Abstract: In this research the effects of adding silica and
alumina nanoparticles on flow ability and compressive strength of
cementitious composites based on Portland cement were investigated.
In the first stage, the rheological behavior of different samples
containing nanosilica, nanoalumina and polypropylene, polyvinyl
alcohol and polyethylene fibers were evaluated. With increasing of
nanoparticles in fresh samples, the slump flow diameter reduced.
Fibers reduced the flow ability of the samples and viscosity
increased. With increasing of the micro silica particles to cement
ratio from 2/1 to 2/2, the slump flow diameter increased. By adding
silica and alumina nanoparticles up to 3% and 2% respectively, the
compressive strength increased and after decreased. Samples
containing silica nanoparticles and fibers had the highest compressive
strength.
Abstract: Food is widely packaged with plastic materials to
prevent microbial contamination and spoilage. Ionizing radiation is
widely used to sterilize the food-packaging materials. Sterilization by
γ-radiation causes degradation such as embrittlement, stiffening,
softening, discoloration, odour generation, and decrease in molecular
weight. Many antioxidants can prevent γ-degradation but most of
them are toxic. The migration of antioxidants to its environment
gives rise to major concerns in case of food packaging plastics. In
this attempt, we have aimed to utilize synergistic mixtures of
stabilizers which are approved for food-contact applications.
Ethylene-propylene-diene terpolymer has been melt-mixed with
hindered amine stabilizers (HAS), phenolic antioxidants and organophosphites
(hydroperoxide decomposer). Results were discussed by
comparing the stabilizing efficiency of mixtures with and without
phenol system. Among phenol containing systems where we mostly
observed discoloration due to the oxidation of hindered phenol, the
combination of secondary HAS, tertiary HAS, organo-phosphite and
hindered phenol exhibited improved stabilization efficiency than
single or binary additive systems. The mixture of secondary HAS and
tertiary HAS, has shown antagonistic effect of stabilization.
However, the combination of organo-phosphite with secondary HAS,
tertiary HAS and phenol antioxidants have been found to give
synergistic even at higher doses of Gamma-irradiation. The effects
have been explained through the interaction between the stabilizers.
After γ-irradiation, the consumption of oligomeric stabilizer
significantly depends on the components of stabilization mixture. The
effect of the organo-phosphite antioxidant on the overall stability has
been discussed.
Abstract: The influence of three different types of halloysite
nanotubes (HNTs) with different dimensions, namely as camel lake
(CLA), Jarrahdale (JA) and Matauri Bay (MB), on their reinforcing
ability of ethylene propylene dine monomer (EPDM) were
investigated by varying the HNTs loading (from 0-15 phr).
Mechanical properties of the nanocomposites improved with addition
of all three HNTs, but CLA based nanocomposites exhibited a
significant enhancement compared to the other HNTs. For instance,
tensile properties of EPDM nanocomposites increased by 120%,
256% and 340% for MB, JA and CLA, respectively, with addition of
15 phr of HNTs. This could be due to the higher aspect ratio and
higher surface area of CLA compared to others. Scanning electron
microscopy (SEM) of nanocomposites at 15 phr of HNT loadings
showed low amounts of pulled-out nanotubes which confirmed the
presence of more embedded nanotubes inside the EPDM matrix, as
well as aggregates within the fracture surface of EPDM/HNT
nanocomposites
Abstract: The main objective of the study is focused in
producing slag based geopolymer concrete obtained with the addition
of alkali activator. Test results indicated that the reaction of silicates
in slag is based on the reaction potential of sodium hydroxide and the
formation of alumino-silicates. The study also comprises on the
evaluation of the efficiency of polymer reaction in terms of the
strength gain properties for different geopolymer mixtures.
Geopolymer mixture proportions were designed for different binder
to total aggregate ratio (0.3 & 0.45) and fine to coarse aggregate ratio
(0.4 & 0.8). Geopolymer concrete specimens casted with normal
curing conditions reported a maximum 28 days compressive strength
of 54.75 MPa. The addition of glued steel fibres at 1.0% Vf in
geopolymer concrete showed reasonable improvements on the
compressive strength, split tensile strength and flexural properties of
different geopolymer mixtures. Further, comparative assessment was
made for different geopolymer mixtures and the reinforcing effects of
steel fibres were investigated in different concrete matrix.
