Abstract: The present research work investigates the seismic
response of reinforced concrete (RC) frame building considering the
effect of modeling masonry infill (MI) walls. The seismic behavior of
a residential 6-storey RC frame building, considering and ignoring
the effect of masonry, is numerically investigated using response
spectrum (RS) analysis. The considered herein building is designed
as a moment resisting frame (MRF) system following the Egyptian
code (EC) requirements. Two developed models in terms of bare
frame and infill walls frame are used in the study. Equivalent
diagonal strut methodology is used to represent the behavior of infill
walls, whilst the well-known software package ETABS is used for
implementing all frame models and performing the analysis. The
results of the numerical simulations such as base shear,
displacements, and internal forces for the bare frame as well as the
infill wall frame are presented in a comparative way. The results of
the study indicate that the interaction between infill walls and frames
significantly change the responses of buildings during earthquakes
compared to the results of bare frame building model. Specifically,
the seismic analysis of RC bare frame structure leads to
underestimation of base shear and consequently damage or even
collapse of buildings may occur under strong shakings. On the other
hand, considering infill walls significantly decrease the peak floor
displacements and drifts in both X and Y-directions.
Abstract: In this paper, a numerical simulation of a finned store
separating from a wing-pylon configuration has been studied and
validated. A dynamic unstructured tetrahedral mesh approach is
accomplished by using three grid sizes to numerically solving the
discretized three dimensional, inviscid and compressible Euler
equations. The method used for computations of separation of an
external store assuming quasi-steady flow condition. Computations of
quasi-steady flow have been directly coupled to a six degree-offreedom
(6DOF) rigid-body motion code to generate store
trajectories. The pressure coefficients at four different angular cuts
and time histories of various trajectory parameters and wing pressure
distribution during the store separation are compared for every grid
size with published experimental data.
Abstract: In this study, a computational fluid dynamics (CFD)
model has been developed for studying the effect of surface
roughness profile on the EHL problem. The cylinders contact
geometry, meshing and calculation of the conservation of mass and
momentum equations are carried out using the commercial software
packages ICEMCFD and ANSYS Fluent. The user defined functions
(UDFs) for density, viscosity and elastic deformation of the cylinders
as the functions of pressure and temperature are defined for the CFD
model. Three different surface roughness profiles are created and
incorporated into the CFD model. It is found that the developed CFD
model can predict the characteristics of fluid flow and heat transfer in
the EHL problem, including the main parameters such as pressure
distribution, minimal film thickness, viscosity, and density changes.
The results obtained show that the pressure profile at the center of the
contact area directly relates to the roughness amplitude. A rough
surface with kurtosis value of more than 3 has greater influence over
the fluctuated shape of pressure distribution than in other cases.
Abstract: Groundwater inflow to the tunnels is one of the most
important problems in tunneling operation. The objective of this
study is the investigation of model dimension effects on tunnel inflow
assessment in discontinuous rock masses using numerical modeling.
In the numerical simulation, the model dimension has an important
role in prediction of water inflow rate. When the model dimension is
very small, due to low distance to the tunnel border, the model
boundary conditions affect the estimated amount of groundwater flow
into the tunnel and results show a very high inflow to tunnel. Hence,
in this study, the two-dimensional universal distinct element code
(UDEC) used and the impact of different model parameters, such as
tunnel radius, joint spacing, horizontal and vertical model domain
extent has been evaluated. Results show that the model domain extent
is a function of the most significant parameters, which are tunnel
radius and joint spacing.
Abstract: In this paper we propose a discrete tracking control of
nonholonomic mobile robots with two degrees of freedom. The
electromechanical model of a mobile robot moving on a horizontal
surface without slipping, with two rear wheels controlled by two
independent DC electric, and one front roal wheel is considered. We
present backstepping design based on the Euler approximate discretetime
model of a continuous-time plant. Theoretical considerations are
verified by numerical simulation.
Abstract: This paper reports the numerical simulation of doublediffusive
natural convection flows within a horizontal annular filled
with a saturated porous medium. The analysis concerns the influence
of the different parameters governing the problem, namely, the
Rayleigh number Ra, the Lewis number Le and the buoyancy ratio N,
on the heat and mass transfer and on the flow structure, in the case of
a fixed radius ratio R = 2. The numerical model used for the
discretization of the dimensionless equations governing the problem
is based on the finite difference method, using the ADI scheme. The
study is focused on steady-state solutions in the cooperation situation.
Abstract: An investigation into Cahn-Hilliard equation was
carried out through numerical simulation to identify a possible phase
separation for one and two dimensional domains. It was observed that
this equation can reproduce important mass fluxes necessary for
phase separation within the miscibility gap and for coalescence of
particles.
