Abstract: This study presents the application of artificial
neural network for modeling the phenolic compound
migration through vertical soil column. A three layered feed
forward neural network with back propagation training
algorithm was developed using forty eight experimental data
sets obtained from laboratory fixed bed vertical column tests.
The input parameters used in the model were the influent
concentration of phenol(mg/L) on the top end of the soil
column, depth of the soil column (cm), elapsed time after
phenol injection (hr), percentage of clay (%), percentage of
silt (%) in soils. The output of the ANN was the effluent
phenol concentration (mg/L) from the bottom end of the soil
columns. The ANN predicted results were compared with the
experimental results of the laboratory tests and the accuracy of
the ANN model was evaluated.
Abstract: Construction of portable device for fast analysis of energetic materials is described in this paper. The developed analytical system consists of two main parts: a miniaturized microcolumn liquid chromatograph of unique construction and original chemiluminescence detector. This novel portable device is able to determine selectively most of nitramine- and nitroester-based explosives as well as inorganic nitrates at trace concentrations in water or soil extracts in less than 8 minutes.
Abstract: The paper considers the effect of feed plate location
on the interactions in a seven plate binary distillation column. The
mathematical model of the distillation column is deduced based on
the equations of mass and energy balances for each stage, detailed
model for both reboiler and condenser, and heat transfer equations.
The Dynamic Relative Magnitude Criterion, DRMC is used to assess
the interactions in different feed plate locations for a seven plate
(Benzene-Toluene) binary distillation column ( the feed plate is
originally at stage 4). The results show that whenever we go far from
the optimum feed plate position, the level of interaction augments.
Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: A complex valued neural network is a neural network
which consists of complex valued input and/or weights and/or thresholds
and/or activation functions. Complex-valued neural networks
have been widening the scope of applications not only in electronics
and informatics, but also in social systems. One of the most important
applications of the complex valued neural network is in signal
processing. In Neural networks, generalized mean neuron model
(GMN) is often discussed and studied. The GMN includes a new
aggregation function based on the concept of generalized mean of all
the inputs to the neuron. This paper aims to present exhaustive results
of using Generalized Mean Neuron model in a complex-valued neural
network model that uses the back-propagation algorithm (called
-Complex-BP-) for learning. Our experiments results demonstrate the
effectiveness of a Generalized Mean Neuron Model in a complex
plane for signal processing over a real valued neural network. We
have studied and stated various observations like effect of learning
rates, ranges of the initial weights randomly selected, error functions
used and number of iterations for the convergence of error required on
a Generalized Mean neural network model. Some inherent properties
of this complex back propagation algorithm are also studied and
discussed.
Abstract: Being creative in an educational environment, such as in the university, has many times been downplayed by bureaucracy, human inadequacy and physical hindrance. These factors control, stifle and subsequently condemn this natural phenomenon which is normally exuded by the tertiary community. If taken in a positive light, creativity has always led to many new discoveries and inventions. These creations are then gradually developed for the university reputation and achievements, in all fields of studies from the sciences to the humanities. This paper attempts to explore, through more than twenty years of observation, issues that stifle the university citizenry – academicians and students- – creativity. It also scrutinizes how enhancement of such creativity can be further supported by bureaucracy simplicity, encouraging and developing human potential and constructing uncompromising physical infrastructure and administrative support. These ideals – all of which can help to promote creativity, increases the productivity of the university community in aspects of teaching, research, publication, innovation and commercialization; be it at national as well as at international arena for the good of human and societal growth and development. This discursive presentation hopes to address another issue on promoting university community creativity through several deliverables which require cooperation from every quarter of the institution so that being creative continues to be promoted for sustainable human capital growth and development of the country, if not, the global community.
Abstract: Modeling of Panel Zone (PZ) seismic behavior,
because of its role in overall ductility and lateral stiffness of steel
moment frames, has been considered a challenge for years. There are
some studies regarding the effects of different doubler plates
thicknesses and geometric properties of PZ on its seismic behavior.
