Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: In recent five decades, textured yarns of polyester fiber produced by false twist method are the most
important and mass-produced manmade fibers. There are
many parameters of cross section which affect the physical and mechanical properties of textured yarns. These parameters
are surface area, perimeter, equivalent diameter, large
diameter, small diameter, convexity, stiffness, eccentricity, and hydraulic diameter. These parameters were evaluated by
digital image processing techniques. To find trends between production criteria and evaluated parameters of cross section, three criteria of production line have been adjusted and different types of yarns were produced. These criteria are
temperature, drafting ratio, and D/Y ratio. Finally the relations between production criteria and cross section parameters were
considered. The results showed that the presented technique can recognize and measure the parameters of fiber cross section in acceptable accuracy. Also, the optimum condition
of adjustments has been estimated from results of image analysis evaluation.
Abstract: Methanol-to-olefins coupled with transformation of
coal or natural gas to methanol gives an interesting and promising way
to produce ethylene and propylene. To investigate solid concentration
in gas-solid fluidized bed for methanol-to-olefins process catalyzed by
SAPO-34, a cold model experiment system is established in this paper.
The system comprises a gas distributor in a 300mm internal diameter
and 5000mm height acrylic column, the fiber optic probe system and
series of cyclones. The experiments are carried out at ambient
conditions and under different superficial gas velocity ranging from
0.3930m/s to 0.7860m/s and different initial bed height ranging from
600mm to 1200mm. The effects of radial distance, axial distance,
superficial gas velocity, initial bed height on solid concentration in the
bed are discussed. The effects of distributor shape and porosity on
solid concentration are also discussed. The time-averaged solid
concentration profiles under different conditions are obtained.
Abstract: Sampling and analysis of leachate from Bhalaswa
landfill and groundwater samples from nearby locations, clearly
indicated the likely contamination of groundwater due to landfill
leachate. The results of simulation studies carried out for the
migration of Chloride from landfill shows that the simulation results
are in consonance with the observed concentration of Chloride in the
vicinity of landfill facility. The solid waste disposal system presently
being practiced in Delhi consists of mere dumping of wastes
generated, at three locations Bhalaswa, Ghazipur, and Okhla without
any regard to proper care for the protection of surrounding
environment. Bhalaswa landfill site in Delhi, which is being operated
as a dump site, is expected to become cause of serious groundwater
pollution in its vicinity. The leachate from Bhalaswa landfill was
found to be having a high concentration of chlorides, as well as DOC,
COD. The present study was undertaken to determine the likely
concentrations of principle contaminants in the groundwater over a
period of time due to the discharge of such contaminants from
landfill leachates to the underlying groundwater. The observed
concentration of chlorides in the groundwater within 75m of the
radius of landfill facility was found to be in consonance with the
simulated concentration of chloride in groundwater considering one
dimensional transport model, with finite mass of contaminant source.
Governing equation of contaminant transport involving advection and
diffusion-dispersion was solved in matlab7.0 using finite difference
method.
Abstract: Curriculum is one of the most important inputs in higher education system and for knowing the strong and weak spots of it we need evaluation. The main purpose of this study was to survey of the curriculum quality of Insurance Management field. Case: University of Allameh Taba Tabaee(according to view point of students,alumni,employer and faculty members).Descriptive statistics (mean, tables, percentages, frequency distribution) and inferential statistics (CHI SQUARE) were used to analyze the data. Six criterions considered for the Quality of curriculum: objectives, content, teaching and learning methods, space and facilities, Time, assessment of learning. objectives, teaching and learning methods criterions was desirable level, content criteria was undesirable level, space and facilities, time and assessment of learning were rather desirable level. The quality of curriculum of insurance management field was relatively desirable level.