Abstract: Fiber Bragg optic sensor is embedded in composite
material to detect and monitor the damage that occurs in composite
structures. In this paper, we deal with the mode-Ι delamination to
determine the material strength to crack propagation, using the
coupling mode theory and T-matrix method to simulate the FBGs
spectrum for both uniform and non-uniform strain distribution. The
double cantilever beam test is modeled in FEM to determine the
longitudinal strain. Two models are implemented, the first is the
global half model, and the second is the sub-model to represent the
FBGs with higher refined mesh. This method can simulate damage in
composite structures and converting strain to a wavelength shifting in
the FBG spectrum.
Abstract: The progress of industry integrated circuits in recent
years has been pushed by continuous miniaturization of transistors.
With the reduction of dimensions of components at 0.1 micron and
below, new physical effects come into play as the standard simulators
of two dimensions (2D) do not consider. In fact the third dimension
comes into play because the transverse and longitudinal dimensions
of the components are of the same order of magnitude. To describe
the operation of such components with greater fidelity, we must
refine simulation tools and adapted to take into account these
phenomena. After an analytical study of the static characteristics of
the component, according to the different operating modes, a
numerical simulation is performed of field-effect transistor with
submicron gate MESFET GaInP. The influence of the dimensions of
the gate length is studied. The results are used to determine the
optimal geometric and physical parameters of the component for their
specific applications and uses.
Abstract: This paper presents the details of a numerical study of
buckling and post buckling behaviour of laminated carbon fiber
reinforced plastic (CFRP) thin-walled cylindrical shell under axial
compression using asymmetric meshing technique (AMT) by
ABAQUS. AMT is considered to be a new perturbation method to
introduce disturbance without changing geometry, boundary
conditions or loading conditions. Asymmetric meshing affects both
predicted buckling load and buckling mode shapes. Cylindrical shell
having lay-up orientation [0^o/+45^o/-45^o/0^o] with radius to thickness
ratio (R/t) equal to 265 and length to radius ratio (L/R) equal to 1.5 is
analysed numerically. A series of numerical simulations
(experiments) are carried out with symmetric and asymmetric
meshing to study the effect of asymmetric meshing on predicted
buckling behaviour. Asymmetric meshing technique is employed in
both axial direction and circumferential direction separately using
two different methods, first by changing the shell element size and
varying the total number elements, and second by varying the shell
element size and keeping total number of elements constant. The
results of linear analysis (Eigenvalue analysis) and non-linear
analysis (Riks analysis) using symmetric meshing agree well with
analytical results. The results of numerical analysis are presented in
form of non-dimensional load factor, which is the ratio of buckling
load using asymmetric meshing technique to buckling load using
symmetric meshing technique. Using AMT, load factor has about 2%
variation for linear eigenvalue analysis and about 2% variation for
non-linear Riks analysis. The behaviour of load end-shortening curve
for pre-buckling is same for both symmetric and asymmetric meshing
but for asymmetric meshing curve behaviour in post-buckling
becomes extraordinarily complex. The major conclusions are:
different methods of AMT have small influence on predicted
buckling load and significant influence on load displacement curve
behaviour in post buckling; AMT in axial direction and AMT in
circumferential direction have different influence on buckling load
and load displacement curve in post-buckling.
Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: The spring-driven ball-type check valve is one of the
most important components of hydraulic systems: it controls the
position of the ball and prevents backward flow. To simplify the
structure, the spring must be eliminated, and to accomplish this, the
flow pattern and the behavior of the check ball in L-shaped pipe must
be determined. In this paper, we present a full-scale model of a check
ball made of acrylic resin, and we determine the relationship between
the initial position of the ball, the position and diameter of the inflow
port. The check flow rate increases in a standard center inflow model,
and it is possible to greatly decrease the check-flow rate by shifting the
inflow from the center.
Abstract: In the present study, mixed convection in a horizontal
rectangular duct using Al2O3 is numerically investigated. The effects
of different Rayleigh number, Reynolds number and radiation on
flow and heat transfer characteristics are studied in detail. This study
covers Rayleigh number in the range of 2 × 10^6 ≤ Ra ≤ 2 × 10^7 and
Reynolds number in the range of 100 ≤ Re ≤ 1100. Results reveal that
the Nusselt number increases as Reynolds and Rayleigh numbers
increase. It is also found that the dimensionless temperature
distribution increases as Rayleigh number increases.
Abstract: In this work, we propose and analyze a model of
Phytoplankton-Zooplankton interaction with harvesting considering
that some species are exploited commercially for food. Criteria for
local stability, instability and global stability are derived and some
threshold harvesting levels are explored to maintain the population
at an appropriate equilibrium level even if the species are exploited
continuously.Further,biological and bionomic equilibria of the system
are obtained and an optimal harvesting policy is also analysed using
the Pantryagin’s Maximum Principle.Finally analytical findings are
also supported by some numerical simulations.