However, there is not much investigation on the effects of number of
provided continuity plates in case of presence of one triangular
haunch, two triangular haunches and rectangular haunch (T shape
haunches) for exterior columns. In this research first detailed finite
element models of 12tested connection of SAC joint venture were
created and analyzed then obtained cyclic behavior backbone curves
of these models besides other FE models for similar tests were used
for neural network training. Then seismic behavior of these data is
categorized according to continuity plate-s arrangements and
differences in type of haunches. PZ with one-sided haunches have
little plastic rotation. As the number of continuity plates increases
due to presence of two triangular haunches (four continuity plate),
there will be no plastic rotation, in other words PZ behaves in its
elastic range. In the case of rectangular haunch, PZ show more plastic
rotation in comparison with one-sided triangular haunch and
especially double-sided triangular haunches. Moreover, the models
that will be presented in case of triangular one-sided and double-
sided haunches and rectangular haunches as a result of this study
seem to have a proper estimation of PZ seismic behavior.
Abstract: Focusing on the environmental issues, including the reduction of scrap and consumer residuals, along with the benefiting from the economic value during the life cycle of goods/products leads the companies to have an important competitive approach. The aim of this paper is to present a new mixed nonlinear facility locationallocation model in recycling collection networks by considering multi-echelon, multi-suppliers, multi-collection centers and multifacilities in the recycling network. To make an appropriate decision in reality, demands, returns, capacities, costs and distances, are regarded uncertain in our model. For this purpose, a fuzzy mathematical programming-based possibilistic approach is introduced as a solution methodology from the recent literature to solve the proposed mixed-nonlinear programming model (MNLP). The computational experiments are provided to illustrate the applicability of the designed model in a supply chain environment and to help the decision makers to facilitate their analysis.
Abstract: The spin (ms) and orbital (mo) magnetic moment of
the antiferromagnetic NiO and MnO have been studied in the local
spin density approximation (LSDA+U) within full potential linear
muffin-tin orbital (FP-LMTO method with in the coulomb interaction
U varying from 0 to 10eV, exchange interaction J, from 0 to 1.0eV,
and volume compression VC in range of 0 to 80%. Our calculated
results shown that the spin magnetic moments and the orbital
magnetic moments increase linearly with increasing U and J. While
the interesting behaviour appears when volume compression is
greater than 70% for NiO and 50% for MnO at which ms collapses.
Further increase of volume compression to be at 80% leads to the
disappearance of both magnetic moments.
Abstract: In this paper, experimental testing and numerical analysis were used to investigate the effect of tube thickness on the face bending for concrete filled hollow sections connected to other structural members using Extended Hollobolts. Six samples were tested experimentally by applying pull-out load on the bolts. These samples were designed to fail by column face bending. The main variable in all tests is the column face thickness. Finite element analyses were also performed using ABAQUS 6.11 to extend the experimental results and to quantify the effect of column face thickness. Results show that, the column face thickness has a clear impact on the connection strength and stiffness. However, the amount of improvement in the connection stiffness by changing the column face thickness from 5mm to 6.3mm seems to be higher than that when increasing it from 6.3mm to 8mm. The displacement at which the bolts start pulling-out from their holes increased with the use of thinner column face due to the high flexibility of the section. At the ultimate strength, the yielding of the column face propagated to the column corner and there was no yielding in its walls. After the ultimate resistance is reached, the propagation of the yielding was mainly in the column face with a miner yielding in the walls.
Abstract: Chevron frames (Inverted-V-braced frames or Vbraced
frames) have seismic disadvantages, such as not good exhibit force redistribution capability and compression brace buckles
immediately. Researchers developed new design provisions on
increasing both the ductility and lateral resistance of these structures
in seismic areas. One of these new methods is adding zipper columns, as proposed by Khatib et al. (1988) [2]. Zipper columns are
vertical members connecting the intersection points of the braces
above the first floor. In this paper applicability of the suspended
zipper system to Seismic Rehabilitation of Steel Structures is investigated.
The models are 3-, 6-, 9-, and 12-story Inverted-V-braced frames.