Abstract: Thailand-s health system is challenged by the rising
number of patients and decreasing ratio of medical
practitioners/patients, especially in rural areas. This may tempt
inexperienced GPs to rush through the process of anamnesis with the
risk of incorrect diagnosis. Patients have to travel far to the hospital
and wait for a long time presenting their case. Many patients try to
cure themselves with traditional Thai medicine. Many countries are
making use of the Internet for medical information gathering,
distribution and storage. Telemedicine applications are a relatively
new field of study in Thailand; the infrastructure of ICT had
hampered widespread use of the Internet for using medical
information. With recent improvements made health and technology
professionals can work out novel applications and systems to help
advance telemedicine for the benefit of the people. Here we explore
the use of telemedicine for people with health problems in rural areas
in Thailand and present a Telemedicine Diagnosis System for Rural
Thailand (TEDIST) for diagnosing certain conditions that people
with Internet access can use to establish contact with Community
Health Centers, e.g. by mobile phone. The system uses a Web-based
input method for individual patients- symptoms, which are taken by
an expert system for the analysis of conditions and appropriate
diseases. The analysis harnesses a knowledge base and a backward
chaining component to find out, which health professionals should be
presented with the case. Doctors have the opportunity to exchange
emails or chat with the patients they are responsible for or other
specialists. Patients- data are then stored in a Personal Health Record.
Abstract: Based on a global kinetics of direct dimethyl ether (DME) synthesis process from syngas, a steady-state one-dimensional mathematical model for the bubble column slurry reactor (BCSR) has been established. It was built on the assumption of plug flow of gas phase, sedimentation-dispersion model of catalyst grains and isothermal chamber regardless of reaction heats and rates for the design of an industrial scale bubble column slurry reactor. The simulation results indicate that higher pressure and lower temperature were favorable to the increase of CO conversion, DME selectivity, products yield and the height of slurry bed, which has a coincidence with the characteristic of DME synthesis reaction system, and that the height of slurry bed is lessen with the increasing of operation temperature in the range of 220-260℃. CO conversion, the optimal operation conditions in BCSR were proposed.
Abstract: Mobile IPv6 (MIPv6) describes how mobile node can change its point of attachment from one access router to another. As a demand for wireless mobile devices increases, many enhancements for macro-mobility (inter-domain) protocols have been proposed, designed and implemented in Mobile IPv6. Hierarchical Mobile IPv6 (HMIPv6) is one of them that is designed to reduce the amount of signaling required and to improve handover speed for mobile connections. This is achieved by introducing a new network entity called Mobility Anchor Point (MAP). This report presents a comparative study of the Hierarchical Mobility IPv6 and Mobile IPv6 protocols and we have narrowed down the scope to micro-mobility (intra-domain). The architecture and operation of each protocol is studied and they are evaluated based on the Quality of Service (QoS) parameter; handover latency. The simulation was carried out by using the Network Simulator-2. The outcome from this simulation has been discussed. From the results, it shows that, HMIPv6 performs best under intra-domain mobility compared to MIPv6. The MIPv6 suffers large handover latency. As enhancement we proposed to HMIPv6 to locate the MAP to be in the middle of the domain with respect to all Access Routers. That gives approximately same distance between MAP and Mobile Node (MN) regardless of the new location of MN, and possible shorter distance. This will reduce the delay since the distance is shorter. As a future work performance analysis is to be carried for the proposed HMIPv6 and compared to HMIPv6.
Abstract: Basic objective of this study is to create a regression
analysis method that can estimate the length of a plastic hinge which
is an important design parameter, by making use of the outcomes of
(lateral load-lateral displacement hysteretic curves) the experimental
studies conducted for the reinforced square concrete columns. For
this aim, 170 different square reinforced concrete column tests results
have been collected from the existing literature. The parameters
which are thought affecting the plastic hinge length such as crosssection
properties, features of material used, axial loading level,
confinement of the column, longitudinal reinforcement bars in the
columns etc. have been obtained from these 170 different square
reinforced concrete column tests. In the study, when determining the
length of plastic hinge, using the experimental test results, a
regression analysis have been separately tested and compared with
each other. In addition, the outcome of mentioned methods on
determination of plastic hinge length of the reinforced concrete
columns has been compared to other methods available in the
literature.