Abstract: Polyethylene (PE), Polypropylene (PP), Polyethylene
(vinyl acetate) (EVA) and PE-ionomer nanocomposite samples were
prepared by mixing of the polymer with organofilized
montmorillonite fillers Cloisite 93A and Dellite 67G. The amount of
each modified montmorillonite (MMT) was fixed to 5% (w/w). The
twin-screw kneader was used for the compounding of polymer matrix
and chosen nanofillers. The level of MMT exfoliation was studied by
the transmission electron microscopy (TEM) observations. The
mechanical properties of prepared materials were evaluated by
dynamical mechanical analysis at 30°C and by the measurement of
tensile properties (stress and strain at break).
Abstract: High temperature is one of the most detrimental
effects that cause important changes in concrete’s mechanical,
physical, and thermo-physical properties. As a result of these
changes, especially high strength concrete (HSC), may exhibit
damages such as cracks and spallings. To overcome this problem,
incorporating polymer fibers such as polypropylene (PP) in concrete
is a very well-known method. In this study, using RRH, as a
sustainable material, instead of PP fiber in HSC to prevent spallings
and improve physical and thermo-physical properties were
investigated. Therefore, seven HSC mixtures with 0.25 water to
binder ratio were prepared incorporating silica fume and blast furnace
slag. PP and RRH were used at 0.2-0.5% and 0.5-3% by weight of
cement, respectively. All specimens were subjected to high
temperatures (20 (control), 300, 600 and 900˚C) with a heating rate
of 2.5˚C/min and after cooling, residual physical and thermo-physical
properties were determined.
Abstract: A polypropylene hollow fiber membrane module is used for separating dissolved gases which contain dissolved oxygen from water. These dissolved gases can be used for underwater breathing. To be used for a human, the minimum amount of oxygen is essential. To increase separation of dissolved gases, much water and high surface area of hollow fibers are requested. For efficient separation system, performance of single membrane module with high surface area needs to be investigated.
In this study, we set up experimental devices for analyzing separation characteristics of dissolved gases including oxygen from water using a polypropylene hollow fiber membrane module. Separation of dissolved gases from water is investigated with variations of water flow rates. Composition of dissolved gases is also measured using GC. These results expect to be used in developing the portable separation system.
Abstract: Catalytic cracking of butene to propylene was carried out in a continuous-flow fixed-bed reactor over HZSM-5 catalysts modified by nickel and phosphorus. The structure and acidity of catalysts were measured by N2 adsorption, NH3-TPD and XPS. The results revealed that surface area and strong acid sites both decreased with increasing phosphorus loadings. The increment of phosphorus loadings reduced the butene conversion but enhanced the propylene selectivity and catalyst stability.
Abstract: In this study, we developed a complementary electrochromic device consisting of WO3 and NiO films fabricated by rf-magnetron sputtered. The electrochromic properties of WO3 and NiO films were investigated using cyclic voltammograms (CV), performed on WO3 and NiO films immersed in an electrolyte of 1 M LiClO4 in propylene carbonate (PC). Optical and electrochemical of the films, as a function of coloration–bleaching cycle, were characterized using an UV-Vis-NIR spectrophotometer and cyclic voltammetry (CV). After investigating the properties of WO3 film, NiO film, and complementary electrochromic devices, we concluded that this device provides good reversibility, low power consumption of -2.5 V in color state, high variation of transmittance of 58.96%, changes in optical density of 0.81 and good memory effect under open-circuit conditions. In addition, electrochromic component penetration rate can be retained below 20% within 24h, showing preferred memory features; however, component coloring and bleaching response time are about 33s.
