption and CO2 emission. The idea is to utilize a diesel-wind
hybrid system for ship propulsion. Use of wind energy by installing
modern wing-sails in ships can drastically reduce the consumption of
diesel fuel. A huge amount of wind energy is available in oceans.
Whenever wind is available the wing-sails would be deployed and
the diesel engine would be throttled down and still the same forward
speed would be maintained. Wind direction in a particular shipping
route is not same throughout; it changes depending upon the global
wind pattern which depends on the latitude. So, the wing-sail
orientation should be such that it optimizes the use of wind energy.
We have made a computer programme in which by feeding the data
regarding wind velocity, wind direction, ship-motion direction; we
can find out the best wing-sail position and fuel saving for
commercial ships. We have calculated net fuel saving in certain
international shipping routes, for instance, from Mumbai in India to
Durban in South Africa. Our estimates show that about 8.3% diesel
fuel can be saved by utilizing the wind. We are also developing an
experimental model of the ship employing airfoils (small scale wingsail)
and going to test it in National Wind Tunnel Facility in IIT
Kanpur in order to develop a control mechanism for a system of
airfoils.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: Fracture process in mechanically loaded steel fiber
reinforced high-strength (SFRHSC) concrete is characterized by
fibers bridging the crack providing resistance to its opening.
Structural SFRHSC fracture model was created; material fracture
process was modeled, based on single fiber pull-out laws, which were
determined experimentally (for straight fibers, fibers with end hooks
(Dramix), and corrugated fibers (Tabix)) as well as obtained
numerically ( using FEM simulations). For this purpose experimental
program was realized and pull-out force versus pull-out fiber length
was obtained (for fibers embedded into concrete at different depth
and under different angle). Model predictions were validated by
15x15x60cm prisms 4 point bending tests. Fracture surfaces analysis
was realized for broken prisms with the goal to improve elaborated
model assumptions. Optimal SFRHSC structures were recognized.
Abstract: In the national and professional music of oral tradition
of many people in the East there is the metric formula called “ussuli",
that is to say rhythmic constructions of different character and a
composition. Ussuli in translation from Arabic means the law. The
cultural contacts of the ancient and medieval inhabitants of the
Central Asia, India, China, East Turkestan, Iraq, Afghanistan,
Turkey, and Iran have played a certain role in formation of both
musical and dancing heritage of each of these people. During
theatrical shows many dances were performed under the
accompaniment of percussion instruments as nagra, dayulpaz, doll.
The abovementioned tools are used as the obligatory accompanying
tool in an orchestra and at support of dancing acts as the solo tool.
Dynamics of development of a dancing composition, at times
execution of technique of movement depends on various
combinations of ussuli and their receptions of execution.
Abstract: Liposomal magnetofection is the most powerful nonviral method for the nucleic acid delivery into the cultured cancer cells and widely used for in vitro applications. Use of the static magnetic field condition may result in non-uniform distribution of aggregate complexes on the surface of cultured cells. To prevent this, we developed the new device which allows to concentrate aggregate complexes under dynamic magnetic field, assisting more contact of these complexes with cellular membrane and, possibly, stimulating endocytosis. Newly developed device for magnetofection under dynamic gradient magnetic field, “DynaFECTOR", was used to compare transfection efficiency of human liver hepatocellular carcinoma cell line HepG2 with that obtained by lipofection and magnetofection. The effect of two parameters on transfection efficiency, incubation time under dynamic magnetic field and rotation frequency of magnet, was estimated. Liposomal magnetofection under dynamic gradient magnetic field showed the highest transfection efficiency for HepG2 cells.
Abstract: Availability of high dimensional biological datasets such as from gene expression, proteomic, and metabolic experiments can be leveraged for the diagnosis and prognosis of diseases. Many classification methods in this area have been studied to predict disease states and separate between predefined classes such as patients with a special disease versus healthy controls. However, most of the existing research only focuses on a specific dataset. There is a lack of generic comparison between classifiers, which might provide a guideline for biologists or bioinformaticians to select the proper algorithm for new datasets. In this study, we compare the performance of popular classifiers, which are Support Vector Machine (SVM), Logistic Regression, k-Nearest Neighbor (k-NN), Naive Bayes, Decision Tree, and Random Forest based on mock datasets. We mimic common biological scenarios simulating various proportions of real discriminating biomarkers and different effect sizes thereof. The result shows that SVM performs quite stable and reaches a higher AUC compared to other methods. This may be explained due to the ability of SVM to minimize the probability of error. Moreover, Decision Tree with its good applicability for diagnosis and prognosis shows good performance in our experimental setup. Logistic Regression and Random Forest, however, strongly depend on the ratio of discriminators and perform better when having a higher number of discriminators.