Abstract: In the present study, a heterogeneous and
homogeneous gas flow dispersion model for simulation and
optimisation of a large-scale catalytic slurry reactor for the direct
synthesis of dimethyl ether (DME) from syngas and CO2, using a
churn-turbulent regime was developed. In the heterogeneous gas flow
model the gas phase was distributed into two bubble phases: small
and large, however in the homogeneous one, the gas phase was
distributed into only one large bubble phase. The results indicated
that the heterogeneous gas flow model was in more agreement with
experimental pilot plant data than the homogeneous one.
Abstract: Iron ore and coal are the two major important raw
materials being used in Iron making industries. Usually ore fines
containing around 5% Alumina are rejected due to higher proportion
of alumina. Therefore, a technology or process which may reduce
the alumina content by 2% by beneficiation process will be highly
attractive . In addition fine coals with ash content is used nearly 12%
is directly injected in blast furnace. Fast fluidization is a technology
by using dry beneficiation of coal and iron ore can be done. During
the fluidization process the iron ore band coal is fluidized at high
velocity in the riser of a fast fluidized bed, the heavier and coarse
particles is generally settled at the bottom in a dense zone of the riser
while the finer and lighter particle are entrained to the top dilute zone
and then via a cyclone is fed back to the bottom of the riser column.
Most of the alumina and low ash fine size coals being lighter are
expected to move up to the riser and by a natural beneficiation of
ores is expected to take place in the riser. Therefore in this study an
attempt has been made for dry beneficiation of iron ore and coal in a
fluidized bed and its hydrodynamic characterization.
Abstract: This paper presents the results of an analytical study
on the seismic response of a Multi-Span-Simply-Supported precast
bridge in Washington State. The bridge was built in the early 1960's
along Interstate 5 and was widened the first time in 1979 and the
second time in 2001. The primary objective of this research project
is to determine the seismic vulnerability of the bridge in order to
develop the required retrofit measure. The seismic vulnerability of
the bridge is evaluated using two seismic evaluation methods
presented in the FHWA Seismic Retrofitting Manual for Highway
Bridges, Method C and Method D2. The results of the seismic
analyses demonstrate that Method C and Method D2 vary markedly
in terms of the information they provide to the bridge designer
regarding the vulnerability of the bridge columns.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: Crystallization has been used for the separation of
chloronitrobenzene or CNBs, which are isomeric substances (o-, mand
p-CNB) and important intermediates in chemical productions. Effects of feed composition on the crystallization of m- and p-CNB was first studied. The results conform to the binary phase diagram of
m- and p-CNB. After that, effects of FAU zeolites (NaX, CaX, BaX, NaY and CaY) above the eutectic composition (63.5 and 65.0 wt% m-CNB in the feed) was also investigated. The results showed that
the FAU zeolites significantly affected the precipitates, the
composition of which was shifted from being rich in m-CNB to rich
in p-CNB. Effects of the number of FAU zeolites on the precipitate composition was then studied. The results revealed that the
precipitates from the lower number of the zeolites had higher p-CNB purity than those from the higher number of zeolite.
Abstract: This paper presents an integrated knowledge-based
approach to multi-scale modeling of aquatic systems, with a view to
enhancing predictive power and aiding environmental management
and policy-making. The basic phases of this approach have been
exemplified in the case of a bay in Saronicos Gulf (Attiki, Greece).
The results showed a significant problem with rising phytoplankton
blooms linked to excessive microbial growth, arisen mostly due to
increased nitrogen inflows; therefore, the nitrification/denitrification
processes of the benthic and water column sub-systems have
provided the quality variables to be monitored for assessing
environmental status. It is thereby demonstrated that the proposed
approach facilitates modeling choices and implementation option
decisions, while it provides substantial support for knowledge and
experience capitalization in long-term water management.