In this case, it is assumed that the structures must be rehabilitated. For rehabilitation of structures, zipper column is used. The result of
researches showed that the suspended zipper system is effective in
case of 3-, 6-, and 9-story Inverted-V-braced frames and it would
increase lateral resistance of structure up to life safety level. But in
case of high-rise buildings (such as 12 story frame), it doesn-t show
good performance. For solving this problem, the braced bay can
consist of small “units" over the height of the entire structure, which each of them is a zipper-braced bay with a few stories. By using this
method the lateral resistance of 12 story Inverted-V-braced frames is increased up to safety life level.
Abstract: Magnetic Nanoparticles (MNPs) have great potential
to overcome many of the shortcomings of the present diagnostic and
therapeutic approaches used in cancer diagnosis and treatment. This
Literature review discusses the use of Magnetic Nanoparticles
focusing mainly on Iron oxide based MNPs in cancer imaging using
MRI.
Abstract: In this paper, to resolve the problem of existing
schemes, an alternative fast handover Proxy Mobile IPv6 (PMIPv6)
scheme using the IEEE 802.21 Media Independent Handover (MIH)
function is proposed for heterogeneous wireless networks. The proposed
scheme comes to support fast handover for the mobile node
(MN) irrespective of the presence or absence of MIH functionality
as well as L3 mobility functionality, whereas the MN in existing
schemes has to implement MIH functionality. That is, the proposed
scheme does not require the MN to be involved in MIH related signaling
required for handover procedure. The base station (BS) with MIH
functionality performs handover on behalf of the MN. Therefore, the
proposed scheme can reduce burden and power consumption of MNs
with limited resource and battery power since MNs are not required
to be involved for the handover procedure. In addition, the proposed
scheme can reduce considerably traffic overhead over wireless links
between MN and BS since signaling messages are reduced.
Abstract: Almost all universities include some form of assignment in their courses. The assignments are either carried out in either in groups or individually. To effectively manage these submitted assignments, a well-designed assignment submission system is needed, hence the need for an online assignment submission system to facilitate the distribution, and collection of assignments on due dates. The objective of such system is to facilitate interaction of lecturers and students for assessment and grading purposes. The aim of this study was to create a web based online assignment submission system for University of Mauritius. The system was created to eliminate the traditional process of giving an assignment and collecting the answers for the assignment. Lecturers can also create automated assessment to assess the students online. Moreover, the online submission system consists of an automatic mailing system which acts as a reminder for students about the deadlines of the posted assignments. System was tested to measure its acceptance rate among both student and lecturers.
Abstract: In this paper we will consider the most known ratios
control schemes ((L/D, V/B),(L/D,V/F), Ryskamp-s, and
(D/(L+D),V/B)) for binary distillation column and we compare them
in the basis of interactions and disturbance propagation. The models
for these configurations are deuced using mathematical
transformations taking the energy balance structure (LV) as a base
model. The dynamic relative magnitude criterion (DRMC) is used to
assess the interactions. The results show that the introduction of
ratios in controlling the column tends to minimize the degree of
interactions between the loops.
Abstract: The present investigation aimed to study the
histomorphometric characterizations of the thyroid gland of the duck.
Five adult male and five adult female ducks were used in the
experiment. Results showed that the overall histological structure of
the thyroid gland of the duck were similar to those of the other
vertebrae. The gland consisted of roughly spherical randomly
distributed micro and macrofollicles with very little interstitial tissue
between them. Each follicle is lined by a single layer of epithelial
cells enclosing a cavity, the follicular cavity, which is filled with
colloid. Ultrastructural findings showed that the apical surface of the
follicular cells bears a variable number of short, irregularly
distributed microvilli which are apparently more numerous on the
columnar cells than on the lower, relatively inactive cells.
Mitochondria and rough endoplasmic reticulum occupy the
subnuclear region of the follicular cell, whereas the Golgi complex,
free ribosomes and colloid droplets were found in the apical
cytoplasm. At light or electron microscopic levels, there was no sex
difference in histomorphometric characteristics of the thyroid
glands.ls.
Abstract: The objective of this study is to identify the factors
that influence the online purchasing loyalty for Thai herbal products.