Abstract: One of the essential requirements in order to have a
realistic surgical simulator is real-time interaction by means of a
haptic interface is. In fact, reproducing haptic sensations increases
the realism of the simulation. However, the interaction need to be
performed in real-time, since a delay between the user action and the
system reaction reduces the user immersion. In this paper, we present
a prototype of the coronary stent implant simulator developed in the
HERMES Project; this system allows real-time interactions with a
artery by means of a specific haptic device; thus the user can
interactively navigate in a reconstructed artery and force feedback is
produced when contact occurs between the artery walls and the
medical instruments
Abstract: Fourty one strains of ESBL producing P.aeruginosa
which were previously isolated from burn patients in Kerman
University general hospital, Iran were subjected to PCR, RFLP and
sequencing in order to determine the type of extended spectrum β-
lactamases (ESBL), the restriction digestion pattern and possibility of
mutation among detected genes. DNA extraction was carried out by
phenol chloroform method. PCR for detection of bla genes was
performed using specific primer for each gene. Restriction Fragment
Length Polymorphism (RFLP) for ESBL genes was carried out using
EcoRI, NheI, PVUII, EcoRV, DdeI, and PstI restriction enzymes. The
PCR products were subjected to direct sequencing of both the strands
for identification of the ESBL genes.The blaCTX-M, blaVEB-1, blaPER-1,
blaGES-1, blaOXA-1, blaOXA-4 and blaOXA-10 genes were detected in the
(n=1) 2.43%, (n=41)100%, (n=28) 68.3%, (n=10) 24.4%, (n=29)
70.7%, (n=7)17.1% and (n=38) 92.7% of the ESBL producing isolates
respectively. The RFLP analysis showed that each ESBL gene has
identical pattern of digestion among the isolated strains. Sequencing
of the ESBL genes confirmed the genuinety of PCR products and
revealed no mutation in the restriction sites of the above genes. From
results of the present investigation it can be concluded that blaVEB-1
and blaCTX-M were the most and the least frequently isolated ESBL
genes among the P.aeruginosa strains isolated from burn patients. The
RFLP and sequencing analysis revealed that same clone of the bla
genes were indeed existed among the antibiotic resistant strains.
Abstract: Motion estimation is the most computationally
intensive part in video processing. Many fast motion estimation
algorithms have been proposed to decrease the computational
complexity by reducing the number of candidate motion vectors.
However, these studies are for fast search algorithms themselves while
almost image and video compressions are operated with software
based. Therefore, the timing constraints for running these motion
estimation algorithms not only challenge for the video codec but also
overwhelm for some of processors. In this paper, the performance of
motion estimation is enhanced by using Intel's Streaming SIMD
Extension 2 (SSE2) technology with Intel Pentium 4 processor.
Abstract: In this paper, computational fluid dynamics (CFD) is utilized to characterize a prototype biolistic delivery system, the biomedical device based on the contoured-shock-tube design (CST), with the aim at investigating shocks induced flow instabilities within the contoured shock tube. The shock/interface interactions, the growth of perturbation at an interface between two fluids of different density are interrogated. The key features of the gas dynamics and gas-particle interaction are discussed
Abstract: Urban road network traffic has become one of the
most studied research topics in the last decades. This is mainly due to
the enlargement of the cities and the growing number of motor
vehicles traveling in this road network. One of the most sensitive
problems is to verify if the network is congestion-free. Another
related problem is the automatic reconfiguration of the network
without building new roads to alleviate congestions. These problems
require an accurate model of the traffic to determine the steady state
of the system. An alternative is to simulate the traffic to see if there
are congestions and when and where they occur. One key issue is to
find an adequate model for road intersections. Once the model
established, either a large scale model is built or the intersection is
represented by its performance measures and simulation for analysis.
In both cases, it is important to seek the queueing model to represent
the road intersection. In this paper, we propose to model the road
intersection as a BCMP queueing network and we compare this
analytical model against a simulation model for validation.