Abstract: The Beijing road traffic system, as a typical huge
urban traffic system, provides a platform for analyzing the complex
characteristics and the evolving mechanisms of urban traffic systems.
Based on dynamic network theory, we construct the dynamic model
of the Beijing road traffic system in which the dynamical properties
are described completely. Furthermore, we come into the conclusion
that urban traffic systems can be viewed as static networks, stochastic
networks and complex networks at different system phases by
analyzing the structural randomness. As well as, we demonstrate the
evolving process of the Beijing road traffic network based on real
traffic data, validate the stochastic characteristics and the scale-free
property of the network at different phases
Abstract: The paper attempts to elucidate the columnar structure
of the cortex by answering the following questions. (1) Why the
cortical neurons with similar interests tend to be vertically arrayed
forming what is known as cortical columns? (2) How to describe the
cortex as a whole in concise mathematical terms? (3) How to design
efficient digital models of the cortex?
Abstract: The Kowsar dam supply water for different usages
such as drinking, industrial, agricultural and aquaculture farms
usages and located next to the city of Dehdashat in Kohgiluye and
Boyerahmad province in southern Iran. There are some towns and
villages on the Kowsar dam watersheds, which Dehdasht and Choram
are the most important and populated cities in this area. The study
was undertaken to assess the status of water quality in the urban areas
of the Kowsar dam. A total of 28 water samples were collected from
6 stations on surface water and 1 station from groundwater on the
watershed of the Kowsar dam. All the samples were analyzed for Ni
concentration using standard procedures. The results were compared
with other national and international standards. Among the analyzed
samples, as the maximum value of Nickel (0.01 mg/L) was observed
on the station 2 at the autumn 2010, all the samples analyzed were
within the maximum admissible limits by the United States
Environmental Protection Agency, EU, WHO and the Iranian. In
general results of the present study have shown that a Ni mean value
of station No. 2 with 0.006 mg/L is higher than the other stations. Ni
level of all samples and stations have had normal values and this is an
indication of pollution potential and hazards because of human
activity and waste water of towns in the areas, which can effect on
human health implications in future. This research, therefore,
recommends the government and other responsible authorities to take
suitable improving measures in the Kowsar dam watersheds.
Abstract: Methanol-to-olefins (MTO) coupled with
transformation of coal or natural gas to methanol gives an interesting
and promising way to produce ethylene and propylene. To investigate
solid concentration in gas-solid fluidized bed for methanol-to-olefins
process catalyzed by SAPO-34, a cold model experiment system is
established in this paper. The system comprises a gas distributor in a
300mm internal diameter and 5000mm height acrylic column, the
fiber optic probe system and series of cyclones. The experiments are
carried out at ambient conditions and under different superficial gas
velocity ranging from 0.3930m/s to 0.7860m/s and different initial bed
height ranging from 600mm to 1200mm. The effects of radial
distance, axial distance, superficial gas velocity, initial bed height on
solid concentration in the bed are discussed. The effects of distributor
shape and porosity on solid concentration are also discussed. The
time-averaged solid concentration profiles under different conditions
are obtained.
Abstract: Geometry optimizations of metal complexes of Salen(bis(Salicylidene)1,2-ethylenediamine) were carried out at HF and DFT methods employing Lanl2DZ basis set. In this work structural, energies, bond lengths and other physical properties between Mn2+,Cu2+ and Ni2+ ions coordinated by salen–type ligands are examined. All calculations were performed using Gaussian 98W program series. To investigate local aromaticities, NICS were calculated at all centers of rings. The higher the band gap indicating a higher global aromaticity. The possible binding energies have been evaluated. We have evaluated Frequencies and Zero-point energy with freq calculation. The NICS(Nucleous Independent Chemical Shift) Results show Ni(II) complexes are antiaromatic and aromaticites of Mn(II) complexes are larger than Cu(II) complexes. The energy Results show Cu(II) complexes are stability than Mn(II) and Ni(II) complexes.