Abstract: This paper reports the numerical and experimental
performances of Double Glass Wall are investigated. Two
configurations were considered namely, the Double Clear Glass Wall
(DCGW) and the Double Translucent Glass Wall (DTGW). The
coupled governing equations as well as boundary conditions are
solved using the finite element method (FEM) via COMSOLTM
Multiphysics. Temperature profiles and flow field of the DCGW and
DTGW are reported and discussed. Different constant heat fluxes
were considered as 400 and 800 W.m-2 the corresponding initial
condition temperatures were 30.5 and 38.5ºC respectively. The
results show that the simulation results are in agreement with the
experimental data. Conclusively, the model considered in this study
could reasonable be used simulate the thermal and ventilation
performance of the DCGW and DTGW configurations.
Abstract: Present study is aimed on the cutting process of circular
cross-section rods where the fracture is used to separate one rod
into two pieces. Incorporating the phenomenological ductile fracture
model into the explicit formulation of finite element method, the
process can be analyzed without the necessity of realizing too many
real experiments which could be expensive in case of repetitive
testing in different conditions. In the present paper, the steel AISI
1045 was examined and the tensile tests of smooth and notched
cylindrical bars were conducted together with biaxial testing of the
notched tube specimens to calibrate material constants of selected
phenomenological ductile fracture models. These were implemented
into the Abaqus/Explicit through user subroutine VUMAT and used
for cutting process simulation. As the calibration process is based
on variables which cannot be obtained directly from experiments,
numerical simulations of fracture tests are inevitable part of the
calibration. Finally, experiments regarding the cutting process were
carried out and predictive capability of selected fracture models is
discussed. Concluding remarks then make the summary of gained
experience both with the calibration and application of particular
ductile fracture criteria.
Abstract: A finite difference/front tracking method is used to
study the motion of three-dimensional deformable drops suspended in
plane Poiseuille flow at non-zero Reynolds numbers. A parallel
version of the code was used to study the behavior of suspension on a
reasonable grid resolution (grids). The viscosity and density of drops
are assumed to be equal to that of the suspending medium. The effect
of the Reynolds number is studied in detail. It is found that drops
with small deformation behave like rigid particles and migrate to an
equilibrium position about half way between the wall and the
centerline (the Segre-Silberberg effect). However, for highly
deformable drops there is a tendency for drops to migrate to the
middle of the channel, and the maximum concentration occurs at the
centerline. The effective viscosity of suspension and the fluctuation
energy of the flow across the channel increases with the Reynolds
number of the flow.
Abstract: The phased-array ultrasound transducer types are
utilities for medical ultrasonography as well as optical imaging.
However, their discontinuity characteristic limits the applications due
to the artifacts contaminated into the reconstructed images. Because
of the effects of the ultrasound pressure field pattern to the echo
ultrasonic waves as well as the optical modulated signal, the side
lobes of the focused ultrasound beam induced by discontinuity of the
phased-array ultrasound transducer might the reason of the artifacts.
In this paper, a simple method in approach of numerical simulation
was used to investigate the limitation of discontinuity of the elements
in phased-array ultrasound transducer and their effects to the
ultrasound pressure field. Take into account the change of ultrasound
pressure field patterns in the conditions of variation of the pitches
between elements of the phased-array ultrasound transducer, the
appropriated parameters for phased-array ultrasound transducer
design were asserted quantitatively.
Abstract: Nonstandard tests are necessary for analyses and
verification of new developed structural and technological solutions
with application of composite materials. One of the most critical
primary structural parts of a typical aerospace structure is T-joint.
This structural element is loaded mainly in shear, bending, peel and
tension. The paper is focused on the shear loading simulations. The
aim of the work is to obtain a representative uniform distribution of
shear loads along T-joint during the mechanical testing. A new
design of T-joint test procedure, numerical simulation and
optimization of representative boundary conditions are presented.
The different conditions and inaccuracies both in simulations and
experiments are discussed. The influence of different parameters on
stress and strain distributions is demonstrated on T-joint made of
CFRP (carbon fibre reinforced plastic). A special test rig designed by
VZLU (Aerospace Research and Test Establishment) for T-shear test
procedure is presented.
Abstract: This paper is devoted to the study of a viscous
incompressible flow around a circular cylinder performing harmonic
oscillations, especially the steady streaming phenomenon. The
research methodology is based on the asymptotic explanation method
combined with the computational bifurcation analysis. The research
approach develops Schlichting and Wang decomposition method.
Present studies allow to identify several regimes of the secondary
streaming with different flow structures. The results of the research
are in good agreement with experimental and numerical simulation
data.