Survey research is used to gather data from Thai herb online
merchants to assess factors that have impacts on enhancing loyalty.
Data were collected from 300 online customers who had experience
in online purchasing of Thai Herbal products. Prior experience
consists of data from previous usage of online herbs, herb purchase
and internet usage. E-Quality data consists of information quality,
system quality, service quality and the product quality of Thai herbal
products sold online. The results suggest that prior experience, Equality,
attitude toward purchase and trust in online merchant have
major impacts on loyalty. The good attitude and E-Quality of
purchasing Thai herbal product online are the most significant
determinants affecting loyalty.
Abstract: An attempt was made for availability of wastewater reuse/reclamation for irrigation purposes using phytoremediation “the low cost and less technology", using six local aquatic macrophytes “e.g. T. angustifolia, B. maritimus, Ph. australis, A. donax, A. plantago-aquatica and M. longifolia (Linn)" as biological waste purifiers. Outdoor experiments/designs were conducted from May 03, 2007 till October 15, 2008, close to one of the main sewage channels of Sulaimani City/Iraq*. All processes were mainly based on conventional wastewater treatment processes, besides two further modifications were tested, the first was sand filtration pots, implanted by individual species of experimental macrophytes and the second was constructed wetlands implanted by experimental macrophytes all together. Untreated and treated wastewater samples were analyzed for their key physico-chemical properties (only heavy metals Fe, Mn, Zn and Cu with particular reference to removal efficiency by experimental macrophytes are highlighted in this paper). On the other hand, vertical contents of heavy metals were also evaluated from both pots and the cells of constructed wetland. After 135 days, macrophytes were harvested and heavy metals were analyzed in their biomass (roots/shoots) for removal efficiency assessment (i.e. uptake/ bioaccumulation rate). Results showed that; removal efficiency of all studied heavy metals was much higher in T. angustifolia followed by Ph. Australis, B. maritimus and A. donax in triple experiment sand pots. Constructed wetland experiments have revealed that; the more replicated constructed wetland cells the highest heavy metal removal efficiency was indicated.
Abstract: In this study, the effect of greywater irrigation on airwater interfacial area is investigated. Several soil column experiments were conducted for different greywater irrigation to develop the pressure-saturation curves. Surface tension was measured for different greywater concentration and fitted for Gibbs adsorption equation. Pressure-saturation curves show that the reduction of capillary rise stops when it reaches its critical micelle concentration (CMC). A simple theory is derived from pressure-saturation curves for calculating air-water interfacial area in porous medium during greywater irrigation by introducing a term 'hydraulic radius' for the pores. This term diminishes any effect of pore shapes on the air-water interfacial area. The air-water interfacial area was calculated using the pressure-saturation curves and found that it decreases with increasing moisture content. But no significant effect was observed on air-water interfacial area for different greywater irrigation. A maximum of 10% variation in interfacial area was observed at the residual saturation zone.
Abstract: Chatter vibration has been a troublesome problem for a
machine tool toward the high precision and high speed machining.
Essentially, the machining performance is determined by the dynamic
characteristics of the machine tool structure and dynamics of cutting
process. Therefore the dynamic vibration behavior of spindle tool
system greatly determines the performance of machine tool. The
purpose of this study is to investigate the influences of the machine
frame structure on the dynamic frequency of spindle tool unit through
finite element modeling approach. To this end, a realistic finite
element model of the vertical milling system was created by
incorporated the spindle-bearing model into the spindle head stock of
the machine frame. Using this model, the dynamic characteristics of
the milling machines with different structural designs of spindle head
stock and identical spindle tool unit were demonstrated. The results of
the finite element modeling reveal that the spindle tool unit behaves
more compliant when the excited frequency approaches the natural
mode of the spindle tool; while the spindle tool show a higher dynamic
stiffness at lower frequency that may be initiated by the structural
mode of milling head. Under this condition, it is concluded that the
structural configuration of spindle head stock associated with the
vertical column of milling machine plays an important role in
determining the machining dynamics of the spindle unit.