Abstract: The surface properties of many materials can be readily and predictably modified by the controlled deposition of thin layers containing appropriate functional groups and this research area is now a subject of widespread interest. The layer-by-layer (lbl) method involves depositing oppositely charged layers of polyelectrolytes onto the substrate material which are stabilized due to strong electrostatic forces between adjacent layers. This type of modification affords products that combine the properties of the original material with the superficial parameters of the new external layers. Through an appropriate selection of the deposited layers, the surface properties can be precisely controlled and readily adjusted in order to meet the requirements of the intended application. In the presented paper a variety of anionic (poly(acrylic acid)) and cationic (linear poly(ethylene imine), polymers were successfully deposited onto the polypropylene nonwoven using the lbl technique. The chemical structure of the surface before and after modification was confirmed by reflectance FTIR spectroscopy, volumetric analysis and selective dyeing tests. As a direct result of this work, new materials with greatly improved properties have been produced. For example, following a modification process significant changes in the electrostatic activity of a range of novel nanocomposite materials were observed. The deposition of polyelectrolyte nanolayers was found to strongly accelerate the loss of electrostatically generated charges and to increase considerably the thermal resistance properties of the modified fabric (the difference in T50% is over 20oC). From our results, a clear relationship between the type of polyelectrolyte layer deposited onto the flat fabric surface and the properties of the modified fabric was identified.
Abstract: In this study was performed in situ consolidation of polypropylene matrix/glass reinforced roving by combining heating systems and roll pressing. The commingled roving during hoop winding was winded on a cylindrical mandrel. The work also presents the advances made in the processing of these materials into composites by conventional technique filament winding. Experimental studies were performed with changing parameters – temperature, pressure and speed. Finally, it describes the investigation of the optimal processing conditions that maximize the mechanical properties of the composites. These properties are good enough for composites to be used as engineering materials in many structural applications.
Abstract: Polyurethane foam is functionalized with Sulfonic acid groups to remove lead ions (Pb2+) from drinking water through a cation exchange process. The synthesis is based on addition polymerization of the -NCO groups of an isocyanate with the –OH groups of a polyol to form the urethane. Toluene-diisocyanateis reacted with Polypropylene glycol to form a linear pre-polymer, which is further polymerized using a chain extender, N, N-bis(2-hydorxyethyl)-2-aminoethane-sulfonic acid (BES). BES acts as a functional group site to exchange Pb2+ ions. A set of experiments was designed to study the effect of various processing parameters on the performance of the synthesized foam. The maximum Pb2+ ion exchange capacity of the foam was found to be 47ppb/g from a 100ppb Pb2+ solution over a period of 60 minutes. A multistage batch filtration process increased the lead removal to 50-54ppb/3g of foam over a period of 90 minutes.
Abstract: An experimental study was conducted on foamed concrete with synthetic and natural fibres consisting of AR-glas, polypropylene, steel, kenaf and oil palm fibre. The foamed concrete mixtures produced had a target density of 1000kg/m3 and a mix ratio of (1:1.5:0.45). The fibres were used as additives. The inclusion of fibre was maintained at a volumetric fraction of 0.25 and 0.4%. The water absorption, thermal and shrinkage were determined to study the effect of the fibre on the durability properties of foamed concrete. The results showed that AR-glass fibre has the lowest percentage value of drying shrinkage compared to others.
Abstract: Polymer-modified bitumen is used to combat different pavement distresses and to increase the life span of pavement. Unmodified bitumen cannot perform better with the range extreme minimum and maximum pavement temperatures. The polymers commonly used to modify the bitumen are ethylene vinyl acetate (EVA) styrene butadiene styrene (SBS). The aim this study to compare the performance of EVA modified bitumen with the bitumen modified by waste low density polyethylene (LDPE), polypropylene (PP) obtained from waste carry bags and waste tyre rubber (CR) to encourage the use of waste polymer whose disposal is big problem today, in place of costly virgin polymer. From the experimental study, it was found that waste polymers are also effective in improving the properties bitumen as that of virgin polymer.
Abstract: Cascade refrigeration systems employ series of single stage vapor compression units which are thermally coupled with evaporator/condenser cascades. Different refrigerants are used in each of the circuit depending on the optimum characteristics shown by the refrigerant for a particular application. In the present research study, a steady state thermodynamic model is developed which simulates the working of an actual cascade system. The model provides COP and all other system parameters e.g. total compressor work, temperature, pressure, enthalpy and entropy at different state points. The working fluid in low temperature circuit (LTC) is CO2 (R744) while Ammonia (R717), Propane (R290), Propylene (R1270), R404A and R12 are the refrigerants in high temperature circuit (HTC). The performance curves of Ammonia, Propane, Propylene, and R404A are compared with R12 to find its nearest substitute. Results show that Ammonia is the best substitute of R12.
Abstract: Shear testing is one of the most complex testing areas where available methods and specimen geometries are different from each other. Therefore, a modified shear test specimen (MSTS) combining the simple uniaxial test with a zone of interest (ZOI) is tested which gives almost the pure shear. In this study, material parameters of polypropylene (PP) and high density polyethylene (HDPE) are first measured by tensile tests with a dogbone shaped specimen. These parameters are then used as an input for the finite element analysis. Secondly, a specially designed specimen (MSTS) is used to perform the shear stress tests in a tensile testing machine to get the results in terms of forces and extension, crack initiation etc. Scanning Electron Microscopy (SEM) is also performed on the shear fracture surface to find material behavior. These experiments are then simulated by finite element method and compared with the experimental results in order to confirm the simulation model. Shear stress state is inspected to find the usability of the proposed shear specimen. Finally, a geometry correction factor can be established for these two materials in this specific loading and geometry with notch using Linear Elastic Fracture Mechanics (LEFM). By these results, strain energy of shear failure and stress intensity factor (SIF) of shear of these two polymers are discussed in the special application of the screw cap opening of the medical or food packages with a temper evidence safety solution.
Abstract: This study intends to improve the bond performance of the polypropylene fiber used as reinforcing fiber for concrete by changing its shape into double crimped type through the enhancement its fabrication process. The bond performance of such double crimped fiber is evaluated by applying the JCI SF-8 (dog-bone shape) testing method. The test results reveal that the double crimped fiber develops bond performance improved by more than 19% compared to the conventional crimped type fiber.
Abstract: When concrete is exposed to high temperatures, some changes may occur in its physical and mechanical properties. Especially, high strength concrete (HSC), may exhibit damages such as cracks and spallings. To overcome this problem, incorporating polymer fibers such as polypropylene (PP) in concrete is a well-known method. In high temperatures, PP decomposes and releases harmful gases such as CO and CO2. This study researches the use of raw rice husk (RRH) as a sustainable material, instead of PP fibers considering its several favorable properties, and its usability in HSC. RRH and PP fibers were incorporated in concrete at 0.5-3% and 0.2-0.5% by weight of cement, respectively. Concrete specimens were exposed to 20 (control), 300, 600 and 900°C. Under these temperatures, residual compressive and splitting tensile strength was determined. During the high temperature effect, the amount of released harmful gases was measured by a gas detector.
Abstract: Venison is well known as a traditional meat type in Europe and it is lower in calories, cholesterol and fat content than common cuts of beef, pork or lamb. The aim of the current research was to determine content of amino acids (LVS ISO 13903:2005) in different types of marinades marinated venison during storage. Beef as a control was analyzed for comparison of obtained results. The meat (2x3x2cm) pieces were marinated in two different types of marinades: red wine and tomato sauce marinade. The prepared meat samples were stored (marinated) at 4±2ºC temperature for 48±1h. Marinated meat was placed in polypropylene trays, hermetically sealed with high barrier polymer film under modified atmosphere (C02 40%+N2 60%) without and with iron based oxygen scavenger sachets (Mitsubishi Gas Chemical Europe Ageless®), all samples were compared with packed marinated products in air ambiance. Results of current research show that changes of amino acids content in marinated venison mainly depend on packaging conditions.
Abstract: The objective of the present study was to determine quality parameters changes of red wine marinade marinated venison during storage. Beef as a control was analysed. Protein, fat, moisture and pH content dynamics as well microbiological quality was analyzed. The meat pieces were marinated in red wine marinade at 4±2ºC temperature for 48±1h. Marinated meat was placed in polypropylene trays, hermetically sealed with high barrier polymer film Multibarrier 60 under modified atmosphere (CO2 40%+N2 60%) without and with oxygen absorber sachets, as a control packaging in air ambiance packed marinated venison and beef was used. Meat samples were analyzed after 0, 4, 7, 11 and 14 days of storage. During the storage of meat, protein and moisture content significantly (p